Search Documents

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By S. A. Osterberg, J. L. Breckenridge, R. S. Popielak

Multidisciplinary investigations were completed to prove the availability of water resources for the proposed San Cristóbal silver-lead-zinc mine in the arid Altiplano of Bolivia. Surface water resources are scarce, of poor quality, and unsuitable for development. Therefore, hydrogeological reconnaissance targeted alluvial aquifers for development. Follow-up resistivity, refraction, and water quality assessments were used to prioritize areas with prolific production potential. Pumping tests and regional water balance analysis indicate an alluvial aquifer can sustain the required approximately 40 000 m3 per day production for the life of the mine and predict no significant negative environmental effects on local groundwater users and the environment.

Jan 1, 2002

By Douglas Banks

Construction for the new 2.5 MGPD raw water intake project commenced December 2002. The project, initially designed as a 12' Ø concrete lined intake shaft,145' deep, with two offset 24" lake taps, 520' and 470' long was subsequently “value engineered” running the two lake taps through a single conduit. The offset for summer and winter pools was accomplished via a second shaft located at the lakes edge. Construction involved the use of blind drilling techniques for the shaft development and drill and blast techniques for the tunneling. All works were completed through extremely hard crystallized sandstone. The project came online August 12, 2004.

Jan 1, 2005

By Donald E. Garrett

Sodium sulfate is one of the larger tonnage industrial minerals. A little more than half of this tonnage — 3 Mt/a (3.3 million stpy) of natural product— is recovered from ore deposits. Most of the rest is produced as a byproduct from other manufacturing operations. Sodium sulfate is mined in a variety of ways. These include conventional room-and-pillar mining, strip mining, in situ leaching of thick ore beds, solar evaporation and cooling-crystallization of lake brine, and the pumping of brine from complex salt deposits. There is also a variety of commercial sodium sulfate ore sources. They include thenardite (the mineral form of sodium sulfate, or Na2SO4), mirabilite (glauber salt,Na2SO4•10H2O), glauberite (Na2SO4•CaSO4), astra-kanite (bloedite; Na2SO4•MgSO4•4H2O), burkeite(2Na2SO4•Na2CO3), sodium sulfate-containing caliche and various brines.

Jan 1, 2002

By Willard C. Lacy

INTRODUCTION A program to insure adequate talent for development and management of our mineral resources entails two equally important and interrelated aspects: 1) attracting and retaining promising student talent, and 2) providing a first-rate education for those entering careers in mineral science and engineering. Manpower shortages have eased in many areas of engineering, particularly in those areas dependent directly or indirectly upon government contracts in space and war programs. However, in the minerals industry the needs still remain critical. As increasing concern over preservation of the environment has developed, the political and social reaction was to seek out major offenders, to look for "whipping boys" -- and the mineral industry was, and had been, an offender. It was there for everyone to take pictures, it couldn't be covered up, and the Department of the Interior lashed away in the beautiful and popular brochures: Quest for Quality, The Third Wave, The Population Challenge, and Surface Mining and Our Environment (Ravaged Land). The Sierra Club, the Field and Stream magazine, TV, and daily news media added their lashes. In the minds of our social-conscious youth the mineral industry took on the image of "exploiters" of natural resources; "polluters" of streams, lakes, and the atmosphere; "despoilers" of wilderness areas and scenic beauty -- a plague to combat, rather than an exciting challenge that entailed exploration of the remote, conquering of the primitive, and developing of the undeveloped. Enrollments declined and many traditional mineral engineering curricula were abolished or Integrated into other stronger engineering departments to meet student-faculty ratio requirements.

Jan 1, 1971

By Ezz El Din Abdel Hakim Khalaf, Khalid S. Essa, Marc Munschy, Mohamed A. S. Youssef

This study focused on joint interpretation of the aeromagnetic and radiometric data to allocate and describe the structural elements and mineralization zones such as uranium, gold, and sulfide in the Gebel Umm Tineidba and its surroundings, Eastern Desert, Egypt. The study region is covered by exposures of Precambrian rocks such as gneisses, migmatites, ophiolitic mélange, metavolcanics, younger granites, and Quaternary sedimentary covers. The application of the total intensity magnetic and reduced-to-pole maps, power spectrum, analytic signal, tilt-angle, and local wavenumber maps helps in recognizing magnetic sources distribution, lineament features, and mineral zones delineation. The obtained results indicate that the depths of the deeper NE–SW, NNE–SSW, and N–S trending structures extend from 400 to 1750 m and shallower ones range from 100 to 400 m. Finally, the main trends of these structures affect the probable mineralization zones.

Sep 22, 2022

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago there were only a small number of projects that stretched beyond 100,000 Mtpd throughput rates. Nowadays and moving forward virtually all the major copper projects are sized beyond this, with throughput rates up to 250,000 Mtpd now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 flotation cells, through to the 257 m3 cells and nowadays to the 660 m3 machines. The contributions of specific copper concentrators to this growth phase are reviewed herein. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 27, 2013

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008

By Wojciech Klecan

Cobb County, located on the northwest side of Atlanta, GA, is continually growing and, like many other metropolitan areas, it needs to increase the capacity of its waste water system to meet future demand. The Cobb County Water System (CCWS) is the responsible agency for water distribution, waste water collection and treatment in most areas of the county. CCWS, one of the most progressive agencies in the metro-Atlanta area, is addressing its future waste water capacity needs in the southern part of the county with the construction of the South Cobb Tunnel and Pump Station. This project consists of an 8.8-km- (5.5-mile-) long, 8.2-m- (27-ft-) diameter, tunnel boring machine (TBM) excavated waste water storage and conveyance tunnel; six tangential vortex-flow intakes ranging from 1,533 to 5,700 L/s (35 to 130 mgd) peak flow capacity, two construction shafts, six 1.8-m (6-ft) finished diameter connecting tunnels ranging in length from 6 to 975 m (20 to 3,200 ft) and a 5,700-L/s (130-mgd) wet/dry pit pump station. The pump station will have a semi-circular wet well with a dividing wall that extends almost to the top of the shaft and a spilt dry well for reliable operation. Roller gates will control the flow to the wet well from the tunnel. The pump station will have six 1,420 L/s (32.5 mgd) pumps and two sets of stair wells and elevators. With a finished diameter of 32 m (104 ft) and a depth of 62 m (204 ft), this is the largest pump station shaft constructed so far in Georgia for the dewatering of a waste water tunnel. The pump station shaft was also the highlight of the well attended and successful 2009 Shaft Design and Construction Short Course held in Atlanta, Sept. 10-11. The two-day course was sponsored by the Underground Construction Association of SME and Pennsylvania State University and concluded with a field trip to the pump station shaft. The tunnel starts south of the city of Austell and finishes at the South Cobb Water Reclamation Facility (WRF), located on the banks of the [ ] Chattahoochee River just north of Interstate 20 (Fig. 1). The South Cobb Tunnel will run 30 to 137 m (100 to 450 ft) below the surface, with an average depth of about 91 m (300 ft), through metamorphic rocks (Fig 2). The construction contract was awarded to Shea-Traylor JV with the lowest bid price of $305 million and notice-to-proceed was given on July 14, 2008. Jordan Jones & Goulding, Inc. (JJG) is the project designer and performed the geotechnical investigations. Parsons/Jacobs Associates is the construction manager. The South Cobb Tunnel is CCWS?s second deep hard rock tunnel. The 15.3-km- (9.5-mile-) long, 5.5-m- (18-ft-) diameter TBM excavated the Chattahoochee Tunnel was the first deep tunnel to be construced in Cobb County. Construction began in 2000 and the project was completed four years later. It is located about 16 km (10 miles) northeast of the South Cobb Tunnel in similar geology. It was designed by JJG to meet east Cobb?s long-term waste water capacity needs and provide flow equalization to the R.L. Sutton WRF. The Chattahoochee Tunnel was named ?Outstanding Civil Engineering Project of the Year? by the Georgia Sec-tion of the American Society of Civil Engineers in 2006.

Jan 1, 2009

By P. K. Parhi

The extraction of nickel has been carried out by the hollow fiber membrane technique using D2EHPA as the mobile carrier from the manganese nodule leach liquor after separation of Cu(II), Zn(II) and Co(II). The experiments were designed according to central composite design (CCD), which is a response surface methodology. The process parameters used for the experimental design were: pH, concentration of D2EHPA in the membrane phase, flow rate and H2SO4 concentration in the strip solution. Based on the analysis of variance, a reduced quadratic model was found to best fit the experimental data. The process parameters were optimized to maximize the nickel flux and the optimized conditions were flow rate: 630 mL/min; pH: 6.37; D2EHPA: 1.15 mol/L (1,150 mol/m3) and H2SO4: 2.39% (430.2 mol/m3), for a maximum nickel flux of 7.08 x 10-5 mol/m2.s, which was in good agreement with the actual Ni flux of 6.99 x 10-5 mol/m2.s.

By E. O. Mixon, Jack D. Kennedy

INTRODUCTION This contract is the most northerly portion of the Metropolitan Sanitary District of Greater Chicago's Tunnel and Reservoir Plan. (TARP) The project begins at Addison Street in Chicago and proceeds northerly approximately ten miles to end at Wilmette Harbor and Lake Michigan. The project which consists of 2 work shafts, 32 drop shafts, 7.322 km (24,020 ft.) of 6.7 m (22 ft.) diameter circular rock tunnel, 8.458 km (27,750 ft.) of 9.2 m (30 ft.) diameter circular rock tunnel and miscellaneous rock bolting and grouting, was bid for a total cost of $63,140,480. The tunnel invert elevation varies from 65.5 m (215 ft.) to 77.4 m (254 ft.) below the ground surface, which places the tunnel in a rock formation of dolomite limestone. At the tunnel invert, the unconfined compressive strength of the limestone varies from 96 MPa (14,000 psi) to 152 MPa (22,000 psi). The 6.7 (22 ft.) diameter tunnel required the mining of 10.9 cu m. (14.2 cu yd.) of rock per lineal foot of tunnel while the 9.2 m (30 ft.) diameter tunnel required the mining of 20.1 cu m (26.3 cu yd.) of rock per lineal foot of tunnel. The total cubic meters of rock required to be excavated from both tunnels was 818,821 cu m (1,070,978 cu yd.). All of this will be mined by tunnel boring machines (TBM). These tunnels were not to be lined with concrete. The thirty two drop shafts have upper portions that are cylindrical in the overburden and rock sections. They were divided into two groups, depending on diameter, with a different construction method for each group. The first group consisted of twenty three of the

Jan 1, 1979

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By Martin Herrenknecht

The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge to provide efficient traffic infrastructure, such as a modern public transportation system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are also essential. Additionally, supra-regional transportation routes such as long distance water diversion schemes are the challenges for the future. All these projects are as demanding as they are characterized by a tight time schedule.

Jan 1, 2010

By Clayr Alexander

Stillwater Mining Co. (SMC) is engaged in developing, extracting, processing and refining palladium, platinum and associated metals (PGM)from the J-M Reef. This geological formation is located in Stillwater, Sweet Grass and Park counties in southern Montana. Associated byproduct metals include rhodium, gold, silver, nickel and copper. SMC’s current mining operations are near Nye, MT. The company is currently developing a second underground palladium and platinum mine, the East Boulder project, about 21 km (13 miles) west of the Nye operations. A 5,650-m (18,550-ft) tunnel is required to gain access to the ore-bearing horizon (J-M Reef).

Jan 1, 1999

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By J. A. L. Campbell

The Galatia Mine is a dual-seam underground coal mine located in Saline County, IL. In 1984, it became the first coal mine to be permitted by the Illinois Department of Mines and Minerals to operate diesel equipment underground. And it is one of the larger underground coal mines in the nation to use diesel equipment. From the beginning, Kerr-McGee determined that diesel equipment offered the best approach to the safe and productive development and operation of the Galatia Mine. The flexibility of this equipment and its ability to promptly respond to changing conditions and mining locations made its use desirable for building this large dual-seam coal mine. The mine had a planned nominal annual capacity of 3.6 Mt/a (4 million stpy) and would employ more than 500 people. Galatia's current reserves are estimated at 231 Mt (255 million st) of recoverable coal from two seams of high-quality, high-volatile bituminous coal. The Harrisburg No. 5 seam is shipped primarily as a low-sulfur steam coal or as a metallurgical blend stock. It is also used in the pulverized coal injection (PCI) process for steel making. The Herrin No. 6 seam is a medium-sulfur coal. Annual production is shown in Fig. 1. A good indicator of a mine's success is employee productivity improvement. For many reasons - the proper use of diesel equipment, the introduction of longwalls and increased employee ex¬perience - Galatia employees have achieved a steady growth in annual productivity (Fig. 1) while maintaining an exceptional safety record.

Jan 1, 1993

By James D. Nickerson

Thee Brightwater water treatment facilities, currently scheduled to be completed in 2010 and begin operating in 2011, will serve the northern part of King County, WA. The facility includes a new treatment plant and extensive conveyance system consisting of more than 21 km (13 miles) of influent and effluent conveyance tunnels and five portals. The majority of the conveyance system tunnels are mined by tunnel boring machines (TBM) and microtunnel boring machines (MTBM). Tunnel and portal construction is divided into three main contracts. The Ballinger Way receiving portal, constructed under the central tunnel contract, is the terminus for the BT-3 leg of the central contract and the BT-4 terminus of the west contract. The shaft has a 7.3-m (24-ft) finished inside diameter (ID) to accommodate removal of the central project TBM and the west contract TBM and extends to a depth of 66 m (216 ft) below grade through a complex and challenging soil profile characterized by multiple ground water tables. Vinci Grand Projects/Parsons/Frontier-Kemper Constructors (VCFK) was the joint venture team for the Ballinger Way portal. Frontier-Kemper was responsible for the shaft sinking. VCFK evaluated either slurry wall techniques or ground freezing for earth support during excavation of the portal and liner installation. The selection process took into account the vertical depth, cost, past practice, geology, water tables and a 9-m- (30-ft-) thick zone of contaminated soil at the top of the shaft. Ground freezing, which would also act as a hydraulic barrier, was deemed the better option for this project. The contract was awarded to New Jersey-based geotechnical contractor Moretrench. Typically, frozen walls, by design, key into an underlying cutoff. At the Ballinger Way portal, however, the [ ] freeze bottomed out in a substantially thick stratum consisting of predominantly clay, but with some inclusions of permeable soil that indicated significant ground water pressures. To ensure stable conditions at the bottom of the shaft, Moretrench, which also specializes in dewatering, designed and installed a perimeter array of deep wells to temporarily depressurize the permeable soils. The movement of ground water generated by pressure

Jan 1, 2009

By Hassell E. Hunter

The Wyoming Mineral-Conoco Crownpoint Project represents the first time that big hole drilling has been exclusively used to develop totally a privately financed mine below a depth of 1000 feet. Three shafts, one ten feet in diameter and two six feet in diameter, were successfully drilled to depths of 2243', 2188' and 2188' respectively and cased with hydrostatic designed steel casing. The largest shaft is to be used to handle muck and water from station excavation and enlargement of the other two shafts. A reverse circulation system with potassium chloride base mud was used for drilling. The mud was cleaned by settling in steel lined tanks with assistance by cyclone type separators. Deviation was monitored by gyroscopic surveying at 30 foot intervals and did not exceed 16 inches off plumb. Casing was designed to withstand hydrostatic pressures with a 1.5 safety factor to the large shaft and 1.25 safety factor for the smaller shafts. All casing welds were x-ray tested prior to lowering the casing in the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1983

By Brendan Demich, Linda L. Chasko, Brendan Macdonald, Timothy J. Orr, Jessie J. Mechling, Cassandra Hoebbel, Jason Navoyski, William Helfrich, Jessica Cohen, Paul E. Schmidt, Jennica L. Bellanca

The National Institute for Occupational Safety and Health (NIOSH) in partnership with the Mine Safety and Health Administration (MSHA) developed VR Mine Rescue Training (VR-MRT). It is a training platform that allows mine rescue team members to explore virtual emergency scenarios collaboratively. Team members use a head-mounted display to visualize and interact together with equipment, hazards, and dynamic ventilation. All player actions are recorded and displayed for debriefing. Researchers at NIOSH demonstrated the training platform at various mine rescue competitions, including the International Mine Rescue Competition, and collected feedback. Participants’ responses were overwhelmingly positive. This paper describes the development of the software platform and the results of the usability surveys and interviews.

Jun 25, 2023

By V. L. Franzen, Z. J. Hladysz, C. A. Kliche

The Wharf Resources mine, located in the Bald Mountain Mining District approximately 6.4 km (4miles) west of Lead, South Dakota, has operated a surface gold and silver mine and heap leaching processing facility since 1983. Wharf Resources intends to mine and process gold and silver ore from the Wharf Expansion area which is located on the eastern flank of the currently permitted Foley Ridge Mine. The Trojan Pit for the Wharf Expansion area was initially designed with an overall highwall slope angle of 45o. During mine permit presubmission meetings with personnel from the SD Department of Environment and Natural Resources (SD DENR), the question arose as to whether a detailed slope stability analysis of the proposed Trojan Pit highwalls was completed to justify the 45o slope. Wharf’s response was that the highwall design was based, in part, upon studies completed in1987 on the Annie Creek and Foley Ridge Mines; and, in part, upon subsequent slope stability analyses conducted by Wharf mine personnel through 1996. It was suggested by the SD DENR that the stability study be updated to reflect structural geological conditions in the Wharf Expansion area.

Jan 1, 2000