Search Documents

By R. A. Hevia

Florida Power and Light is the fifth largest investor-owned electric utility in the country. It has a service territory that covers 35 counties, or 28,000 square miles, 2.5 million customers, and serves 5.6 million people. The total installed capacity is 13,470 MW, generated by four nuclear units, 36 oil and/or gas fired units, and 48 gas turbine units. Traditionally, FPL has been an oil-based utility. In 1979, this dependency on oil became obvious when 42 million barrels of oil were burned during the year. At that time, it was also projected that, based on the current estimates of customer growth and available generation capacity through 1990, FPL's residual fuel oil consumption would increase from the 1979 level of 42 million barrels (6.7 million m3) per year to approximately 55 million barrels (8.7 million m3) per year by the mid-1990's. Concern over this was further aggravated by the fact that it was difficult to estimate both the price and quantity of fuel oil that would be available over the next decade since changes in the world market, decisions by oil producers and refiners, and international political developments would all affect the availability of oil. Also, at that time, the price of residual fuel oil had increased drastically, and there was no reason to think that these prices would soon stabilize. Thus, oil back-out became a primary objective of FPL and since then, FPL has been actively investigating ways to decrease fuel oil consumption.

Jan 1, 1985

By Rusdian F. Kayadoe, Michael B. Hutahaean, Sandi A. Firmanulhaq

Deep Mill Level Zone (DMLZ) mine is located in Papua, Indonesia operated by PT Freeport Indonesia (PTFI) with approximately 1,500m below surface. The ore body extend 1230m width from northwest to southeast by 300–400m length east-west. The mine currently produces at full production of 80,000 tons per day until 2041. Part of the extension of current active production block and mitigation sits 225 m above the production block 1 (PB1) and 2 (PB2A and PB2B) which located in 2590L, named production block#4 (PB4W and PB4E). As the mining continues at PB1N, PB2A, and PB2B, the cave growth vertically and laterally to south perimeter of the footprint affecting the integrity of PB4W/E footprint. Currently, PB1N and PB2N are in active production whilst PB4E development continues from South against PB1N cave, as can be seen in Figure 1. A slight overlapping between PB1E and PB4E intentionally to promote cave connections between the two caves. Despite low stress model in the PB4E near existing caves, the PB4E cave propagation expected by the large strain and will be propagating in tension failure to the PB1E cave. Hence, designing the drill drives edge and first drawbell location as close as possible to the PB1E cave is necessary to guarantee cave connection. Since PB4 footprint development commenced in December 2021, there have been a substantial cave propagation observed from existing downhole monitoring. As the PB4 footprint designed perpendicular to existing DMLZ PB1 cave, adjustment of the development edge design is necessary to reflect the progression the loosening zone propagation to the South. Final life of mine design for extraction, undercut and ventilation level were decided in October 2023 considering latest update cave (fractured/ yielded) boundary. Numerical model of potential rock mass damage also aids the decision to locate the drift edge design. Predicting the cave progression impact is critical to both production at the existing active blocks and development of the new area. The use of cave shape data from year 2021–2023 gives an insight of the cave shape estimation at the end of 2024 when the undercut drift will be developed. This paper presents actual cave growth of active production blocks and its relative vertical progression impact as the result of drawing in order to plan for acceptable rate and provide mitigation once the minimum acceptable rock mass condition and minimum pillar threshold achieved.

Feb 1, 2025

By Eduardo Pimenta de Melo, Rambabu Pothina, Rajive Ganguli

Sensors are everywhere in the mining industry, with sensor information being used to monitor and operate processes. Therefore, when sensor information is wrong, economic losses can occur. Unfortunately, sensor errors are usually not detected till they become large. This is problematic as most calibrate their sensors no more than once a year (Beamex, n.d.). Using principles of data mining, where all relevant information is tapped to glean hidden information, Pothina [8] designed an algorithm to detect errors in temperature sensors in gold stripping circuit in Pogo mine, Alaska. This paper continued his work by analyzing the behavior of the algorithm on baseline data and testing the algorithm in new data and under more rigorous conditions. It also made a change to the algorithm. The modified algorithm performed very well in the new data. It also worked well under the new error conditions. Three types of errors were seeded, a fixed additive error (+ 2%), a fixed subtractive error (− 2%), and a noisy, normally distributed error, with a mean value of + 2%. Artificially seeded errors were detected within about 20 gold stripping cycles. Inherent bias in operation impacted algorithm performance by increasing the number of cycles needed to detect errors. This paper reinforced Pothina’s [8] conclusion that when data mining approach is used, sensor errors can be detected even when they are pretty low. Significant economic losses can thus be minimized.

By K. H. McDaniel

An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a U.S. Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of U.S. defense generated transuranic waste in bedded salt. In addition to its regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright © 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows ® application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System.

Jan 1, 1996

By Arthur D. Silber

The economic success and growth of any metropolitan region depends on mobility. Today, mobility between New Jersey and New York is threatened by a transportation system that cannot meet 21st century travel demands. The transportation bottleneck created by the Hudson River threatens the viability of one of the world?s great centers of commerce and culture. Fortunately, there is a solution: The Access to the Region?s Core Mass Transit Tunnel. The US$8.7-billion Mass Tran-sit Tunnel?s (MTT) new two-track line will double commuter rail capacity under the Hudson and create a new, state-of-the-art cavern station in Midtown Manhattan, with wide platforms, high-speed escalators and other features to improve riders? travel experience. The capacity and other benefits of the MTT project will launch a new era of prosperity for the region, just as the Pennsylvania Railroad did almost 100 years ago when it built the existing two, single-track rail tunnels that now form the sole commuter rail link between New Jersey and New York. The existing tunnels run from North Bergen, NJ, under the Hudson River to Pennsylvania Station at 33rd Street in Manhattan. Construction on the MTT, the largest public works project in the United States, is scheduled to start this year and continue through 2017. The MTT is ready to go to construction thanks to a major commitment of financial, engineering, project management and other resources from NJ TRAN-SIT, New Jersey?s statewide mass transit agency, and the Port Authority of New York and New Jersey, a bistate agency that operates the Holland and Lincoln tunnels, the George Washington Bridge and other major transportation facilities in New York and New Jersey. The project is also strongly supported by the state governments of New York and New Jersey, as well as that of New York City. The MTT is New Jersey Governor Jon Corzine?s number one transportation priority.

Jan 1, 2009

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By Peter B. Dowden, Robert A. Robinson

Boulders, frequently found in tunnels excavated through soils, can pose major problems for full face TBMs in terms of slowing or halting the tunnel advance, cutter damage, and abrasive wear. The paper aims to consider the problem as a whole, from the geological characteristics of boulder sites, to the appropriate physical design of theTBM, and its operation in boulder-laden soils. In addition, visualization of boulders and other subsurface obstructions by seismic methods and ground penetrating radar are reviewed. The paper will assist the construction planner in assessing the risks and preparing appropriate specifications.

Jan 1, 2001

By L. L. Lacerda, A. J. Blair

The Wolf Creek Upper Narrows Tunnel (Upper Narrows Tunnel) is one of the first major highway tunnel in the United States implementing the use of spray-on membrane for purposes of constructing a double-shell drainage solution between an initial shotcrete lining and a final cast-in-place concrete lining (Figure 1). In the case of the Upper Narrows Tunnel the primary membrane is constructed with a spray-on product manufactured by Degussa, namely Masterseal® 340 FA (MS 340) that has been utilized previously in other tunnel projects. Shotcrete-like in application, but differing in physical properties, MS 340 is now outdated, and is succeeded by Masterseal® 345 (MS 345), a nearly identical product, with improvements in material properties. Tunnel project histories utilizing either MS 340 or MS 345 are discussed and summarized with regard to the respective motives for prompting spray-on membrane selection and the realized benefits resulting from spray-on membrane construction. With an emphasis on the Upper Narrows Tunnel, project summaries discuss details of the aspects of design for spray-on membrane construction methodology as opposed to conventional sheet membrane construction methodologies. It is anticipated that experience gained during the construction of the Upper Narrows Tunnel with respect to other tunnel projects that have utilized spray-on membrane will be of use for future tunnels employing spray-on membrane in drainage solutions.

Jan 1, 2005

By J. R. Parga

In mineral processing, poor froth-flotation performance translates into both an enormous loss of revenue and an unnecessary waste of the ore reserve. In this context, Bacís Mining Company developed a versatile new, high-performance flotation-cell design that can be incorporated into various flotation circuits. The main feature of this circular cell is that it is comprised of two separate sections, namely, a flotation cell that uses wash water to minimize the entrainment of fine gangue particles into the froth product and an external bubble generator that produces small bubbles of relatively uniform size at a specified aeration-rate. The air/water mixture is blended with the pulp by gentle agitation, so as to enhance particle-bubble aggregate-stability. Comparative metallurgical performance with conventional flotation cells show that the power requirements and operating costs for precious metal flotation are three times lower, while the concentrate grade is 7% higher and the recoveries of precious metals are 5% higher.

Jan 1, 2009

By John E. Rourke, O&apos

This paper describes some of the results of a project for the design and demonstration of subsidence monitoring systems for underground coal mines. The project was designed to test monitoring systems described in an earlier feasibility report (O'Rourke and others, 1979). General objectives of the project were to develop reliable cost- effective monitoring systems for use above caving- type mining operations, over supported mines, and in urban undermined areas. Topics selected for discussion in this paper include a description of the instrumentation systems, the site conditions, problems of installation, resulting recommendations and an over- view of subsidence performance data obtained. There were some particularly difficult problems of installation to overcome at this site. Some of these could be experienced at any surface or under- ground project, others are probably more directly related to Western coal fields. Almost any subsidence monitoring program may face the following difficulties:

Jan 1, 1982

By Renfeng Song, Shaoyan Wang, Zhiqiang Zhang, Ke Guo

Leaching titaniferous magnetite concentrate with alkali solution of high concentration under high temperature and high pressure was utilized to improve the grade of iron in iron concentrate and the grade of TiO2 in titanium tailings. The titaniferous magnetite concentrate in use contained 12.67% TiO2 and 54.01% Fe. The thermodynamics of the possible reactions and the kinetics of leaching process were analyzed. It was found that decomposing FeTiO3 with NaOH aqueous solution could be carried out spontaneously and the reaction rate was mainly controlled by internal diffusion. The effects of water usage, alkali concentration, reaction time, and temperature on the leaching procedure were inspected, and the products were characterized by X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. After NaOH leaching and magnetic separation, the concentrate, with Fe purity of 65.98% and Fe recovery of 82.46%, and the tailings, with TiO2 purity of 32.09% and TiO2 recovery of 80.79%, were obtained, respectively.

Jun 16, 2021

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1991

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1993

By Gary Brendel

India produces about 70 Mt/a (77million stpy) of coal ash (fly ash and bottom ash) from burning about 200 Mt/a (220 million stpy) of coal for electric power generation. The average ash content is 35%. In contrast, the United States produces about 70 Mt/a (77 million stpy) of coal ash from burning 800 Mt/a (880million stpy) of coal for power generation. Its average ash content is less than 10%. In 1998, GAI Consultants Inc.(GAI) embarked on a federally funded, multiyear project to assist the government of India in solving its growing coal-ash management problem.

Jan 1, 1999

By Verya Nasri, Heather M. Ivory, Kevin Clarke, Eric Cole

Development of the New York City Water Supply System The New York City water supply system serves a population of almost nine million, including residents in neighboring counties. Peak day demands on the system are currently running at about 70 m3/sec (about 1,600 mgd), which is significantly lower than in the 1990s. This trend of reducing demands over the past 25 years, which has been experienced in other major urban centers in the US, is mainly the result of conservation measures and increased cost consciousness on the part of water users. In the long term, demands are expected to once again follow an increasing trend with population growth, so that by the end of the planning horizon of these studies, the year2045, the peak day demand is expected to increase to about 85 m3/sec (2,000 mgd).The system is served largely by surface water sources, regulated by a system of 19reservoirs and three controlled lakes, which are connected to the City by a series of aqueducts, the longest of which is about 87 km (54 miles). The total storage in the sys-tem amounts to about 560 billion gallons, providing a system firm yield of about1300 mgd. The Delaware system provides about 50% of the City’s water, the Catskill about 40%, with the remaining 10% provided by the Croton. The system as a whole, which is shown on Figure 1, has been built up over the past 150 years, and is truly a marvel of engineering. The Catskill and Delaware aqueducts both discharge into Kensico Reservoir, which is a daily balancing reservoir located in Westchester County about 24 km(15 miles) north of the New York City line. The two aqueducts extend south for a further 14 miles to combine again at Hillview Reservoir in the Bronx, which provides hourly balancing storage for New York City system. The Croton aqueduct runs nearby as shown on Figure 2, but does not connect into the two reservoirs. From Hillview Reservoir the water is supplied to the city via three main distribution tunnels, known as City Tunnels 1, 2, and 3. City Tunnel No.1 was developed in the 1920s as part of the Catskill system. City Tunnel No. 2 followed in the 1960s as part of the Delaware system. City Tunnel No. 3 (CT3) is partly under construction and partly in operation, and is being implemented to permit the other distribution tunnels to be taken out of operation for the first time for inspection and maintenance. Presently CT3 is supplied with water from Hillview Reservoir via a large underground valve chamber, the Van

Jan 1, 2007

Perhaps the most significant development in China's base metal sector is the discovery of major copper porphyries in northern Jiangxi Province and the adjacent southern Anhui Province. At the center of the new exciting district is the proposed Dexing copper complex, located some 350 km east of Nanchang, the provincial capital of Jiangxi. This project represents China's first attempt to put together a major large-scale open-pit operation, comparable in magnitude to Arizona porphyry operations. With the aid of Fluor Mining and Metals, the Chinese plan to develop a 135-175 kt/d open-pit mine, a matching large-scale mill, and the infrastructure needed to accommodate the big operations. An operation of this magnitude would significantly reduce China's import requirements by some 75%. China imports of the red metal are running around 200 kt/a. Under the direction of the Ministry of Metallurgical Industry, the Chinese are currently operating a 10-kt/d mine and mill with equipment primarily of Chinese origin. Dexing engineers told ME that they are considering a possible scale-up to 20 kt/d. How this effort will ultimately jell with the major expansion program is largely a matter of conjecture. Fluor Mining and Metals received a $10-million contract in December 1978 to develop a preliminary engineering and design program. While the original plans called for a 175-kt/d capacity complex, the Chinese subsequently decided to scale it down somewhat. The current proposal is around a 135 kt/d, which would in- elude the existing operation, according to Dexing engineers. Completion of the engineering and design phase is expected by March 1980 and a go-ahead decision will likely be made at that time. The value of the engineering and construction contract is estimated between $800 million and $1 billion. At right, mined ore is dumped 150 m down the mountain to a holding pocket below for rail haulage to the processing plant. Below, a Chinese miner tackles the universal problem of hard toes in the pit with a jack leg. Reserves and Early History The Dexing mineralization consists of three principal ore bodies, including the Chushahung on the north mountain, and the Tungchang and Fuchiawu on the south mountain. Combined ore reserves are estimated by mine geologists at 1.7 Gt of 0.4-0.5% copper. As is characteristic of porphyries, the ore contains important associated values of molybdenum, rhenium, pyrite, gold, and silver. There is also some secondary calcocite and bornite with an oxidized capping. Historically, copper was recovered with iron from the pregnant solutions emanating from the Tungchang deposit as early as the Tang Dynasty (700 AD). Modern day exploration was conducted by the Bureau of Geology in 1956 and reserve figures were es-

Jan 3, 1980

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

By Malte J. M. Gurgel, Axel Preusse

Recent three-dimensional surveying techniques have opened up new opportunities for the registration and monitoring of underground cavities. There are essentially two main methods available: Laser scanning, which is used both above surface and increasingly underground, and photogrammetry, which is also experiencing a renaissance with techniques like structure from motion through the algorithm-based orientation of high-resolution images. Both methods provide the capability to reconstruct reality by various 3-D products like points clouds and meshed models. However, they differ significantly in the steps of registration and calculation as well as in the resulting evaluation options.

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014