Search Documents

By Donald G. Foot

The Bureau of Mines, U.S. Department of the Interior, devised a direct flotation method for treating low-grade carnallice (KC1.MgC12. 6H20) and sylvinite (a mixture of KC1 and NaC1) ores characterized by a high content of water-insoluble impurities. The procedure consists of (1) flocculation-depression of the insoluble slimes, (2) decomposition leach (carnallite only), (3) potash rougher, cleaner and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity of removing the water-insoluble slimes by mechanical or flotation desliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumptions. The direct flotation method recovered 81.6% of the solid-phase KC1 from carnallite ore and 79.7% of the KC1 from sylvinite ore in final products containing 60.5% and 60.9% K20, respectively. A flowsheet incorporating the described flotation procedure is presented.

Jan 1, 1981

By A. Arik

An accurate estimation of mining block grades continues to be a challenging task for ore reserve practitioners. Two of the factors that affect the accuracy of the estimates are the estimation method used and the variability of the mineralization in the deposit. The objectives of the study are twofold: Firstly, to see how different estimation methods perform on a given deposit. Secondly, to determine the impact of particular nature of the mineralization on the results. The comparison of several estimation methods for the prediction accuracy is performed using the conditional simulation results as the basis.

Jan 1, 2000

By W. Lee Daniels

Significant deposits (> 4,000 ha) of heavy mineral sands were discovered in the USA Coastal Plain of Virginia and North Carolina in 1989. The majority of these lands support highly productive row crop agriculture, and the development of restoration protocols that would return these lands to agricultural use was deemed to be critical to the long term sustainability of mining operations. Virginia Tech worked closely with all stakeholders to develop appropriate restoration protocols and to coordinate their implementation. Full-scale mining operations at the Old Hickory Project in Virginia were initiated in 1997 by Iluka Resources Inc., and restoration protocols have continued to evolve in response to a variety of economic, technical, and social issues. Approximately 750 ha of land are in various phases of backfilling and final reclamation. Return of these lands to agricultural row-crop production has been complicated by lateral variability in mine soil physical conditions, excessive compaction, and limited topsoil return. However, within the past two years, a series of tailings deposition and soil reconstruction practices have been developed and implemented that significantly improve post-mining soil productivity. Deep ripping and appropriate use of organic soil amendments have been particularly effective at restoring post-mining soil productivity.

Jan 1, 2005

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By K. V. S. Sastry, K. D. Lofftus

Mathematical modeling and computer simulation are two valuable quantitative tools that are being effectively applied to mineral process- systems. This paper presents an up-to-date assessment of process modeling and simulation, identifies a number of associated challenges and opportunities and discusses in detail sane of the aspects of applying the current state-the art modeling and computational tools.

Jan 1, 1989

By H. Maleki, G. Tetreault

This study was initiated by the Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room-and-pillar mining using a continuous miner (CM method) was economically sound, or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets" are left in longwall mines on one side of the mains, near outcrops and adverse geological conditions, or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included (1) analysis of the geologic, geo-technical, and economic factors that influence the recovery of small coal reserves, (2) analysis of historic changes in supply, demand, and coal prices, (3) development of typical cost models for room-and-pillar and longwall mines, and (4) development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR) as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modem longwall mines and thus is used to evaluate the

Jan 1, 2001

By W. E. Roscoe, K. N. Spence

In the Canadian mining industry, there are at present no comprehensive regulations or standards for valuation of mineral properties. In January 1999, the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. The authors were subsequently appointed Co-chairs of the CIM Special Committee on Valuation of Mineral Properties (CIMVal). A committee of experts from the mining industry, consulting, financial and legal communities was established with the task of reviewing available information, investigating various valuation methodologies and practices, soliciting input from interested parties, and recommending a Canadian code or standards plus guidelines for the valuation of mineral properties. As an initial stage of its work, the CIMVal Committee organized a one day session at the Mining Millennium 2000 Convention in Toronto in March 2000 on valuation of mineral properties. The 10 invited papers have been published by CIM. As a second stage, CIMVal has requested input and comments from all interested parties. The next stage will be to prepare a preliminary draft with a recommended code or standards and guidelines. This will be circulated for further input and comments prior to revision and publication of another draft. The final CIMVal report should be completed in early 2001. A variety of methods are in common usage for the valuation of mineral properties, depending on the stage of development of the property, the data available and the experience of the valuator. For example, the discounted cash flow method is commonly used for properties in production or at the feasibility stage, but is not generally considered appropriate for exploration properties. Market approaches such as comparable transactions are in wide general use, and various cost approaches are used for exploration properties. The option pricing approach has promise for valuation of marginal properties, but is not commonly used.

Jan 1, 2001

By G. Deissman, S. Kistinger

For the last 15 years environmental Life-Cycle Assessments (LCA) have increasingly been used to evaluate the environmental performance of industrial processes and products and have been employed as a basis in decision making processes in the public and industrial sector. However, assessment methodologies for environmental protection measures and reclamation/remediation measures with respect to their consumption of natural resources are generally poorly developed. In this presentation a methodology for LCA of environmental protection measures and remedial actions, respectively is suggested, using the remediation/reclamation of mining sites as an example. Key aspect of this approach is the development of an evaluation method appropriate for environmental protection measures, which links the various impact indicators recognised in the impact assessments and allows their integrated assessment.

Jan 1, 2005

By C. T. Agouridis

Head-of-hollow fills or valley fills have gained national attention due to increasing environmental concerns, particularly with regards to headwater stream loss. Researchers at the University of Kentucky in conjunction with outside scientists and consultants in the fields of stream restoration, wetland restoration, and mined land reclamation have developed new design methodologies for creating a headwater stream system for a head-of-hollow fill in eastern Kentucky. The design was largely built on the Forestry Reclamation Approach (FRA), which encourages a non-compacted spoil medium to promote tree growth, in an effort to address concerns related to water quantity and quality as well as habitat development. The major components of the design included 1) modifications to the crown geometry, 2) compaction of the crown to control infiltration, 3) utilization of natural channel design techniques, 4) use of the FRA to promote tree growth, 5) creation of ephemeral channels and vernal ponds, and 6) implementation of a novel bioreactor-wetland treatment system to improve water quality.

Jan 1, 2008

By William W. Edgerton

The California Department of Transportation (Caltrans), the Contra Costa Transportation Authority (CCTA), and the Alameda County Congestion Management Agency (Alameda CMA) are involved in a unique partnership on the planning and design of the fourth bore of the Caldecott Tunnel, located on State Route 24 in Alameda and Contra Costa counties. The project will add a two-lane bore north of the existing three bores. The project will alleviate traffic congestion in the non-peak direction. This paper provides background on the existing facility, summarizes the need for the new fourth bore, describes the proposed improvements, sets forth the approach for project delivery, and lists some of the challenges that are expected during construction.

Jan 1, 2008

By John W. Leonard

The typical tunnel boring machine in use on today's tunnel project uses 15'2-inch diameter cutters at a nominal load of 45 kips per cutter. The cutterhead rotates at a speed of 120 over D revolutions per minute where D is the cutterhead diameter in feet. The typical machine operates about 50 percent of the time. Delivery of a new machine takes 12 to 15 months. The TBM is a specialized tool and not applicable to all jobs. There is a range of job conditions that limit the economic use of a TBM. The machine should provide a thrust per cutter at least twice the compressive strength of rock in psi and up to three times the rock strength is required if in "granitic rocks." The rock strength in psi must be at least three times the cover above the tunnel in feet or the machine may stick. For example, 2,500 feet of cover requires at least 7,500 psi rock to avoid problems. When the RQD's over a significant distance of the project are less than 50, the TBM becomes support-bound. When a large percentage of the time is spent waiting while the ground is supported, the TBM cannot perform well (See Figure 1). This problem increased inversely with tunnel diameter. We are finding that increasing the RPM's does not significantly increase progress. The increased RPM results in a substantial decrease in cutter penetration. The explanation for this decrease appears to be vibration, cutterhead drag, or lack of stiffness in the cutterhead (See Figure 2).

Jan 1, 1981

By T. J. Close

The Silver Peak Range North Wilderness Study Area was deleted from the list of US Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the US Bureau of Mines mineral investigation of the wilderness study area which found indications of precious- and base-metal-resources. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Bureau examined 13 mineralized sites, most of which were previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak mining district to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz and calcite with gold, silver, and base-metals. At the surface, these veins are poorly defined. Exposures of the more than forty veins examined were as thick as 17 ft and as long as 1000 ft. Samples from these veins contained significant amounts of precious- and base-metals-as much as 0.02 oz per ton gold, 2.1 oz per ton silver, 1.0% copper, 2.6% lead and 0.4 % zinc. No vein large enough or of high enough grade to be classified a mineral resource was disclosed by the sample data. However, most do have indications of precious- and base-metal-resources at depth. Subsurface exploration of some of the veins is recommended.

Jan 1, 1995

By S. A. Lang

Mine management in general, and mine maintenance in particular, has lagged in using computers as an effective management tool. SF Coal Corporation, in conjunction with the development of the new Lee Ranch Mine, is developing a computer-based maintenance system as an integral part of a total mine management information system. The system includes the ability to schedule and plan preventative maintenance on all rolling stock and mine facilities, project and track component life, and evaluate and schedule manpower requirements. The system hardware, shared by accounting, warehousing, engineering, production and management, consists of a multi-user, multi-processor micro-computer.

Jan 1, 1985

By Takuji Yamamoto

High-speed TBM excavation requires rapid ground assessment ahead of excavation, particularly in complex grounds. The Tunnel Reflector Tracing technology (TRT) developed by authors, uses seismic reflections to produce volumetric images of ground anomalies. To further minimize interruption in the TBM excavation the authors modified surveying technique switching from cable (wired) to radio (wireless) data acquisition system. This paper presents the outline of the Wireless TRT system, and compares the results for the wired and the wireless surveys. The comparison shows that the wireless system offers high precision data, is more efficient and economical and significantly less intrusive in tunneling operations.

The status and outlook for mining, in your view. Minerals remain a major part of the world’s economic foundation. The fortunes of the mining industry rise and fall with general economic trends, but mining is no less important today on a global basis than it has been historically. Certainly, portions of the industry are critically depressed — domestic copper to name one area —but other sectors are prospering. Mineral consumption, both worldwide and in the United States, has increased steadily since the Great Depression, hitting all-time highs in 2000, the last year for which I have seen data. The highly developed economy in the United States tends to obscure the continuing importance of minerals here. But in less developed nations the critical nature of minerals is obvious and well accepted. In short, although there is no shortage of problems or challenges facing mining — there never has been — mining remains an essential business with great global opportunity.

Jan 1, 2003

By A. Sand

A 2-dimensional computational model based on the discrete element method (DEM) is utilized for modeling of stamp-charged coke making. In this process, a large volume of coal is compacted to one single coal cake before entering the coke oven. Cake densification and mechanical strength development are key factors for the subsequent production of a high-quality coke. An approach is introduced for model calibration utilizing multiple control parameters obtained from a laboratory-scale stamping device. Experimental data on stamper rebound amplitude, attenuation and peak force are compared with simulation output in a pairwise manner by constructing a criteria space, which allows identification of model settings best satisfying the control parameters. The calibration procedure carried out by multiple criteria comparison aided model parameter selection for reproducing stamper behavior in response to the properties of the cake subjected to compaction. This modeling and calibration procedure offers possibilities for numerically studying the densification and mechanical strength development of coal cakes. However, the approach is also more widely applicable to other compaction processes.

Feb 27, 2013

By P. J. Doig

The LCLS project at SLAC will allow new insights into material properties, chemical reactions and biological processes. The project includes half a mile of new underground construction. Excavation in weathered rock is by NATM, using AM 50 roadheaders. Construction began in 2006 and is expected to be completed in 2008. This paper details the construction of the tunnels and cavern on the project.

Jan 1, 2008

By Steve Kral

Not too many years ago, mining was in one of its cyclic down-sides. This forced mining companies into some innovative thinking to bring down the costs of production. And they have. Mining equipment and processing plants have become more efficient, mostly due to technological advances. The mining industry is now in a boom period, one that some analysts believe can sustain itself. But even with higher commodity prices, sky-rocketing energy costs and the costs associated with environmental and reclamation regulations have not allowed all mines to reach their full profitability potential.

Jan 1, 2006

By W. H. Schiffbauer

The U. S. Bureau of Mines has been investigating methods and technology that, when applied to existing continuous coal mining machines, may improve production and safety. Toward those goals, a microcomputer network has been designed that provides automated control and monitoring of all mining machine systems using a single twisted pair cable (two conductor stranded wire twisted together to provide a level of noise rejection). The network also provides -connections for intelligent sensors and systems for navigation and diagnostics. The flexibility of the network is demonstrated in that features can be added and removed without redesigning the whole system. A general description of the network's integration to a Joy' 16CM, Joy 14CM, Jeffrey 102, and a custom built auger machine is provided. The microcomputer networks for the Joy 16CM and the Jeffrey 102 have been installed onboard the mining machines and have been extensively tested at the Bureau of Mines test facility. The Jeffrey 102 system has also been tested in an actual highwall coal seam. Both systems have performed satisfactorily. The microcomputer networks for the Joy 14CM and the Auger Miner have been tested and await installation on the respective machines.

Jan 1, 1990

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994