Search Documents

By J. S. Roti

Calcium-based scale precipitation is a common problem in mill reclaim waters. An accumulation of these adherent deposits can result in a rapid reduction in water flow, loss of pump efficiency and eventual interruption in ore production. Heap leach applications can also experience the added problems of plugged sprinkler heads, blinded leach pads and fouled carbon columns when scale control is not maintained. The primary cause of scaling in precious metal recovery is the relative insolubility of calcium carbonate. The presence of the calcium ion and bicarbonate alkalinity is common in almost every water source. If the temperature or pH of the water is allowed to increase, the bicarbonate breaks down to carbonate and combines with calcium by the following reaction: Ca +2 +2HCO3 ? CaCO3 + H2 + CO2

Jan 1, 1986

By L. Alagha, F. Schott, M. B. Haya, Z. Xiao, K. C. Monyake

"Froth flotation is a process in which valuable minerals are separated from gangue minerals on the basis of surface wettabilities. It is a universally accepted process for the beneficiation of coal. The large amount of coal fines that have been generated from both mining and beneficiation processes has been reported as a chronic problem to both fine coal preparation and utilization as these fines contain a high amount of ash forming minerals. The current study investigated the potential application of Synthetic Bio-compatible Polymers as slime depressants in fine coal flotation for the possibility to enhance the combustible recovery and ash rejection. Raw coal samples containing 21% of ash-forming minerals were crushed, grinded and floated in the presence of Chitosan polymer. Flotation tests were carried out in D-12 Denver flotation cell with 1-Liter capacity. Flotation outcomes were studied as a function of polymer concentration. Box-Behnken factorial method was used for experimental design. Second order response functions were produced for ash% and combustible recovery. The results obtained from this study demonstrated positive influence of chitosan polymer on ash% and combustible recovery. Ash % was decreased by 3.32 % while an increase of 48.15 % in combustible recovery was observed when chitosan was introduced in the flotation process. INTRODUCTION Froth flotation is a widely used method of separating minerals by utilizing the difference between surface wettabilities [1], [2].Modern mechanized mining and ore handling operations produce large amounts of coal fines which in the past were not processed but discarded as waste[3]. Even though flotation is the best method of beneficiation for coal, it can be challenging in case of fine coals. In fine coals, slime coatings of colloidal mineral matter exist on the coal surface. These coatings render the coal hydrophilic, hence reducing flotation efficiency and recovery. Of late, different researches have been using biodegradable polymers to determine their feasibility in enhancing fine coal flotation efficiency[4].Naturally occurring and synthetic polymers, for example, polyacrylamide-based polymers, have been widely used in flotation as multifunctional reagents[5],[6],[7]. Hybrid polyacrylamide polymer has been successfully used as a depressant for ash forming minerals in fine coal flotation[3]. Recently, chitosan has been successfully used in flocculating quartz particles to produce faster settling rates of fine tailings [4]."

Jan 1, 2018

By J. Potter, A. Anani, C. Antonio

This research aims to test the hypothesis that the low retention rate of women in the mining industry is caused by workplace culture and policies established due to gender segregation. A quasi-experiment is developed to determine the cause-and-effect relationship between gender segregation-inspired culture and the retention of women. The experiment considers the impact of the job type and the operational environment. The analysis provides information on factors that cause low retention of women in the industry, the extent to which gender segregation plays a role, and insights that allow actionable and measurable changes in the industry.

Feb 1, 2023

By Hugh E. Cronin, Joseph J. Coluccio

The Columbia Slough Consolidation Conduit Project is a 12 ft. 0 in. inside diameter—15 ft. 4 in. excavated diameter tunnel, 8,300 lf. in length. The tunnel is divided in two parts a 4,460 lf. reach to the West and a 3,770 lf. reach to the East separated by a flow regulation structure in the middle. The project was built for the City of Portland, Oregon Bureau of Environmental Services (BES) by the Frank Coluccio Construction Company (FCCC) Seattle, Washington under a $22,600,000.00 contract starting in 1998 and completing the contract in 2000 at a total cost to the City of $25,448,000. An increase of 12.6% from the original contract. The tunnel was constructed in an alluvial sediment that ranges up to 1,500 feet thick. The sediment varies from ?ne silty sand and sandy silt (SM-ML) to coarse sand and gravel (GP-GM) with varying quantities of cobbles and boulders. Most of the tunnel was constructed above the water table although one reach of almost 1,000 lf. had water to above the tunnel crown. The contractor, FCCC, used a Lovat 15 ft. 3 in.900 hp shielded TBM with multiple doors (4) of variable opening to excavate and support the tunnel. Tunnel supports were 5 in. WF 16 lbs. per foot at 4 ft. spacing and4 in. Douglas Fir lagging. Tunnel excavation was worked in 10 hour shifts with additional equipment maintenance and repair on the off time. The original Geotechnical Design Summary Report (GDSR) established a baseline for contractual purposes of slightly over 5 boulders (between 12 in. and48 in.) per foot of tunnel. (Table 1) At the pre-bid conference, three test pits were excavated to approximately tunnel invert, one at each end of the project and one in the middle near the flow regulation structure. The test pits encountered a few boulders but did not seem to support the five boulders per foot (varied from one boulder per foot of tunnel to eight b/lf.). Subsequent to the pre-bid meeting and the test pits, BES issued any addenda which changed the baseline boulder quantity in the GDSR to 1.7 boulders per foot of tunnel (varied from0.2 to 3.5 boulders per foot) a reduction of 67% from the original baseline. It is interesting to note the two separate tunnel reaches and how they were evaluated in the GDSR. Originally the Eastern portion of the work was projected at5.08 boulders per foot of tunnel and the Western portion at 5.30 boulders per foot of tunnel for a variance of less than 5%. In the revised quantity the Eastern portion was projected at 2.01 boulders per foot of tunnel and the Western portion at 1.42 boulders

Jan 1, 2003

The ventilation of a mine is one of the key elements to a successful mining operation. It is, or should be, one of the primary concerns of the mining engineer at an underground mine. Too frequently, however, insufficient thought is given to future requirements. As a result, the mines suddenly find themselves with ventilation problems that cannot be corrected economically, or in short order, and have to suffer the consequences of being on the verge of having units shut down from time to time until the venlilaltion system can be improved. Insufficient ventilation in capital-intensive mining can cause production losses, the values of which far outweigh the significant costs of providing and operating an adequate ventilation plan. Many theories, and techniques in planning and control of underground ventilation systems have been developed over the years . It is the intent of this paper to point out some of the fundamental concepts, from the practical point of view, in the design and operation of a ventilation system, with special reference to underground mines using a room-and-pillar method.

Jan 1, 1986

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

By J. M. Mutmansky, Y. J. Wang

The usual method employed to determine the direction of flow in a connecting airway in advance is to conduct a survey between the two existing nodes being connected by means of the new airway. It is then assumed that airflow will take place from the node with higher pressure to the node with lower pressure. The purpose of this paper is to examine this direction-of-flow problem -- using properties of the system characteristic curve for a two-terminal network -- and specify some conditions that ensure that flow will take from the higher-pressure node to the lower-pressure node. It is concluded that the only requirement is that all characteristic curves of fans in the network should be strictly decreasing. Five numerical examples illustrate some important properties of the direction-of-flow problem.

Jan 1, 1999

By Grant R. Brown

The objective of this paper is to describe a study sponsored by the U.S. Department of Energy during which a model was developed to optimize haulback mining procedures in single and multiple seam contour mines, The study objective was to achieve financial- based productivity increases approaching twenty percent. This paper reviews the results of the first year's Phase I activities, which include four main tasks: formulate a methodology that can be used to select equipment and mining procedures that result in optimal performance in a particular haulback mining situation; conduct field studies of representative single and multiple seam mines to obtain quantitative background information for development of the formulated methodology: develop the methodology into a useful design tool for mine operators; and prepare plans for field tests to evaluate the effectiveness of the developed tool.

Jan 1, 1981

By Allen W. Hatheway, John A. Albritton, Lloyd B. Underwood

Missouri River Division (FORD), U.S. Army Corps of Engineers (COE), has completed (October 1982) a study for the U.S. Air Force Ballistic Missile Office, in which desireable and needed changes in contracting methods for underground construction were identified. Due to the importance of geotechnical considerations in such construction, a good number of the resulting recommendations relate to geotechnical considerations. Corps contracts have traditionally served as models for contract documentation by public agencies and in private enterprise. Several standard features of present-day contracting methods were Corps innovations. Corps officials are generally in agreement with the recommendations of the Better Contracting reports published by the U.S. National Research Council (NAS/NRC), through its U.S. National Committee on Tunneling Technology (USNCTT). However, the findings of the 1982 MRD study indicate that additional changes are warranted for underground construction contracting methods; changes that deal specifically with site geological conditions, both known and to be reasonably anticipated, as well as with their associated impacts on construction. The 1982 MRD report identifies the need for nine specific improvements in geotechnical aspects of contracting; improvements based on recognition of geological conditions.

Jan 1, 1983

By Maurus Seet Hong Hua

Introduction Coal has always been China's predominant energy resource. The country ranks among the three richest countries in coal reserves in the world, next to the US and the Soviet Union. According to China's Ministry of Coal Industry (MCI), coal accounted for about 72% of the total national energy consumption. Despite efforts to increase the output of oil and hydropower, coal is predicted to remain dominant on the energy scene by increasing its share to 77% by the turn of the century. To match the rapid growth in the agricultural and industrial sectors, MCI has targeted the coal industry to double coal output from 600 Mt/a (660 million stpy) in 1981 to 1.2 Gt/a (1.3 billion stpy) by the year 2000. How is this goal to be achieved? According to MCI, it will be accomplished by: • building new underground and surface mines with a total output of 400 Mt/a (440 million stpy); • increasing the output of existing state-controlled mines from the present 344 Mt/a (368 million stpy) to 400 Mt/a (440 million stpy); and • developing and increasing the output of small, local mines run by province, county, and production brigade from the present 276 Mt/a (304 million stpy) to 400 Mt/a (440 million stpy). Building new underground and surface mines New underground coal mines will be developed in areas where the coal industry has already made headway and infrastructures currently exist. This is to optimize hardpressed capital spending on investment. Ten existing coal production bases were selected in nine different provinces that met these requirements. The underground mines scheduled to be constructed in stages at he existing coal production bases will have a total output of 200 Mt/a (220 million stpy) by the end of the century. Regarding surface mines, four mines in the Inner Mongolia Autonomous Region and one in Shanxi province have been earmarked for construction during the same period. By the year 2000, these surface mines are expected to produce 200 Mt/a (220 million stpy). Foreign equipment, machinery, and surface mine stripping technology were all involved in different degrees in the development of the five new surface mines. Some have signed joint venture agreements. Occidental Petroleum Corp. is in a joint venture with China in developing Ping-shou's 15 Mt/a (16.5 million stpy) Antaibao No. 1 open-pit. The Shentou power station, situated nearby, is anticipated to consume 3.2 Mt/a (3.5 million stpy) of the coal it produces. Some is designated for export. Increasing output There are 554 state-controlled mines that have been in operation since before 1980. They produce 344 Mt/a (379 million stpy). To increase capacity, MCI has laid out some guidelines. • Coal prospecting near existing mines must be given top priority and intensified so that workable reserves can be increased. This would lengthen the mines' useful life. • Many mines and slopes that were constructed during the 1950s are very small and densely populated. These small mines and slopes are generally very short along the strike. As a result, coal faces and levels require frequent

Jan 3, 1986

By Michael Edesess

The salt gradient solar pond has been the focal point of accelerating international attention and interest in recent months. Only recently have most investigators in the renewable energy field come to realize the versatility of the solar pond, and its ability to overcome certain problems usually associated with solar technologies. These realizations, together with clear demonstrations in Israel and elsewhere of its technical feasibility, have combined to bring the solar pond to the forefront of renewable energy technologies. The solar pond is a natural or site-built pond, about one to five meters or more in depth, which has been altered to retard the loss of absorbed solar energy. The absorbed solar energy is usually lost through upward buoyancy of the warmed water, followed by the loss of its heat to the atmosphere. The chief solar pond technology -the salt gradient, or "nonconvective" solar pond-prevents this upward buoyancy by means of a vertical density gradient achieved with dissolved salt. The deep waters in the solar pond reach high temperatures, up to and even above the boiling point of pure water.

Jan 1, 1981

By Deborah Muggli

Minera Escondida is the world's largest copper mine. Its capacity is more than 800 kt/a (880,000 stpy) of copper. The Escondida open-pit mine operates at an elevation of 3,100 m (10,170 ft). It is located in the Atacama desert about 160 km (100 miles) southeast of the port of Antofagasta. At Coloso, 14 km (8 miles) south of Antofagasta, copper concentrate is dewatered by filtration for storage and shipment to overseas markets (Fig. 1). Concentrate filtrate water, after being treated to remove suspended solids, is discharged at 60 m (200 ft) depth into the Pacific Ocean. This effluent is free of particulates. However, it does contain metal levels above US Environmental Protection Agency (EPA) receiving water criterion. EPA standards are more strict than Chilean receiving water guidelines. However, a multiport diffuser provides rapid mixing of sea water with effluent to ensure metal levels in the receiving water remain below EPA receiving water guidelines. The Escondida Mine began operation in December 1990 at a rated mill capacity of 35 kt/d (38,500 stpd). Since then, the complex has since undergone three expansions. In 1996, it processed 115 kt/d (127,000 stpd) of ore. At Coloso in 1993, about 25% of the copper concentrate was fed to an ammonia leach plant for solvent extraction and electrowinng of cathode copper. This plant is designed to produce 80 kt/a (88,000 st/year) of cathode copper. In 1995, the ocean diffuser system's capacity was doubled to accommodate increased flows to a maximum 50 L/sec (793 gpm). This was achieved by extending the diffuser chamber by 32 m (105 ft) and adding 16 nozzles, which doubled the diffuser's capacity. In November 1996, Rescan Environmental Services began a field verification of the outfall/diffuser system's performance. The study's objective was to determine the performance of the outfall/diffuser system by measuring dilution factors using fluorescent Rhodamine dye and to determine if copper concentrations are below the US Environmental Protection Agency (EPA) water quality criterion of 2.9 µg/L total copper (EPA, 1986). Rhodamine dye was injected into the outfall/diffuser system. An oceanographic survey using an in situ fluorometer was conducted to measure dye concentrations in the effluent plume. Water column characteristics were also measured. These included current speed and direction.

Jan 1, 1997

By Joseph T. Duncan, Syd Peng, Larry G. Stolarczyk

The mining business has numerous risks: equipment availability, labor disruptions, foreign exchange rate, etc., but one of the more important risks is assessing the geology. Improving the “intelligence” of geology can and will have significant positive effect on reducing mining risk and thus enhancing operational and financial performance. The use of the advanced Radio Imaging Method (RIM-IV) on coal seams and ore bodies can create useful two-dimensional (2-D) and three-dimensional (3-D) high-resolution images that provide mining engineers with additional intelligence to better plan and improve operations. Improved operational performance will reduce costs and enable mining companies to meet market and financial commitments. For the past decade the underground coal mining industry has been moving toward “super panels” in long-wall mining, and “super sections” for room-and-pillar mining. These mining conventions employ wider faces, longer gate roads, greater room-and-pillar density, and an increased scale in the amount and complexity of mining equipment. An obvious economy of scale exists: amortization of setup investments over greater volume of coal enables mine management to reduce fixed cost per ton. Restricted by equipment considerations, face widths have currently reached about 1,100 ft. Wider longwall panels are planned, with 1,400-ft widths, but this requires an incremental step in hardware that the original equipment manufacturers will soon bring to market. However, longwall panel length has not yet reached its limits, with some panels planned up to 25,000 ft. While longwall panel length is generally dictated by reserve size and extent, practical restrictions in mine planning also include seam thickness, ventilation requirements, or restrictions involving methane drainage. Super panels have certainly enabled the industry to keep pushing the limits of productivity improvement. However, important considerations in mine planning, now and especially in the future, will be driven in large part by geological factors. While larger developments improve productivity and capture economies of scale, the fact that super panels can contain at least four times the area or coal volume means that the probability of encountering serious anomalies is at least four times greater than with the “conventional” panels. Given the increased probability of encountering anomalies, improved assessment of geology is important for super panels and super sections. Proper due diligence requires a thorough and competent evaluation of a mining property and its ore reserve. Using improved geostatistical techniques is most important, and improving the base data for the analysis is equally important. The old cliché “garbage in, garbage out” certainly applies. Also, the quality of coal reserves is (or has been) declining, so, in the future, mining will be in deeper and most likely thinner seams—and these seams appear to contain greater anomalies that threaten efficient operations. To counter the impact of reserve deterioration, the industry is moving toward greater use of geophysical tools and services. Fortunately, tools such as the Radio Imaging Method™ (RIM-IV) system have been improved and can provide the industry with enhanced 2-D and 3-D images of coal seams and ore bodies. To identify and profile the best areas of a coal reserve, geologists, engineers, and mine managers need greater intelligence in the form of RIM-IV tomographic maps of longwall panels and room-and-pillar sections. These images have enhanced the understanding of in-seam features, which in turn has improved operational plans and performance.

Jan 1, 2005

By Bo Hyun Kim, Mark K. Larson

This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock-mass behavior in longwall coal mines in highly stressed, bump-prone ground. The floor-heave and nofloor- heave phenomena at a western US coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria (i.e., Mohr–Coulomb or Hoek–Brown failure criterion). The previous numerical study demonstrated these phenomena using a user-defined model of the s-shaped brittle failure criterion in conjunction with a spalling process in the FLAC3D numerical modeling software. The results of the FLAC3D modeling agreed with the observations of the relative amounts of heave from each gate-road system. However, the FLAC3D model adopted many assumptions and simplifications that were not very realistic from a physical or mechanical perspective. To overcome the limitations of the FLAC3D model, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. The effect of stress rotation in the mining-induced stress field was considered by using a different geometry of rock fractures in the coal seam. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) were also considered by using Monte Carlo simulations. Consequently, the 3DEC models using the DFN technique resulted in predictions of floor heave that agreed with observations of the relative amounts of heave from each gate-road system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Apr 14, 2022

By Brian E. McGee

The Federal Coal Management Program represents the culmination of several years of effort by the Department of the Interior (001) to reformulate the manner in which coal owned by the United States is leased and developed. These efforts began in 1970 with a study by the Bureau of Land Management (BLM), which indicated that unless drastic changes were made in. the federal coal leasing procedures, federal coal lands would be leased almost for the asking while production of coal from those lands had been decreasing. Consequently, informal action was taken in 1971, which resulted in no further leasing being authorized until February, 1973. At that time, a formal moratorium on most coal leasing was established, with exceptions granted only for leases needed to satisfy short-term needs such as maintaining existing mines or supplying reserves for new contracts in the immediate future. This leasing policy embodied a long term objective of developing an entirely new planning system for federal coal leasing, as well as to schedule the preparation of a programmatic impact statement for this new system. As a result of the 1973 moratorium and the ensuing application of short-term criteria, only 10 federal coal leases (covering approximately 30,177 acres) were issued from February, 1973, through January l, 1976.

Jan 1, 1982

By Edward P. Larsen

At our annual meeting in St, Louis, Mo. in February 1961, we presented a comprehensive paper (No. 61-B-22) on the subject of "Blending and Handling of Materials for Agglomeration". In that paper you will find a discussion on the difference between "blending" and "mixing". With regard to "blending" we brought out the facts of its usefulness for the preparation o materials in an agglomerated mass to attain controlled chemical and physical uniformity. "Mixing" was discredited as not being useful for the attainment of uniformity of any kind.

Jan 1, 1962

By D. Randall Crooke, Ron R. Jorgenson

Many coal combustion products (CCPs) have historically been unsuitable for placement as mine backfill because of their physical and geochemical properties and/or regulatory status. However, innovations in paste production and transport of CCPs utilizing the high, fine particle contents of these fine-grained waste materials and their water retention colloidal properties produce a non-segregating, self-cementing material that may be environmentally suitable for placement as mine backfill. Both industry and the regulatory agencies are enthused by the possible cost reductions, both in design and construction of disposal sites, and the reduced environmental impacts of CCP realized by implementation of this new use/disposal technology.

Jan 1, 2001

By T. P. Meloy

In the last decade increased and prolonged interest has been displayed in the use: of tunneling or rapid excavation to solve many of the urban and industrial problems confronting our society. There has been talk and action on the interurban rapid transit systems for major cities, and even preliminary designs for a Boston to Washington interurban transit system. Much of this interest stems from the search to the solution of our increasingly complex urban problems, where the surface area must be given over more and more to the inhabitants, and the subsurface for transit, utility and other services. While tunneling is not a panacea to urban ills it holds a real solution to many existing problems. There is also, among the tunneling experts, a growing confidence that technical problems of rapid tunneling can be solved. To solve these problems, R & D money must be invested. If it is to be money invested either by private industry or governments, there must be significant returns on the investment to justify the research and development need to bring about the breakthrough that will make tunneling a major contribution to the solution of urban problems. To make these economic studies more extensive and more accurate tunneling demand figures were needed. To this end, the Organization of Economic Cooperation & Development - OCED - included in its Conference on Tunneling a section on tunneling demand. As a result of the conference the organization for Economic Cooperation and Development issued a report entitled "The Advisory Conference on Tunneling - Report on Tunneling Demand 1960-1980. " This report was presented at the OCED Conference on Rapid Excavation, held at Washington, D.C. To obtain the data in the Report, questionnaires were sent to the OCED countries and 18 replies were received from Australia, Austria, Belgium, Canada, Denmark, France, Germany, Ireland, Italy, Japan, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom, and the United States. While it is true, that data were missing, that sometimes the definitions were confused, and that several countries provided no cost estimates at all, in general, this report contains the most comprehensive gathering of data that ever existed in the field. All data in the OECD report is expressed in terms of meters or cubic meters, and costs are in U.S. dollars.

Jan 1, 1970

By M. Abdelkhalek, M. Hepworth, D. Tao, B. K. Parekh

Pre-combustion coal cleaning and post-combustion flue gas desulfurization (FGD) using lime or limestone are the primary methods employed to reduce sulfur dioxide (SO2) emission from coal combustion. These processes generate voluminous pyrite and gypsum solid wastes that are usually landfilled, occupying thousands of acres of land and creating serious land and water pollution problems due to the release of acids and toxic substances. An integrated process has been developed for the combined utilization of gypsum and pyrite wastes by converting them into useful products including lime, sulfur, and direct reduced iron (DRI). The process includes four major steps. The first step is to concentrate pyrite from coal preparation tailings using flotation or gravity separation. The second is the thermal decomposition of pyrite into pyrrhotite and sulfur. This is followed by the reduction of pyrrhotite with carbon in the presence of lime to produce iron and calcium sulfide. The fourth step involves the reaction of calcium sulfide with gypsum to produce lime. The chemical reactions involved in the process were studied using thermogravimetric analysis (TGA) and X-ray diffraction (XRD)techniques. Process variables studied included reaction temperature, time, reactant composition, and purity of reactants.

Jan 1, 2000

By Irving Hauser

The determination of new ways to cut costs in then times of economic uncertainty is essential in running a successful business. Arco Petroleum Products Company a Division of Atlantic Richfield Company recognized an opportunity for a substantial cast savings in transporting calcined petroleum coke to market by simply building an economical port facility at a location that would enable them to drastically cut their normal rail haulage distance.

Jan 1, 1982