Search Documents

By E. DeLilia

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to in-crease productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: ? Prudent engineering. ? Proper planning. ? Realistic feasibility studies. ? Effective specification. ? Thorough training of the mine personnel.

Jan 1, 1995

By W. C. Hellyer

In an autogenous grinding circuit in which feed at approximately nine inches top size is reduced to a size suitable for subsequent processing, the build- up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge. 9, (1) The buildup of a "critical size" fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large diameter steel balls to the grinding charge. This has certain disadvantages, such as; (i) an increase in mill liner wear; (ii) wear on the steel balls, and; (iii) some loss in flexibility in grinding circuit operations resulting from difficulties in removing the steel balls by means other than by grinding out.

Jan 1, 1970

By Howard W. Adam

Mill length was the primary variable investigated in an autogenous pilot mill circuit. The 5-1/2' diameter mill had both pebble ports and 1/2" wide slotted grates. The plus 1/2" mill product was crushed in a cone crusher and returned to the mill feed along with the minus 1/2" plus 4 or 6 mesh fraction. Tests were run with a short mill, inside length of 26-3/8", or diameter-to-length ratio of 2.50 to 1. The same mill was then lengthened to 48-3/8", diameter-to-length ratio of 1.36 to 1. The effect of mill length on circuit product characteristics was studied. Results show that (1) circuit throughput or grinding rate is lower per foot of mill length in the longer mill, (2) the long mill product is finer than the short mill product, and (3) KWH per ton of circuit product is slightly higher with the longer mill; however, KWH per ton of minus 200 mesh material (finer fraction) produced is essentially the same in the long mill as the short mill, It is not known whether the relationships found for the pilot mill are valid for commercial size mills.

Jan 1, 1973

By P. R. Hervey

Quartz is the second most widely used electronic material, with approximately 3,000 tons of single crystals used each year. Virtually all of this material is synthetic; grown with a technique called hydrothermal growth. We will review the basics of hydrothermal growth, the feedstocks for these crystals, and the challenges to improving the growth process. We will also review the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 1999

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Komatsu is helping to bring mining performance and analytics to the next level.By evaluating underground haulage, a significant component of the room and pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Komatsu is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way.These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer nice to haves, they are must haves.Starting with the best products and the right people is a first step, but then what? How do mines take their operations from average to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way.The fundamentals of operational excellence (OpEx) are based upon the process of define, measure, analyze, improve and control (DMAIC). DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes and then improving the performance and controlling the operation.Komatsu uses OpEx or lean principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety.These same principles can be applied in most situations to streamline processes, improve operations and deliver value."

Jan 12, 2017

By Henry E. Reed

This presentation is about a small company, Industrial Mineral Products, that was formed in 1972 with one product and one customer and by a series of value-added changes avoided disaster and increased sales many times over. The principal of the company stopped by my office in Seattle looking for industrial mineral opportunities in the Northwest. We got together and went through all the minerals in Ladoo's "Industrial Minerals" from Abrasives to Zircon to see if we could find something available on the vast holdings of the Burlington Northern. At that time one of our lessees was operating a silica sand mine near Ravensdale, Washington and indicated that he might be interested in selling out. This sounded interesting to my client and within two weeks the transaction was completed.

Jan 1, 1990

By Rudrajit Mitra, Erik Hulthen, AARTI SORENSEN, TOBIAS HARTMANN, ELISABETH CLAUSEN

There has been an ongoing debate on how to transform engineering education to better prepare students for today’s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into the engineering curriculum, there has been little attention on mining engineering with respect to adopting this approach. This paper addresses the possibilities of integrating entrepreneurship education into mining engineering programs in order to foster discussion among academics from mining engineering on how to infuse value-creation experiences across the curriculum on a course, program and departmental level.

Sep 1, 2022

By S. R. Stine

The Cyprus Thompson Creek Mine is located at 2,286m (7500 feet) elevation in the Central Idaho mountains, 61.16 kilometers (38 miles) southwest of Challis, Idaho off State Highway 75. The Thompson Creek molybdenum deposit lies near the eastern border of the late Cretaceous Idaho Batholith within a complexly deformed sequence of Paleozoic sedimentary rocks. Molybdenum mineralization is contained in a composite biotite granodiorite-quartz monzonite stock considered to be genetically related to the Idaho Batholith intrusive event. The ore is being mined by open pit methods and delivered to the concentrator stockpile with an overland conveyor belt system. The concentrator is designed as a 22,680 metric tons (25,000 ton) per day plant at an average head grade of 0.1% Molybdenum.

Jan 1, 1986

By Harrison H. Roberts

A. We are aware that many who are in the audience have perhaps heard before some of the material which will be presented. Since our firm is more closely associated with the heavy construction industry our experience is more oriented in that direction. Notwithstanding this, the subject your program committee has asked us to present centers mainly in the earth-moving field. We find a common denominator between say, the stripping of a site to uncover an ore-body which will be developed by open-pit methods, and that of excavating & transporting materials for an embankment dam, airport or other project. Both are earth-moving problems and we offer for your consideration a means of determining the most favorable method, equipment selection and resultant cost. We do considerable studies involving rock excavation for tunnels, underground powerhouses, inclined and vertical shafts for penstocks, muck-removal, electrical cable & other related underground work. Hence, we believe we speak the same language.

Jan 1, 1972

By E. M. Frizzell

An ongoing research program at the Spokane Research Center of the U.S. Bureau of Mines is directed toward investigating drilling parameters (thrust, torque, penetration rate, and drill revolutions) during the drilling of roof bolt holes. A system that measures these drilling parameters calculates the specific energy of drilling, and determines drill bit position has been developed by the Bureau and mounted on a roof bolting/drilling machine, through the use of a microcomputer, critical drilling parameters can be immediately interpreted and analyzed. This makes it possible to inform the operator of hazardous roof conditions. Initial results of this program are presented here.

Jan 1, 1990

By C. Jardine

The concept of the system is to minimize costly unscheduled breakdowns of equipment by replacing components earlier than their "life" expectancy. Periodic unit services are scheduled according to pre-set constraints. Service sheets are generated by matching a job and component master listing based on assigned cyclic component lives. The system can provide accountability of all man-hours reported and history information can be selectively retrieved. By reducing unscheduled equipment shutdowns, this system allows for better utilization of manpower and an overall improvement in equipment reliability and availability.

Jan 1, 1979

By T. Arthur Palm, Stephen L. Bessinger

San Juan Coal Co. (SJCC) operates an underground coal mine near Farmington, NM. Continuous miners and a longwall produce 6.3 to 7.2 Mt/a (7 million to 8 million stpy). SJCC is owned and operated by BHP Billiton. The coal seam at SJCC has been shown to have a propensity for spontaneous combustion. As such, during the feasibility study for this project, it was elected to use a bleederless ventilation system on the longwall. Due to the combination of spontaneous combustion, methane liberation and, to a lesser extent, hydrogen sulfide, a typical wraparound ventilation system would not be appropriate. Three-entry gate roads are developed, and the longwall gob is sealed as mining progresses. SJCC uses a nitrogen injection system to continuously inertize the gob.

Jan 1, 2007

By K. W. Grubaugh

The recently enacted federal surface mine law (P.L. 95-87) will increase further the complexity of securing a reclamation permit. This law intensifies the need to present the required reclamation plan in a thorough and comprehensive manner. One plan format, that used in construction performance contracts, offers promise of filling this need. Reasons for using the format of expressed, bilateral, negotiated contracts common to the contruction industry, and the salient aspects of an application which uses this format are reviewed. Advantages of this procedure are seen to be improved mine planning, awareness of the total design job, potential for improved speed of permit acceptance and improved cost control.

Jan 1, 1978

By R. L. Kloberdanz

Peruvian legislation requires the preparation of an Environmental Impact Study (EIS) for new and expanding mines/beneficiation facilities and the preparation and implementation of an Environmental Adjustment and Management Program (PAMA) to control and mitigate environmental impacts associated with existing mining/beneficiation activities. Shepherd Miller, Inc., developed guidance documents for preparing an EIS and PAMA for Peru's Ministry of Energy and Mines and presented workshops to Peru's mining industry on preparing an EIS and PAMA. This paper discusses the process and approach taken and the results.

Jan 1, 1998

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical when responding to a fire incident, as an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring fire contaminants, such as toxic gases and smoke, unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been developed by researchers and scholars around the world. However, those proposed methods rely heavily on a vast number of mine ventilation simulations, which is time-consuming and computer-resource intensive, especially for a large-scale mine ventilation network. In this study, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation is developed and implemented into the MFIRE mine fire simulation software. The results from the derivative method were verified against the results from a traditional method. The derivative method is proved to be reliable and accurate.

Dec 1, 2022

By K. S. Whiting

Elevated concentrations of copper, cobalt, and arsenic within the Panther Creek Basin sediments in north central Idaho prompted an evaluation of the sources of the metals. Potential tailings and waste rock source samples collected at the head of Blackbird Creek were compared to sediment samples in the Panther Creek Basin using electron microprobe techniques. The mineral types, degree of alteration, and the morphology of the metal-bearing sediment grains within Blackbird and Panther Creeks were found to consist of copper-, cobalt-, and arsenic-bearing sulfide minerals.

Jan 1, 1997

By Lawrence Lien

The reduced need for traditionally trained and educated personnel in the mining industry is systemic to the changing mining industry. Universities and other training institutions are meeting the traditional skill needs required by the industry, but are the skill needs going to be the same in the near future? The answer may be no. Mining is changing because of increased liabilities and costs of environmental and safety is-sues; lower grades of minerals in traditional mining activities and the advent of new bio-chemical processes and robotic equipment. More productive and economic alternatives, and larger, more sophisticated and automatic equipment, are also changing the industry. Engineering is more specific, accurate, precise and expensive. Measurement is more thorough and timely of progress, production, costs and productivity. And, the industry will likely be engaging in more undersea mining, possibly space-based processing, less human interaction and more remote control of events than was previously thought possible.

Jan 1, 2011

By J. E. Lowe

The unique application of a large walking dragline in the mountains of southern West Virginia was developed and implemented by Hobet Mining, Inc. Hobet is an independent operating subsidiary of Ashland Coal and is headquartered at the No. 21 Mine in Boone County, West Virginia, near Danville. Hobet also operates the 07 Mine located in Logan County, West Virginia, near Holden. Both mines are similar in equipment and manpower used; both produce over 2,000,000 tons of clean coal annually. Each site encompasses large, contiguous properties with access to rail service. The larger of the two is the Boone County property; it totals nearly 40,000 acres and has ample reserves. In 1977, Hobet was in the process of constructing a preparation plant (Beth Station) at its 21 Mine site with a capacity for two million tons. One of the first orders of business was to design a mine plan that would provide production for the capacity of the plant. Coal production would come from a more than adequate reserve base using the most economical mining methods available. Hobet looked at different deep and surface mining methods to use in order to develop the property; ultimately, it was determined that the mountaintop removal method with the use of a large dragline was the most economical way to develop reserve. Prior to this time surface mining in mountainous Southern West Virginia was generally done by contour mining and/or augering techniques.

Jan 1, 1993

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

By Peter B. Knuckey

1, Introduction Location Kalengwa mine is located in the North Western Province of Zambia, 402 kilometre by unpaved road to the west of Kitwe, which is roughly in the centre of the Zambian Copperbelt, well known as one of the world's centres of copper mining. Its position is illustrated on the map of Africa in Figure 1 and on the map of Zambia in Figure 2. It is a mine of Roan Consolidated Mines Limited whose other properties, Mufulira, Luanshya, Chambishi and Chibuluma Mines, are all located on the Copperbelt. It is managed by the Chibuluma Division of the company. The rate of production from Kalengwa will vary from 12 000 to 17 000 tonnes of saleable copper a year over the next six years. Kalengwa did not exist as a place until the first prospecting parties and later the mine became established and the early working population was recruited entirely from small villages in the surrounding area as much as thirty miles away. The mining area consists of fourteen mining locations amounting to 3.35 square kilometres and the land may be used for any purpose connected with mining, including housing, wood cutting and other utilities. The whole area is, except for minor undulations, a fairly flat plateau with main rivers running from north to south and flood basins known as "dambos" located in a general east west direction. Vegetation is, with the exception of the grassy dambos, temperate forest with relatively light undergrowth. Game of great variety is prolific, as is the associated tsetse fly.

Jan 1, 1971