Search Documents

By Michael A. Werner

"A Yieldable Structure for Use in Areas of High Rock Stress & Deformation." Rock stress of up to 9000 psi have been recorded in the mines of the Coeur d'Alene Mining district. Associated with these large stresses are rock fractures and deformation. In order to maintain openings required for mining, large wood preparation structures are constructed to provide access to the work areas for men and materials. These wood raise preparation structures are costly to construct and maintain. Therefore a steel-foam concrete structure was designed and proposed for testing which would be less costly to construct, require no maintainence and maintain its structural integrity while allowing up to 53 inches of wall rock deformation.

Jan 1, 1984

By G. H. Friedrich

The distribution of mercury in soils, rocks, and ore was studied in three areas of the Pachuca-Real del Monte District: (1) An area north of the town of Pachuca where ore veins have been found at or near the surface. The mercury content of soil samples taken near the vein zones is far above the background value. The highest value was 1900 ppb (parts per billion) mercury in a soil sample above Veta Vizcaina; the background is about 50 ppb Hg. (2) In the area north of the town of Real del Monte where only a few of the veins are known to crop-out. Regardless of exposure, soils collected over veins show anomalous mercury values ranging from 250 ppb to 1900 ppb. (3) In an area south of the town of Real del Monte. Here, although vein outcrops are lacking, mineralization is known at a depth of about 120 m. All soil samples taken at 50 m. intervals along an east-west traverse contain anomalous amounts of mercury, with peaks corresponding with the known location of the veins.

Jan 1, 1965

By D. P. Caplice

On behalf of the Ontario Water Resources Commission, I would like to express my sincere appreciation to your Institute for presenting us with this opportunity to outline the regulatory control programme as it relates to the mining industry in the Province of Ontario. In Canada, and particularly in Ontario, we are blessed with an abundance of natural resources. Fresh water in the form of lakes and rivers covers nearly 17 per cent of the area of the Province. (Total area of the Province of Ontario is 412,582 square miles.) The mining industry, which had its beginning in the early 1800's with a small iron ore plant, has progressed with the major discoveries of nickel and copper in 1883, silver in 1903, gold in 1908, iron in 1939 and uranium in 1953, to the point where, in 1966, almost one billion dollars in mineral wealth was mined in Ontario. Water, in spite of its great abundance and with due respects that it may become a natural resource worthy of export in the foreseeable future, has become increasingly precious in Ontario, particularly in the more urban areas in the southern part of the Province.

Jan 1, 1968

By Hans von Michaelis

The renaissance in extractive metallurgical practices for gold and silver recovery is far from over. This is one conclusion of a three year investigation into innovations in Cold & Silver Recovery by Randol International Ltd. (1981, 1983). The six volume reference report reviews a host of new processes and innovative applications of older metallurgical practices. Some of these were summarized by von Michaelis (1982, 1982a). There are several reasons to expect this renaissance to continue. One reason is the nature of gold and silver deposits. The list of known occurrences of These metals is very extensive. There are literally tens of thousands of prospects but over 99% of these are too low grade, too small or too refractory for a viable operation employing conventional processing.

Jan 1, 1983

Clean Diesels fuel-borne catalyst, Platinum Plus, helps improve fuel economy for all engines up to 10 percent while reducing particulate emissions by up to 25 percent. When used with a simple diesel oxidation catalyst, particulate emissions can be reduced by 30 to 50 percent. The use of Platinum Plus enhances combustion in the cylinder, burning fuel more completely. This reduces CO2 and other greenhouse gases and lowers total operating costs by improving fuel economy.

Jan 1, 2007

By E. Steiakakis, A. Athousaki

Nowadays, stakeholders have a strong say to the enforcement of best practices by mining and quarrying companies. In most cases there is a direct relationship between sustainable development principles and best practices. Mining companies try to apply best practices in order to sustain their operation without lost time and effort to litigation, and other obstacles. However, when and where there is a lack of state or regional mineral policy, or when the mineral policy is fragmented and touching on conflicting laws, mining operations may be subject to additional administrative hassles, and, thus, operators feel threatened and tend to apply best practices loosely. This paper argues that the only way that mining and minerals operations can be a source of development is to ensure that they are working within the framework of sustainable development. Furthermore, in order to follow the paradigm of sustainable development they would need to be guided by a regional, national or even transnational (i.e. European) minerals policy.

Jan 1, 2011

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By Glen Frank, David R. Chapman

Determining the number of boulders and cobbles that will be encountered in the tunnel envelope is one of the most difficult problems confronting the geotechnical engineer in the design of tunnels in glacial terrain. This issue is very important to the contractor, both in determining what methods will be used to construct the facilities and the advance rate that can be achieved for the chosen construction methods. The cost of constructing tunnels by pressurized face tunneling techniques is very sensitive to accurate characterization of the very coarse fraction (large cobble and boulder sized clasts), and no standard method is current available for characterizing boulders and cobbles. Careful use of large diameter borings and the sampling and analytical techniques outlined in this paper can provide a means to answer this difficult question. By performing large diameter borings and carefully recording and sampling the cobbles and boulders encountered, an estimate for the amount of these materials present in the formations sampled can be provided. Using this method allows the designer to communicate the expected geologic conditions to the prospective bidders in a manner that is both definitive and defensible. This paper describes the method as it was used in conjunction with the design of a large diameter sewer tunnel in the Columbus, Ohio area.

Jan 1, 2005

By R. Yang

This paper presents a kinematic approach for blast modeling with examples of blast models that were developed previously. A kinematic approach was applied successfully in developing blasting models that can simulate all blast design parameters for field applications. Several applied blasting models have been developed and applied widely in the world. A kinematic approach to blast modeling refers to using measurements of kinematic quantities such as the velocity, strain, or displacement and well-established assumptions to model blasting phenomena, rather than being restricted to use first principal of physics, such as, the stress- and material-constitutive relations. The kinematic quantities are easy to measure in the field. Due to the complexity and inhomogeneity of rock mass properties, using first principles of physics, many parameters of rock and explosive properties must be involved, which are hard or impossible to quantify. This creates a major impediment when trying to simulate the total process of blasting based upon first principles of physics. The 3D kinematic model for muckpile formation was developed and applied to open pit blasts. The multiple blasthole fragmentation model developed during recent years has been applied successfully to many mine sites around the globe. These models are typical examples of blast modeling using the kinematic approach, which enables the models to catch major trends of the blasting process and explicitly simulate full blast design parameters and complex geometries. Blast modeling using the kinematic approach results in easy model calibration and validation against field measurements and effective applications to practical problems. Using kinematic models of the muckpile formation and the multiple blasthole fragmentation model, this paper demonstrates the merits of the kinematic approach for blast modeling. New developments of the models were also presented in the paper, which illustrate the potential of the kinematic modelling approach.

Mar 2, 2022

In the present study, we have investigated the conditions for the formation of bubble clusters and the effect of well-defined agitation on the stability of clusters. A specially designed cell was used in which bubble clusters could be formed at the surface of a porous block in a fluidized bed of relatively coarse hydrophobic silica particles. The clusters then rose through a flow field of known turbulent characteristics. The size of the clusters before and after passing through the turbulent zone were measured using a high speed camera. The influence of shear rate on the deformation of the bubble clusters was investigated. The results showed that the Kolmogarov microscale was much smaller than the maximum cluster size, suggesting that the breakage of the clusters was mainly due to interaction with clusters in the inertial convection sub-range.

Jan 1, 2009

By J. Hahn

Modern high-performance disc filters such as the BoVac Disc Filter have set new standards in applications where large capacities of solids, liquids and air have to be managed through the filters. These disc filters have an enormous hydraulic capacity. For applications in mineral processing - with a special focus on tailings – which typically have high solids throughputs but low filtrate and air flows, this capacity can be used to expand the filtration area while maintaining the benefits of very good cake discharge even with thin cakes (4-5 mm) and a high filter speed. Research work over the last century has proven that increasing the filter area should be achieved by increasing the disc diameter. Because adding more discs leads to big problems with the cake discharge. However, as the disc diameter increases, the filter segments become longer and heavier. A suitable compromise was therefore found by doing both. The result is the first vacuum disc filter that offers significantly more than 300 m² of filtration area, but has no more than 6 discs.

Feb 1, 2023

By J. A. Ober

China, Mexico, Spain and Turkey are the leading producers of celestite (strontium sulfate), the most common strontium mineral. Of an estimated 510 kt (562,000 st) of celestite produced worldwide during 2004, 98 percent was produced in those countries. Deposits of strontianite (strontium carbonate), another strontium mineral, have been identified in China and Malawi. Relatively small quantities are reported from the deposit in China. Although celestite deposits occur in the United States, no domestic celestite has been mined since 1959.

Jan 1, 2005

By C. Garcia, C. L. Lin

Characterization and analysis of multiphase particles and/or particulate systems (such as the packed particle bed) are of great technological importance for mineral processing applications. In general the performance of these applications depends on the statistical characteristics of particle microstructures, such as composition distribution, surface exposure of mineral grains, pore network structure, etc. For continued technological progress in the field of multiphase particulate processes, the need for quantitative spatial analysis of multiphase particles in three dimensions has increased sign6cantly. Such quantitative information must be accurate enough that the measured values can be used as parameters for simulation models, process design procedures, and control strategies. Modern 3D image-acquisition techniques, such as X-ray microtomography (XMT), offer a unique imaging capability that can produce high-resolution (a few micrometers) three-dimensional images of the internal structure of multiphase particulate samples. These three-dimensional image data present new challenges for image analysis, image processing, and visualization. Furthermore, important issues should focus on how to use the 3D information and derive new insights into the improvement, design, and operation of mineral processing processes. In this paper, utilization of XMT for characterization and analysis of leaching process involving multiphase particulate system is discussed.

Jan 1, 2005

By Y. P. Chugh

During late 2010, a scientifically founded water spray system was developed for continuous miners (CM) (Patent Pending) that reduces respirable dust exposure for miner operator by about 30%. It includes engineered sprays around the cutting drum, outer bit-ring sprays, chassis sprays and side cutter boom sprays. About 3.6 ? 4.5m (12-15 ft) behind these sprays is additional sprays that spatially cover the area between the CM chassis and the mine roof and ribs. The spray system uses approximately the same volume of water as currently used on CMs with similar operating pressures. An Illinois mine decided to implement these concepts on a CM during rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric sampling and real-time monitoring using multiple personal dust monitors (PDMs). The average results based on about 105 cuts show about 30% and 20% reduction in dust exposure for the miner operator, and the haulage unit operator. Visibility in the mining areas was also significantly improved. The coal company has already decided to implement the system on all their CMs.

Jan 1, 2012

Waste areas of a mine should be sealed especially if there is a risk of spontaneous combustion. Leakage through and around such seals can be problematic. Pressure balancing has been one of the favored options to prevent the ingress of air into these waste areas. Balance chambers require maintenance and monitoring to ensure that they are effective. This paper explores the use of inert gas as a means of controlling ingress of air and egress of waste gases as a means of reducing leakage around seals.

Jan 1, 2009

By Raquel Costa, Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, Ana Filipa Marques, Andreia Afonso, Maria Ana Martins, António Calado, Luísa Pinto Ribeiro

Since its formation in 2004, the Task Group for the Extension of the Continental Shelf (EMEPC) has been collecting hydrographic, geological and geophysical data to support the extension of the continental shelf beyond 200 NM. In 2008, the EMEPC acquired a 6,000 m rated ROV named "Luso" and has been cooperating with several national and international institutions to increase and improve its operational capabilities to conduct research on deep-sea minerals. The Portuguese continental shelf corresponds to a broad area of the seafloor encompassing different physiographic domains: the mid-Atlantic ridge system, abyssal plains and numerous seamounts. From 2008 to the present, the mid- Atlantic ridge and seamounts have been the most visited sites with the ROV "Luso". Several hydrothermal vent sites are known to occur along the mid-Atlantic ridge to the south of the Azores archipelago and mostly within the Portuguese EEZ. Vent fields were also discovered in the extended continental shelf, namely the Rainbow and the Moytirra sites located to south and to the north of the Azores archipelago, respectively. The most studied seamounts correspond to those forming the Great Meteor chain and the Madeira- Tore rise. All these visited sites are related either with the occurrence of polymetallic sulphides or cobalt rich Fe-Mn crusts and the opportunities to further pursue their exploration will be discussed.

Sep 1, 2014

By J. L. Hoover

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect bit drill wear and use the equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel Software. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By Emily Wortman-Wunder

While the mood at the 2013 annual joint meeting between the Pittsburgh Coal Mining Institute of America (127th Annual Meeting) and SME Pittsburgh Section (68th Annual Off-the-Record Meeting) in Canonsburg, PA was subdued following a rocky year in the coal industry, attendance was down only slightly, to 300, and overall, the meeting?s focus was optimistic about the future of coal. The conference began by addressing one of the central challenges of coal mining head-on with a keynote address on the status of safety in the mining industry. Noting that two more U.S. miners had died in 2013 than by the same date in 2012, the National Mining Association?s (NMA) Senior Vice President of Regulatory Affairs Bruce Watzman made a plea for a new approach to safety. He described the NMA CORESafety initiative, a program that promotes proactive safety measures versus a compliance-driven model. CORESafety, described in more detail on pp. 29 of this issue, focuses on developing successful ways to change company cultures of safety and behavior. Other industries that have adopted this approach have seen dramatic drops in fatalities, including the Australian mining industry, which has seen its annual fatality rate drop to nearly zero even while the number of people employed in the industry has soared. The rest of the morning?s sessions explored what is arguably the industry?s biggest challenge right now ? maintaining the social license to operate.

Jan 1, 2014

By Kimberley MacHardy, Ann Maest, Greg Lawson, James Kuipers

Although water quality predictions are often made in Environmental Impact Statements (EIS's) as part of the National Environmental Policy Act (NEPA), comparisons between predicted and actual water quality conditions are rarely reviewed. A comprehensive review of predicted and actual water quality conditions was conducted for a number of large U.S. hardrock mines with EIS’s. For mines with large differences between predicted and actual conditions, factors responsible for the deviations, such as characterization and modeling errors or engineering failures, were identified. Recommendations are made for how the NEPA process could be modified to better predict water quality at hardrock mine sites.

Jan 1, 2005

By G. A. Kordosky

LIX® 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mills' LIX® 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1976