Search Documents

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By Richard Komarek

When limestone (Ca03) is calcined in rotary kilns to produce quicklime (CaO), it is not unusual for 10% to 20% of the stone to abrade and emerge from the kiln as quicklime fines (-6.3 mm or -0.25 in.). While there are various industrial processes that can use fines, handling and shipping is tricky and dangerous. Due to the highly caustic nature of quicklime, airborne dust easily bums eyes and skin. On the other hand, money has already been invested in mining (or buying) the raw material and in the equipment and energy needed for calcining. Discarding the fines will not only waste that investment, but add even more cost in transportation and possibly dumping charges. So the question becomes, how can fines best be turned into a revenue-generating asset? Some plants convert leftover quick-lime fines into calcium hydroxide - Ca(OH)2, also known as hydrated or water-slaked lime - for sale into agricultural applications. For farm uses, hydrated lime fines are preferred over quicklime because they are easier to handle. And they are favored over raw limestone fines for their higher concentration of calcium and greater solubil¬ity. From the producer's viewpoint, quicklime fines are ideal for this use because they go through hydration faster than the larger chunks of quicklime. Those larger chunks, or "pebble lime," are more readily salable and more easily handled, for such uses as steel, copper, aluminum and magnesium production, water waste treatment, chemical, paper, glassmaking and flue gas desulfurization in coal- fired boilers.

Jan 1, 1993

By M. A. Reyes, L. Yan

"Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 hours while maintaining an apparent temperature (AT) below 95°F (35°C). NIOSH tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in NIOSH underground coal mine facilities to investigate the thermal environment over a 96-hour period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners increased over the 96-hour test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating heat and humidity temperature profiles for RAs not tested in situ. INTRODUCTION RAs are designed to provide a life-sustaining environment for miners who cannot escape after a mine disaster. One of the major considerations for integrating RAs in mine environments is the thermal environment inside the RA and the impact that the surrounding mine conditions have on the temperature and humidity buildup. Previous research has observed that the metabolic heat of the occupants and the heat released by the CO2 scrubbing systems will cause the RA interior air temperature to increase. In addition to the increase in temperature, an occupant’s respiration and perspiration, as well as the chemical reaction of the scrubbing chemicals with CO2, will contribute to an increase in humidity within the RA. The resulting internal thermal conditions, if not controlled, can subject miners to conditions that can lead to heat exhaustion, heat stroke, or even death depending on the duration and magnitude of exposure. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Mine Safety and Health Administration (MSHA) regulations require that RAs must be designed to ensure that the internal AT does not exceed 95°F (35°C) when the RA is fully occupied."

Jan 1, 2018

By Inkap Choi

Asbestos is a broad term embracing a number of fibrous silicate minerals. These minerals look extremely fragile, yet their fibers have a tensile strength equal to that of piano wire. Chrysotile asbestos is the only mineral that can be woven into cloth, and its fibrous structure is, if anything, even more amazing than its remarkable ability to withstand heat. Because of its unique physical properties asbestos has achieved great industrial importance, and more than 3,000 current uses are known, ranging from use in the kitchen to use in space missiles. Because their minuscule fibers are eminently respirable, asbestos minerals have also found their way into the lungs of humans, where they apparently produce serious biological effects such as asbestosis and lung cancers. 1, 2,3 Because of both their usefulness and their hazardous properties, these minerals have attracted a good deal of attention from research workers during recent years. For example, the surface properties of asbestos minerals have been studied by many investigators. 4, 5, 6, 7, 8, 9 However, even for the important mineral chrysotile, the literature data are more or less conflicting. Pundsack4 measured a PZC (point of zero charge) of 10.1; Martinez and Zucker5 measured 11.8; Chwastiak reports 10.8-11.0; and Raddick measured three sepa-rate apparent PZCls at about pH 8.3, 10.0 and 10.9. More recently Trivedi8 reports 10.11. Naumann and Dresher9 have studied surface charge enhancement of chrysotile by metal ions, and describe how the mineral reacts with contaminantions. In the present paper, the mode of dissolution of magnesium and hydroxyl ion from asbestos minerals placed in water was studied by kinetic experiments involving rate at which these items leave the minerals. Also, some study was made of interaction between dissolved species.

Jan 1, 1972

By G. D. Mainwaring, Weng L. W, Lam Y. K.

The first power transmission cable tunnel in Singapore was the 2.6km long undersea tunnel between Pulau Seraya and mainland Singapore, constructed in the1980s. Ten years later, similar concepts were used for the Tuas Cable Tunnel. The tunnel, which includes a 2.2km long immersed tube section, was designed to accommodate 10power circuits of 400kV and 230kV capacity. It is fully equipped with sophisticated control and communication equipment, fire suppressant and life safety systems plus a maintenance vehicle which runs on tracks through the length of the tunnel. The paper discusses the planning, design, and construction of the Tuas tunnel, and the development of these concepts for future tunnels.

Jan 1, 2001

By Truman P. Stauffer

Secondary use of mined-out space in underground limestone quarries is emerging in the Kansas City area where abandoned quarry sites are being renovated into warehouses, factories, and offices. Mining techniques, ceiling heights, and pillar distribution are being altered as planning for the secondary use of mined-out space is combined with the quarrying process. Even the historic urban- quarry land use conflict invites a reappraisal in that this development provides a potential resolution of the problem. Mutual subsidization by dual rock and space interest is changing the economics of rock production. A city is much more than a surficial adjunct superimposed upon the topography of an area. Its development and growth are deeply rooted in the resources, benefits and problems of its underlying geology. The environmental geologist must address himself to more than the quality of a particular resource. He must comprehensively relate resource extraction and processing with the urban emphasis of optimal use which favors long term usage of land over one time economic ventures. Limestone quarrying, closely allied with the growth of many cities, has commonly left a series of scarred landscapes in the path of the burgeoning metropolis. These abandoned quarry sites are barriers to orderly city growth and fail to serve the people as useful and taxable land. Where quarries are functional, supplying the city with needed growth minerals, problems of blasting damage, noise, and dust exist. Technology faces the challenge of making mineral production and processing good neighbors to the urban market they serve. Continued growth of cities may require more efficient use of space below as well as above the surface optimizing land usage so that long term economic benefits may be reflected in improved mining methods.

Jan 1, 1973

By A. Davis

Pit lake chemistry depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock versus oxidizable sulfide content, and the alkalinity of recharging ground water. In this paper, we assess the geochemistry of 11 existing pit lakes, ranging from the acidic Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington Pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits with the long-term pit lake chemistry lying on a geochemical continuum between end members consisting of influent calcium bicarbonate ground water, and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1996

By Randhir Sehgal

If the primary purpose of a control system is to assure a fixed-quality product at maximum yield, the real issue involved in control of the fine coal cleaning circuit in a plant is to demonstrate that control is technically feasible and economically beneficial . This paper suggests that it is not easy to do so in most cases. Fine coal, defined here as the 28 mesh x 0 fraction of the plant feed, is generally cleaned using a combination of hydrocyclones and flotation. Both of these processes are relatively insensitive to changes in operating variables. Further, the fines fraction general 1 y forms no more than 20% of the plant feed and, at times, is as low as 10%. The instruments to measure flow rates, densities, and product qua1ity (ash, sulfur, etc.) are not sufficiently accurate to allow effective responses to changing state variables and product quality. It is sufficient to run the fine coal circuits at maximum recovery, and the control of product quality and optimization of yield should be achieved by controlling the coarse coal circuits and measuring the quality of the entire clean coal leaving the plant. This contention is made with particular reference to U.S. plants cleaning coal for the utility industry and should be viewed in this context only. It is explicitly admitted that this strategy is mathematically non-optimal in the sense that all size fractions are not necessarily cleaned at equal elementary ash, and would result in a loss of yield. However, under the conditions of conventional coal cleaning practice, this is a sensible approach.

Jan 1, 1988

By Deepak Malhotra, Robert Dorfler

Modern engineering mill design has been refined over the years to the point where detailed ore and process specification criteria can be developed In the engineering design phase of the project. The plant Is then built to the detailed criteria and performance acceptance tested by the owner to see if the as-built mill meets the criteria, This performance testing is critical to the owner; the test must be systematic with sample collection coordinated throughout the plant. Despite the availability of systematic approaches to plant development, the new plants often fall short of design criteria. This paper discusses the key Issues a Project Manager/Process Engineer should Implement to ensure that plants meet design criteria.

Jan 1, 1991

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve's life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young's modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By M. Rice, M. Stanley, J. Marlow

Arizona construction aggregate industry remains in the crosshairs of public debate, caught between the need for aggregate-based building materials and alternative, high-value land-uses. To better manage lands and improve land-use decisions, the Arizona State Land Department has need for a system to assess potential aggregate resources on State Trust lands, and assign dollar values accordingly. Thereafter aggregate values can be compared to residential, commercial, agricultural, recreational, and habitat values -- in a determination of highest and best land-use.

Jan 1, 2002

By John J. Reed

Since the beginnings of, the human struggle for survival and improvement, mining has been one of the basic endeavors of life. Until relatively recent times it was classed as an art. Now we are at work trying to, raise mining to the level of an engineering science where it belongs if we are to prosper. It should be self-evident that this goal can be attained only through industrial progress: based on education and research. It is true that our industry, left to itself, will develop a few new ideas and techniques through the years. However, we mining' engineers are relatively few in number compared to the other disciplines, and the rate of our improvement by such "accidental" discoveries is simply tooslow to keep pace with the rest of our technical civilization. It will be evident in the remarks that follow, that the rapid development of mining education, research, and the industry are extremely interdependent, and will be largely controlled by the amount of cooperation, support, and cross-fertilization that can be developed among all three.

Jan 1, 1961

By John J. Peregoy, James E. Downes

INTRODUCTION The U.S. Department of Energy's Waste Isolation Pilot Plant (WIPP) is being constructed to provide permanent storage of radioactive TRU waste materials emanating from military weapons production. These wastes are contaminated with radioactive elements heavier than uranium, thus the name trans-(or beyond) uranic (Uranium wastes). The WIPP site, which is located 26 miles east of Carlsbad, New Mexico, was chosen thru a selection process after the National Academy of Sciences recommended salt deposits as a promising host strata for the storage of radioactive wastes. Throughout the United States numerous DOE facilities have produced and stored defense-generated TRU wastes. Once WIPP becomes operational in the fall of 1989, all sites may ship directly to this repository. A companion project has developed special shipping containers (TRUPACT) for safe transport of materials to WIPP. The WIPP facility is currently composed of surface buildings, three shafts, and underground storage and experimental rooms and tunnels. Frontier-Kemper Constructors, Inc. (FKCI) has nearly completed the construction of the fourth shaft, an intake shaft, to provide additional ventilation to the underground workings. PLANNED SHAFT EXCAVATION METHOD Full-face raise boring ( upreaming ) was the allowable method selected by Frontier-Kemper Constructors for the excavation of the shaft. After arrival of an oil-field type rotary drill rig in December 1987, a 9 inch diameter pilot hole was drilled from the surface to the mine level, a depth of approximately 2145 feet.

Jan 1, 1989

By T. Y. Yan

O2, NaCl03, H202, NaOCI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meq/g of reducing compounds that consume oxidants in the leaching operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectivity and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1993

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal sup-ports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

Jan 1, 2004

By L. S. Gertsch, M. Z. Abu Bakar

Linear cutting tests of a porous sandstone with a radial drag pick show that saturation of rock with water can increase the specific energy of fragmentation. This appears to be due, in this case, to a saturation-induced increase in the forces acting on the cutting tool without a concomitant increase of the fragmented volume. The mechanisms of this reaction are explored by examining various responses of the parameters controlled and induced during the linear cutting tests, such as cut spacing, cutter penetration, three-dimensional forces and muck production. A program of load-indentation testing is underway to evaluate the permeability threshold of this behavior. These findings are opposite from those made when the same rock is cut with a constant cross-section disc cutter reported elsewhere (Abu Bakar and Gertsch, 2011). Such results highlight the effects of different cutting tool designs, and indicate the need for a well-coordinated program of research to support effective excavator design and selection.

Jan 1, 2012

By James D. Reilly

The time-worn adage "an ounce of prevention is worth a pound of cure" was never more applicable than when used in reference to coal mine safety. Many individuals have dedicated many hours to developing effective accident prevention programs, and much has been accomplished. Each production escalation, however, creates new hazards and safety problems which need special study and research. It is a never ending cyle. To study the progress of coal-mine safety is to raise memories of many individuals who have been dedicated to removing the hazards that have developed with increased productivity and deeper penetration into the earth for coal. Some vivid examples of this dedication are the works of the men who pioneered the use of the safety lamp and the use of rock dust in mining.

Jan 1, 1968

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By J. L. Whitlock

A mutant strain of Pseudomonas paucimobilis is utilized to effectively degrade and or remove 90-98% of cyanide, thiocyanate, toxic heavy metals and ammonia from a cyanidation mill process and mine discharge maximum of 21,000 m3/d (5.5 MGD). Homestake Mining Company?s biological wastewater treatment plant has been in full scale operation for over 2 years at the Homestake Mine in Lead, South Dakota.

Jan 1, 1987