Search Documents

By Jamal Rostami, Levent Ozdemir, Amund Bruland, Filip Dahl

Cerchar Abrasivity Index (CAI) is one of the commonly used tests to evaluate rock abrasiveness for cutter life/cost estimations of TBM projects. There are at least 3 style machines, 2 different pin hardness, and the test could be run on fresh rock surface VS a sawn surface. Each of these parameters has a meaningful effect on the results, but its impacts were not fully understood nor its implications well explored. This paper reviews the current practice of Cerchar testing and its implications on geotechnical investigations related to TBM tunnels and provide a set of guidelines on testing and reporting of the test results for future projects.

Jan 1, 2005

By G. T. Homce

Most electric motor predictive maintenance methods have drawbacks that limit their effectiveness in the mining environment. The U.S. Bureau of Mines is developing an alternative approach to detect winding insulation breakdown in advance of complete motor failure. In order to evaluate the analysis algorithms necessary for this approach, the USBM has designed and installed a system to monitor 120 electric motors in a coal preparation plant. The computer-based experimental system continuously gathers, stores, and analyzes electrical parameters for each motor. The results are then correlated to data from conventional motor-maintenance methods and in-service failures to determine if the analysis algorithms can detect signs of insulation deterioration and impending failure. This paper describes system design and implementation. At this writing, however, installation is still underway, and field data analysis results are not yet available.

Jan 1, 1994

By Cheng Li, Yanlei Wang, Lingrui Kong, Jianxin Tang, Fang Yuan

Coal mined-out areas have a significant impact on mining safety and affect the pressure distributions of neighboring coal faces. The PFC3D software is used to study the goaf mechanical characteristics, and the core loading test verifies the rationality of the numerical simulation method. The results from the numerical modeling showed that the void ratio, particle size ratio, and particle size distribution of the rock particle sample (RPS) had a significantly remarkable influence on the compression deformation characteristics of the rock block. The parallel-bond tensile strength and parallel-bond cohesion had a notable impact on the compression deformation traits of the rock block only when the axial stress level was lower than 12 MPa. By contrast, when the axial stress exceeded 5 MPa, the effective modulus significantly influenced the compression deformation features. However, the stiffness ratio, loading rate, and parallel-bond friction angle had almost no effect on the compression deformation characteristics. Furthermore, when the stress level was less than 10 MPa, the stress–strain curves from the rock core samples’ numerical simulation and loading tests were approximately linear. In addition, the Pearson correlation coefficients of the stress–strain curves suggest that the goaf zone’s core numerical simulation results had a robust correlation with the loading test results. The findings of this study can serve as a reference for the field application of PFC3D software and safety assessments in goaves.

Jan 18, 2022

By R. Sharma, S. Svoronos, S. Gupta, N. A. Abdel-Khalek

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

By G. T. Austin

Every year the United States consumes millions of dollars worth of abrasive materials as blasting media. Entrained in either a gas or liquid stream or propelled by paddles or wheels, they are directed onto the surface of another material to modify that surface. The modifications to impacted surfaces include cleaning, cutting, deburring, etching, finishing, and peening. Blasting media can be either organic or mineral abrasive materials. Information and data presented are for only a portion of the mineral abrasives, they are; fused aluminum oxide, coal slag, copper slag, garnet, metallic shot and grit, nickel slag, olivine, silica sand, silicon carbide, and staurolite.

Jan 1, 1994

By H. C. Liang

Reverse osmosis (RO) and nanofiltration (NF) are widely regarded as being best available technologies (BATs) for removing contaminants of concern from water. In recent years, NF or RO treatment has increasingly gained more acceptance in the mining industry for treating mine water to remove a wide assortment of contaminants, either for meeting discharge standards or for internal re-use in mining processes. Consequently, the number of NF or RO membrane mine water treatment facilities has steadily increased. Although NF or RO membrane filtration can be a powerful tool in mine water treatment, especially when multiple contaminant removal is required, it also has many potential disadvantages. Besides the generally higher capital and operational costs for the high pressure membrane processes, organic constituents in mine water may foul the membranes, while inorganic compounds such as gypsum, calcite, or silica are liable to scale the expensive membranes if proper pre-treatment processes are not implemented. Additionally, because these membrane treatment processes generate a substantial reject or brine waste stream in addition to the clean treated water or permeate stream, brine management also needs to be considered carefully when deciding upon the viability of an NF or RO mine water treatment process. Because of these issues, it is important to conduct detailed analyses of the trade-off between selecting NF or RO vs. using chemical treatment processes when designing a mine water treatment facility.

Jan 1, 2012

By L. Bomvisinho

As a result of today?s requirements for larger mills with higher power demand, and in order to cope with maximizing throughput, and optimize grinding efficiency, the minerals industry is increasingly relying on the robust Gearless Mill Drive (GMD) solution. This paper describes the new features introduced with the revolutionary ABB drive controller for Gearless Mills, and explains the benefits this can bring to the operation. Extensive surveys have been performed with GMD users to gather suggestions and understand the market wishes. As a result the new driver controller capabilities and functionalities focus on safety, high availability, operational flexibility and remote diagnostics.

Jan 1, 2010

A large-diameter road tunnel will cross beneath the strait in Istanbul and expand the infrastructure bottleneck between Europe and Asia. The technical planning of the tunneling operations poses complex challenges. Therefore, the construction consortium ordered a specially adapted tunnel boring machine (TBM) from Herrenknecht. The 13.6-m (44.6-ft) machine, a Mixshield, was completed in early July 2013 in Schwanau, Germany. To get from the European to the Asian side of Istanbul, people and goods have to cross the Bosporus Straits. So far, two road bridges as well as ferries provide the only transport link between the two parts of the city and the two continents. The tense traffic situation for the nearly 14 million residents of the city and for international transit traffic should be improved considerably thanks to the construction of a new road tunnel under the Bosporus. ?The project is certainly one of the most challenging tunneling operations currently being addressed in the world,? said Herrenknecht project manager Georg Schleer. The route of the ?Istanbul Strait Road Tube Crossing Project? runs around 100 m (330 ft) below sea level at its deepest point. The interior diameter of the tunnel will be 12 m (40 ft) so that two lanes in each direction can be accommodated. They will extend one above the other on two levels. 3.34 km (2.1 miles) of the tunnel with a total length of 5.4 km (3.3 miles) are being created by a 13.6-m- (44.6-ft-) diameter Herrenknecht TBM that will begin its underground mission from a launch shaft on the Asian side.

Sep 1, 2013

By John J. Murray, Michael T. McRae, Michael A. Krulc, Kathy L. Schuler

The San Vicente Pipeline Tunnel Project involves the construction of an 8.5-foot-diameter water pipeline in an 11 mile tunnel in San Diego, California. The tunnel is located in extremely variable geologic conditions of strong granitic and volcanic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. One reach of the tunnel is a 5,200-foot mixed face reach that includes Friars Formation Conglomerate overlying granitic rock. Due to the variable ground conditions in this reach, the use of a TBM was deemed too risky and the contract documents required drill-and-blast and hand mining methods. Although it was not required, the contractor elected to construct this reach using NATM methods. This paper describes the geology of the 5,200-foot mixed-face reach, the design evaluation, and the construction challenges faced on this project.

Jan 1, 2007

By Paul Taurasi, Mahmood Khwaja, Anjuli Corcovelos, William Brick

California’s San Diego County Water Authority provides a safe and reliable water supply to more than 3.3 million residents through twenty-four member agencies. The 2nd Aqueduct pipelines, a critical infrastructure consisting of three large-diameter pipelines, are susceptible to natural threats including streambed erosion, channel migration, and seismic hazards within the 3,840-foot-long Moosa Canyon segment of the alignment. A state-of-good repair, hazard mitigation, and resiliency project is progressing to ensure uninterrupted water supply. For each pipeline, a segment will be replaced by tunneling. A high-level project development approach is presented, focusing on alternative selection, environmental and geotechnical considerations, and operations and maintenance constraints.

Jun 13, 2023

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By Bryan Ulrich

Rroundtable 2009, a Knight Piésold and Co.-hosted roundtable discussion on mine closure and cover design was held at the Red Lion Inn and Casino in Elko, NV on Feb. 12, 2009. Knight Piésold?s Bryan Ulrich and Steve Boyce, as well as Knight Piésold representatives Cynthia Parnow and Corey Conrad from Denver, CO, and Rick Frechette from the Tucson, AZ office were on hand to help facilitate the discussion. The meeting played host to approximately three-dozen attendees from four states. Attendees included personnel from seven mining properties and attendees from corporate offices. The majority of attendees were people directly involved with environmental work on a day-to-day basis. Other attendees were project managers whose jobs involve some level of environmental focus. The purpose of Roundtable 2009 was to exchange ideas and information pertaining to mine closure and cover design associated with almost any aspect of a mining operation. This type of forum provides a less inhibited format for discussion, when compared with traditional conferences and symposia. In the roundtable format, lively discussions are encouraged. This discussion was the fourth in the series of Elko Roundtable events. Previous roundtables pertained to heap leach pad design, construction and operation; design, construction and operation of tailings storage facilities and site-wide water considerations. The initial subtopics for Roundtable 2009 included:

Jan 1, 2009

Barrick Gold plans to have four new gold mines in production by 2006. Together, the mines would increase the company’s output by 40 percent. The projects include Veladero in Argentina, Alto Chicama in Peru, Cowal in Australia and Tulawaka in Tanzania. All of them are scheduled to begin production between the first quarter of 2005 and the first quarter of 2006. They are expected to drive Barrick Gold’s growth profile to a target of 211.5 to 217.7 t (6.8 million to 7 mil-lion oz) of gold production in 2007. The company’s projected output for 2004 is 152.4 to 155.5 t (4.9 million to 5million oz) in 2004. Overall, higher production and lower costs are expected in the early years from the new mines.

Jan 1, 2004

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By K. Wongaew, R. F. Cook, J. E. Carlson, T. Cleys, C. R. Smith

Steel fiber reinforced concrete segmental rings are the final tunnel lining for approximately 85% of the alignment for a 6.706-meter (22-foot) internal diameter tunnel being built as part of the East Side Combined Sewer Overflow Tunnel Project. This paper describes the approach adopted for the design of the steel fiber reinforced concrete segments, the development of the performance criteria for the segments, and the testing program used to confirm the performance of the materials and segments in the laboratory and in the field.

Jan 1, 2007

By B. Caro Vargas

The Toulon South Tunnel in France is the second part of a project started 20 years ago. After the problems and delays suffered during the construction of the North Tunnel, due to a complex geologic context of highly fractured and soft rocks under a highly urbanized environment, a very dense automatic monitoring system was implemented to control the settlements of surface (more than 1000 points), the structures adjacent to the tunnel alignment and the underground galleries being constructed. The latest automatic instrumentation systems were installed, using for example AMTS capabilities in terms of ?automatic prismless settlement monitoring?. All the data (geotechnical, structural and geological) was gathered in a global automatic data acquisition system and continuously available on a web based interface. Three different threshold levels (notification, anomaly, alert) were set up, each one with a differential and an absolute value for settlements. Depending on the actual geological site conditions and the actual monitored settlements, different supporting systems and excavation techniques were used. Furthermore, the monitoring data was also used to predict and anticipate the future settlement, by comparing it continuously with the theoretical Peck settlement curves. This method allowed a better risk management by limiting the settlement on existing structures and helped to secure the Works progress schedule, for a project that lasts from July 2007 to March 2011. The implementation of this observational method application is presented in this paper.

Jan 1, 2012

By Daniel H. Israel

Indian tribes own a substantial portion of the West's minerals. More importantly, Indian reservations contain coal, oil and gas, uranium, and oil shale reserves in unusually large and unencumbered blocks. Many tribes are now prepared to intensify development of their large reserves knowing that they can offer energy partners the unique opportunity to develop major energy facilities free of overlapping local, state, and federal permitting authorities. The tribes, therefore, can offer mineral developers both substantial reserves and an unusual degree of freedom from a multiplicity of government regulation. In the past, Indians and energy companies enjoyed only partial success as business partners. Indian tribes lacked the resources and know-how to act as equal partners with large oil and gas and mining operators. The tribes relied on the Bureau of Indian Affairs (BIA) to initiate and execute reservation energy projects, and as a result the tribes never developed adequate tribal structures and the expertise to responsibly manage their energy resources. At the same time industry made little effort to understand and learn the laws, customs, and institutions existing on Indian reservations. To the contrary, industry found it easier to bypass the tribes and deal with BIA officials. But the situation has changed. In 1975 the tribes organized an effective coalition, the Council of Energy Resources Tribes (CERT), which recently acquired substantial federal assistance to bring the tribes a level of technical and business expertise that begins to equal that of industry. Because the tribes have changed the rules of the game, industry must now change and learn to work directly with tribal governments. A working knowledge of Indian law, practices, customs, and policies must be acquired by energy companies before beginning negotiations with tribal governments for development of reservation energy resources.

Jan 6, 1980

By Artur Skoczylas, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

In many underground mines the excavated ore is produced during the blasting process. Drilling machines that are used to drill the blastholes, where later the explosives will be mounted, are crucial for this task. In order to optimize the currently used techniques, great emphasis is placed on increasing the efficiency and safety of blasthole drilling operations. The natural consequence is the development of monitoring systems and algorithms for processing operational and historical data. In this article, we present the result of the analysis of drilling data carried out as part of the IlluMINEation project. The paper proposes an algorithm for work cycle detection for drilling machines, together with the estimation of general operating parameters and diagnosing the drilling process on the basis of long-term data. Based on the available data, selected components of the drilling cycles have been indicated. Several approaches based on the parameters of the defined cycles are proposed. These approaches can be used in the future to create a full-fledged system for examining the effectiveness and safety of mining drilling rigs.

Jun 25, 2023

By John J. Dran

[This paper summarizes the more popular mineral valuation techniques being used by the dining industry, and attempts to demonstrate how they are Interrelated and where some are in error when compared to modern methods of financial analysis. The academic community and the larger and more sophisticated raining companies, have largely rejected the older valuation methods such as the, Hoskold and Morkill concepts and replaced them with "discounted cash flow" (DCF) techniques. The relevancy and usefulness of the older methods have been questioned primarily on the basis of their underlying assumptions that mining companies do not have numerous alternative investments and must use sinking funds deposited at market or ?safe" rates of return to recover the purchase price of mineral reserves. The ability to reinvest In numerous (often non-mining} alternative business ventures, the changing purchasing power of the dollar, corporate income and other taxes, depreciation and depletion allowances, and modern financial management practice, all mitigate against the continued use of the older valuation methods, especially for the larger mining companies. Snail mining companies and Individuals still use these methods largely out of habit and familiarity. This paper attempts to point out the weaknesses and strengths of the valuation methods In current use in the hope that these techniques may be better understood and [rcrn] appropriately applied.]

Jan 1, 1973