Search Documents

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

The evolution of surface mine layout configuration is a function of the schedules and sequence of material excavation within the optimized layouts. The production schedules and sequence of materials movement from multi-bench and multi-face operations are difficult to plan and execute. However, the ability to maximize the profit or net present value of an orebody is largely dependent on the mining schedule. The mining schedule will determine the life of the mine, the projected cashflows, and the investment requirements over the mine life. The pit geometries, pit expansion rates and the periodic volume of materials from different benches in a multi-bench, multi-face open pit mine determine the equipment requirements. The volume of materials excavated, as well as pit layout changes from circular and elliptical geometries of an oil sands mine were modeled using analytical geometric and parabolic partial differential equations (PDEs) and solved within Matlab. The results show that the geometric values are almost the same as those obtained from PDEs for different pit configurations. The economic analysis shows that both the current mining system (CMS) and the cyclic excavator conveyor belt control system (CycEx CBCS) are viable with high NPV (= $3.20 × 1010), PI (> 19%) and IRR (> 29.02%) with short discounted payback periods (= 3.24 months). The CycEx CBCS option is more economic than the CMS option. Its NPV is 1.27 times that of the CMS option. The PI and IRR for the CycEx CBCS option are respectively 2.24 and 1.13 times that of the CMS option. As well, the CycEx CBCS option has almost half the DPBP of the CMS option. The CMS option has an operating cost of $1.386 per tonne ($2.774/barrel) while that of the CycEx CBCS option is $0.779/tonne ($1.558/barrel). These results show that the CycEx CBCS option is the better option for mining companies working on oil sands deposits to invest in.

Jan 1, 2011

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

By Hengwei Yan, Zhanwei Liu, Wenhui Ma, Ping Xiong

The sulfur in high-sulfur bauxite not only pollutes the environment but also harms alumina production. This study investigated the removal of sulfur from high-sulfur bauxite by adding Zn or ZnO during the Bayer process. The results showed that the different valence sulfur (S2−, S2O3 2−, SO3 2−, and SO4 2−) in sodium aluminate solution can be effectively removed by adding Zn during the digestion process. Adding ZnO removes the S2− in liquor, but the other sulfur compounds (S2O3 2−, SO3 2−, and SO4 2−) are not affected. The mechanism of sulfur removal has been elucidated, where the S2O3 2−, SO3 2−, and SO4 2− are first reduced to S2−, and after adding Zn, the S2− enters into red mud in the form of ZnS. The ZnO then reacts with S2− to generate the ZnS that enters into red mud. Thus, this is a new and effective method of sulfur removal by adding Zn during the digestion process. The results shed light on the removal of sulfur from high-sulfur bauxite during alumina production.

Jun 24, 2020

By J. Sattarvand, P. C. Augustine

Despite significant safety improvements, the mining industry remains one of the most hazardous occupations globally and the evacuation of Miners, when an uncontrollable incident occurs in the mine, is the best bet to saving lives. However, Human factors/behaviors during an emergency are likely to influence the evacuation performance. Other industries have made a significant effort to determine these human factors that can impede evacuation performance, however, the current state-of-the-art in mine evacuation or self-rescue is that the evacuation route is predetermined, and a static sign is used to direct miners to the predetermined safe location. This method is limited in representing actual conditions that arise in a real emergency, neglecting the different behaviors displayed by humans. As optimization of the evacuation of a mine plays a fundamental role in emergencies and modeling evacuation behavior and movement of miners is a complex task, this research utilized Agent-Based simulations to simulate the evacuation behavior and performance. It was observed that people with the smart evacuation device made fewer mistakes and arrived at the safe place in less time compared to those have no access to the device. The Mathematical model used in optimizing the shortest path to a safe place is also explained in this paper.

Jun 25, 2023

By A. J. Romeo

The Old Hickory heavy mineral ore body, which lies within the Fall Zone of south central Virginia, has been mined since 1997. There are many differences in this deposit when compared to humate-laden mineral sands mines of southern Georgia and Florida. These differences include an abundance of kaolin-rich clayey sands, highly concentrated and iron-colored heavy mineral sand units, and a base of mineralization that is undulating. For these reasons, the selective approach of dry mining with track excavators is ideal. Grade control in this deposit uses traditional panning techniques and requires an intimate working knowledge of near-by drilling data. Mine geologists train equipment operators to recognize the base of mineralization by such characteristics as a stark color change, significant changes in grain size, and/or considerable, recognizable shifts in the concentration of heavy minerals. The regular pattern of mine site drilling does not always prepare the geologist and digging crews for occurrences of near-vertical contacts between the saprolite basement and the ore sands. These deformed areas, combined with undulating and pinching ore zones, require close monitoring and flexibility by the geologist and the mine operators.

Jan 1, 2005

By W. V. Bluck

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most any given power plant is now going beyond buying at the lowest delivered fuel cost and is now taking into consideration other factors such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1983

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005

By Giuseppe M. Gaspari, Tamara Kondrachova

Contract practices affect cost and schedule of tunneling works, impacting risk allocation between Owners and Contractors. The Authors compiled a dataset of projects constructed in the Toronto Area between 1990–2020 procured either Design-Build or Design-Bid-Build. Data were analyzed identifying independent cost variables across the two methods. Overall industry efficiency further comparison with historical information demonstrates the costs of engineering ongoing escalation due to rising trends in environmental requirements and public consultations stirred through modern communicative platforms. These hard to predict and estimate costs need to be included in the risks evaluated and managed by Owners and not by Contractors

Jun 13, 2021

By A. K. Martin

Adaptive management can be described as a structured, iterative process of robust decision making in the face of uncertainty, with a goal of reducing uncertainty over time through system monitoring. Adaptive management is a tool which can be applied to not only change a system, but learn about the system (Holling, 1978). Adaptive management has been used in ecosystem management for years and guidance is provided in a variety of handbooks and publications. Adaptive management can be applied to industrial facilities and mines through the use of an adaptive environmental management plan (AEMP) and associated practices. The goal of this paper is to provide an explanation of how the plans and practices support regulatory agency approvals and permitting, span the life-cycle of mines, manage uncertainty, and assist in addressing mining impact and legacy issues. AEMPs and associated practices are useful tools to address the uncertainties in identifying, evaluating, and managing impacts of proposed new and modified mining facilities undergoing environmental review. Once a proposed project is approved, the AEMP continues as a living document, being informed, revised, and adapted by the operations. The AEMP can serve as an ongoing management tool for describing and evaluating environmental impacts, continuing in operations into post reclamation. If initiated during planning and environmental review of a project (and in some locations such as the United States [U.S.], the preparation of an Environmental Impact Statement (EIS)), the AEMP becomes a basis to identify, monitor, and manage potential project environmental impacts. Development of an AEMP for an operating mine is also beneficial since there are generally developing and ongoing environmental issues at those facilities as well. Over time, the AEMP is adapted to changing requirements and conditions including those anticipated and unanticipated. Ever increasing scrutiny of mining projects and the complexities of the EIS process highlight the uncertainties inherent in impact predictions. In making the momentous decision of initial project approval, these uncertainties can discourage the regulatory agencies? actions and create stakeholder anxiety and controversy about a project. A well-designed AEMP can support the decision to approve an EIS and enable a project to move forward. Additionally, an AEMP can inform financial assurance estimates and revisions over the life of a mine providing all parties including the citizens of the surrounding communities with greater confidence that potential environmental impacts and risks will be well managed.

Feb 23, 2014

By Walter P. Hansen

Belt conveyors offer a reliable means and often do the most economical job for providing continuous bulk material transport, whenever the terrain permits their installation. The ore processing, construction and mining industries use belt conveyors to carry all types of material, from small to large tonnages. Most of the conveyors Fluor Mining & Metals, Inc. designs for metallurgical plants are in the in-plant category, of limited length and medium tonnages, and use fabric carcass conveyor belting. Belt widths can range from 24 to 60 inches Generally, the layout and design of these belt conveyors present no unusual problems. However, calculations for belt tension and horsepower, design of materials transfers, and the sizings and layouts of belt pulley stations and their drives are time consuming.

Jan 1, 1979

By F. E. Senftle

Preliminary geophysical surveys for nickel deposits are usually carried out by airborne magnetometer and surface electrical methods. Once an anomaly is discovered by these techniques, one must resort to chemistry to identify nickel and determine its concentration. Consequently, a method to determine nickel quickly and quantitatively at the exploration site could help guide detailed sampling and provide analytical data that might otherwise be delayed at distant laboratories. In addition, borehole probes capable of indicating nickel in the rock adjacent to the hole, should prove attractive to the exploration geologist. With these needs in mind, preliminary investigations have been made to demonstrate an in situ analytical technique which appears feasible for nickel exploration. The method depends on the very high energy gamma rays emitted when nickel absorbs a thermal or low energy neutron. These neutron capture gamma rays should be distinguished from the lower energy gamma rays emitted during decay of radioactive nuclides as in conventional activation analysis.

Jan 1, 1971

By Nathaniel Arbiter

The development of flotation machines since the first industrial use of the process can be divided into three stages. The first, up to about 1930, was marked by diversity in the means for contacting floatable mineral with the air/ water interface and for generating the interface, as well as in cell design. By 1927 Taggart (1) could list 170 patents covering flotation cells, and he mentioned dozens which were or had been in operation. He divided cells into eight categories according to design, type of separating interface, and where in the cell and how separation took place. These were: (1) Film or skin flotation with wet or dry oiling of surfaces; (2) pulp body process with bubbles generated chemically by pressure reduction, by vacuum or by boiling; (3) agitation-froth processes involving local supersaturation with air; (4) bubble column; (5) pneumatic; (6) cascade; (7) subaeration; and (8) combination and miscellaneous types and processes. Most widely used then were the agitation-froth, sub- aeration, pneumatic types. By 1943 a significant reduction in categories had occurred to the two main divisions of mechanical and pneumatic cells according to whether agitation and aeration were (a) by an impeller with or without compressed air, or (b) by compressed air alone. Cells at that time were still relatively small; the Morenci Concentrator completed in 1942 used 432 1.7m3 (60 cu ft) Fagergrens for roughing 45,000 and later up to 55,000 t/d.

Jan 1, 1979

By Frank W. Luerssen

Introduction "Austerity" is perhaps an overly generous description of the past three years in the American steel industry. Steel plants operated at an average of only 57% of their capability in 1982-84. The dismal losses for last year are still being totaled. But during the two years before this period, American steelmakers recorded an aggregate net loss of a staggering $6.8 billion. Steelmakers responded by closing numerous marginal facilities. And production capability was cut by 13.6 Mt (15 million st). Capital expenditures still averaged $2 billion annually. But this was inadequate to maintain the existing base of steelmaking facilities. The general economy experienced a satisfactory recovery during this period. American steel, however, continued to suffer from a lagging recovery in the capital goods sector. This was due to record penetration of its domestic market by imports and from very weak realizing prices on the volume that was available. In addition to the direct influx of offshore steel products - which itself depressed prices - the industry also became painfully aware of the growing importance of "indirect" imports. These came in the form of steel-containing producer and consumer durables. Industrial equipment and autos fabricated from foreign steel accounted for the equivalent of 6 Mt (6.5 million st) of lost market opportunity for domestic steel-makers last year. That is over and above the 23.5 Mt (26 million st) of direct steel imports. Given these factors, Inland Steel was not spared from the threeyear downpour of red ink. Despite its record of continuing modernization in steel, our single-plant location in the world's best steel-consuming market, and the high proportion of consumer durables related products, such as cold rolled and coated sheet in our mix, Inland suffered aggregate losses of $277 million during the 1982-84 period. Strategic Planning The foregoing establishes a perspective - a base from which we have restructured our view of the steel industry, and of our own role within that picture. Until possibly two years ago, this present weakness in steel demand was viewed around the world as an aberration, eventually to pass. By contrast, it is now recognized that austere times are the normal steel environment. The topic here is management of resources. This implies an emphasis on strategic planning. It is worthwhile to examine some of the more critical assumptions that were driving strategies among a number of steel companies just before the 1980s. Those projected characteristics of the future steel environment were arrived at through painstaking analysis. They were carefully and heavily quantified and were generally shared by outside observers and our peers within the steel industry. • First, the assumption was made that domestic steel demand would continue to grow at an average rate of 2% per year. • Second, it was assumed that this growth in the American market would continue to be filled predominantly by US mills. It was believed that increases in steel and steel-related demand overseas would absorb much of the ominously growing capacity of third

Jan 6, 1985

By Daniel Brutto

"Environmental considerations are a key driver within marine mining consenting processes across different national and international legislative regimes and are critical in shaping the global public perception of the industry. As a result, it is vital that mining companies seeking to operate within marine environments establish a robust understanding of the sensitivities of the seabed environments in which they are active, the impacts of their activities and the ability of the environment to recover from these impacts. The significant risks of failing to do so include an inability to either obtain or maintain operating permits. At the individual project level, the environmental effects of any given development project are typically defined within the scope of an Environmental Impact Assessment (EIA). For well-established industries operating in well-studied environments this approach typically works well. However, where emerging industries or existing industries that are operating within new environments are concerned, there may be significant knowledge gaps pertaining to our understanding of how specific anthropogenic practices or activities interact with the marine environment. These knowledge gaps can cause significant uncertainties pertaining to the likely significant effects of a project. Such uncertainties may result in barriers to industry and economic progress, increased consenting risks, increased project costs to be borne by individual project developers through the acquisition of additional environmental data during the pre-consent or post-consent project phases, project delays and/or significant increases in environmental monitoring burdens with corresponding increases in project costs."

Sep 1, 2014

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Daniel J. Turk, William R. Banning, John Paterson, Thomas J. Weitz, Michael L. Clark

Introduction Pegasus Gold's Montana Tunnels mine is a large surface gold, silver, lead, and zinc mine located 37 km (23 miles) south of Helena in southwestern Montana. Milling operations commenced in late March 1987. The concentrator achieved full production in May that year after undergo¬ing several modifications and improvements. Production for 1988 is projected to be 2.48 t ,80,000 oz) of gold, 34.2 t (1.1 million oz) of silver, along with 8.5 kt (9400 st) of lead, and 22.6 kt (25,000 st) of zinc from lead and zinc concentrates. Mill throughput currently averages 11.7 kt/d (12,900 stpd), compared to the origi¬nally designed capacity of 11.3 kt/d (12,500 stpd). Cash production costs, net of bypro¬duct revenues for the third quarter 1988, were below $3.20/g ($100 per oz). The introduction of ore to the concen¬trator marked the culmination of 12 years ex¬ploration, evaluation, and development. Initial milling operations encountered diffi¬culties with the circuit as designed. As a result, several modifications and improve¬ments were made to the plant. This article is intended to assist other companies developing projects of this type and complexity. It discusses the mine's de¬velopment from feasibility and construction through start-up. The operation, as it exists today, is reviewed including the modifica¬tions and improvements made since start-up. History The mine is situated in Jefferson County, MT within the historic Corbin-Wickes min¬ing district. Underground mining began in 1864 and flourished until the early 1900s. Between 1864 and 1900 the vein deposits in the district produced about $41 million dol¬lars worth of lead and silver ores containing subordinate amounts of zinc, copper, and gold. At various times, three smelters were operated in the area.

Jan 1, 1989

By David A. Greenhut

The Kubota surface melting system has been under development since 1975. It has found commercial application on the melting of municipal sludge, and ash from solid waste. The melted product has physical properties allowing its use as a substitute for aggregate in cement and asphaltic construction. This paper describes the surface melting system, its current use and anticipated future use.

Jan 1, 1991

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009