Search Documents

By Lukas Walder, Roland Arnold, Raphael Zuber, Richard Gradnik

This paper presents the construction of the ventilation shaft for the single-tube, doublelane Kramer tunnel. The project is located in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of Garmisch-Partenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million incl. VAT (US-Dollar 201 million), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for singletube tunnels is solved by a parallel escape tunnel passable for vehicles. For tunnel ventilation, an intermediate shaft has been designed with a depth of approximately 90 m (295 feet) and an inner diameter of 4.5 m (14.8 feet). All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). The geological and hydrogeological conditions, the change in the profile (from round to square geometry), and also the shaft being located at a high elevation presented a demanding technical and logistical challenge. The site arrangement with the pit bank was located in a cut, the slopes of which had to be stabilized with shotcrete and soil nails. This excavation was carried out from the fall of 2020 to the beginning of 2021 because construction operations had to be completed outside the nesting period of protected birds.

Jun 13, 2023

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By V. A. Evans

The preparation of a paper reporting fluorspar economics in the United States at one point in time could have been somewhat complicated be- cause of the number of producers, both large and small, that derived production from different locations throughout the Western U. S. and the Southern Illinois and Western Kentucky fluorspar districts . Companies such as Allied Chemical and William- son Mining operated in the Jamestown district of Colorado. In Walden and Salida, Colorado, the Colorado Fluorspar Company operated mines and mills.

Jan 1, 1986

By Magnus Ericsson

The unexpectedly quick recovery in world crude steel production in the second half of 2009 was due almost entirely to increased production in China that began in late 2008. Previous peaks in monthly production in China were matched by April 2009. The rest of the world had still not reached pre-crisis production rates by May 2010. Chinese production drives growth, but there has been some growth in most other larger crude steel producing countries as well, compared to production in 2009. If the production rate of the first four months of 2010 continues, the total output of crude steel in 2010 will be somewhere around 1,410 Mt (1.5 billion st), the same as in the record year of 2007.

Jan 1, 2010

By H. Dreissen

Upgrading of low-concentration ores is of growing importance today. The Heavy Medium Cyclone Process, thanks to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses the separation efficiency, the method of assessing that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants handling following minerals are reported: barite, wolfram, iron, magnesite, diamond, lead-zinc, fluorspar, rocksalt potash. Highlighted are an improved recovery system for heavy medium and some other developments, such as techniques for separation down to 0.1mm and the application in the field of recycling.

Jan 1, 1980

By D. R. Wilburn

his summary of international mineral exploration activities for the year 2011 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents [ ] analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2011 as compiled by the USGS and 3) regional events including economic, social and political conditions that affected exploration activities, which were derived from published sources and unpublished discussions with USGS and industry specialists.

Jan 1, 2012

By William H. Peterson

How is the Government's oil import control program doing? In July 1954 Mr, Eisenhower established the Cabinet Committee on Energy Supplies and Resources Policy. On July 29, 1957, the Administration imposed "voluntary" company oil import quotas on American oil importers to maintain "a healthy domestic (oil) production industry" and safeguard "national security." On March 10, 1959 the President by proclamation made the voluntary program mandatory. But study of the program in practice shows that it is not working out as expected and-that there is some doubt that its aims and other related Administration purposes are being achieved. Take the Administration's anti-inflation policy. To be sure, the President apparently recognized in his March 10th proclamation that in restricting cheap imported oil in favor of more expensive-domestic oil he was making the inflation fight that much harder, for he called for Government surveillance of domestic oil prices to prevent them from getting out of hard, And indeed while domestic crude oil prices have not risen appreciably during 1959 neither have they fallen appreciably (although there has been some price weakness in the past few weeks).

Jan 1, 1960

By Yun Bai, Sarah Wilson, Michael Salcher, Mark Trim

Over the last decade more than 62 miles (100 km) of civil transport tunnels were constructed in Sydney, Australia, using the sequential excavation method (SEM). The WestConnex motorway tunnels, each stage of which used over 20 roadheaders to excavate up to 40 tunnel headings, had numerous caverns up to 100 feet (30 m) wide and 82 feet (25 m) high. SEM tunnels in North America typically have far fewer active headings. This paper examines the differences in scope and risk allocation for construction phase services, including comparison of the Permit to Tunnel (PTT) process in Australia and the Required Excavation and Support process in North America.

Jun 23, 2024

By Marlies Grimmer, Frank Amo Boateng

One of the challenges of mining is the concentration of heavy metals it releases into the environment through a phenomenon called Acid Mine Drainage. Freiberg is no exception due to its long mining activities. The European Union proposes that all rivers and streams must be in a good ecological status by the year 2027 but this would be difficult for large water sources as it would be economically unviable. Consequently, the approach of treating these waters at point sources would be of immense help and hence this column experiment on mine water treatment with carbon sorbents to remove zinc form the Rothschönberger Stolln. For this experiment three resins namely, APTsorb, activated coke, charred fermentation residues (which was produced by the Freiberg University of Mining and Technology) were analyzed through a simple column experiment to determine their sorption capacities. Through their sorption capacity as this experiment seeks to ascertain: we are able to make suggestions scientifically on the best material among the three for the future design of a treatment plant for the RSS. After the experiment whereby a 10 ml peri glass column was used, material A: APTsorb showed the least adsorption capacity (0.01 meq/g) and this could be attributed to the fact that the resin works well under pre-determined parameters such as pH and surface area. Material B: Activated coke showed a better sorption capacity (0.53 meq/g) in comparison to the basis value used for this experiment. Material C: charred fermentation residue which was produced by the University showed the most efficient capacity of (1.69 meq/g). This in comparison with the value used as the basis for this experiment showed that material C (charred fermentation residue) is very efficient for zinc sorption. pH values measured at the effluent of all the experiment were slightly higher than the pH measured in the initiating water.

Feb 1, 2024

By Zhiguo Chang, QINGXIANG CAI, Ebelia Manda, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, Saleem Raza Chalgri

The concept of mine safety is highlighted in the literature of sustainable mining but not extensively discussed. This study analyzes various aspects of underground and surface mine safety and emphasizes its importance in the context of sustainable mining. More specifically, this research attempts to find the relationship between mine hazards and demographic characteristics, examine and compare the perceptual difference among miners, and determine the impact of mine hazards on workplace safety and safety climate. Descriptive analysis, chi-square test, independent samples t test, and linear regression modeling were conducted to achieve study objectives. Results confirmed that mine hazards were significantly associated with age and experience. Miners perceived lower levels of management safety practices, followed by supervisor safety, coworker safety, and job safety. The analysis showed that underground miners reported lower safety scores than surface miners. There was a statistically significant difference between miners’ perception of safety climate (p < 0.05). The results showed that the higher prevalence of mine hazards predicts poor workplace safety and a low safety climate. The regression models revealed that mine hazards have a significant effect on workplace safety (p < 0.05) and safety climate (p < 0.05). In conclusion, the distinctive model of mine safety presented here contributes to the monitoring and design of comprehensive safety interventions and helps to better understand how certain factors interact on multiple levels to influence the overall safety of the industry. In this study, some suggestions are put forward to provide directions to develop a sustainable mine safety system.

Mar 27, 2020

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Carl E. Bagge

It is easy for a coal spokesman to relate to the theme of this meeting--that the decade of the 1970&apos;s is pivotal for the mineral industries. For the coal operator, this period is crucial. The coal industry, according to most energy forecasters, must gear its production machinery to meet a sharp rise in the demand for coal--in this decade to sustain inevitable boosts in electricity output, and in the next to start supporting a big new domestic synthetic fuels industry that is already in the formative stage. The logic of that projection flows from a combination of hard circumstances--proved reserves of domestic fluid fuels are dwindling, the hope for bountiful and cheap nuclear power must be indefinitely deferred, and the threat of long-term fuel imports to the national interests is becoming starkly visible. Only coal, with its assets of abundance, security and versatility, offers the nation an adequate and immediate lift out of its current energy crisis. A hard-won expansion of coal production made the critical difference between local power load-shedding and major area blackouts in 1970, the year the energy crisis went public. Coal will have to play that same key role, not just through this pivotal decade but through the turn of the century. But the logic of fuel demand apparently does not always extend to supply. The coal industry has had a huge production job laid out for it by the energy statisticians, but up to now the energy policy-makers have not followed through with the aids and inducements that the coal operator urgently needs to do that job well and completely.

Jan 1, 1972

By Frank H. Buchella

Principal factors influencing equipment selection can be grouped into five basic categories. Tonnage Requirements, Ore and Waste Loading, transporting, and ground preparation equipment are largely determined by tonnage requirements. Generally, the greater the tonnage requirements, the larger the equipment size selected. Large size equipment is appropriate for a production of about six million tons (total) per month, medium size for three mil- lion tons, and small size for one million tons or less.

Jan 1, 1973

By D. J. McParland

This paper will deal with some of the considerations which, were involved in the design and construction of the uranium mills in the Elliot Lake area . These plants, eleven in number, range from 1500 to 6500 tons per day milling capacity. Most references are with respect to the seven plants in the Rio Tinto Group which have a combined milling capacity in excess of 20,000 tons per day. In dealing with such abroad subject as mill design, one has the choice, of covering a few specific problems in great detail, or else attempting to cover many subjects superficially and briefly. In preparing this presentation, an attempt has been made to compromise on these extremes, and to select some interesting illustrations which are of general interest in the field of mill design, and of value to persons concerned with mill design broadly, beyond the field of uranium mills.

Jan 1, 1959

By Hernan Fernandez, Khalid Saif F S Al- Khayareen, Volkan Salepciler, Jacek B. Stypulkowski

Wakrah and Wukair Drainage Tunnel, WWDT is 13 km long with a 4.5 m ID sewer water tunnel about 50 to 60 m below ground surface. Integral to the project are several adits with provisions for future connections as well as four work shafts, four intermediate access shafts, ancillary hydraulic structures, and an Odor Control Facility. The shaft depths range from 50 to 60 m. The project is constructed in aggressive ground with aggressive ground water. The construction activities require years of pumping and disposal of the ground water during tunneling operations as well as construction of permanent structures in shafts. Grouting of the corrosive rock mass in corrosive groundwater for the WWDT has been described in detail.

Jun 23, 2024

By Xinghai Lei, Nan Wang, Xiangyang Jin, Yuqi Ren, Yang Li

The upward mining method, as an effective mining method, is widely employed in close-multiple coal seams to extend the service life of coal mines and improve the recovery rate of residual coal resources. However, the upward mining feasibility of the upper coal seam is related to the height of caved zone of interlayer strata after lower coal seam extraction. Therefore, it is extremely important to determine the height of the caved zone after the lower coal seam. The No. 9 coal seam (upper coal seam) and the No. 12- 1 coal seam (lower coal seam) in the Qianjiaying coal mine are selected as the research object. The characteristics of the interlayer strata structure field, fracture field, and subsidence field are studied using UDEC numerical modeling, in which the height of the caved zone is gotten after the No. 12- 1 coal seam extraction. Furthermore, the height of the caved zone is verified by onsite detection of GPR and BTVI. In the numerical modeling, the height of the caved zone is 19.6 m. And the height of caved zone is 14.7 m and 15.4–21.2 m, respectively, by using the onsite detection of GPR and BTVI. The heights of the caved zone onsite detection results are consistent with the numerical modeling result. The No. 9 coal seam is always located above the caved zone after the No. 12- 1 coal seam extraction. Consequently, the upward mining of the No. 9 coal seam is feasible.

Jun 28, 2023

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor -- will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Feb 24, 1997

By Ronald C. W. Webber‑Youngman, Philani Larrance Ngwenyama

Entrapments are a huge risk in underground mines. This happens when miners (or any other persons who have entered underground) survive the initial event of an accident, become trapped or lost in unknown and life-threatening locations after evacuation, and remain unaccounted for. At this point, every second counts, and emergency response is highly desired for any chances of saving survivors. The survival chances of the missing persons depend on how quickly they can be located. Rescue teams are often deployed to search for the missing persons underground. However, the rescue teams are forced to search in random and presumed areas of the mine. This is due to the unavailability of information pertaining to the whereabouts of the missing persons. Not only the provision of accurate locations, but various other types of information such as post-accident two-way communication can enhance the survival chances of the missing persons. This information can be provided by a fit-for-purpose missing person locator system. A wide variety of missing person locator systems are already commercially available, some are in testing phases and others in prototype and development phases. This includes tracking, tracing, location detectors and post-accident two-way communication systems. These systems have unique functionalities, capabilities and limitations; making it difficult for mines to select the most effective, applicable and suitable system specific to their mine. In this study, the user requirements for a fit-for-purpose missing person locator system were developed. The purpose of the user requirements was to provide a guideline to facilitate the system selection process. The user requirements can also be used as a tool to measure and evaluate the performance of the selected missing person locator system. The user requirements were also used to predict the success of the selected system under different missing person incident scenarios. The development of the user requirements showed a potential for many other benefits for missing person locator systems.

Nov 2, 2023