Search Documents

By R. L. Grayson

Compliance standards for respirable dust, which are reduced because of high quartz concentrations, have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coalmine dusts indicates that they mine exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. If, however, the quartz is locked inside another material matrix or coated, a reduced compliance standard may not be appropriate.

Jan 1, 1992

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By Neil J. Duncan, Edward R. Langfield

A hydraulic rock breaker was developed in Germany by Helmut Darda and uses a wedge-plug and feathers mechanism powered by a 10,000 p.s.i. power pack. During the past four years these tools have been increasingly used all over North America for secondary breaking of boulders and rock. More recently, techniques have been developed to break rock off the solid in trenches and rock emplacements where blasting is pro¬hibited or very limited. Underground operations are commencing to adopt the splitter for scaling plus including systems which can be efficiently applied to chambers and mines. Mr. Neil Duncan, who was originally scheduled to give the main part of this presentation has, during this past month accepted a position with the Alberta Energy Resources Conservation Board in Calgary. The board encourages its members to take part in seminars such as this but, unfortunately, due to the heavy pressure of work, it was impossible for him to attend this conference. Mr. Duncan has, however, forwarded me his notes and suggest¬ions, and using these, combined with a slide presentation, we feel that we can quickly and clearly define the operations and application of the hydraulic splitting technique as it applies to your profession and tunnelling work. The first question that most of you are asking is, "Why use a hydraulic splitter if you can blast?" Our answer to this is that we are not advocating the use of hydraulic splitting where blasting is feasible - but, during the past decade many applica¬tions have arisen where blasting is not allowed, or restricted

Jan 1, 1997

By J. K. Neathery, T. X. Li, H. Ban, J. M. Stencel, X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods. We report on the upgrading of molybdenite ore using a laboratory-scale, drytriboelectrostatic beneficiation system. This system employs pneumatic transport conditions to tribocharge, beneficiate and collect the fine molybdenite ore particles. Using this system, two Mo ores were beneficiated under dry conditions without the addition of water or surface modifiers and additives. Beneficiation performance was dependent on the particle size of the feed ore. The surface and particulate morphology and elemental concentrations in the parent feeds and the beneficiated products were examined by scanning electron microscopy (SEM) and optical microscopy. These data, in conjunction with a complete recovery analysis, define some potential advantages of dry, triboelectrostatic beneficiation processing and provide insight into factors controlling molybdenite ore upgrading.

Jan 1, 1999

By Pierre Mousset-Jones

I wish to submit this discussion item on an article published in the August issue of MINING ENGINEERING by Wala and Altman on the use of canonical diagrams for mine ventilation networks. The advent of computer graphics and plotting has enabled complex underground mine layouts to be displayed and plotted in a variety of three-dimensional formats that very closely represent the actual mine layout. This enables the ventilation engineer, who is familiar with the mine, to display the network pressures, quantities, resistances, and fan locations in a way that can be understood by everyone working at the mine. This is important if the ventilation engineer needs to discuss changes in ventilation with production personnel, or escapeway procedures with union personnel. While I can see some of the potential advantages in the canonical ventilation network diagram described by Dr. Wala, it appears to me that the fact that the diagram has no visual equivalence with the actual mine layout means that most mine personnel will find such a diagram almost incomprehensible. The authors have alluded to certain advantages with the canonical diagram. However, I find it difficult to see that these outweigh the fact that almost everything listed can be duplicated in isometric diagrams, and in a manner that is easily understandable to everyone in the mine from the miner to the mine manager. Perhaps the authors could show a clear example comparing an isometric with a canonical portrayal of a mine network showing the information that is immediately available from the canonical network that is not obvious in the isometric diagram. There is in this country a severe problem with the need for ventilation engineering and expertise to be used and accepted by mine management as a necessary part of mine planning. It seems to me that to introduce the requirement for further explanation so that management can understand a canonical network display will hinder more than help the recognition that ventilation engineering needs at so many mines in this country. However, I can see that the canonical approach does have its place in assisting the practicing mine ventilation engineer, wherever he or she exists in the organization chart for a typical mine. In this case, could the authors please indicate the availability of the computer program to compute and plot the canonical diagram for a mine ventilation network.

Jan 1, 1990

By Ivor Hawkes, Malcolm Mellor

INTRODUCTION There are currently around fifteen companies in the United States and Europe manufacturing hard rock tunneling machines. In recent years upwards of 200 hard rock tunnels of lengths up to 12 miles and diameters to the order of 30 ft have and are being successfully driven by over 100 different machines. It has been predicted that within the next decade over 2,000 miles of tunnels will be driven for transportation purposes in the United States alone (OECD Advisory Conference on Tunneling, Washington, 1970) and it is expected that eventually most tunnels including mine drivages will be excavated by machines. All tunneling machines have certain common basic functions; thrust is applied to drive or hold the rock cutting tools into the face, and torque is applied to rotate the cutting tools over the face so that they can continuously break out rock. The speed of head rotation, together with the torque requirement, determines the cutter head power. (The power required to push the head forward is usually negligible.) There are many factors which determine how successfully a given tunneling machine will perform in a given rock but one of the most important is effective utilization of cutter head power. This paper is a review of the specifications and performance of hard rock tunneling machines, obtained from manufacturers' catalogs, published literature, talks with manufacturers and visits to operating machines throughout the United States and Europe.

Jan 1, 1997

During the past decade, international mining companies have descended on South America. Countries like Chile, Brazil and Peru have seen billions of dollars in exploration and development funding turn their once meager mineral industries into mining giants that have become the envy of the world. Part of this outpouring of foreign investment in those countries has been because each has privatized its state-owned mining companies and has liberalized its foreign investment laws. In addition, they have rewritten their mining codes to encourage minerals development and passed new tax laws that have made natural resource development more attractive. Now these same international mining companies are turning their attention to Argentina. This a country that, like Chile, Brazil and Peru, has a wealth of largely un- tapped mineral resources. And Argentina wants its share of the foreign investment that its neighbors have enjoyed. With that in mind, ministers of Argentina's natural resource agencies came to Denver, CO to meet with mining executives and pitch their country's mining industry. The meeting, attended by about 200 people, was sponsored by the US Trade and Development Agency and organized by the World Trade Center Denver. Others involved were the Colorado Mining Association, the Colorado International Trade Office and the Secretariat of Industry, Commerce and Mining of Argentina. The following is a summary of a report on Argentina's mining industry. It was prepared by Anderson & Schwab Management Consultants and distributed to attendees as part of the meeting's program.

Jan 1, 1998

By Jianguo Hao, Qingbiao Zhao, Bingnan Hu, Shimin Fan

The paper makes a systematic analysis of interaction between backfill and pillar in coal mining. It compares the difference of pillar strength with backfill and without backfill. It is proved that there are the obvious improvements in pillar strength and the decrease in subsidence. It discusses the subsidence effects of different extraction ratio, different backfill ratio, and different elastic modulus ratio in details. The paper analyses the sensitivity by orthogonal test method. At last, author proposes some suggestion to increase pillar strength, to reduce subsidence, and to guide engineering practices.

Jan 1, 2001

By S. K. Kawatra

Although temperature is known to have a substantial effect on many processes, this parameter has been widely dismissed as insignificant for mineral comminution. For this reason, temperature effects on grinding have largely escaped notice. However, it has been observed that processing plants which are subjected to large seasonal temperature variations show a change in performance which appears to be due to changing feed temperatures. The general effect is an increase of the specific energy consumption as the temperature decreases. In autogenous mills, an increased rate of production of critical-size material has also been observed. This is due, at least in part, to changing rheological conditions in the mill, with the slurry viscosity increasing markedly at low temperatures. Mechanical changes in the rock with temperature, such as increased brittle fracture, is also responsible for a portion of the observed seasonal effect, and may account for this phenomenon being observed only in certain plants.

Jan 1, 1989

By G. Capello

Carboniferous mining basins are today a non-negligible source of energy. So important in fact that returns now justify high investments and costs even for those deposits that were un-economical in the past. Nowadays, if properly explored and exploited, basins previously considered non-minable due to complex structural and stratigraphical situations may be economically interesting. It is while studying a faulted basin with such features that the Authors developed the described computer-aided methodology capable of constructing a model of the physical structure of coal deposits on the basis of stratigraphical data from drillings. The aim of the procedure is to define coal reserves, the exploitation of a deposit being conditioned by the possibility of identifying zones that are technically minable. This objective is pursued by making as detailed a reconstruction as possible of the geometrical, stratigraphical and tectonic features of the coal-bearing seams of a deposit.

Jan 1, 1982

By Deepak Malhotra, Sean Armstrong, Linda Baltich

The economic profitability of any mineral company is dependent upon maximizing mineral recoveries while minimizing costs. The effectiveness of any strategy to meet this objective is dependent upon firstly obtaining quantitative information concerning the steady-state metallurgical balance of the plant, and secondly, how efficiently this information is used to improve/optimize plant performance. This two-step approach can be designated as a "plant audit." Plant audits on a routine basis can be very expensive and time-consuming. Most plants have reduced staffs to cut costs. The remaining staff has to spend time to solve production/operation problems, thereby leaving limited resources (i.e., people, time, and money), for plant auditing. This paper briefly reviews plant auditing categories, and a systematic approach to auditing which has been successfully used at several operations. An example illustrating the use of this approach in gold operations is discussed in this paper.

Jan 1, 1992

By Bela Koman

Abstract - A shiploading terminal near Punta Arenas, the southernmost city of the world (lat. 53°-10'S, long. 70°-54' W) is described. Strong winds, choppy seas, frequent gales, rain, and snow make it difficult to load ships at an offshore berth in this area. Detailed site investigations, including a wind-recording program, supplied sufficient information for the analysis of operating conditions. The weather pattern of the entire region, including the predictability of gales, was utilized in the analysis. The results showed that a bulk loading terminal at this location is feasible, provided that the design takes into consideration the specific problems of the site. The final layout shows a terminal that can be approached from several different directions, depending on the direction of the wind. The mooring system is arranged to allow alter- native ways of attaching and casting off mooring lines and executing docking and departing maneuvers. The berth is supported on piles and contains the minimum of structures, relying on a slewing shiploader to reach the ship in any position, with only limited fore and aft shifting of the vessel for loading the extreme hatches. Results of wind recording, statistical analysis of wind and wave data, operating criteria, and the results of berth availability analysis are included in the paper.

Jan 1, 1987

By Syd S. Peng

Popular concepts of resin and conventional roof bolting The conventional roof bolt with shell anchor was first introduced for coal mine entry support in the late 1940s. The general concept of a reinforcement mechanism for this type of bolt is suspension. This means the shell anchor must be anchored well inside a competent rock stratum (such as sandstone, limestone or firm shale) so the bolt suspends the underlying weaker strata. This concept has and will continue to dominate the use of conventional roof bolts. Under this concept, the conventional roof bolt is not suitable for the stratigraphic sequences in which a strong, firm stratum is not available within the economic anchorage horizons.

Jan 1, 1994

By L. Evrard, M. Van Camp, J. Y. Yen, R. G. Reddy, D. Mantha

Viscosities of two industrial lead blast furnace slags have been experimentally determined as functions of composition and temperature. A Brookfield viscometer with alumina rods and crucibles were used. Experiments were carried out between 1200 and 1573 K in an argon atmosphere with up to 5% addition of FeO, MgO, and SiO2 to the slags. Results showed that 1) the viscosities of two slags decreased with increase in temperature; 2) addition of FeO decreased the slag viscosities; and 3) addition of MgO and SiO2 increased the slag viscosities. Use of the above slag compositions with the addition of FeO is recommended for successful lead smelter operation.

Jan 1, 2005

By Andreas Rubo, Stephen Gos

Over the past couple of decades several endeavours have been made to develop lixiviants with the intention of replacing cyanide in gold leaching. In 1980s these endeavours were largely economically driven, due to cyanide shortages at that time. In more recent times, the driving force has shifted to occupational health and environmental considerations. It is often argued that the high acute toxicity of cyanide alone makes it worthwhile considering to replace it completely by less toxic alternative lixiviants. This has led to having to consider more criteria in the choice of any alternative lixiviants, which have often not been taken into account in the past. The intention of this paper is to review these alternative lixiviants and also review the criteria, which have ultimately led to most of these lixiviants never having found any large scale application, if they passed laboratory stage at all. It is also intended to show, that by handling and treating cyanide in a proper manner, the overall profile for the use of cyanide compared to these alternative lixiviants is very favourable. The question to really be answered is whether there is actually any chemical or process applicable to gold leaching that does not show the high toxicity potential of cyanide and that is still favourable with regard to looking at a broader spectrum of criteria and not only acute toxicity.

Jan 1, 2000

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

By Joseph Corvetti

This paper is of conceptual nature. The authors present their idea of creating an integrated and intelligent excavation design system. Research work has just been started and the results will be addressed during presentation of this paper. The authors are currently engaged in a pilot study and expect to build a feasibility prototype expert system (establishing the numerical-cognitive coupling in excavation design) by the end of this year.

Jan 1, 1996

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By D. Koch

Bentonites and bentonite containing sealing materials are used since many years for sealing purposes in foundation, dike construction, hydraulic engineering and landfill construction, especially for encapsulation of old waste deposits In the near future compacted bentonites will be important components of multi-barrier systems for dry charge of old mines, for underground disposal of hazardous or radioactive wastes. Because of their exceptional physical, structural and chemical properties, bentonites are offering manifold possibilities to protect the environment against the negative effects of dumping grounds. Often the compliance with legal regulations for waste dumping or the isolation of contaminated areas is possible only by using bentonite containing sealing systems. The essential properties of bentonite, bentonite containing building materials and the different techniques of making horizontal technical base liners and vertical cut-off walls are explained. For horizontal technical base liners the adsorption ability, the ion exchange capacity and the swelling behavior of bentonites are important. For cut-off walls bentonite controls the rheological behavior of the slurry and is responsible for the low permeability of the hardened bentonite-cement-wall. In the multi-barrier systems of repositories for chemical or radioactive wastes compacted bentonites are considered to be favourable sealing and backfilling materials because of their high swelling capacity, their adsorption and ion-exchange ability and their plasticity in water saturated state.

Jan 1, 2005

By G. R. S. Smith

In any filtration, it is primarily the filter medium (cloth) and cake filtering properties that control the type of filtration equipment used and filtration conditions. The advent of new types of filter cloths, such as the membrane cloth discussed in this paper, can result in significant changes in filtration techniques and areas of application for filtration. For many suspensions, for instance, conventional filtration is uneconomic compared to gravity separation or not filtering at all (as with product recovery from dilute streams) because the solids are very fine, are hard to retain and build up filter pressure rapidly, and once retained are hard to remove. As a result of the developments discussed here, this is no longer the case. This technique and the use of the membrane filter cloth is well established. This filtration is currently being used for white liquor filtration in twenty-four mills worldwide in the chemical recovery step of the kraft process for producing paper pulp where it is replacing gravity thickeners in new plants. Filters up to 1000 sq. ft. (100 sq. meters) are filtering large volumes of solids from hot caustic solutions. The filtration materials and techniques discussed in this paper open the way to new methods and applications for filtration in the mining industry. It is not the intention of this paper to give a vigorous analysis of the different separations, but to outline some of the ways in which this filtration technique might be used in the mining industry.

Jan 1, 1989