Search Documents

By J. L. Carr

On average, one to two fatalities occur every year when a miner is struck or pinned by a continuous mining machine (CMM). Proximity detection systems offer an effective means to prevent these types of injuries and fatalities by sensing the presence of a miner and automatically disabling machine motion. The Mine Safety and Health Administration (MSHA) is expected to finalize a regulation that would require the use of proximity detection systems on all CMMs. Approximately one-fourth of all CMMs in use in the United States are already equipped with such a system. The use of these systems will save lives, not only by automatically preventing accidents but also by acting as a tool for educating miners and reinforcing safe work practices. Researchers at the Office of Mine Safety and Health Research (OMSHR) have conducted a series of field evaluations to quantify the performance of these systems in an underground coal environment. These field evaluations measured the distance at which the warning and stop zones were activated. The technology provided consistent activation of the warning and stop zones under many of the conditions tested. However, some performance inconsistencies were observed which present opportunities to improve the reliability of proximity detection system technology. Some of the notable variables that caused significant changes in performance and should be considered in the design, implementation, and use of proximity detection systems include interaction with the trailing cable, performance changes during tramming, and orientation of the miner-worn component.

Feb 23, 2014

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By I. Gombköto, G. Földing, G. Mucsi, B. Csoke, J. Faitli, B. Kovács

This paper summarizes the main achievements of our previous project entitled "Development of a technological system producing quality guaranteed fly-ash based binder". Furthermore, this study deals with the laboratory experience of lignite fly ash utilization for two different goals. On the one hand the fly ash was tested as a binder; on the other hand it was investigated as an underground mine backfill material. Considering the first goal, the utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of relationship between the degree of activation of fly ash and the strength of the obtained concrete. The results confirmed that this hydraulic binder is suitable for construction of stabilization and capping layers or base layer. Regarding the backfilling application, this paper presents laboratory experiments, their results including settling tests, hydraulic permeability and strength measurements and dense slurry technology related results.

Jan 1, 2011

By Steven Keim, Steven Stansfield, Kevin Andrews

Geotechnical, geological, and hydrogeological fieldwork and data collection for the mining industry is often conducted by younger, less-experienced staff members. In many cases, fieldwork personnel are recent college graduates or are otherwise relatively new to the mining industry. Due to busy schedules, staffing shortages, project budgets, and in some cases, poor management, new fieldwork hires often do not receive thorough training. In the past and the present, many workers in the mining industry learn(ed) by “doing.” While this is still considered to be the most practical approach and the easiest way for a company to determine the skill set of an employee, there is always some risk involved in the “feet to the fire” method. The reality is that field personnel are often collecting data on which major operational decisions will be made or on which regulators will base enforcement decisions. Inadequately trained or inexperienced field personnel may collect inaccurate data or fail to recognize key conditions that may influence decisions made by regulators, design engineers, mine managers, and corporate leaders. Even the best engineers may come to incorrect conclusions if they are starting with poor input data. Decisions based on inaccurate data often result in delays, budget issues, unsafe conditions, or even worse consequences. This paper provides numerous mining industry examples of incidences where inaccurately collected field information did, or could have, resulted in major adverse consequences. The paper also offers some simple approaches to minimizing the potential for such problems.

Jul 1, 2023

By A. D. Davis

The Gilt Edge Superfund Site is a former heap-leach gold mine that currently is being remediated in the Black Hills of South Dakota. Mine runoff water is treated before release from the site. The field pH, before treatment, is about 3, and the water contains arsenic and some heavy metals, in addition to sulfate concentrations of about 1400 to 1500 mg/L. In the Keystone area of the Black Hills, naturally occurring arsenic has been detected in ground-water samples from wells. Keystone City Well #4, which is not used currently, showed arsenic concentrations of 36 parts per billion (ppb) and sulfate concentrations of about 19 mg/L. With field samples of water from these sites, a limestone-based method was successful in reducing arsenic and heavy metals concentrations. The results are significant because previous research with the limestone-based method mainly had involved samples prepared with distilled water in the laboratory, in which interference of other ions such as sulfate did not occur. The research indicates the potential for broader field applications of the limestone-based removal method.

Jan 1, 2011

By Rongdong Deng

A tower-like magnetic system comprising eight permanent magnets was installed at the center of a flotation column to separate chalcopyrite and pyrrhotite minerals. A cyclonic flotation was installed within the underpart of the column to separate the pyrrhotite from the gangues. A three-product magnetic flotation column was fabricated to create a magnetic field and a cyclonic zone. The products were Cu concentrates, pyrrhotite concentrates and tailings. The theoretical magnetic field strengths and the magnetic forces were calculated. The results of the flotation experiments showed that the Cu grade increased from 14.20% without the magnetic field to 26.40% in the presence of the magnetic field and that the S grade in the pyrrhotite concentrates increased in the presence of cyclonic flotation. The separation efficiency of this magnetic flotation column was evident. Therefore, this three-product magnetic flotation column may have a potential application, due to its high separation efficiency.

By Jed Greenwood, Lyall Workman, Michael Haggerty, Russell Sheets

Draglines often work from a position on the active highwall or spoil side bench to remove undisturbed waste material and spoil in the previously mined pit. To protect the dragline crew members and the machine, it is necessary that the highwall remain stable while the dragline is present on the bench. In the past several years, we have been involved in determining the causes for highwall failures that included the dragline. While there have been no injuries and limited dragline damage with these incidents, the potential certainly exists for a more serious outcome. In all cases, the operation had completed a geotechnical study to support the ground control plan and pit designs. However, all these incidents included aspects that would not likely have been identified in studies to determine highwall and spoil designs to support ground control procedures. In general, these events included aspects that were localized and would have been difficult to identify in initial slope stability studies either observationally or during the soil testing and modelling efforts. Although the authors do not have quantitative evidence of this, it does seem there has been an increased number of events in recent years. This may be due to loss of institutional knowledge, mining in more challenging areas, or simply an increase in localized variation. This paper will describe some of the issues we have seen and what the causes of failure were. It becomes clear that avoiding similar incidents in the future requires on-going observation and inspection of active highwalls and spoil benches to try and identify local variability and impact on mining. The information can proactively be used to update stability modeling of any concerning issues to determine likelihood of problems and to develop solutions.

Feb 1, 2025

By N. Iverson, E. Haft, V. T. McLemore, M. Woodard, E. Owen

Present and emerging technologies are renewing interest in domestic rare earth elements (REE) production. REE deposits throughout the North American Cordilleran alkaline-igneous belt are being re-examined for their economic potential. In New Mexico, the mineral deposits found in this belt are associated with Eocene–Oligocene alkaline to calc-alkaline igneous rocks. Four areas in New Mexico have been examined for their REE potential. The chondrite-normalized REE patterns are similar for all four districts, even though different REE minerals are found. Crandallite, xenotime, bastnäsite and brookite are found in fluorite veins and carbonatites at Laughlin Peak. Bastnäsite was extracted during fluorite processing from 1954-1980 from the Gallinas Mountains, where samples as high as 8% total REE are found in fluorite veins. Other REE minerals include agardite, parasite, xenotime, and monazite. Allanite, thorite and as much as 8133 ppm total REE are found in fluorite veins in the Capitan Mountains. In the Cornudas Mountains, exploration along the outer edge of the Wind Mountain nepheline syenite laccolith and within phonolite dikes, plugs, skarns and carbonate-replacement deposits in Chess Draw contain as much as 3110 ppm TREE, hosted in eudialyte, monazite, bastnäsite, and calciocatapleiite.

Feb 1, 2023

By Anthony W. Garson

Good morning, ladies and gentlemen: It is a pleasure to be here this morning as a representative of Dean Witter Reynolds; one of the foremost international investment firms in North America. My colleague, Hugh Wilmer (who will be speaking to you a little later), and I are involved as research analysts in the research and writing of published reports containing recommendations on the buying or selling of North American and South African gold and silver mining shares. Our talk this morning will focus on the gold mining operating costs of North American and South African gold producers. However, I am not going to bore you with reams of statistics on the operating costs of large numbers of gold mining operations; how meaningful would this data be to you? Instead, I will discuss what the investor should look for, and how he should use this knowledge in making his investment decision.

Jan 1, 1984

By Barry R. Doyle, Emma C. Ross

This paper presents a 20-year global account of tunneling in gassy ground demonstrating high probability of schedule delays, cost overruns, worker injuries and fatalities. Causes of these failures are systemic. Gas is seldom characterized in terms relevant to design of effective ventilation systems. Control measures deployed in tunnels are often based on outdated industrial safety codes. A change in approach is needed. This paper describes how to perform a desk study to determine if field investigation for gas is warranted, and lists the content of an effective characterization of gas in a geotechnical report.

Dec 1, 2022

By R. L. Howell, L. C. Atkinson

Typical sedimentary sequences overlying coal seams consist of interbedded sandstones, siltstones, shales, and rider coal seams. In many surface coalmine settings, these sediments are saturated; and prior dewatering of them is necessary for effective and economic mining, including the stacking of saturated spoils. Such sedimentary sections usually have a very low vertical hydraulic conductivity that does not allow them to drain in a timely manner prior to their being stripped. One potential solution is installation of drainwells. Drainwells are small diameter wells that can collect water laterally from the various more permeable layers in the overburden and then gravity drain it to a lower layer – often the coal seam being mined – where it can be removed by pumping wells or sumps located in the bottom of the pit. A ground-water flow model utilizing the 3-dimensional finite element code MINEDW has been used to evaluate the effectiveness of usingdrainwells in a hydrogeologic setting that is typical of the Powder River Basin. A series of numerical simulations were completed using various combinations and spacings of drainwells and pumping wells to dewater the overburden and coal seams. The numerical simulations suggest that drainwells can be a very effective method of overburden dewatering.

Jan 1, 2000

By Roe-Hoan Yoon, Kaiwu Huang

Derjaguin and Dukhin [1] were the first to develop a first-principle flotation model by considering the role of surface forces in bubble-particle interactions. According to the model, the ζ-potentials of particles constitute the energy barriers, E12, for particle (1)-bubble (2) interactions, which corroborates well with the observation that flotation recoveries reach maxima under conditions of zero-zeta potentials. In the present work, a series of surface force measurements were conducted for the quartz-dodecylamine hydrochloride (DAH) flotation system, for which detailed studies had been conducted by D.W. Fuerstenau [2], including the measurements of zeta-potentials, contact angles and collector adsorption as a function of pH.

By Larry S. Diaz

It is felt that prior to the presentation of the technical portion of this paper, some general information would be of interest. The Sar Cheshmeh Copper Mining Company was founded by the Iranian Government to oversee the design and construction of Iran's first copper smelter complex, which will be another step in the industrialization of Iran. Since this is the first such plant in Iran, Sar Cheshmeh wisely chose to enlist the technical assistance needed in regard to the facilities requiring engineering and operating know-how from outside of Iran. To obtain the foregoing, SCCM signed a contract with Anaconda-Iran, Inc., which was formed by The Anaconda Company for this project. The general scope of this contract covers the overseeing of engineering and design by Parsons-Jurden as well as physical plant construction. In addition to this, the same services were given to water supply and tailings disposal systems which were not included as part of the Parsons-Jurden contract. Anaconda-Iran is also assisting SCCM in setting up a training program for Iranian personnel for plant operations, administration, etc., which .will go on for some time after the plant startup, under the guidance of Anaconda-Iran expatriates. SCCM?s other responsibilities, in respect to the development of this industrial effort, are the building of a townsite for approximately 2200 families, the expected manning requirements, having all the facilities necessary to provide a pleasant life in a remote area. It has been estimated that the manpower for operations will be 2050.

Jan 1, 1976

By Jaime Adasme, Héctor González, Benjamín Celada

"INTRODUCTION Santiago de Chile is a 7 million inhabitant city which has a 103 Km long subway network operated since 1975 by Metro S.A. This network is used on a daily basis by 2.3 million people. In 2012 Metro S.A. started the biggest enlargement of the network in its history, through the design and construction of the new Line 3 (21.7 Km) and Line 6 (16.5 Km). The detailed engineering contract for civil underground works of Line 6 (L6) was awarded to the Consortium integrated by ZAÑARTU Ingenieros Consultores and GEOCONTROL S.A., in which Geocontrol was in charge of the design of 11 stations and 14.5 Km of tunnel. L6 crosses L3 in Ñuble and Ñuñoa Station, L2 at Franklin Station and ends, intersecting L1, at Los Leones Station as shown in Figure 1. LOS LEONES STATION DESIGN Location and Characteristics Los Leones Station is placed at the North end of the L6, next to the same named station of the L1 and it has four construction units, as is shown in Figure 2: I. Access Shaft (49 m x 47 m). II. Access Gallery (34 m long). III. Station Tunnel (120 m long). IV. Connection Gallery with L1 (104 m long). A singular feature of Los Leones is that the western section of the station tunnel, built from the access gallery, is located below an underground parking lot which is located in Providencia Avenue, as shown in Figure 3. It is important to highlight that the distance between the vault of Los Leones Station Tunnel and the foundations of the underground parking lot is only 6 m."

Jan 1, 2016

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By Roe-Hoan Yoon

INTRODUCTION In 1960, coal accounted for 49% of the world energy consumption, an amount that was reduced to 29% in 1973 because of the availability of cheap oil. At that time, it seemed that oil would remain available for a long time in unlimited quantities. However, this situation changed drastically in 1973/74 when a series of closely spaced price increases from $3 per to $12 per bbl by mid-1974 hit both industrialized and developing countries. Another sharp price increase in 1979/80 to the $34 to $38 per bbl level also hit the world economy hard and, at the same time, set in motion powerful technology development forces for increased coal utilization. At this point, the price of coal was approximately $1.50 per MM Btu, while that of oil approached $6.00 per MM Btu. This huge price differential offered an incentive for developing new coal technologies including liquefaction, gasification, fluidized bed combustion, coal-water mixture (CWM), etc. The CWM technology was of particular interest to the utility industry, which consumes more than 80% of the coal mined in the US for power generation. In this technology, a powdered coal is mixed with water to produce a stable slurry that can be stored for an extended period of time without settling and is readily pumpable. Various reagents in the amount of approximately 1% by weight of the coal are added to inhibit sedimentation during storage and to reduce the viscosity for atomization in burners. The coal loading is in the range of 50 to 80% solids, depending on the particle size and its distribution. With very fine particles, it is difficult to increase the coal loading above 50%, and a binomial distribution helps increase the coal loading. The presence of water consumes a relatively small amount of the heating value of the coal during combustion; for a coal-water slurry containing 30% water, less than 5% of the calorific value of coal is usually consumed due to evaporation. The major advantage of burning coal as a slurry is that many of the oil-burning furnaces can be converted to coal-burning with a minimum retrofit cost. Considering the substantial price margin between coal and oil, the pay- back period for retrofit costs can be relatively short. Nevertheless, the retrofit cost can be further reduced if low-ash coals are used as feedstocks for CWM; there will be savings in the capital cost of installing bag filters or electrostatic precipitators that are designed to remove the ash from the combustion gases. Furthermore, the use of low-ash coals can minimize derating of boilers because the velocity of the combustion gases can be maximized without creating erosion

Jan 1, 1991

By H. Habenicht

Requirements for full extraction in underground coal mining call for inexpensive, safe, techniques to be competitive with conventional methods. Longwall and shortwall systems are to some extent employed for this purpose. Another method would be rib pillar extraction (and pillar extraction). These methods are compared with each other with respect to procedure, equipment, safety, roof control, investment, output, performance, costs The advantages of r.p.e. show this method very attractive. Number and cost of equipment are lowest. Safety and roof control becomes improved by a mobile roof support recently developed in Austria. Its successful use in the R.S.A. is being explained.

Jan 1, 1986

By E. Costa Silva

Among the methods of mineral processing, gravity concentration methods are, probably, those which have lower costs, higher capacities and lower operational complexity. In order to be really effective, these methods require a feed size distribution in which the particles are liberated. Further, there must be a significant difference (usually higher than 1-1.5) among the real densities of the particles. However, in most cases, the traditional gravity concentrators (jigs, shaking tables, spirals and dense medium hydrocyclones) lose efficiency (sharpness of cut and recovery) when the mean diameter of particles are lower than 0.05mm and the difference among densities are smaller than 1. Most gravity concentrators developed in the last 20 years are based on the use of centrifugal forces that create large "apparent gravitational gradient" seeking to overcome the limitations of particles size distribution. This paper presents the experience of the CVRD Research Center in evaluation and development of new process based on using this new generation of gravity concentrators.

Jan 1, 1999

By L. Micale

In May of 1986, the Arizona Legislature passed comprehensive environ-mental legislation called the Environmental Quality Act (the Act). The Act focuses on ground water protection and addresses drinking water quality, aquifer protection standards, requirements to apply technology to reduce discharges, and a state Superfund program.

Jan 1, 1988

By D. L. Langhans

Platinum-group metal (PGM) converter matte from the Stillwater Complex, MT, was subjected to chemical and biological leaching in an effort to upgrade the matte by decreasing the Cu and Ni content. Copper and NL extractions were optimized in a two-stage chemical leach. Atmospheric pressure sulfuric acid leaching removed over 90 pct of the Ni and Fe in the first stage, while 95 to 98 pct of the Cu was removed is the second stage using an acidified cupric chloride leach. This two-stage leach, followed by an elemental sulfur removal step, decreased the weight of the matte by 90 pct. The combined Cu and Ni content was reduced from 65 pct to less than 20 pct, while the PGM content was increased from less than 2 pct to 26 pct. Biological oxidation using Thiobacillus ferrooxidans also proved to be an effective method for removing Cu and Ni. Over 90 pct of the sulfide was oxidized and 99 pct of the Cu and Ni were solubilized, leading to a 60 pct reduction of sample mass during the 17 week bio-oxidation of the Stillwater converter matte. The final residue, after removal of jarosite that accumulated during bio-oxidation, contained less than 3 pct combined Cu and Ni and 6 pct MM.

Jan 1, 1993