Search Documents

By Norbert Steiner, Roy Norcross

For the desulfurization of weak SO2 gas streams, Degussa developed a process using dilute H2SO4 solution containing H2O2 instead of conventional gas scrubbing with all solid absorbent medium (limestone, MgO). The process is based on fast reaction of H2O2 with SO2 yielding H2SO4 up to 70% strength, depending on off-gas tem­perature. Compared to the conventional systems with typically < 95% efficiency, independent on the raw gas SO2 concentra­tion, residual SO2 concentrations of less than 20 mg!Nm3 can be easily achieved, corresponding to nearly 100% removal. These features render the H2O2 process a very attractive, low capital cost technology to retrofit existing conventional desulfurization plants.

Jan 1, 1996

By R. D. Wunder

The Chino Mines Company, a Kennecott-Mitsubishi partnership, located in Hurley, New Mexico, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/ concentrator modernization commenced in 1980 and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34.0 kt/d (37,500 stpd). A new concentrator was constructed near the mine using semi-autogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of salable copper.

Jan 1, 1985

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH&apos;s that were in place within the study area, the results showed a possible elimination of 34 DDH&apos;s without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

Mine design and selection of ore processing capacity depend upon a correct estimate of the grade-tonnage distribution. The estimate must reflect what can be recovered and processed. The McCoy/Cove operation in central Nevada, USA, is a gold and silver mine. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and the log-affine variance correction. From this model, the grade-tonnage distribution was constructed. Optimal pits were generated by utilizing the distribution, and the results were compared with the pit generated by ordinary kriging. Studies indicate that the proposed method for multi-metal recoverable reserve estimation is more accurate than ordinary kriging in terms of both tons and the grade. Using recoverable reserves for mine design will maximize global recovery of mineral resources.

Jan 1, 1997

By C. Opoku-Ware, M. Kukay, P. Conrad

"This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 feet below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana. INTRODUCTION In an effort to improve Butte Area One natural resources, the research project was proposed to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU). Research by Blicker, et al. (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic VALUES ((Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown in an underground greenhouse located in the UMEC and will be planted in five areas located within the BPSOU designated for tree planting by the Butte Silver Bow government. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. They will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow."

Jan 1, 2018

By James W. Mitchell

On December 2, 1942, a scientific team lead by Nobel Prize winner Enrico Fermi first initiated and controlled a self-sustaining nuclear chain reaction. This historic event occurring beneath the stands of the University of Chicago football stadium instantly created an entirely new and tremendously broad area of technology. Indeed, the event probably changed the course of world history and considering the curret energy shortage, it probably came none too soon. Following many technological breakthroughs in the ensuing years, this event led to the first full scale nuclear fueled electric generating plant. In December, 1957, the Shippingport Nuclear Power Plant became operational and the United States had entered the era of the nuclear fueled electric generating station. Today, only fifteen years later, there are some thirty-five operating nuclear power plants in the United States with another 56 under construction and 116 on order. Still, we are only scratching the surface of this tremendous energy source. In 1970, less than one-percent of the total electric generating capacity in the United States was nuclear fueled. By 1985, it is projected that 45% of our generating capacity will result from nuclear power plants. These projections are based upoa statistics of six months to a year ago and considering the current energy shortage and recent attempts by the United States Atomic Energy Commission (USAEC) to speed the licensing process and encourage standardized plants, the contribution of nuclear power to our total generating capacity may be even greater. In summary, it is obvious that nuclear power is now, and will continue, playing an important role in our future. Those factions of government, industry and the professional community charged with fully developing this tremendous energy source must deal with it rationally, logically and expediently. The various environmental considerations in nuclear plant siting play an important role in the overall plan.

Jan 1, 1974

By R. F. Kovar, R. N. Torbin

Foster-Miller has recently developed a new concept for a highly specialized shaft lining system. This innovative shaft lining system uses a continuous slip forming placement technique, lining the shaft from the bottom up such as in a raised bored shaft. Although this part is not unique, the concept is designed to use polyurethane foam instead of concrete for the liner material. Furthermore, the concept is designed to attain rates of advance of 30 m/h (98 fph). The polyurethane foam liner is designed to be thinner (100 mm or 4 in.) than a conventional concrete liner (300 mm or 12 in.). It will eliminate the high cost associated with the erection and operation of an on-site concrete batch plant. The system will be designed to operate remotely, requiring few personnel for its operation. This system (or parts of it) may be appropriate where fast construction speed is required or where a jointless liner is needed.

Jan 1, 1990

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By L. Zhou, D. Bahrami

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time and computer-power consuming, especially for a large-scale mine ventilation network. In this paper, a direct derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the direct derivative method were verified against the results from a traditional method. The direct derivative method has been proved to be reliable and accurate.

Mar 2, 2022

By A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia (Figure 1). Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden ( > 30 m [100 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Jan 1, 1997

By H. Colijn

Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units, such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. A feeder can do many things, but it should never be considered a suction pump: During the past few years various papers have been written and presented on feeders and their application. 1,2,3,4,5,6,7,8,9)* It is not the intent of this paper to cover the same ground, and the readers are therefore ad¬vised to consult the referenced publications for supplementary information. This paper will be confined to some specific design criteria of bin feeders, such as feeder load and power requirements. Special attention is given to the basic design criteria of vibratory feeders.

Jan 1, 1968

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By Andrew I. Hustrulid

The Internet and World Wide Web create multiple opportunities to advance and change an industry. Scandura Conveyor Belting, a mid-sized manufacturing company supplying the mining industry, has embraced several of these opportunities that add value to the sale and service of the manufactured product. This paper presents a technical overview of available technology and how it is being applied to advance the conveyor belt industry. These technologies are used to provide historic catalog information, interactive troubleshooting, product installation and service instructions, detailed product information, technical calculations for the proper conveyor belt selection, and on-line site surveys and maintenance logs.

Jan 1, 2002

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By C. H. Sheerin

Remotely located in the jungle near mount Puncak Jaya [16,500 ft (5,030 my), Irian Jaya, Indonesia rests Freeport&apos;s Indonesian copper mining operation. Shortly after start up of Freeport&apos;s copper concentrator in 1972, lower than estimated throughput was experienced within the crushing circuit. Within one year, Freeport had successfully engineered a solution, and was operating a 5,500 dmtpd wet screening circuit. Today, after 19 years of successful wet screening expansion and operation, the concentrator processes 57,000 dmtpd.

Jan 1, 1993

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train, the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71 percent — as confirmed by real operational data from the Antapaccay Mine in Peru. It was the first plant worldwide to use gearless drives for both applications.The gearless principleThe principal idea behind a gearless drive system is to reduce the number of components and diversity of parts, especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material.In order to apply this principle of simplification, the components of a conventional drive system are examined. They consist of:• Driven equipment (mill, conveyor, slurry pump).• Components altering the rated speed (gearboxes, girth gear/pinion).• The electric motor.• Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage.• Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation.• The electrical supply system (cables, switchgear, transformers, protection equipment)."

Jan 1, 2015

By L. Thompsen

High pressure grinding has been introduced into many grinding applications. The high pressure grinding roll offers capacity increases of existing plants and savings in operating costs. Also metallurgical advantages could be achieved. The first high pressure grinding roll in a copper mine was commissioned in Arizona in July 1995. This paper provides information about the operating experience gathered during the first months of operation. The current flowsheet will be described as well as further options for plant arrangements.

Jan 1, 1996

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

The abstract discusses the issue of mine equipment fires caused by hot surface ignition of flammable liquids. The research investigates the ignition probability of liquid fuels (diesel, engine oil, hydraulic fluid) on different metal surfaces (stainless steel, cast iron, carbon steel) under various ventilation speeds. The results show that the type of metal and ventilation speed influence the ignition temperature, with diesel being the most easily ignited fuel and carbon steel requiring a higher ignition temperature. The study provides data for understanding equipment mine fires and developing mitigation strategies.

May 4, 2022

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985