Search Documents

By J. Manrique, B. Bustamante, P. Altamirano, J. Mendoza, J. Reyes

With no doubt, Peruvian mining potential is great as well as the energetic one. Unfortunately, this potential is threatened by social unrest. Several methods and strategies from different standpoints have been rehearsed with respect to unrest in Peru, however, the problem goes on without getting the right conflict interpretation and most of all, effective solutions are not achieved. The mining unrest dates from ancient times and has not always had the same stages nor the same demands. In the 20´s and 30´s, conflicts focused on workers’ rights and demands. In the 70´s, conflict focused on mines nationalization that were under foreign control. In the 80´s, conflicts took place because of requesting better wages, better working conditions, better mining profits distribution and more investment in communities that surround mining projects. It is very important to highlight those transversal demands such as land purchase, agricultural property, impacts and water reduction as well as pollution, impact on water systems and disappearance of springs have always been present over the historical period.

Mar 2, 2022

By Charles A. McLean

Bucketline dredges are machines for excavating large relatively unconsolidated or weakly consolidated materials from below water level. They are at the upper end of the capital cost range and the lower end of the operating cost range for placer mining machines and have digging capacities, typically, of from 100 cubic yards of bank measure material per operating hour for a shallow digging dredge carrying 2 cubic foot buckets to 1500 cubic yards per hour for a large deep digging dredge with 33 cubic foot buckets. Bucketline dredges used in the mining industry have their mineral processing plants mounted aboard the digging hull. Since dredges are high capital cost items, they require large ore reserves, typically at least ten years. Because of their high capital cost they are usually operated around the clock and for as many months of the year as weather conditions will permit. Typically a well run dredge operating year round would be expected to operate for 600 hours per month. Dredges operated in cold climates cannot operate when the weather freezes the dredge pond or the gravels, and dredges operating at sea cannot operate when high waves might batter the digging ladder against the bottom or upset the mineral extraction process.

Jan 1, 1992

By Dirk Timmerman, Klaus Schönert

This paper reports on the results of research on counter flow classification of - 10 µm particles. Two classifiers were designed and constructed, the first semicontinuous and the second fully continuous. The latest version operates continuously with recoveries of fines up to 90% at feed loads of 30 vol.%, separation sharpness X25/x75 up to 0.83, without bypass and cut sizes down to 1.4 µm (x50 from separation efficiency curve).

Jan 1, 1995

By I. C. Watson, J. W. Klokow, A. F. Knoetze, R. G. B. Pickering

In the late 1970s and early 1980s there were a number of attempts to use Tunnel Boring Machines in deep level gold mines. These attempts must be regarded as unsuccessful. Since then there have been comprehensive developments in tunnel boring equipment and tunnel support technology. This paper defines the problems experienced in those early trials, reviews the technology development, and concludes that tunnel boring in deep level goldmines can be justified in today’s environment.

Jan 1, 1999

By William C. Beebe, Russell E. Martin

An account of driving and concreting two 900 m railroad tunnels for the Denver and Rio Grande Western Railroad under emergency conditions. Details the importance of on-site decision making by the Owner in completing the project successfully in record time. A general description of the geology and construction methods. The Thistle Drainage Tunnel drained water impounded behind the Thistle slide and serves as permanent diversion of the Spanish Fork River and Thistle Creek around the slide area. The project involved 684 meters of 5 m horseshoe tunnel, a 5 m diameter raised shaft and 23,000 cm of cut excavation.

Jan 1, 1985

By Roger E. Melley

Since startup of the Syncrude Canada Ltd. (SCL) oil sands facility in northern Alberta 15 years ago, numerous improvements have been made in the ore conveying system and equipment. The unique nature of the material conveyed coupled with the wide range of environmental conditions encountered results in a number of unparalleled challenges. Most of the improvements have been brought about through the use of detailed field evaluation. Numerous publications are available that detail the various aspects of conveyor technology, and a significant list of papers are presented each year adding to the knowledge in this field. In the area of power formulae in the mid- 1970s, there were two major sources for use in the design of the SCL conveyors: the Conveyor Equipment Manufactures Association Handbook, 1988, and DIN Specifications 22101: Belt Conveyors for Bulk Materials, 1982. These sources were supplemented by the knowledge of the belt and conveyor equipment vendors and from the general literature. The SCL design was based on the CEMA formula. However, it was accepted that this empirical approach had been developed for use with more conventional materials in more reasonable climates. To accommodate

Jan 1, 1993

By D. T. Maiers, P. L. Wichlacz, P. A. Pryfogle, J. H. Wolfram

The effects of metal solution concentration, biomass density, length of exposure time, and pH were determined for biosorption of molybdenum (Mo) and chromium (Cr) by three organisms. Results indicate that it is possible to sorb Mo and Cr from dilute solutions. Differences were observed in the abilities of an organism to sorb Mo and Cr as well as among respective abilities of the three microorganisms. This suggests an inherent selectivity of the organism which may afford the means to control a sorption-based process. Results also indicate that the metal sorption abilities of these microorganisms depend on duration of exposure, biomass density, solution pH, and the metal concentration of the solution. Each of these parameters suggests an additional means of controlling the sorption process.

Jan 1, 1989

By R. L. McNearny, K. A. Barker

A study was conducted to compare physical and numerical models of the block-caving mining method. Results from the numerical analysis closely simulated the blocky behavior of the physical model, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1999

By Kevin Stuffle, James E. Sharp, Sean Premeau

Two process enhancements for the biological oxidative pretreatment of sulfidic gold ore for subsequent treatment with cyanide are discussed. These are the use of a high areal density ring and pin packing (BioBalls™) as substrate, and the use of a novel biological ferric generator. The BioBall™ packing when coated with concentrates for heap leach processing offers higher areal densities, while leaving more open volume for fluid flow than more commonly used substrates such as aggregate. An oxidation rate study was performed on crushed auriferous arsenopyrite whole ore to demonstrate the benefits of using the packing. The auriferous arsenopyrite grading 2.9% Fe and .212 OPT gold was 50 percent oxidized in 24 days. The biological ferric generator is a passive air-side trickle bed reactor that efficiently converts ferrous to ferric in a process stream. Conversion rates of .8g/L h ferrous to ferric are routinely obtained. Although the biologically generated ferric solutions have not yet been tested on gold ores or concentrates, prior work has demonstrated that the high ferric solutions which will result in rapid oxidation of sulfidic gold ores or concentrates.

Jan 1, 1997

By Randall J. Essex

Public and private owners of infrastructure projects face a number of real and perceived constraints when considering design-bid-build (DBB) procurement for underground projects. Thus, they may not be considering all of the available contracting approaches available to them. To the extent that the North American tunneling industry believes improvements can be achieved through better forms of contract, we have an opportunity and responsibility to bring these ideas to the owners of our projects. This paper offers suggestions for how we can climb out of our DBB Paradigm Sinkhole—and share some of the benefits of alternative contracting methods.

Jan 1, 2003

By J. S. Hattrup

INTRODUCTION Tunnel boring machines in non-abrasive competent rock with little or no water have set new performance standards in the driving of tunnels. However, when the machines have hit blocky or running ground, they have encountered difficulties. The success of a tunnelling machine is usually due to a thorough geological investigation which accurately describes the rock conditions, a well designed tunnel support system, and a tunnel boring machine designed to cope with these conditions. In some cases machines have had to be modified in the tunnel after the machine had commenced boring, because geological conditions were not correctly anticipated before tunnelling began. The features described herein are not a panacea for all conditons, and some of them, like an auxiliary thrust system that thrusts off a precast invert segment requires pre-planning of work on the part of the contractor. CUTTERHEAD DESIGN Figure 1 shows typical cutterheads of ten to fifteen years ago. Note the large buckets and large openings between the buckets. These large openings were considered necessary to gain easier access through the cutterhead for cutter changes. The standard cutter in those days was an 11 inch or 12 inch cutter with small bearings, and was generally a delicate tool for the duty it was to perform. These large buckets would clog up if a formation with clay seams was

Jan 1, 1981

By X. Zhou

A novel flotation device, cyclonic static micro-bubble column flotation (FCSMC), was introduced in this paper. FCSMC has been widely applied for fine coal preparation in China, and its application has been further expanded to the mineral processing industry. The FCSMC system features a unique cyclonic structure which enhances the separation performance of the column. In this paper, the cyclonic separation mechanism of FCSMC process was investigated, and corresponding kinetics equations were established to probe the separation principle of this device. Some typical examples of using FCSMC to separate different materials including coal, copper, fluorite, etc., were presented. Key words: cyclonic static micro-bubble flotation column, cyclonic separation

Jan 1, 2008

By C. Vasquez, A. Nieto

In past drilling programs for a multi-seam Texas lignite reserve, extensive e-log data was collected; however, little laboratory analyses were performed. As a cost and time saving incentive, sampling of lignite was intensified. In a recent drilling program in east-central Texas, detailed laboratory analyses and e-log information was gathered on a multi-seam lignite reserve of the upper Wilcox Group. This data will undergo statistical and geostatistical techniques in an attempt to discern whether or not predicted Ash and Btu/lb values can be derived from the e-log gamma-density relationships. Final characterization of the dataset will be used in a geostatistical model of that reserve. This model will be the basis for further geological investigations and mine planning.

Jan 1, 2004

By A. D. Shuloyakov, V. A. Zukerman, G. A. Finkelstein, V. I. Kurets

Possibilities of electric pulse disintegration are discussed with emphasis on high selectivity of the process as compared to mechanical comminution methods especially when applied to polymineral ores. Physical explanation of this phenomenon is suggested. The authors present results of some experimental tests illustrating regularity of this phenomenon irrespective of origin of ores or dissemination pattern of valuable minerals including both dissipated and accessory minerals. Some operating plants applying this principle are described the plants used either for mineral research purposes or for obtaining pure monomineral fractions or for treatment of gems to be faceted. Obstacles for implementation of this technology are mentioned.

Jan 1, 1995

By Peng Yu-mei, Cao Zhi-yun, Fan Qing-en

In China, an enormous amount of Au-Ag bering calcines, residues and tailings are produced each year from various sources in mining, metallurgical and chemical industries. For a long time, these materials have been either stored up in dumps or disposed of into rivers, resulting in not only waste of resources but also severe environmental pollution. It is therefore of great significance, both from economical and public welfare points of view, to recover efficiently and make full use of the metallic values from these miscellaneous materials. In this paper the physical and chemical properties of these Au-Ag bearing calcines, leached residues and tailings are described and the current status of their utilization are briefly outlined, followed by a more detailed description of some innovative processes now in practice. Lastly, the potential prospects of gold and silver recovery from these materials in China, particularly in the Hunan province, are envisaged.

Jan 1, 1998

By J. Iannicelli

A variety of domestic bauxites have been beneficiated to meet refractory grade standards by use of high intensity, high gradient, wet magnetic separation. Besides reducing the iron content to less than 2%, the Ti02 content of the bauxite was also reduced. The beneficiation can be accomplished by means of a simplified wet process flow sheet with an estimated cost comparable to that of water washed, filler grade kaolin. The process has been carried out on a small pilot plant and then scaled to produce 25 tonnes of calcined refractory bauxite meeting National Stockpile Specifications.

Jan 1, 1984

By Gary PE Beerkircher

A brief history of banana screen development and evolution will be presented along with the operational advantages of the large banana screens available in the industry today. Applications of the large banana screens will be presented as well as the economic advantages that the use of large banana screens can offer to the Mining lndustry today. Banana screen installations in metal, non- metal and coal mining applications will be presented.

Jan 1, 1997

By Chen Bingchen, Ma Shaojian

A new magnetic liner, with unique magnetic circuit and novel structure designs, was developed. It was characterized by light weight, low noise, as well as corrosive and abrasive resistance. The wear rate of the magnetic liner was one twentieth and one ninth those of the manganese-alloy steel and rubber ones respectively. The forming mechanism of the protective layer and that of influencing factors on magnetic liners were also investigated. The research results could not only instruct using magnetic liner, but also widen their application.

Jan 1, 1995

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By Cheng Zhengbing, Sun Baoqi

This paper summarizes several chemical purification methods used for producing high-pure industrial minerals These methods, mainly including alkali melting, acid leaching, oxidation-reduction bleaching, are respectively used to eliminate the impurities such as silicates in graphite and diamond, ferric oxides in quartz sand or other valuable silicate minerals, colouring impurities in kaoline, barite and other minerals which are required to have a high-whiteness. The fundamentals of the chemical purification methods and some practical examples in China are introduced in the paper.

Jan 1, 1995