Search Documents

By M. J. Gula

In the solvent extraction -electrowinning recovery of copper from oxide or sulfide ores there is a continuous transfer of iron and other impurities from the primary leach solution to the copper electrowinning electrolyte via chemical transfer or mechanical entrainment. Iron is the principal impurity that has to be controlled in the electrolyte by a "bleeding" of the electrowinning solution. This bleeding transfers copper and sulfuric acid back to the primary leach circuit along with the iron. Copper is recovered via the solvent extraction process and generally the sulfuric acid is used as a reagent in leaching. Unfortunately, cobalt, which is added to the electrowinning solution to modify the anodic process, is irreversibly lost through the bleeding operation. This cobalt loss represents a significant operating cost to SX-EW copper producers. DiphonixTM ion exchange resin contains diphosphonic acid and sulfonic acid functional groups on a polystyrene-divinyl benzene matrix. This resin has been found to strongly and selectively extract ferric ion from copper sulfate -sulfuric acid solutions containing cobalt. Thus, an ion exchange process using DiphonixTM resin for the control of iron has been developed to replace the conventional bleed stream process. The new process minimizes the loss of cobalt from the electrowinning circuit and strips the iron into a sulfate based solution suitable for leach solution makeup. In addition, this process can effect a lowering of the total iron concentration in the electrolyte circuit with an associated increase in current efficiency. In this paper, data on the loading and elution of iron are presented. Laboratory and pilot scale data will be discussed along with information on process design and comparative economics.

Jan 1, 1996

By David A. Heitman

The Buick Concentrator is a highly automated operation which utilizes a process control system for continuous monitoring and control. The process control system development, installation, and application to the concentrator grinding and flotation circuits are presented in this paper. The design and implementation of analog field sensing instrumentation, a continuous on-stream X-ray analyzer, grinding and classfication circuit controls, and a recent digital process control system utilizing a centralized computer are discussed. Emphasis is placed on the project planning and installation of the digital control system including a presentation of future plans for continuing application of computer control.

Jan 1, 1982

By S. Christiansen, G. R. Winslow, R. W. Kobler

Todays End of Life vehicles are shredded and their metal components recovered and recycled by standard methods. The remaining non-metallic fraction is shredder residue, and contains vast amounts of high value engineering plastics. None are today recovered. Discussed are the developmental approaches used in the first process to recover these valuable plastics. Examined are initial laboratory studies, pilot plant design and construction, product development, results, and flowchart explanations.

Jan 1, 2001

By S. Frimpong

Cable shovels are used for primary excavation in in-situ and/or pre-fragmented formations in surface mining operations. Poorly fragmented hard rock formations and random occurrence of hard boulders in soft formations cause extreme variability of material diggability, resulting in varying shovel stress loading. The stress loading of a shovel’s front-end assembly could result in fatigue failure. Conventional design process, which uses physical shovel simulation studies, is very costly and time consuming for achieving statistically significant results. In this paper, rigid and flexible multi-body dynamic theories are used to develop component stress loading and deformation models of the cable shovel, and solved in the ADAMS/NASTRAN/FLEX environments. Detailed simulation experiments are carried out to examine the performance, reliability, durability and efficiency of the P&H 4100A under varying in-situ formation conditions. The results show areas of high stress fields with a maximum stress of 313.31 MPa at node 441 within the hoist rope. The reliability of the results is confirmed by comparing existing test data. The study is significant because it provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2007

By William Stewart, John Tinkler, Gary B. Hemphill

Of the 345 km long Taiwan High Speed Rail Project, connecting the cities of Taipeiand Kaohsiung, the 23 km alignment on Contract C230 required the construction of5755 m of shallow mined tunnels ranging from 137 m to 1285 m in length. All nine of these tunnels were mined using NATM methodology. On September 6, 2002, a collapse occurred in Tunnel T08 that affected approximately 50 m of tunnel. There was little warning. However, the crew was evacuated approximately 45 minutes prior to failure and thus, no injuries or loss of equipment. This paper will discuss the mining methods, jet grouting ground support, and the instrumentation selected for the rehabilitation and monitoring of the tunnel.

Jan 1, 2005

By C. Leal

Modern production has as goal to reach high and uniform quality in their products. To success with this, it is essential to have a good knowledge of the different variables involved in the process. Investigation or analysis of a process or system has as references the measurements of the variables. These measurements are presented normally in form of data. These data are measured in intervals over time. The aim with measurement of the data in a process is to obtain information about the state of it in order to have it under control. Other goal is to know how the results are affected by the process variables to improve upon product quality, redunding manufacturing cost, better pollution control etc.

Jan 1, 1994

By Weijian Yu, Jianbiao Bai, Jinlin Xin, Shiqiang Xu, Shuai Yan, Zizheng Zhang, Hai Wu

The retained roadway subjected to dynamic loading from thick and hard roof (THF) fracturing caused severe deformations in the thick coal seam (TCS). Understanding the dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF is the first step in determining the stability of the retained roadway. Characteristics of dynamic loading mechanism of gob-side entry retaining (GER) in TCS with THF are investigated through numerical simulation and field test of 150208 haulage gate in Sucun coal mine. To improve the reliability of numerical simulation, the double-yield model is used to simulate gob and the strain-softening model is used to simulate filling body; the dynamic module in FLAC3D is used to simulate the dynamic loading due to the THF fracture, and the global model are validated. Characteristics of surrounding rock convergence, plastic zone distribution, and vertical stress in the filling body after the THF fracture are reveled with respect to width to height ratio (W/H) of the filling body and the dynamic loading strength of the THF. The rational width to height ration of the filling body constructed with high-water materials is 0.57. Field monitoring results show that the GER with THF in Sucun coal mine could adapt the dynamic loading due to the THF fracture and meet the requirement. This study is helpful to better study the stability of GER according to the breaking dynamic load of THF and provides reference and guidance for the analysis of breaking dynamic load of THF under similar geological conditions.

Feb 23, 2023

By Randy Ynchausti

ERIC GUTIERREZ, Knowledgescape: Our next speaker is Randy Ynchausti. He's the director of development, Knowledgescape systems division, of EIMCO Process Equip- ment Company. The title of Randy's talk is "An Expert Control System for Phosphate Beneficiation." RANDY YNCHAUSTI: System integration. How does the systems integrator survive when caught between plant engineers, plant management, and third-party engineering firms, and stay within the budget of the corporate goals? I'm not sure that anyone knows how to do all of that on one project. Results are critical when we talk about how systems integrators work with operating people, how the operating people want systems integrators to work with them, and how both groups work together so that at the end of a project, you have been provided with solutions that meet your needs and solve your problems at a fair price. How does the integrator's role change when working with different types of professionals, such as plant managers, plant engineers, engineering firms, or other system integrators? Finally, what is the dynamics of people working with machines and providing services and solving needs? The average number of employees per pound of copper processed has decreased significantly during the past 15 years. I would dare to generalize and say that the average number of employees per whatever unit of measure we have in whatever industry we work in has decreased over the last 15 years. From a system integrator's perspective, there are some clients who lack a bit of internal expertise as corporate downsizing occurs, and that's one reason why we go out to system integrators or third-party vendors and buy things from them to solve our problems. Downsizing really amounts to savings, but more than that, I think Brian expressed this and I agree with him, it also amounts to a cost. Unfortunately, most of us count the savings and none of us count the cost in that approach. It's easy to count the savings, which is one reason why we count it so quickly. Maybe that also accounts for why we set our pencils down so quickly after we get that dollar value. Maybe we should pick that pencil up every once in awhile and refigure the expense, the cost to us, and determine what we're going to pay during the next year or two or three in losing that expense, or that staff. A broad experience base accumulated over projects at various plants helps system integrators to provide services to clients. This experience enables the system integrator to

Jan 1, 1998

By Antonio Nieto, Jesus Castillo

Research and Development (R&D) departments in the mining sector are essential for creating new solutions on productivity, safety, and sustainability. Nevertheless, the selection of R&D projects is complex, often influenced by subjective judgments and uncertainties. This paper explores the application of the Multicriteria Decision Analysis (MCDA) as a structured approach to evaluate and prioritize innovation projects based on various criteria such as safety, cost, environmental impact, and social acceptability. By assigning weights and quantifying criteria, MCDA enhances decision-making transparency and objectivity. This study aims to show a method that facilitates strategic thinking, resource optimization, and stakeholder engagement, ensuring that selected innovations align with the company’s long-term objectives and commitment to responsible mining practices.

Feb 1, 2025

By Rudolf Voigt

Lignite reserves occur all over the world in different climatic regions. This means, that the impact of the hydrologic regime upon mining activities and, vice versa, of the mining activities upon ground and surface water conditions will be different between any two mines. On the other hand, most economically important lignite deposits can be grouped according to principal depositional and structural features described briefly in the following section. These features do allow a preliminary assessments of the nature of ground water problems which may face the mine. The cost of protection against water which threatens a mine, the environmental impact of the appropriate measures to achieve this end and the restraints of population density which both might exclude the most cost-effective approach will govern the project expenditure for drainage work. Whether or not this expenditure can be borne by the project must be established during the feasi¬bility phases of mine planning. So, the somewhat provoking title of this paper does not mean that its question can be answered once for ever. It should rather serve to bring to the attention of the audience the major features of mine water control.

Jan 1, 1985

By Thomas Jancic

Two of the open-pit, copper-molybdenum mining operations of Duval Corporation are located in the foothills of the Sierrita Mountains approximately 30 miles southwest of Tucson, Arizona. In March 1959, mining from a moderate sized porphyry deposit known as the "Esperanza orebody" was begun at a rate of 10,000 tons of ore per day. Some five years later, a sizeable group of mineral claims west of Esperanza became available to Duval. Earlier exploration and development drilling in this area by others indicated an orebody of greater size but lower tenor than that of Esperanza. A drilling program conducted by Duval not only verified the results of the prior drilling but in addition, revealed a continuation of the mineralization to the south and east. Thus was developed the Sierrita orebody. Open pit design delineated 414 million tons of ore containing an average copper content of 0.35 percent and a molybdenum content of 0.036 percent. In April 1966, the office of Emergency Planning authorized General Services Administration to undertake a program under the Defense Production Act to en¬courage additional domestic production of copper in the interest of national defense. Duval's Sierrita Project was brought to GSA's attention in May 1966 on November 28, 1967, an agreement providing for the development of the Sierrita Property was consummated with GSA. In March 1970, the first copper-molybdenum concentrates were produced in the 72,000 tons-per-day concentrator. Pre-production stripping exceeded the scheduled 105 million tons despite the comparatively short lead time available to equip the mine, build the mine plant facilities, and staff the technical, supervisory, and labor forces. Shortly before the first concentrates were produced, plans were being formulated for a program to increase processing capacity by approximately 15 percent, which entailed increasing overall mining capacity by approximately 50,000 tons per day. This program is scheduled for completion early in 1971.

Jan 1, 1971

By T. L. Heisler

The Cigar Lake project, located in northern Saskatchewan (Figure 1), is one of the world?s largest high grade uranium deposits, with reserves of 150 million kilograms of uranium in a deposit averaging 430 metres below the surface. The Cigar Lake project is being developed by Cigar Lake Mining Corporation (CLMC) which is owned by Cameco Corporation (48.75%), Cogema Canada (36.375%). Idemitsu Uranium Exploration Canada Ltd. (12.875%) and Korea Electric Power (2%). Mining the Cigar Lake orebody is presenting a very real challenge due to the high grade and the ground conditions in and around the orebody. Presently, an underground test of various mining methods is underway.

Jan 1, 1992

By Kent von Maubeuge, Charles R. Landis

The global bentonite industry is a dynamic market balancing a range of end uses with an ever growing number of bentonite producers. In addition, markets in developed countries are elevating the level of detail and transparency for materials reporting in programs, such as the Registration, Evaluation, Authorization and restrictions of Chemicals (REACH) program in the European Union. Bentonite is impacted by programs of this nature. The majority of the bentonite products sold around the world are sodium bentonites. These sodium bentonites consist either of natural sodium bentonites, or naturally occurring bentonite dominated by divalent interlayer cations (Ca+2 andMg+2) subsequently exchanged with sodium cation. The latter variety is often called “sodium-activated“, or “soda-ash treated” bentonite. Once exchanged with sodium, these bentonites are often difficult to distinguish from natural sodium bentonites using common commercial testing protocols. Due to their similar colloidal and bulk chemical properties; the lack of test procedures designed specifically to identify this product feature; and the failure to completely or effectively explain their differences, sodium-activated bentonite is often considered to be identical to natural sodium bentonite in the industry. This article defines both general types of sodium bentonite and presents a technique that could serve the industry as a tool to confirm the variety of sodium bentonite in question. Specifically, geochemical properties such as carbon (C13/C12) and oxygen (O18/O16) isotopic ratios can distinguish activated, even slightly activated bentonites, from bentonites not introduced to additional sodium during manufacture.

Jan 1, 2004

If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always be the first action during the rescue operation. Unfortunately, in many cases, the escape-ways (escape routes) dedicated for miners' evacuation are contaminated with fire byproducts from adjacent entries. The purpose of this paper is to present the ventilation control process that will maintain the escape-way free from contaminants and available for travel. Several scenarios in a different section on ventilation system arrangements are analyzed, discussed and presented. To perform these studies, the author used a mine-fire simulator, which provides a dynamic (in real time) representation of the fire's progress and also gives a display, a color-graphic visualization, of the spread of combustion products throughout the ventilation system. Presented and discussed in this paper, also, are ways in which the mine-fire simulator can be used as a training and teaching tool for miners and, particularly, for ventilation and safety personnel.

Jan 1, 1993

By B. Catalano, D. Ifrim

The Annacis Island Outfall Project includes two TBM bored tunnels with face pressures above 3.5 bar, with an internal diameter of 4.2 metres. This paper discusses the innovative approach to TBM tunnelling and TBM design at the Annacis Outfall Project. The TBM custom design includes a 3.6 m OD core machine manufactured by Herrenknecht and a 5.0 m add-on by the Contractor (Bessac), acting as an extension kit, with optimized gantry design to accommodate for short tunnel drives and quicker launches. This novel design approach produced safety improvement, cost and schedule savings while streamlining logistics of TBM retrieval.

Dec 1, 2022

By Emily Muto

LiDAR technology has made it possible to map large areas of underground mines accurately and rapidly in three dimensions. MSHA Technical Support began implementing LiDAR technology in conjunction with the Agency’s Pillar Collapse Initiative, using scans to determine width-to-height ratios (w/h) of pillars adjacent to mass collapse areas and to conduct risk assessments for global pillar stability in U.S. stone mines. This work quickly expanded to include change detection, such as measuring many pillars to show which are deteriorating over time. Change detection has also been used in ground falls and squeeze areas to see if they have continued to propagate. LiDAR technology supports accurate data acquisition of unstable mining conditions from safe distances. For example, once the LiDAR scan has been processed, it can measure roof fall cavity heights and volumes with the user at a stable ground location. Some LiDAR scanners can collect geologic data, such as joint orientations.

Jun 25, 2024

By Yong Yuan, Wenhao Xiao, Luc Taerwe

"The static shear stiffness of an immersion joint subjected to combined compression and shear forces is investigated by experiments in a test set-up. To explore the performance of the immersion joint, the compression-shear loads, which are applied on a specimen according to test protocol, are determined based on real design situation. In this test, the main focus is on the steel shear keys and the rubber sealing. For the applied loading schemes, different levels of axial force, corresponding to the water depth of the joint, are considered as well as the changing amplitudes of the shear force. The force-displacement curve is obtained and the hysteresis is observed during the whole test. The joint‘s static shear stiffness is calculated, showing to increase linearly with respect to the magnitude of the axial force. Moreover, it is found that the rubber sealing has a significant influence on the shear behavior of the joint. INTRODUCTION An immersion joint is the connecting part between two adjacent elements of an immersed tunnel. Compared to that of the bulk elements, the stiffness of the immersion joint is relatively small. When it is subjected to shear actions, whether resulting from vertical foundation settlement or horizontal earthquake movements, shear-resistance of the joint is the main concern for a safe and reliable water-proof design. A flexible immersion joint, which normally consists of a rubber seal and shear keys installed at an element end is a common solution in practice. The way in which the shear keys and the rubber seal behave in the joint together is of vital importance to a comprehensive understanding of the shear behavior of the joint. However, in literature very few experiments on the shear behavior of immersed joints are available although the flexible joints are applied in practice for more than 50 years already. O. Kiyomiya (2004) carried out both a 3-dimensional experiment and a finite element analysis for a new type of flexible joint referred to as the Crown Seal. The results indicated that this new type of joint can be applied in practice because of the effective reduction of lateral deformation. A linear model was found in the paper of Anastasopoulos et al. (2007) to describe the behavior of the shear keys, which consider that the stiffness of the shear keys tends to infinity. R.S. van Oorsouw (2008) discussed the shear capacity of concrete shear keys in segmental joints, by analyzing the influences of reinforcement and friction force between shear keys."

Jan 1, 2016

By Saurabh Kundu, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Manikanta Nallamilli, Shaik Mahaboob Basha, Neha Gupta, Srinivas Dwarapudi, Dhiraj Madhukar Kadhe

Iron ore pelletizing using compressive and shear action on wet mixture feed has been studied. The physical properties, namely, moisture content, drop strength, green compressive strength (GCS), dry compressive strength (DCS), porosity, and cold crushing strength (CCS), have been studied. Pelletizing tests were carried out on four different types of ore, namely, hematite ore, magnetite ore, goethite ore, and sinter return fines. The inference of shear forces on silica distribution index in dry pellet has been studied using optical and scanning electron microscopy. Significant improvement in physical strength was observed due to compressive and shear forces on the pellet mixture feed. However, decrease in moisture content and ball porosity has been observed. Silica distribution index improved by 1.72 times for hematite ore, 1.47 times for magnetite ore, and 1.68 times for goethite ore. It has been found that bubble cavity has been reduced which is good indicator in terms of physical properties.

Jan 29, 2022

By Laszlo Toth

A feeder is used to control the gravity flow of bulk solids from storage areas, like a bin or a stockpile. For this type of application, it is important to select a proper drive that can fulfill all of the demands put on it. High starting torque capacity, variable speed and the ability to handle frequent starts and stops are some of the demands that the drive must be able to meet. The following is a comparison of the most common type of drives used today for feeder applications. When a feeder is started, the breakaway torque may reach as high as200% of the running torque. The accelerating torque usually is set to protect the carrying element of the feeder, like the belt for the belt feeder and the carrying chain of the apron feeder (Fig. 1).

Jan 1, 2003

By Philip Lindstrom

Retreat mining, using yielding steel friction props, over a seven-year period has been successful at a uranium mine operated by Hecla Mining Company in southeast Utah. The support system allow good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered, Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths.

Jan 1, 1964