Search Documents

By William C. Peters

The frustration encountered by exploration crews in connection with land acquisition could be graphed to show a correlation with the natural law that everything tends to become more so. Figure I shows a rather common, situation. The combinations of ingredients are almost limitless and the resulting brew is often poisonous to an exploration man. A single step, that of taking a series of deep soil samples is often delayed until some sense can be made from "floating" unpatented claims which are obscure in orientation as well as position, placer claims overlapping lode claims, location posts with empty Prince Albert cans, and claims with no apparent assessment work for ten years. Add to this some patented claims with¬out monuments, a state or federal withdrawal area which may or may not invalidate pre-existing claims, a loosely defined tunnel site, and some ranchers who understandably resent the separation of surface rights from mineral rights. The picture is familiar to exploration men. One approach to such problems is to ignore them until someone voices an objection -- but then an even more chaotic situation is likely to develop. Another practice is to stake new claims to cover all ground that is "open" at first glance and then find out if there are conflicts so that the new claims can be adjusted accordingly.

Jan 1, 1970

By J. B. Goddard

Abstract. Leaching of, uranium in situ from sandstone deposits with ammonium carbonate solution containing: dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However because of their high reducing, capacity and their relative abundance, the FeS2 minerals consume; the bulk of the oxidants A pressure leach apparatus was-construtted which permitted the measurement of oxygen consumtion by FeS2. Oxygen consumption by FeS2 is best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1980

By Jose A. Gomez, Javad Sattarvand

Failures of tailings dams have been happening lately. Due to the lack of laws on particular design criteria and stability requirements related monitoring during construction and maintenance, they are thought to be more fragile than hydraulic dams. Monitoring the dam is therefore necessary to understand its current condition and guarantee its safety. The physical condition of the dam could be evaluated with the early identification of seepage. Additionally, due to their adaptability and capacity for high-resolution data collecting, UAVs are an excellent choice for efficiently covering the tailings dam site. UAVs may capture high-quality photos when equipped with a high-resolution RGB camera, thermal sensors, or multispectral sensors. When these sensors are paired with image processing and machine learning algorithms, the result is a reliable estimate of the dam condition.

Jun 25, 2023

Twenty field-scale tests were conducted in a 28 MW pulverized coal power plant in Healy, Alaska, to examine mill power consumption in relation to coal grind size. The intent in this field-scale study was to verify if grind size truly impacted power consumption by a detectable amount. The regression model developed from the data indicates that grind size does impact mill power consumption, with finer grinds consuming significantly more power than coarser grinds. However, other factors such as coal hardness (i.e., the lower the Hardgrove Grindability Index, or the harder the coal, the higher the power consumption) and mill throughput (i.e., the higher the throughput, the higher the power consumption) had to be included before the impact of grind size could be isolated. It was also observed that combining amperage and flow rate into a single parameter, i.e., specific amperage, hurt modeling. Cost analysis based on the regression model indicate a power savings of $19,972 per year if the coal were ground to 50% passing 76 mm rather than the industry standard of 70% passing 76 mm. The study also demonstrated that size reduction constituted a significant portion of the power consumption.

Jan 1, 2008

The administration came on as a strong supporter of the mining industry in April of 1982 when President Reagan delivered his long-awaited minerals policy statement. He promised to reduce America's minerals vulnerability, and called for spending billions on meeting stockpile goals for strategic minerals, opening up federal lands for mineral exploration, elimination of barriers to deep sea mining, and regulatory relief. He defended the favorable tax incentives in the Economic Recovery Act as a stimulus to private research and development that would ensure the availability of materials essential to the nation's economy and national defense. But the administration just didn't seem to get anywhere. Congress, environmentalists, and even foreign governments fought White House-proposed legislation on all fronts, delivering the ultimate coup in forcing Environmental Protection Agency Administrator Anne Burford's resignation and the subsequent EPA staff house cleaning in early 1983. Anti-Reaganites scored victory after victory against Reagan's efforts to stimulate the minerals industry. Congress was stalemated on so many mining-related issues that not much was done either for or against the industry. And the US was not to get its way on the issue of sea mining either. Most of Reagan's mineral policy objectives failed to be met. Three months after the National Materials and Minerals Program Plan was presented and the Cabinet Council on Natural Resources and the Environment was made its coordinator, the head of the Cabinet Council James Watt blamed lack of progress in reviving the mining industry and creating a better strategic stockpile on the weak economy and the House of Representatives, which repeatedly thwarted efforts to open wilderness lands to mining. Congress The 97th Congress spent much of its time saying no in 1982-to the Reagan administration's deep cuts in energy and environment programs, to major changes in clean air and water laws, to oil and gas leasing in wilderness, and to killing the Department of Energy. Most of 1982 (and 1981) was spent in heated budget disputes. Some things that did not happen: • The administration and industry failed to get changes in controls of hazardous air pollutants and sulfur dioxide emissions that are implicated in the phenomenon known as acid rain. Industry had wanted to relax requirements for new industries building in clean air regions where the air act demands prevention of significant deterioration (PSD) of air quality, and to relax requirements tightening up the regulation of emissions of hazardous air pollutants. The air battle is expected to continue on five major fronts-acid rain, hazardous air pollutants, PSD, automobile pollution, and nonattainment. • Regulatory reform legislation to overhaul the way government carries out the law died a slow death last year. Business groups and the administration said federal agencies should be required to consider cost-effective measures of reaching regulatory objectives of protecting public health, safety, and the environment. Opponents, including environmentalists, feared such action would delay, weaken, or scuttle important regulations. • Congress turned thumbs down several times on proposals for oil and gas leasing in wilderness but could not agree on any new wilderness recommendations (see The Wilderness Battle). • Congress refused to open the door to the Reagan administration's plan to raise up to $4 billion a year from sales of federal lands. The administration identified surplus and excess federal lands, mostly obsolete buildings or isolated tracts of land, that could be sold by the General Services Administration (GSA) to help out the federal budget deficit. Congress took no action. Some things that did happen: • Congress extended the Defense Production Act (DPA) for six months through March 1983 without changing the 32-year-old law. That came after it failed to resolve sharp differences over proposals for critical minerals programs. Differences concerned both the amount of funds and the scope of programs that would be authorized under the DPA's Title III. Some proponents pressed for $5 billion in funding for loan guarantees or purchase commitments to spur domestic production of minerals such as cobalt. Other members of Congress wanted smaller amounts of funding, and the Reagan administration, until about November, had opposed any use of federal funds for strategic mineral programs. These measures were certain to come up again before the DPA extension expired in March. • House supporters of the Critical Materials Act of 1982 were unable to come up with the twothirds majority needed to pass the bill, so it died on the House floor in December. The bill proposed that a council be established with responsibility for coordinating federal materials research and development. The administration opposed the council creation contending that the Cabinet Council

Jan 5, 1983

By D. Kimball, P. Chambers

"BACKGROUND In the event of an explosion or fire in an underground mine, workers can be exposed to a deficiency of oxygen, an excess of carbon monoxide, or both. These threats can occur as separate conditions or simultaneously. A lack of oxygen in the breathing air can only be addressed via the use of a self-contained breathing apparatus (SCBA) acting as a source of oxygen. An excess of carbon monoxide can also be addressed via the use of an SCBA, but if the threat occurs in isolation (that is, the atmosphere still contains sufficient oxygen to support life) and the concentration of the threat gas is not extreme (< 2%) then the carbon monoxide threat can also be addressed by the use of a filter self-rescuer (FSR). Used together, the SCBA and FSR offer a far more efficient and universally capable life support system than when used in isolation. However, the SCBA does not take advantage of the fact that the surrounding atmosphere likely contains some level of useable oxygen; i.e., the SCBA always supplies the total required oxygen from its limited supply, resulting in a ceiling on its useful life regardless of the level of oxygen in the surrounding air. To address this technology gap, what is needed is a ""smart"" SCBA that provides filtration and catalytic protection against threat gasses and has an extended duration life-sustaining oxygen inhale stream independent of the threat content and oxygen deficiency of the surrounding atmosphere. DEVELOPMENT Developed under contract with NIOSH the Smart Escape SCBA is comprised of three major components including; 1) oxygen supply, 2) oxygen sensing & dosing electronics and, 3) a CO catalyst and carbon bed broad spectrum FSR. The SCBA is designed as a hybrid system that provides non-toxic breathing air by using an approved Chemical, Biological, Radiological and Nuclear filter self-rescuer and a catalyst to convert high levels of carbon monoxide to harmless carbon dioxide (CBRN FSR/CO). In addition, the Oxygen Sensing & Dosing Electronics (OSDE) package adds sufficient oxygen to make up for deficiencies detected in the ambient air (Figure 1). By making use of the ambient oxygen, less oxygen is required for a one-hour unit life. This means that the Smart Escape SCBA fits in a smaller and lighter package than a similar-duration conventional Self-Contained Self-Rescuers (SCSR). Alternatively, taking advantage of available ambient oxygen could offer a significant increase in working duration in a unit with the same size as current SCSRs. The research performed under this NIOSH contract involved numerous tasks including: (1) definition of performance and system requirements for the Smart Escape SCBA, including keeping environmental stressors within acceptable ranges, providing at least one hour of breathable oxygen supply, and using a mask or hood that allows high-quality voice communication; (2) designing, building, and evaluating prototype units to support extensive bench top testing at Avon Protection and third party labs to demonstrate the device’s capabilities; (3) building sufficient quantity of Smart Escape SCBAs designed to be intrinsically safe (per MSHA criteria); (4) testing and evaluation by the National Personal Protective Technology Laboratory (NPPTL)."

Jan 1, 2015

By Verya Nasri, Jaeseoung Lee, Ashish Bhargava, Shashank Gupta

This paper presents the unique design and construction challenges for the Technoparc Station, located in downtown Montreal as a part of Réseau Express Métropolitain (REM), a light rail rapid transit system. The station is located 15 m below the street with rock-bearing secant pile wall as the primary structural system working as both the retaining and gravity structure. The paper highlights the challenges related to the support of excavation structure, invert slab resisting high hydrostatic forces, waterproofing tightness etc. It also focuses on the importance of Building Information Modeling (BIM) in underground tunneling projects for effective coordination, clash-free, optimized design and costs.

Jun 13, 2021

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By D. Mohapatra

Extraction of Al(III) from aqueous sulfuric acid solutions into organic Cyanex 272®-carbon tetrachloride systems was investigated from a multi-component mixture containing aluminum, cobalt and nickel. Al(III) extraction efficiency was quantitative with 1.0 M Cyanex 272® in two stages at an aqueous: organic (A:O) phase ratio of 1:1 and an equilibrium pH of 3.2. The stripping of Al(III) from the loaded organic (LO) with different acids indicated sulfuric acid to be the best stripping agent. More than 99% stripping of Al(III) from the LO was achieved using 2 M H2SO4 at an A:O phase ratio of 1:1 in a single stage. The stoichiometry of the extracted species of Al(III) was determined by the slope analysis method. The extraction reaction proceeded via the cation exchange mechanism and the extracted species was assumed to be AlA3?3HA, where HA refers to the dimeric and A the anionic form of the extractant, Cyanex 272®. The extraction of Al(III) was studied in the presence of various ions to ascertain the tolerance limit of individual ions.

Jan 1, 2008

Where space is limited, as it is throughout most of the northeastern United States, new construction either takes place high above street level, or below it. In Lower Manhattan, NY both kinds of expansion can be found in abundance. That is good news for the nearly 200 attendees at the George A. Fox Conference, presented by the Underground Construction Association (UCA) of SME at the Graduate Center, City University of New York, on Jan. 30. Among the many projects taking place in Lower Manhattan?s massive trans-formation process, are expansions to the city?s vast underground network of subways and other tunnels. ?New Yorkers either live on the ground or below it,? said keynote speaker Charles J. Maikish while explaining how an attempt to build above street level walkways never caught on in the city. Maikish is the executive director of the Lower Manhattan Construction Command Center. His job is to oversee the $22 billion project that will transform the island by 2010. From the construction of Freedom Tower at the site of the fallen World Trade Center buildings, to the expansion of the Second Avenue Subway, the extension of the East Side Access, No. 7 line, the new trans-Hudson line and numerous waterway tunnel expansions, including City Water Tunnel No. 3, the task Maikish is charged with is a huge one. He is primarily responsible for coordinating the scheduling and staging of the overall rebuilding plan, along with the day-to-day coordination of construction work down-town. He places particular focus on mitigating impacts on the environment and mobility, maintaining and improving access and alleviating congestion of any kind related to construction. At the time of the Fox Conference, there were 59 projects under way in Manhattan. All of those projects need things like concrete and steel delivered to sites in very tight working environments. And some need the equipment in even tighter spaces. ?This is not just about the recovery of Lower Manhat-tan (from the 2001 terrorist attacks) but this is a plan to restore it and to maintain its integrity,? said Maikish. ?I think that is the appropriate response to the terrorist attacks.? When Freedom Tower is completed, it will stand 541 m (1,776 ft) about the skyline. That will be a strong statement to the world about America?s strength. But it is the work that takes place much lower that was of interest to the conference attendees. On this respect, Maikish said Manhattan?s efforts below ground aim to provide relief to the city?s street level congestion and to make sure Manhattan ? already essential to the economy of the United States and the world ? stays current by upgrading the existing telecommunications and technological network while also allowing room for growth in that area.

Jan 1, 2007

By Stanley M. Jarrett

Gentlemen, I am pleased to address this gathering of engineers and operation managers representing a large and important segment of the metal and nonmetallic mining industry. Since you know from the printed program that the theme of my paper is the furthering of safety in open pit mines, perhaps you will have guessed that I will also comment upon the image created in the public mind by the industry&apos;s safety record and the potential consequences thereof in national health and safety legislation. Operators of surface mines have some cause to congratulate themselves on the basis of figures issued by the national safety council which show that lost-time accidents per-million-man-hours in surface mining (11.18), is lower than that of all other mining. Moreover, the accident frequency in surface mining is only slightly above the median accident rate for all American industry (8.87). That is a good record.

Jan 1, 1972

By Monserrat Rebolledo, John L. Uhrie, Candice Simms

Jetti Resources has developed a catalyst which overcomes the passivation of primary sulfides, enhancing the heap leach recovery of copper from chalcopyrite. It is important to emphasize that heap leaching of copper sulfides, whether with or without the Jetti catalyst, is a biooxidative process. We have demonstrated the efficacy of Jetti’s technology in bioreactors, with a chalcopyrite-dominant porphyry ore. In the presence of Jetti’s technology, optimal bioleaching conditions significantly increase copper extraction by 2.6 times that of the baseline.

Feb 1, 2025

The extraction and processing of minerals from surface mines and quarries can produce significant fugitive emissions as a result of site activities such as blasting, unpaved road haulage, loading, primary crushing and stockpiling. Uncontrolled fugitive dust emissions can present serious environmental, health, safety and operational issues impacting both site personnel and the wider community. Simulation technology is finding increasing use for the purposes of advanced warning of potential problem emissions in addition to providing a basis for future planning applications where demonstrable compliance with regulatory requirements are necessary. The initial re-entrainment and subsequent dispersion of fugitive dust presents a process complicated by the combination of the in pit topography, the surrounding natural topography and the dynamic nature of emissions from these sites. These factors impact upon the accuracy and reliability of the conventional Gaussian plume based computational prediction methods employed for regulatory compliance and IPPC applications. This paper proposes that optimal modelling of open pit emissions may be more accurately achieved by the use of a multi-scale predictive modelling approach utilizing computational fluid dynamics (CFD) methods for high resolution near source dispersion and conventional Gaussian based methods for far field dispersion modeling. This paper presents a numerical based flow and dispersion analysis of a typical UK based open pit utilizing CFD in conjunction with a conventional Gaussian plume based methods. Typical operating emissions and meteorological conditions are obtained from long term data records collected at a large operating quarry extraction operation in the UK. Emissions are modelled using a Lagrangian framework within conventional atmospheric boundary layer (ABL) profiles expressed as functions of turbulence and velocity parameters under assumed neutral conditions. Results are presented in terms of the impact of site topography on in pit retention as compared to the Gaussian based method.

Jan 1, 2009

By M. G. Hester

The inadequacy of traditional geostatistical methods for estimating some precious metals deposits has become apparent in the last few years. New methods or estimation such as Indicator, Probability and Multigaussian Kriging are difficult to understand and apply. Case studies using a new method of variogram calculation proposed by Srivastava show the method valuable for variogram estimation in precious metal deposits. Some simple, sometimes unorthodox. estimation methods that have proved useful in Some situations are presented.

Jan 1, 1990

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

This paper proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology. The new parameter was defined as the total strong layer thickness (tstr) that represents the strength and stiffness of the overburden with a single value. Twelve field measurement case studies from 11 different U.S. longwall mines with different overburden geologies were used to develop the new methodology. 2D numerical models of these case studies (and additional parametric runs with different panel widths) were verified against field measurements such as surface subsidence and stress. Statistical analyses using the model results were conducted for a loading model with the new tstr parameter as one of the variables. The new methodology was found to have a coefficient of determination (R2) of 85% when compared to the field measurements and the parametric models. The method was then tested for practical implementation for pillar design. The percentages of load carried by the gob as estimated by the new method were implemented into the LaModel program, that is commonly used in the coal industry. The results obtained from LaModel were compared to the available field stress measurements, and the new method implemented into LaModel was found to give successful results.

Jul 18, 2022

By Yinan Zhang, Yi Luo

The widely used R70 method is modified to measure the self-heating propensity of low-rank coals. This modified R70 method enables the introduction of controlled amount of moist oxygen into the reaction vessel. Three coal lumps were collected from three different locations in a surface mine in the Powder River Basin. The coal samples were tested in oxygen flow with controlled moisture content under adiabatic condition. By measuring the relative humidity at the exhaust exit point of the testing setup, the flux and cumulative wetting heat that is consumed by coal samples can be determined. Through a better way of determining the coal’s specific heat, the total heat, including heat of wetting and coal’s oxidation heat, required to raise coal to a given temperature can be determined. Then, the contribution of heat of wetting at the different stages of the testing is quantified. The effects of evaporative heat through a group of tests have also been quantified. From this research, a better understanding of the effect of wetting heat on inducing low-rank coal’s spontaneous combustion can be acquired.

Nov 30, 2022

By C. S. Todd, R. L. McNearny, S. Dun, P. Clark, P. W. Conrad, X. Liu, J. Q. Wu, H. Rhee, W. J. Elliot

Soil erosion is strongly related to soil hydraulic properties. Understanding how surface coal mining affects these properties is therefore important in developing effective management practices to control erosion during reclamation. To determine the impact of mining activities on soil hydraulic properties, soils from undisturbed areas, areas of roughly graded mine spoil, areas with replaced topsoil before seeding, and revegetated areas at the Rosebud Mine in Eastern Montana were evaluated. Field and laboratory studies were conducted to determine the soil hydraulic properties of the four representative areas, including particle-size distribution, organic matter content and saturated hydraulic conductivity. Using this data, Water Erosion Prediction Project (WEPP) simulations and risk analyses were performed to investigate mining’s effects on changes in soil erosion potential. Significant differences were seen in the hydraulic properties of the soils in the representative areas due to the mining and reclamation practices at the mine. The WEPP simulations show that the potential for soil erosion increases as a result of mining activities disturbing the soil. The simulations also indicate that the erosion potential may return to pre-mining levels over time with effective revegetation practices.

Jan 1, 2015

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By Leslie Burnside

Homestake Mining Co. set out to complete final reclamation at a former open-pit gold mine in west central Nevada. The goal was to exceed regulatory standards by satisfying the company&apos;s own high corporate standards for successful reclamation. Homestake&apos;s completion requirements challenged available technology due to the unsuitability of heap material as a growth medium, the harsh environmental conditions of the site and the region&apos;s lack of native growth medium. Accomplishing these goals required enlisting a multidisciplinary project team to develop, test and implement appropriate and cost-effective revegetation alternatives.

Jan 1, 1999

By Jürgen. F. Brune, CLAIRE STREBINGER, ADITYA JUGANDA, Gregory E. Bogin Jr

The abstract highlights the risk of methane gas explosions in underground coal mines and the potential of computational fluid dynamics (CFD) modeling to simulate such events and assess their impact on mine ventilation. The study focuses on developing CFD models for large-scale explosions in longwall mines, specifically simulating methane gas explosions resulting from face ignition during coal cutting. The research demonstrates the integration of a combustion model into a longwall mine ventilation model and shows how the availability of explosive gas mixtures significantly affects flame propagation and explosion pressure.

Mar 27, 2022