Search Documents

By M. A. Raza

Cable shovels are capital-expensive and primary production equipment in many surface mines. The forces acting on the shovel dipper vary as the dipper moves through the muck-pile. The variations in the forces cause stress loading of the components of shovel and dipper resulting in unplanned downtimes, reduced shovel efficiency, and high mining costs. A potential solution to the above problems is the deployment of an intelligent shovel excavation (ISE) technology, with real-time formation identification, recording, and knowledge transmission capabilities. This research advances the ISE technology by developing dynamic model of cable shovel dipper using Newton-Euler techniques. The model includes the dynamic cutting and dynamic weight forces acting on the dipper as it moves through the muck-pile.

Jan 1, 2011

By Micah Nehring, MEHMET KIZIL, Farzad Sotoudeh, Amin Mousavi, PETER KNIGHTS

Production scheduling in underground mines is one of the most important and complex processes in maximising the economic value of an operation over the life of the mine. Due to increasing energy, transportation, processing and smelting costs and reducing water availability, the extraction of ore deposits through underground operations has become more expensive and challenging. A potential productive and efficient solution to mitigate these issues is to integrate pre-concentration systems into the existing mining system to increase ore grades through a preliminary process of rejecting some waste before sending the ore to the energy intensive mineral processing plant. Further benefit of such systems includes the utilisation of the waste and low-grade material in backfilling of open stopes to reduce the transportation costs and surface environmental impact such as reduction of CO2 emissions and waste transportation. The objective of this paper is to present a new mathematical model to optimise the production schedule of underground metalliferous mining operations in the presence of a pre-concentration system. The proposed model optimises the production schedule and sequencing of stopes within a sublevel stoping operation. The results of this study illustrate the potential economic benefits of using a pre-concentration system prior to a mineral processing operation as a result of increased net present value.

Nov 16, 2023

By W. M. Hart

The remote face loading and entry convergence monitoring systems, employed at some of the Cyprus Amax's underground coal mines, have been able to continuously record changes in face shield resistance across and entry convergence ahead of the longwall face at any moment during longwall mining. The instrumental data obtained from these systems plus in-situ observations during the mining operation can help us better understand the mechanism of overburden strata movement above a longwall face and verify the effectiveness of the current face and entry supports. This paper describes the functions of both the face and entry monitoring systems, and discusses our findings and the issues related to successful ground control for longwall mining.

Jan 1, 1996

By F. Dingwu

The latest technology and novel equipments in kaolin processing industry in China are described in this paper. Some typical experimental results are presented, which include laboratory-, pilot-or commercial-scale tests. The characteristics of kaolin processing technology are summarized, and the developing trends are indicated.

Jan 1, 1995

By D. Bleazard

Barrick Goldstrike Mines, Inc. is actively involved in improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. The identification of equipment failure modes and the development of associated capital asset management practices can minimize failure consequences. Successful programs have included; alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle, resulting in an associated reduction to repair costs and equipment down time.

Jan 1, 1997

By Jan Krason

Introduction The South African Witwatersrand is the world's largest gold-bearing province and gold producing district. But the production capacity of the very big mines (Vaal Reef, Driefontein Cons., Western Holdings, Western Deep Levels, and others) is not as large as that of the Soviet Union's Muruntau gold mine. The Muruntau gold-bearing ore body was discovered in 1956-57, and has been in operation since that time. In the early 1970s, this mine produced 70 to 80 t/a (2.3 to 2.6 million oz per year) of gold. Within the last few years it has become the world's largest producing gold mine. Russian authors do not publish ore reserve or rate of production data. But it is very likely that the Muruntau mining complex, which involves several ore bodies, is currently producing about 143 t/a (4.6 million oz per year) of gold. The author has confirmed this by personal information from several knowledgeable Russian geologists. This amounts to one-half of

Jan 11, 1984

By Rongjie Kong, Shiwei Wang, Dongjiao Gui

Metal cations have significant effects on the flotation of coal and minerals. In this study, the effects of monovalent cations ( Na+ and K+) on the flotation of low-rank coal (LRC) were investigated using flotation and particle–bubble attachment experiments and through X-ray photoelectron spectroscopy (XPS) and molecular dynamics simulations. Oleic acid (OA), methyl linoleate (ML), hexadecyltrimethylammonium chloride (CTAC), ricinoleic acid (RA), and kerosene were used as flotation collectors. The flotation experiments revealed that the flotation yields of LRC improved when OA, ML, RA, CTAC, and kerosene were used in pure deionized water. However, flotation was suppressed for these collectors in the presence of K+ and Na+ ions. In contrast, when using CTAC, the flotation yield increased in the presence of these ions. Specifically, the flotation yield increased from 41.24 to 87.03% when 2.0 kg/t CTAC was used in 10 mmol/L NaCl solution. Particle–bubble adhesion experiments and XPS revealed that the hydrophilic groups of CTAC were adsorbed on the LRC surfaces by electrostatic forces, whereas the oxygen-containing functional groups of OA, ML, and RA formed hydrogen bonds with the LRC surface in pure water. Finally, the simulating result revealed that the hydrophobic ends of the OA, ML, and RA collectors hinder the flotation of LRC by adsorbing monovalent cations, whereas the adsorption of monovalent cations on the hydrophobic end of the cationic surfactant (CTAC) promotes flotation via strong electrostatic interactions.

Jan 31, 2024

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function y(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [ ] where N is the total number of samples, Xi is the sample value at the i - th location, Xi+h is the sample value at the i + h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2, up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any arbitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of one-dimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity.

Jan 11, 1985

By William Gleason

The mining industry is a unique space. It is one in which geologists and chemists can intersect with computer and data science professionals daily. The industry requires expertise in not just mining and metallurgical engineering, but also electrical, mechanical, environmental and more. It requires expertise in worker health and safety, behavioral science, finance and economics, as well as human resources management. The locations of mining operations are often in remote corners, and for underground activities, they are unlike anything else in the world. The industry presents those who join it a wealth of opportunities, but often struggles to overcome incorrect perceptions of safety, labor and environmental standards, making it difficult to recruit and retain employees at a time of increased demand for mined materials.

Dec 1, 2025

By N. Arbiter

Introduction The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter (L/D) ratio. This is in spite of the fact that practice varies substantially: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia, and historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills, on the occurrence of the overload phenomenon, and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape factor is of major importance in this area and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type. Dimensionality in mill design Ball mill shape factors in the period prior to 1927 (Taggart, 1927) averaged 1.1/1 for 29 center discharge mills and 1.0/1 for 30 peripheral discharge mills. With the resumption of new plant construction after the 1930s depression, the Morenci concentrator continued the 1/1 ratio with its 3.1 x 3.1 m (10 x 10 ft) mills. The ratio was increased progressively from then on, reaching 1.6 and 1.8/1 for the largest overflow mills currently. As shown recently (Arbiter, 1989), this is in sharp contrast to autogenous and SAG mill shapes, for which the ratio averages 0.4 in North America. On the other hand, South African practice, starting at the turn of the century with autogenous mills having 4/1 ratios, moved toward 1/1 until recently, when a 2.5/ 1 ratio mill was installed. The reasons given for such divergent practice for mill shape factors are in some respects contradictory and generally inconclusive. The most complete discussion from a practical viewpoint (Dor and Bassarear, 1982) is limited to primary SAG and autogenous mills. Considerations of ball mill dimensionality have had a twofold direction. On the one hand, it has been argued that ball mill efficiencies should increase with increasing diameter and that the specific energy for a particular grind should be reduced accordingly. An inadvertent test of this idea at the Bougainville operation (Burns and Erskine, 1983) resulted in drastic underpowering, which led to failure to reach design capacity until additional mills were installed. This can be taken as strong evidence against any increase in efficiency with diameter. In another direction, it has been argued (Arbiter and Harris, 1982, 1983) that there is a limit to ball mill diameters because of the demonstrable limit to axial flow velocities evident in the overload phenomenon, which as a fact is incontrovertible. But that it places a limit on mill diameters overlooks the evidence given below that appropriate variation in the L/D ratio will permit major increases in diameter, limited only by constructional or economic factors. The present study was directed toward quantifying the overload phenomenon through examination of the influence of mill dimensionality variation and mill operating variables on its occurrence. It is shown that varying the operating conditions, specifically the load fraction and the fraction critical speed, can reduce the risk of overload for existing operations; while appropriate decreases in the L/D ratio can minimize the risk in the design of new circuits. Ball mill overload Ball mill overload is a consequence of the approach to a critical velocity with increasing feed rates or circulating loads. Although the effect has been known for over 50 years, there have been no previous attempts to quantify it. The following description of the ball mill as a flow system is the preliminary to a quantitative analysis: 1) In the absence of a ball load, axial flow of pulp through a mill resembles open channel flow, except for disturbances near the shell due to shell/lifter rotation. 2) For a given ball load (Lf), the void fraction available for pulp hold-up (H) for the ascending portion of the load is approximately 0.4 Lf. In the descending portion, it is greater than this and increases with fraction critical speed (Fc) because of load expansion. 3) Increasing the feed rate increases pulp hold-up and progressively fills the available void space. At a critical flow rate, which depends on system geometry, hydraulic head and pulp rheology, void filling reaches its limit; a pool forms rapidly and fills available space outside the ball load and up to the overflow level. Prior to this, pulp discharges mainly along the ascending rim of the overflow. 4) For a small mill (Lo et al., 1990), it has been shown that with increasing feed rates the critical filling is at or near 50% of the mill volume. Power drops rapidly when this level is reached, as required by the torque formula. 5) The transition to overload is associated with the following phenomena: a) The decrease in power draw. b) Damping of mill sound. c) Reduced comminution of coarser feed sizes, probably due to reduced direct impact in the presence of a pool. d) Increased circulating loads, which further intensify the overload, and increased density of cyclone underflows, which can lead to roping. e) Conditions beyond overload are not known because feed rates are not delibelrately increased beyond this point. f) The existence of the phenomenon limits the capacity of a mill with a fixed set of operating conditions and can prevent the balancing of hard ore feed rate decreases by increases in soft ore rates.

Jan 1, 1992

By F. Khorram

Image processing is a technique that simulates the human vision system. This technique enables applying every statistical or intelligent operation to recognize differences. In this way this new technique is used in quality control systems in most industries. Studying sedimentary rocks is very important from the economic point of view. Some units of sedimentary sequences involve different mineral deposits, hydrocarbon and water resources. Therefore it is important to identify and classify different sedimentary rocks. Descriptive classification of sedimentary rocks is usually based on visual and textural features and chemical composition of a sample. In this paper different samples of a limestone mine in central part of Iran are classified. The samples were collected from different parts of the mine and crushed down in size from 2.58 cm to 3.58 cm. The rock samples were labeled based on percentage of chemical and lithological compositions. Each sample was assigned to one of the distinguished groups. The images of the samples were taken in appropriate environment and processed. A total of 74 features were extracted from the identified rock samples in all images. In order to feature dimensional decrease, principal component analysis method was used. Then Bayesian statistical algorithm was used as a useful tool for classification. Classification Correctness Rate (CCR), calculated for the test data sets are %88, %68, %61 and %72 for the first to fourth class respectively. Therefore it can be inferred that the extracted features of images are appropriate indicators for different samples identification. These precise results besides the advantages of image processing technique, which are increasing speed of operation and decreasing cost, appears to be a desirable success.

Jan 1, 2012

By R. D. Doepker

The dissolution of metals from various metal-mine tailings has been studied through a series of submerged tailings batch tests at U.S. Bureau of Mines laboratories. Tailings selected for this study included both reactive (as determined by column leaching studies) and benign tailings. Metal mobilization in aerated (97 pct saturated with oxygen) samples appeared to be consistently greater than metal dissolution from stagnant (79 pct or 70 pct saturated with oxygen) waters. In the early weeks of the study, sulfate concentrations increased with solid-liquid contact time, while calcium dissolution remained nearly constant. Metal concentrations varied in relation to solid-liquid contact time and aeration. Leachate pH appeared to be nearly independent of solid-liquid contact time for basic tailings. Reactive tailings having both a submerged and a surface component demonstrated increased metal mobility.

Jan 1, 1990

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980

By R. B. Massy-Greene

Project engineering and development is a process of optimisation of capital, operating and financial costs, and extraction rates in the light of current and forecast economic conditions for the sale of the product. The aim of the process is to maximize financial returns to the sponsors (project owners) within many often conflicting constraints. Thus, the sponsor's engineering and financial staff have a common goal, with performance measured in financial terms. Consequently, each group must be aware of, and responsive to, the constraints imposed upon the other. For financial staff, the increasing size and complexity, and escalating capital costs of new ventures have required them to seek finance in larger amounts, and by non-traditional methods. In addition, senior management are requiring indications of the availability of finance as a pre-requisite to a decision to commence project development activities.

Jan 1, 1982

By A. D. Hammond

Until recently, the volumes delivered and unloaded from heap-leaching pads have been estimated by manual methods at Wharf Resources' South Dakota operation. In August 1989, the Engineering Department acquired the MINE-SURVEY software developed by GEM COM Services, Inc. of Vancouver, Canada, as part of a mine planning/grade control software package. The implementation of MINE-SURVEY for pad control resulted in a cost-effective tool to provide accurate and prompt estimates of ore delivered or unloaded from the pads. Volumes can be calculated in a matter of minutes as opposed to hours or days. Another benefit is the ease of comparison of as-build and designed volumes, plotting cross-section in any orientation, importing into AUTOCAD, validation of ore densities and truck factors. This paper describes the application of the MINE-SURVEY systems in heap leaching pad volumetrics.

Jan 1, 1991

By W. G. Prast

Investments in fuel minerals and non-fuel minerals by petroleum companies are not a new phenomena. During the past 25 years, oil firms have entered mining via the acquisition route as well as by the direct development of grassroots mines. In the early 1980s, the "merger mania" in the natural resource industries came to a head. Oil company takeovers of mining firms, as well as other mergers between oil producers, captured headlines repeatedly, and speculation ran wild as to who would next acquire whom. Table 1 summarizes leading mining company mergers in the past two decades. There are some special features to the latest round of minerals investments undertaken by oil companies. First, direct takeovers of mining companies have become the preferred means of entry into minerals, with entry from scratch being relegated to the sidelines. This was not always the case. While there are instances of oil firms buying coal and copper companies dating back to the 1950s and 1960s, most of the early minerals work by petroleum firms was from internally generated projects. When the oil companies first became involved in uranium, for example, the uranium mining industry was in its infancy. There was not much market structure to buy, and it was relatively easy for everyone to get into uranium on the ground floor.

Jan 1, 1983

By K. C. Ko

The pit slope angle dictates the economics as much as the depth of the pit. Steeper slope provides more ore reserves, at the same time, the steeper slope presents higher probability of instability and associated maintenance problems. While large open pit mines mostly belonged to nonferrous metals in the past, other mines are becoming deeper as the mine economics permits deeper mine operations, Such minerals include coal, uranium, phosphate, and others. There are some basic differences between an open pit slope and slopes that are encountered in usual civil engineering work such as dam embankments and highway cuts (Figure 1). The stability of the civil engineering slope changes continuously with time due to ground-water movements, weathering, etc. But the stability of the open pit slope (Figure 2) changes more drastically day-to-day or even hour-to-hour, These changes occur because not only is the slope geometry being continuously changed by the mining operation, but also different geology and geologic structures are being exposed on the slope. Even when a particular slope area is not presently being mined, excavation in adjacent areas can affect the general condition of that slope area. A pit will experience some slope failures during its life.

Jan 1, 1977

By Paul H. Johnson

Resource Engineering and Development, Inc. is designing and building a portable 150 to 225 TPD, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, high-grade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on about 17 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

By A. E. Michon

I am Alfred E. Michon, Vice President- International for Burlington Northern Inc. I work for BN's holding company and my responsibilities include co-ordinating the activities of our eight subsidiary companies as they relate to international commerce--an increasingly important aspect of the overall business of our company. Until last April, I was President of the Fort Worth and Denver and Colorado and Southern railroads, subsidiaries of BN. Prior to that, I headed the marketing and pricing area of BN's coal transportation business. Based on my experience in the energy industry, both domestic and international, I would like to discuss the world-wide trend towards the reliance on low-sulfur coal in lieu of natural gas and oil for the generation of electricity. Since pontification on the energy scene world- wide is best left to consultants with scenario-spitting computers, let me in- stead emphasize this trend through two examples. First I will describe the regulatory and economic factors which have encouraged the replacement of natural gas by low sulfur coal as a boiler fuel in the US. BN's investments in track and equipment were instrumental in this conversion. Secondly, I will show how this same combination of factors has created a large demand for steam coal in the Far East. Again, our company's strategy is to facilitate conversion to coal overseas through timely and sufficient investments.

Jan 1, 1982

By B. Simser, T. Butler

Glencore’s Nickel Rim South Mine, located in Sudbury, Ontario, Canada, is a primary/secondary blasthole operation with ore zones lying between 1,100 and 1,700 m below surface. One of the main benefits of the primary/secondary mining method in high stress ground is that up to 50% of the mining will take place in secondary stopes that should be in a yielded rock mass state. Every future secondary mining stope begins as a primary stope abutment pillar. As with many mines, the stress loading history and rock mass conditions can vary considerably in space and time. Safe mining practices cannot allow for an assumption that the planned secondary stopes are indeed yielded. An incorrect assumption can result in mining development and stoping taking place in high stress ground rather than the expected yielded rock mass conditions. This can result in higher levels of seismicity than expected and incorrect ground support recommendations in areas where workers could be exposed. Seismic monitoring is the mines’ premier tool to track the actual rock mass response to mining. Yielded zones have a reasonably clear seismic signature/pattern over time that is visible in the collected data. The ability to accurately locate small magnitude seismic events can help define and delineate different stages of rock mass failure. The vast majority of the seismic data recorded by the microseismic monitoring system is below moment magnitude (Mw) 0.0. Examples are provided showing how small seismic events (Mw < -1.5) can help provide feedback from the rock mass deformation that allows the ground control engineer to gain a better understanding of how the rock mass is responding to mining processes.

Apr 26, 2022