Search Documents

By Daniel Hodouin, Claude Bazin, Sami Makni

Computer systems, installed in mineral processing, are designed to accumulate massive amounts of real-time data. Frequently these data are only partially processed because of the lack of adequate methods and the limited accuracy of mineral processing sensors. Methods are proposed to estimate missing data and reconciliate sensor data on a real-time basis. They are based on dynamic extension of steady-state techniques such as the node imbalance minimization or the least-squares mass balance adjustment techniques. The methods are illustrated for simulated and actual flotation data. Their data upgrading ability could be used to improve process monitoring, control and optimization.

Jan 1, 1993

By R. L. Schmidt, Williamson. T. N.

INTRODUCTION This paper describes one of several research projects funded by the Advanced Research Projects Agency to extend the technology of rapid underground excavation. This study and field research effort are to investigate alternative means to determine rock and geological conditions in advance of a tunnel boring machine (TBM). Approximately 1 year of a planned 3-year program has resulted in the definition of three candidate drill systems. Hardware has been assembled to field test these candidates and testing has begun. The 3-year objective is to develop a single optimum prototype drill and test it in an active TBM operation. ACKNOWLEDGMENT This research was supported by the Advanced Research Projects Agency (ARPA) of the Department of Defense and was monitored by the Bureau of Mines under Contract No. H0210037. The authors and sponsoring agencies are indebted to the quarry operators in California, Virginia, and West Virginia who offered assistance including access to their properties.

Jan 1, 1997

By John H. N. Yen, James M. Marquardt, Larry H. Heflin

INTRODUCTION On February 17, 1995, WMATA Contractor J.F. Shea holed through the last segment of rock tunnels of the planned 103-Mile Rapid Transit System for the Washington Metropolitan Area Transit Authority. Through the joined efforts and cooperation between the owner and the contractor, the project was completed on time and within budget. The Glenmont extension is on schedule to open in Mid-1998. The complete 103-mile system is scheduled to open in 2001. WMATA’s earlier 19 miles of rock tunnels had been done since 1976 ? By drill and blast with heavy horseshoe steel sets, sets with shotcreting over wire-fabric by TBM and NATM. All rock tunnels were primarily in metamorphic gneiss and schist, part of an east coast lithology that outcrops in a band running from below Richmond, Va. To above New York City. The 5,400 ft. long twin six meter tunnels of the Glenmont line had been earlier de-signed in 1979 by URS of NYC using Jenny Engineering of Pittsburgh, Pa., as a tunnel design specialist sub consultant. Jenny had provided two alternative designs, one conventional drill and blast horseshoe and one for Tunnel Boring Machine. Funding considerations had put the design on the shelf and it was clear that the state of the art had led to improved design methods in the intervening years. Before URS was tasked to update their design in1992, the Authority reviewed its earlier hard-rock experiences in light of the funding mandate to complete each segment on a limited budget and an expedited schedule. Many factors considered and many opinions were in leading to a final decision to drop the earlier designs and redesign for a single designated means of tunneling. That method was the New Austrian Tunneling Method. The NATM had been used earlier on WMATA for both soft-ground and rock tunnels. In the public’s eyes the NATM had become inextricably linked with the use of PVC’s and filter material enveloping or partially enveloping the underground structures to give the holy grail of tunnels, a water-tight structure. Although this link of waterproofing methods with excavation and support methods was essentially severed, a general feeling of their interdependence no doubt helped lead to acceptance of the NATM decision because of the waterproofing design that accompanied it. The Authority decided to drop the TBM and conventional options and provide bid documents for NATM only. URS asked LAW Engineering of Atlanta to provide the NATM design of the tunnels and associated shafts.

Jan 1, 1997

By S. Lin, Y. J. Wang

Through an example three fan ventilation network concepts of subsystem solution and characteristic curves of a multiple fan ventilation system are introduced. The major steps of defining a subsystem, working out the subsystem equations, constructing a solution curve and a characteristic curve, and determining the operating points of the reference fan and the ventilation system are systematically demonstrated through three and two-dimensional curves. Also briefly discussed are the main features of a subsystem characteristic curve.

Jan 1, 1993

By Leslie M. Burnside, Gene E. McClelland, Roy R. Cellan

Revegetation of neutralized heap leach material in the arid environment of the Great Basin represents a challenge of avail­able technology. The chemical and physical environment of spent and neutralized ore is inhospitable for germination and establishment of desirable long term vegetation. Common soil amendments were tested to dete1mine if the heap material could be made more conducive to plant growth. Decommissioned heap material profile samples were collected and reconstructed in columns at bench scale. The column profiles were amended and subjected to three leaching regimes, and representative meteoric conditions. The soil amendments provided positive results for ameliorating the heap material limitations and providing a medi­um conducive to plant growth. The bench scale study also pro­vided insight for the future of heap leach planning and design with successful reclamation in mind at the forefront.

Jan 1, 1998

By J. Duarte Neto, V. M. Torres, A. Viana, G. S. P. Pereira, P. M. Andrade

There are technical and commercial limitations to using high fluorine copper concentrates in industrial copper smelters. The presence of more than 1,000-ppm fluorine affects the sulfuric acid units generally integrated to copper smelters. Price penalties are normally applied to copper concentrates with high fluorine contents. Several process alternatives to resolve this issue were studied at the Companhia Vale do Rio Doce (CVRD) Technology Center, Santa Luzia, Brazil. These alternatives included modifications to conventional sulfuric acid plants so that they can use high fluorine concentrates; removal of fluorine-containing minerals by flotation using depressants; selective leaching of fluorine minerals; and sulfuric acid leaching of the copper concentrates. As a result of this research, a hydro¬metallurgical process to remove fluorine and upgrade copper concentrates was developed by the CVRD.

Jan 1, 1999

By John T. Crawford

Open pit limit analysis techniques of various types have been utilized for many years to design ultimate pit surfaces. In the last 15 years there have been many advances in the development of sophisticated computer methods to aid this process. The extensive capability of the computer has led to multiple alternative approaches to problem solving. Computerized open pit limit analysis methods can be applied to a broad scope of long-range and intermediate-range mine planning and design questions. A single computer run develops a pit design from a set of data. A set of nonsequential runs is used to evaluate changes in pit slopes, property restraints, and mineral model variables. Ore reserve economic sensitivity and intermediate-range mining plans can be developed using sequential computer runs. Present value methods are incorporated by using iterative sequential techniques. Multiple ore processes, dump leaching credits, and the trade-off between open pit and underground mining can also be handled. Many of the applications described are representative of current practice. The remainder are suggested extensions.

Jan 1, 1979

By Jerry Dolph

Hecla Mining's Lucky Friday Mine, located beneath the town of Mullan, ID, has been shaken since the 1960s by many deep underground rock bursts. The largest rock burst carried a magnitude of 3.5 on the Richter Scale. It occurred in 1969 when all of the stopes on a level approached an upper level at the same elevation. After that, a stair-step pattern was used to give the mine's levels more of an "arch." The article is an account of one of the more ferocious bursts to hit the miners of the Lucky Friday. I say "miners" instead of "mine" because I was there and it was a very personal experience for me. I had been working at the Lucky Friday for six years. During that time, I had heard and felt thousands of air blasts. In fact, in the early spring of 1986, the mine was experiencing as many as 1000 air blasts an hour, of different intensi¬ties, of course. Most of them sounded like popcorn popping. There were also a few bumps and occasionally a real boomer. That day did not seem any different

Jan 1, 1994

By Steven W. Hunt, Phillip U. Santacroce, Roger C. Ilsley

Consolidation grouting from the surface prior to mining a shaft is commonly performed to reduce groundwater inflows to a manageable rate. This paper describes the inflow reductions obtained within dolomite and limestone formations at several shafts and chambers due to grouting programs for the Milwaukee Water Pollution Abatement Program. The resulting inflow reduction factors are compared to results reported in the literature for other projects. Post-grouting pump tests are also evaluated as an aid in grouting assessment. Important considerations for estimating shaft inflows from pump test results are discussed. These considerations include loss of grouted mass during mining and influence of blasting and rock features on grouting effectiveness. This information should be helpful to design engineers and contractors who need to estimate inflows after pre-excavation consolidation grouting has been performed.

Jan 1, 1993

By David B. Ashley

Risks in underground construction are often viewed as technical in nature; "running ground, " "squeezing ground" and "chimneys" are terms that appear in construction managers' nightmares, and occasionally in their underground projects. Financial consequences of these and other project risks are reviewed. Special attention is paid to sources of cost overruns. From this study a structure evolves for setting priorities for risk management actions; these actions can also be tested for impact and potential effectiveness. Finally, case study reviews of six underground projects indicate the "state of the practice" for financial risk management.

Jan 1, 1983

By J. R. Blair, D. P. Lindroth, W. R. Berglund, R. J. Morrell

The objective of this US Bureau of Mines (Bureau) research was to determine the technical feasibility, principles and effectiveness of a combination energy method for drilling and cutting hard rocks. Experimental test results of microwave heating and drilling in basalt and granodiorite are given. The experiments were performed with pilot-scale, commercially available equipment employing microwave energy at a standard industrial frequency of 2.45 GHz. The data indicate that penetration rates, well in excess of the state of the art, are possible.

Jan 1, 1993

By R. Torbin

The degree to Which automation/remote control/robotics has been utilized in the mining industry is far less compared to general industry because of several factors. These factors include the adverse working environment, the difficult work operations, and the generally lower incentive for capital investments in new mining equipment. Foster-Killer has been actively involved in the development of advanced mining and underground construction equipment. This equipment is designed to be remotely operated to improve both productivity and worker safety. Many of these machines employ advanced electronics and robotic features. Other types of Foster-Miller developed robots will also be described Which could be applied to special mining problems. The types of machines that will be discussed include the following: remote shaft lining/placement. remote excavation/mining operations, automated conveyor system, and robotic surveillance.

Jan 1, 1989

By Danqing Xu, A. W. Khair

This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.

Jan 1, 1991

By Harold E. Goetzman, Blair R. Benner, Shaolin Zhong, Rodney L. Bleifuss

A commercial high pressure roller press (KHD 90125) was installed at the Coleraine Minerals Research Laboratory for testing in October, 1994. Pilot plant evaluation of the high pressure roller press has shown that it can be used as an alternative to the rod mill for the comminution of taconite. A series of pilot plant tests were run to compare roller press products to rod mill products in a simulated taconite flowsheet using magnet separation and closed circuit ball milling. Further investigation of a hybrid grinding system, roller press crushing followed by ball mill grinding, indicate that the combination may represent the most energy efficient system for taconite processing.

Jan 1, 1998

By L. Lichty

Treatment of refractory gold ores containing arsenic has always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries and production of hazardous fumes, effluents and residues. Due to these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processes for refractory gold ores and concentrates have been explored. A few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180° to 200° C or 356° to 392° F) and pressures (2.75 MPa or 400 psi) is accompanied by high capital and operating costs.

Jan 1, 1990

By Harrie van Dijk

Feeding laterite nickel slurry into high pressure acid­leach (HPAL) autoclaves in an aggressive environment with slurries heated up to 200°C requires a special pump design. For decades the GEHO piston diaphragm pumps have been used for autoclave feeding at gold ore pressure oxidation plants with slurries up to l 77°C. Lessons learned from these installations have been instrumental in designing second generation feed pumps for processing laterite nickel with operating temperatures of 200°C and a flow rate of 400 m3/h. The Australian nickel industry is using momentarily 8 GEHO positive displacement piston diaphragm pumps. For this application six GEHO ZPM 900 "dropleg" pumps have been supplied to the Murrin Murrin project and two to Bulong.

Jan 1, 2000

By R. Z. Pyrih

Uranium tailings at Cotter Corporation's Canon City, Colorado Mill were moved to a double-lined impoundment, but uranium and molybdenum salts remaining in the fractured bedrock underlying the old tailings ponds seeped into groundwater. Fluor Daniel GTI recommended an in situ geochemical fixation remedy, flushing Best Sulfur Products' calcium polysulfide reductant into the subsurface with clean water. Residual metals became immobile, trapped in the bedrock. Fluor Daniel GTI designed and implemented the process on ten acres with high metal concentrations. Cotter is operating and monitoring the system, which can be expanded to "hot spots." The original remediation time was estimated at less than five years.

Jan 1, 1998

By Dr. -Ing. Karlheinz Timtner

This paper deals with the complicated and often misunderstood relationship between torsional windup, load sharing and peak torques in conveyor backstops. The principals apply in low speed, intermediate speed or high speed applications. Once the controlling factors are understood, a reasonable approach to selection procedures can be achieved.

Jan 1, 1996

By Ernest L. Ohle

Since the first recorded discovery of lead in southeast Missouri near Fredericktown about 1720, knowledge of the deposits has advanced in spurts as a result of outlying discoveries: 1864 Bonne Terre 1890 Flat River, Desloge, Leadwood 1948 Indian Creek 1955 Viburnum The original discoveries at Bonne Terre consisted of residual galena in clay, similar to that in the previous finds at Fredericktown. Occurrences in solid dolomite were not noted until mining of the clay pits exposed the walls of the weathered depressions. The St. Joseph Lead Co. had been established to conduct the operations and it was J. Wyman Jones, first president of St. Joe, who at that time brought about the first of the technological advances that were to occur in the district. He proposed use of the newly invented diamond drill to explore the bedrock showings, after observing the machines in the Vermont Marble Belt.

Jan 1, 1991

By Michael J. Virnig, Murdoch W. MacKenzie, Michael R. Davis

The objective of this paper is to present preliminary capital and operating cost estimates (±25%) comparing conventional carbon-in-solution (CIS) with resin-in­solution (RIS) using AuRIX® 100 for the recovery of gold and silver from typical heap leach solutions. Preliminary testwork was carried out with AuRIX® 100 using real and synthetic leach solutions to determine the technical viability of the resin for gold/silver recovery and to provide process design parameters for the preliminary RIS circuit. The scope of the resin testwork was sufficient to support the level of accuracy applied in the capital and operating cost estimates. No parallel testwork was carried out with activated carbon. Industry standard design data and operating data from existing CIS operations were used as a basis for the comparison. Both the capital and operating cost comparisons indicate a substantial savings for a RIS circuit using AuRIX® 100 (- 14 to 18% in terms of capital and 25 to 35% in terms of operating costs) over a conventional CIS circuit depending upon solution flows and grade.

Jan 1, 1999