Search Documents

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By S. Hardcastle

Tele-remote operation of production equipment from surface will change the design criteria for underground mines. And for ventilation, with machine operators on surface, conventional planning to dilute and remove pollutants can become redundant. Natural Resources Canada with industrial partners are investigating what will be the new environmental design criteria. Additional complications include new mining equipment being designed without standard services and mines’ desire to eliminate conventional auxiliary ventilation. Findings to date show the cooling of equipment’s hydraulic systems to be the most demanding element, especially in dead-ends and when stationary. Consequently, revised ventilation based heat control strategies for equipment are being developed for the automated mine of the future.

Jan 1, 2001

By Steve Klein

The Transbay Downtown Extension (DTX) in San Francisco involves the construction of a large-span tunnel with a width ranging from 43 to over 60 feet. The tunnel will be excavated using the New Austrian Tunneling Method (NATM), also known as the Sequential Excavation Method (SEM), in highly fractured and sheared rock. This paper discusses the FLAC (Fast Lagrangian Analysis of Continua) analyses that were completed for conceptual design of the tunnel support system and to develop surface settlement estimates for the evaluation of measures to protect existing buildings located above the tunnel from damage.

Jan 1, 2008

By S. Suwansawat, D. J. Maconochie, C. C. Chang

This paper describes the overall delivery of the tunneling for the Mass Rapid Transit Authority of Thailand’s Chaloem Ratchamongkhon Line in Bangkok and the constraints provided by the alignment. Eight earth pressure balance tunnel boring machines were employed under two major civil works contracts to drive approximately33 kilometers of tunnel in soft saturated ground beneath the crowded streets of Bangkok. Responsibility within the contract for building damage provided an inherent control for ground movement arising form tunneling when the right of way was narrower than the influence zone. These limits affect the earth pressure balance requirements and permissible ground loss. The methods adopted to limit ground movements and deal with the various obstacles to tunneling influenced the design and operation of the machines. The challenges provided by the need to tunnel through numerous lines of piled foundations of canal bridges and overpasses crossing the alignment are described.

Jan 1, 2001

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By Luminita Calin

King County (Seattle, WA) is on a monumental task of building the new Brightwater System complete with a new treatment plant, three main conveyance tunnels, a new outfall into Puget Sound and other ancillary works. This paper will describe the first conveyance tunnel, Brightwater East currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor that is scheduled for completion in early 2010. The project located in Bothell, WA (north of Seattle) is in both King and Snohomish Counties. It was the first of the major tunnel projects that was scheduled by King County for the Brightwater System. The East Contract consists of the following major elements: 14,000 ft of 19'-2' EPBTBM mined tunnel using 16'-8' ID bolted, gasketed precast concrete segments for a primary liner; installing and encasing 14,200 ft each of 48', 66', 27', 84' in diameter steel pipes inside the tunnel along with three runs of fiberoptic cable; 2,430 ft of 72' in diameter microtunnel including three caisson shafts and associated structures; one Intercepting Structure (IS) shell to mine from that is 74 ft deep and 74 ft finished in diameter with 130 ft deep slurry diaphragm walls, tremie slab and final concrete wall lining; one Influent Pump Station shell (IPS) 83 ft deep, twin 77 ft inside diameter cells, with 160 ft deep slurry diaphragm walls, tremie slab, and final lining; two short 12 ft in diameter inter-shaft connector tunnels; one extraction shaft 40 ft deep by 40 ft wide and 140 ft long for connection to the new treatment plant piping.

By N. Niemuth

Strong demand for copper in developing nations such as China and India, plus the additional demand for industrial minerals to supply the Arizona construction market, brought about a record-setting year for the state?s mining industry. The value of Arizona?s copper production set a new high of $5.5 billion and pushed the total value of mineral production to $7.58 billion. This was also a record. As it has for many years, Arizona ranked first in nonfuel mineral production in the U.S. In addition to leading the nation in copper, Arizona ranked in the top five in molybdenum, sand and gravel, gemstones, perlite, silver, zeolites and pumice. Generally strong and rising prices, especially toward year?s end, fostered a bullish atmosphere that encouraged significant levels of acquisition and exploration. This activity has spread beyond the normal commodities to include some, such as manganese and fluorspar, that have not been mined in Arizona for decades.

Jan 1, 2008

By Jerry D. Pfarr, Gary Loving, David G. McDowall

Introduction The Open Cut is one of the best known landmarks in South Dakota's Black Hills. It is the site of the original discovery of the Homestake ledge, or lead, in 1876. Between that time and 1945, the Open Cut produced about 36 Mt (40 million st) of gold ore, the majority of which was drawn from underground operations. In 1981, a drilling program was undertaken to determine how much ore the old timers left behind. The results of this study indicated an ore body made up of broken and caved ground, and solid blocks in pillars and crowns. Reserves are estimated at about 6.8 Mt (7.5 million st) of gold ore, grading at 4 g/t (0.116 oz per st). Total tonnage of material, including waste, is estimated at more than 60 Mt (66 million st). The mining plan is a combination open pit and underground operations. The bottom 78 m (255 ft) will be mined by the underground panel-caving method. The open pit was designed as a contractor operation up to the expected milling stage or the point of sustained ore production. The pit was designed to avoid disturbance of US Highway 85 near Lead, SD. In 1983, the South Dakota Board of Minerals and Environment approved the mining and reclamation plan. Test mining began in the north of the Open Cut using open pit methods. Upon completion of the test pit, Homestake Mining's board of directors approved an expanded mine plan. They committed an additional $27.1 million to prestrip the ore body that is expected to yield 23 t (750,000 oz) of gold. Project life is estimated at 15 years. Exploration program In early 1980, 10 diamond drill holes were drilled from the surface in the vicinity of the east side of the Open Cut. The reserves delineated by that drilling were too small to justify their development. A continuation of this study attempted to quantify the tonnage remaining in the bottom of the Open Cut in the crushed remnants of old stope-and-crown pillars. This was originally thought to be minable by improved drawhole methods using highly mechanized procedures. By early 1981, however, thinking turned toward surface mining methods. The effort to quantify minable ore tonnage ultimately involved drilling 385 reverse-circulation rotary drill holes. These were drilled from August 1981 to March 1983 in several groups of holes. Each group, or drilling program, had a slightly different immediate goal or purpose. The holes were drilled to various depths using truck-mounted Drill Tech 40 drills with doublewalled 76 mm (3 in.) pipe with 134 mm (5.25 in.) three-cone rotary bits. Initially, wet drilling was employed using a cyclone collection system. Since cutting recovery was not as high as it should have been, all subsequent drilling was dry. The cuttings were collected and deposited by way of a cyclone into the sample bag. The pickup for the cuttings using the three-cone bits was about 50 mm (2 in.) above the bottom of the hole. Overall cutting recovery for the drilling program was estimated at 75%. Samples were taken on each 1.5 m (5 ft) of hole drilled. Each sample was split into three 48-g (1-2/3 assay ton) charges. The accepted value was the straight average of the three charges. Because of the known "nugget effect," assays were nearly impossible to duplicate. Therefore, to validate the regular assays, a series of screen fire assays were run. Based on this method of assays and checks, it was concluded that 10% more ounces would be produced than indicated by mine grade. Test pit The northernmost portion of the mine as planned is known as the Terraville test pit. This portion was mined ahead of the rest and separately. It provided answers to questions on slope stability, reserves correlation, mill recoveries, mining costs, and surface mining conditions in various weather and ground conditions since many boulders and much timber were expected. The mining plan for this portion of the pit was successful. More ore was mined than was expected. Mixing of Open Cut ore with underground ore in the mill feed was successful. Impact on the surrounding communities

Jan 10, 1987

By J. A. Bleeck

A discourse on the relationship between industrial minerals and paper production, concentrating on high grade, ultra fine ground calcium carbonate (mean particle size less than 2 microns) and precipitated calcium carbonate. The scope of the paper encompasses four basic areas relevant to the topic: 1. A tutorial overview of the papermaking process with an examination of various industrial mineral components in that process; 2. A discussion of basic technological topics pertinent to the utilization of carbonate in paper with emphasis on the relative aspect. Of natural ground calcium carbonate (GCC) and synthetic precipitated calcium carbonate (PCC); 3. An overview of paper and carbonate market, in both the United State, and Europe with emphasis on (a) current status and future growth trend. Of such market., and (b) discussion of the major influences on growth and development of such market.; and 4. Identification and discussion regarding the principal producers in calcium carbonate markets serving the paper indu.try in Europe and North America.

Jan 1, 1993

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By H. R. Weischedel

The art of wire rope inspection has advanced rapidly over the past decade. Present electromagnetic (EM) wire rope inspection instruments provide an important and often vital element of wire rope inspection. Some instruments are easy to operate and offer simple and clear data interpretation. Simultaneously, wire rope inspection and retirement standards are becoming simpler and more lucid. Future guidelines will he easy for inspectors to apply and for rope operators to fulfill. The thrust of evolving regulations is clearly toward periodic EM inspections supported by visual inspections. These development sallow even moderately skilled personnel to perform EM inspections of wire ropes. Therefore, it is now possible and cost effective for wire rope users to have EM and visual inspections performed by in-house personnel. In-house EM inspections have many advantages and offer an excellent return on the initial investment. Since EM inspections can detect rope deterioration in its beginning stage, wire rope users recognize that they are an effective preventive maintenance tool. For instance, the early detection of wear or corrosion allows immediate corrective action. This can easily double, or even triple or quadruple, the service life of a rope.

Jan 1, 1991

By Li Zhou

The kinetics of the dissolution of galena was studied by monitoring the mixed potential of a galena electrode in ferric sulfate solutions. The results show that the mixed potential of the galena electrode fluctuated with time in a regular pattern in a 0.1 mol/L Fe2(SO4)3 solution of pH 1.66 and in a 0.01 mol/L Fe2(SO4)3 solution of pH 2.33 at 35°C. The periodic accumulation and precipitation of lead ions at the galena electrode surface and the cyclical variation in pH at the galena electrode surface caused the oscillation phenomena.

Jan 1, 2008

By Junnan Chen, Hongwei Zhang, Wei Wang, Feng Xie

Thiosulfate is a green gold leaching agent that shows great potential to replace the highly toxic cyanide. Ammonia is traditionally used as the copper ligand in thiosulfate solutions to reduce the reactivity of copper ions towards thiosulfate, but it is a toxic reagent. As a result, efforts to replace ammonia with another complexing agent have received increasing attention. In this study, a novel alternative to ammonia is proposed to explore the potential use of the copper-malic acid-thiosulfate system. Experimental parameters include temperature, initial pH, copper, malic acid, and thiosulfate concentration. The feasibility of the copper-malic acid-thiosulfate system was discussed using Eh–pH and species distribution diagrams. Themodynamics analysis indicates that the mechanism of gold leaching in copper-malic acid-thiosulfate solution is mainly catalyzed by the Cu2( Mal)2H-2 2−/Cu(S2O3)3 5− redox couple. The capability of gold leaching in this system for processing the refractory gold concentrate is comparable to that of cyanidation and the traditional copper-ammonia-thiosulfate leaching processes. Thiosulfate consumption is greatly reduced in the presence of malate due to its strong chelating effect on the copper ions. Moreover, the copper-malic acid-thiosulfate system demonstrates a significant enhancement in leaching kinetics, making it a viable option for processing refractory gold concentrates.

Aug 1, 2023

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"The National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. Refuge alternatives typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The Mine Safety and Health Administration (MSHA) requires that the PRVs vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: a modified PVC check valve, an off-the-shelf brass/cast iron butterfly check valve, and a commercially available valve that was designed specifically for one manufacturer’s steel pre-fabricated RA and has been adapted for use in built-in-place (BIP) RAs located at one mine. PRVs used in tent style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with 30 CFR regulations. BACKGROUND The Mine Improvement and New Emergency Response Act of 2006 (Miner Act) (1) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement. Section 13 of the MINER Act specifically directed the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines, and the Department of Labor to act on the results of such research as appropriate. These mandates culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for the Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (specified as 0.18 psi, or approximately 5.0 in H2O), or at a pressure as specified by the RA manufacturer, above mine atmospheric pressure in the RA (2)."

Jan 1, 2016

By Kurt M. Larson

Future haulage cost projections led Foster Yeoman Limited into developing a fully mobile crushing and conveying system at its Torr Works quarry in Somerset, England. The purpose-built system has an effective throughput of 2,500 tonnes/hour and features an Orenstein and Koppel (O & K) manufactured walking frame, a Fuller-Traylor type 54 X 74 TC gyratory crusher, and unique mobile conveyor modules designed and manufactured by Foster Yeoman. Used in a single-bench operation in this 6 million-tonne per annum limestone aggregate quarry, the system is fed at the production face by 2 Caterpillar 992C loading shovels. The entire system is moved on a daily basis following production face locations.

Jan 1, 1986

By P. M. Soupios

The study of soft soil (wastes above the rock bed) an issue of great importance in civil engineering, is usually addressed by drilling boreholes. This method is rather expensive and time-consuming and although the information obtained is usually accurate, on the other hand it is much localized. Recently published researches have demonstrated the ability of the combination of geophysical exploration methods to estimate the thickness of deposited wastes, which provides the layered structure of the study area and certain, method depended, mechanical parameters as well. By theory, the frequency of resonance of an upper layer is a function of its thickness and the average shear velocity in it. Furthermore, the application of H/V spectral ratios of micro-tremors is a fast, straight forward and cost effective methodology, yielding the determination of the main resonant frequency of the soil. Based on this framework, 20 microtremor measurements have been carried out in a Landfill in Heraklion-Crete. Some of these measurements were deliberately close to drilled sites, where the basement had been reached. Three electrical resistivity tomographies were also used, in order to define the landfill structure such as, thickness, determination of different wastes distribution in the study area and other parameters. In addition, estimation of predictive Vs using empirical relationship between shear velocity and penetration resistance (SPT?s) were also conducted. Knowing the thickness and the resonant frequency, we estimated the shear (Vs) velocity of the waste cover. The final Vs model was confirmed using the results from the Vs-SPT correlation. The combinative implementation of the above mentioned geophysical and geotechnical methods have successfully defined geometrical and geotechnical/geophysical characteristics of the area under investigation in a fast and cost effective way.

Jan 1, 2005

By J. D. Potts

Installation of a horizontal air blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong coanda effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector to bailing airflow ratio, and a 5.1-cm (2-in) gap between the shroud and ground. The shelf was 15.2-cm (6-in) wide and located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2009

By N. Damiano, C. Zhou, R. Jacksha, J. Srednicki

Modern electronic devices and systems used to enhance miner safety and health are becoming commonplace in underground coal mines. The ability for these devices and systems to function properly in the presence of electromagnetic emissions from other electronic and electrical devices and systems is not entirely understood. To investigate potential electromagnetic compatibility issues of critical mine electronic devices and systems, researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting surveys of electromagnetic emissions in underground coal mines. This paper presents the measurement system, methods, and results of electric field electromagnetic emission surveys conducted in three underground coal mine environments in the frequency range of 10 kHz to 1000 MHz. The survey data show that in some environments electric field electromagnetic emissions in underground coal mines approached or slightly exceeded limits as defined by other industrial sectors.

Mar 2, 2022

By A. Benchekroun

The phosphate mining industry is confronted everywhere in the world with financial difficulties and low prices which prohibit further investments and development of new mines even in regions with a comparative cost advantage (North America/ North Africa/ and Middle East). But old mines are being progressively exhausted/ and if no replacement mines come on stream in the near future/ we may soon find ourselves (around the year 2000) with a global annual production capacity of 160 million tonnes of marketable phosphate rock instead of the capacity of 200 million tonnes existing today. Unless prices improve/ phosphate rock/ a non-renewable resource and a vital commodity to world agriculture/ may turn to be in short supply to world fertilizer industry. Whatever the extent of recovery of fertilizer demand/ the expected decline of the production capacity during the 1990 I s is bound to cause the disappearance by the year 2000 of the important surplus characterizing today the supply/demand balance.

Jan 1, 1995