Search Documents

By G. M. Wilemon, Swanton. R. G.

The Bureau of Mines is investigating the leaching of phosphate values from Florida phosphatic clay wastes using sulfuric acid (H2SO4) as the leaching agent and methanol as the solvent. Acid-alcohol leaching studies were done using research-grade apatite to investigate potential causes of flow extractions. It was found that a barrier layer formed on the surface of the apatite. Initial discovery of the barrier layer was made by analyzing pure apatite samples before and after leaching using an optical microscope. Subsequent Fourier Transform Infrared (FT-IR) analyses proved the coating was calcium sulfate hemihydrate (CaSO4•1/2H2O) and that unreacted apatite existed beneath the coating. Scanning electron microscope (SEM) photographs depict the CaSO4• 1 /2H20 morphology as long slender crystals adhering to the apatite surface. It was also shown that grinding the leached tailings and leaching again in the H2SO4-methanol system resulted in additional phosphate extraction.

Jan 1, 1992

By Roger B. Jr. Herbert

Surface water samples were collected from water accumulations at the surface of a neutral pH mine tailings deposit in Kristineberg (Sweden) where algal growth and iron hydroxide precipitates were observed. Ferric iron in the aqueous samples was determined by (adsorptive) differential pulse - cathodic stripping voltammetry. The analyses indicated that labile Fe3+ concentrations were in the range <20 to 337 nM, while total Fe3+ levels were much higher at 0.9 to 8.3 uM. The labile Fe3+ levels are more than two orders of magnitude greater than would be expected based on equilibrium with ferrihydrite. These results suggest that iron complexation with strong ligands in the surface water competes with iron hydrolysis, and that these ligands may be of algal and/or bacterial origin.

Jan 1, 2000

By Y. C. Kim

M.S. Azun The article unfortunately has some serious flaws negating the usefulness of the paper. The authors claim that kriging (linear kriging) is superior to other methods such as polygon. This is not the case. The deterministic methods (referring to polygon, ID, IDS, etc.) should not be compared with the statistical methods (linear kriging, disjunctive kriging, etc.) because they differ not only in their assumptions, but also their tools used in estimation. Thus, they give different results. By comparing the results of deterministic methods and linear kriging, the authors conclude that polygon, IDS, and linear kriging give an average thickness close to the value obtained from realizations. Besides, they argue that linear kriging gives less variance than the others (Fig. 2). The first conclusion is expected, due to the well-known central limit theorem. The second is the result of the statistical properties of different estimators. Thus, the comparison presented in the paper is rather meaningless because the authors have failed to follow basic statistical procedures. The numerical results of different approaches to an estimation problem cannot be generalized. In conclusion, the paper is not a meaningful contribution, and sadly, quite erroneous. Reply by E.Y. Baafi and Y.C. Kim The two key contentions made by M.S. Azun regarding the paper are: deterministic methods should not be compared with statistical methods and, hence, the results are erroneous; and the paper does not make a meaningful contribution. The first contention is an academic one. Most practitioners in ore reserve estimation could care less whether the tool they are using falls under a deterministic or a probabilistic method, so long as it gives the desired answers. It is probably for this reason that, whenever any new tool such as linear kriging is introduced to practioners in the mining industry, they would like to see a comparison test performed between the existing and the more familiar tools with a new and "strange" tool. Only when a new tool passes such a test, the generally conservative mining community would begin to utilize the new tool to its advantage. The second contention, is a subjective one. The final judgment should be left up to the readers within the mining community. If kriging is accepted more among practitioners, partly due to the paper, then the paper makes a practical contribution to the state-of-the art in ore reserve estimation. Finally, M.S. Azun entirely missed two main points in the paper. The first is that any comparative study of kriging vs. Polygonal or IDS should be performed for local estimation and not for global estimation. In the past, kriging was frequently compared with other existing tools in its performance on global estimation. Such results were nearly identical due to the central limit theorem effect, which further prevented the acceptance of kriging by practitioners. The second point is that a single case study using an existing property, as it was frequently performed in the past, is not sufficient because results depend not only on the tool itself, but also on the nature of the mineralization.

Jan 3, 1984

By H. T. Mulryan

Talc is used as an essential ingredient in a variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance and household furniture components to high performance parts made from liquid crystal engineering resins. This paper focuses on polyolefin applications, the three-tier market for talc in polypropylene, the effects of various tales in typical compounds and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds that mimic higher cost resins, and polyethylene films. Customer requirements, for tales for these purposes are discussed.

Jan 1, 1993

By Ashma Singh, Nichole Maistry

Due to declining iron ore grades, low-grade ores with complex mineralogy — namely, banded iron formation (BIF) — are being explored to maximize iron ore resources and increase the life of mine. Flotation is the standard global process used for the beneficiation of BIF ores, as it is a complex ore reserve, and liberation is typically achieved below 1 mm. This study focuses on the flotation of a South African BIF, evaluating its response to different collectors, as well as effect of grind. As flotation is an expensive process and South Africa ranks high on the production cost curve, preconcentration by gravity or magnetic separation is performed prior to flotation. Thus, flotation was also performed on a gravity concentrate to determine if a grade suitable for steelmaking (approximately 63 percent) is achievable. The results indicate that the use of an alkyl ether amine-based collector partially neutralized with acetic acid is suitable for separation of hematite from illite and quartz at high pH values. Further optimization tests are being pursued to improve overall recovery and grade.

May 1, 2025

By Carl Eschman

Productivity from large walking draglines is primarily dependent on operator skills. This machine may be in operation three shifts a day, 364 days a year, and its output is directly related to coal uncovered and mine profitability. Dragline operators must have highly developed manual skills and be knowledgeable in mine planning and working strategies. When using equipment costing more than $25 million, some formal training is usually required before an operator is allowed to assume complete con¬trol; however, dragline operators rarely receive any structured training before operating these giant excavators. A form of apprenticeship is usually followed where an operator candidate progresses from a groundsman to an oiler position. As an oiler, he is permitted to operate the dragline for short periods under supervision. After apprenticeship, the operator is considered sufficiently prepared to operate the largest, most powerful machine at the mine. The apprenticeship training method has obviously provided the surface mining industry with skilled dragline operators; however, conditions are arising that require a realistic and effective training tool that can be accessed by mining companies. New mines -either planned, under construction, or recently opened in the West-do not have access to a pool of experienced operators and oilers as do Midwest mines. As coal mining activities increase in both the West and Midwest, demand for trained dragline operators could be required in a short amount of time. Also, the more productive techniques along with sound basics of strip mining are sometimes lost in the informal "OJT" training method. Modern draglines are the pacemakers of the strip mine, and are simply too expensive to be used as a training device where lost productivity and susceptibility to damage can directly affect mine output. The Dragline Training System is a logical first step in formally educating or retraining operators. The program, started by the US Bureau of Mines and continued by McDonnell Douglas Electronics Co. under contract with the US Department of Energy, was installed and evaluated at DOE&apos;s Carbondale Mining Technology Center in Carterville, IL, last year. It is now being operated by Southern Illinois University at Carbondale. System Description The Dragline Training System addresses specific environments and work practices encountered during an actual mining operation at a midwestern US surface mine. This area was chosen because of its high number of strip mines using large walking draglines. Most draglines in the region are Bucyrus-Erie 1370, 1450, and 2570 models, so the dragline trainer was patterned after the company&apos;s 1370 machine. Operating and emergency controls are sufficiently standardized for most large walking draglines, and peculiar dynamics and responses from any specific dragline can be programmed into the computer system. The computer simply prompts the user to select the manufacturer and any peculiar response or rate changes needed. A 46-m3 (60-cu yd) bucket is simulated, but for closer simulation, various bucket configurations can be provided. Dragline Trainer The dragline trainer uses the TV-model simulation technique. A scaled model of the dragline is positioned in a model mine. A television camera is positioned at the operator&apos;s theoretical eyepoint, and the view captured is projected into a large screen in full scale. The screen is positioned in front of the operator seated in a full-size cab at Bucyrus-Erie controls. By manipulating the controls, the trainee can operate the model dragline and observe its reaction in the television display. In addition to housing dragline controls and consoles, the wooden, oversized cab contains the digital computer, terminal, video recorder and monitor, power switch box, air conditioner, and has enough room for the instructor and five student observers. The 50:1 scaled dragline model contains servo-controlled functions for hoist, drag, swing, delta swing, and longitudinal and lateral position. The delta swing provides bucket lag during swing and a realistic pendulum action when the swing is terminated. The over-responsive second order servo system is designed to provide hoist, drag, and swing rates exceeding present draglines. In all cases, position servos are used for better control and sta¬bility. The normal rate operation of an actual dragline is computed for the specific machine and presented to the servo amplifiers as iterative position commands increasing or decreasing

Jan 6, 1982

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By J. Jeremy Burden, Bruce S. Brown

A major question in the design and permitting of a tailings storage facility is the quality and quantity of seepage which will occur from the base of the tailings facility into the underlying foundation and groundwater regime. A corollary to this is what liner system, if any, is necessary to protect the groundwater regime from unacceptable contamination. Modern tailings storage facilities are generally designed as drained tailings deposits whereby all free water is removed from the facility by decant, drainage and evaporation. This removes the source of on­going seepage and allows for efficient and timely reclamation of the facilities. Quantifying the residual seepage from the base of the tailings deposit is complicated due to the following factors:

Jan 1, 1992

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection systems, the US Bureau of Mines is actively involved in developing a coal rib-thickness monitoring system for high wall mining applications. One particular system that shows promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1996

By J. J. Davis, D. G. Osborne

The Australian coal industry is characterised by efficient fines recovery, and the climate does not dictate the use of thermal drying. With the increasing trend to underground mining and hence finer ROM coal, and market pressures for reduced product moistures, dewatering issues are assuming increasing importance in the Australian coal industry. The greatest potential gains in dewatering performance undoubtedly lie in the treatment of finely sized material. This paper examines the dewatering issues which have been recognised by the Australian coal industry, and describes current Australian research in this field.

Jan 1, 1995

By R. A. Lohnes, S. M. Levorson

As part of research to develop a coal handleability index that predicts the ease with which coal will flow through a handling system, comparative tests were conducted with a Johanson Indicizer and a low-stress triaxial apparatus on 12 coals at a variety of gradations and moisture contents. The lndicizer test provides a rapid method for generating data associated with coal handling characteristics. The arching index measured with the Indicizer is a function of the geometry of the apparatus as well as the properties of the coal. The handleability index determined from triaxial data is a more direct measure of coal characteristics. The handleability index shows a wider range of values than the arching index and, therefore, appears to be more sensitive to coal variations. Neither the arching index nor the ratholing index, as measured with the Indicizer, agreed well with the handleability index. This is attributed to differences in sample preparation as well as to the tests themselves.

Jan 1, 1993

By G. Michael Lloyd

The term phosphate beneficiation often conjures up visions of processing technologies that physically separate the phosphate rock from some impurity and do not result in a change in the chemical nature of the phosphate rock. However, when we consider hydrometallurgical processing as a phos¬phate beneficiation technique we have to include all chemical treatments that convert phosphate rock into a more useful product. With most of the phosphate rock mined being used for fertilizer pro¬duction, the best known and most widely employed hydrometallurgical process is wet process phospho¬ric acid manufacture. In general, all phosphate rocks are so insoluble that there is no physical treat¬ment that will allow the phosphate content to be used by vegetation in a timely manner. However, after chemical treatment, 100% of the phosphate is readily available for vegetation nutrition. If there is a chemical beneficiation process that could be considered the standard method of treat¬ing phosphate rock it would have to be the wet pro¬cess for phosphoric acid production. In this process finely ground phosphate is reacted with sulfuric acid to give phosphoric acid and phosphogypsum. The phosphogypsum crystals are removed from the phosphoric acid solution and discarded; the phos¬phoric acid is further processed to give the finished fertilizer product. The primary reason that this pro¬cess was adopted so widely is because the phosphogypsum solid that is formed can be easily separated from the phosphoric acid, thereby removing the calcium portion of the phosphate rock and the sul¬fate portion of the sulfuric acid. Other acids have been used to treat phosphate rock but nitric acid is the only other acid used commercially. Nitric acid gives a mixture of phos¬phoric acid and nitrates that can be further pro¬cessed into N-P fertilizers, but the range of N/P grades that can be produced is limited. Hydrochlo¬ric acid has been used to react with phosphate rock, and it can be used to generate a pure phos¬phoric acid but only after solvent extraction to separate the calcium chloride from the phosphoric acid. And then there is the problem of what to do with the calcium chloride. The acid that has received the most attention as a substitute for sulfuric acid is phosphoric acid. In this process, the phosphoric acid reacts with the phosphate rock to give a mono-calcium phosphate solution. This process does not dissolve all the impurities in the phosphate rock, and these solids can be removed from the solution before sulfuric acid is added to convert the soluble calcium to insoluble phosphogypsum. Despite all the claimed advantages, this process has not found favor. A suc¬cessful application of this process to treat some of the lower grade phosphate rocks being used today would seem to have some distinct advantages. Other beneficiation schemes have been pro¬posed or practiced on specific phosphate rocks on a limited scale. These include calcination followed by water leaching to remove lime, weak acid

Jan 1, 1999

By Munson R. McKinney, Bryan A. Slim

To date some 1,000 exploration targets (by way of adits, mine dumps, shafts, outcrops and unstoped mine areas) have so far been identified using an interactive data base system to query a digital data base comprising topographic, cadastral geological and mine components developed as a compilation of old plans, records, surveys and recently flown aerial photography. The exploration targets are intended for early follow-up as part of a 1987 exploration programme to investigate the reserve potential of the former producing property located in southern Utah. Of further interest is the unscrambling of old mine plans to provide drill targets for investigation of unstoped reserves with one target being a possible 800,000 tons in part of the lower workings. The project site encompasses about 3,200 acres of mainly patented lode claims covering most of the claims and mines of the Gold Mountain mining district formed in 1889. Turn of the century mining saw several mines operating whose total production was at least 143,000 oz. gold and 460,000 oz. silver from steeply dipping veins up to 20 ft. or more in thickness.

Jan 1, 1987

By R. Hogg, R. H. Weiland, P. Bunnaul

The dewatering of flocculated clay suspensions by compression in a centrifugal field was investigated. The results were analyzed with respect to the direct applicability of centrifugal dewatering (as in solid-bowl centrifuges) and indirect applications to gravity sedimentation systems. An important objective of the study was to evaluate the self-weight effect using centrifugal forces to simulate consolidation of deep sediments. Experiments were conducted in which the sediment mass and initial structure were maintained constant while the effective sediment weight was varied by centrifuging at different speeds. The relationship between the limiting sediment density and the applied consolidation stress was found to be the same for both gravity and centrifugal consolidation, indicating that small-scale laboratory tests can be used to predict consolidation in deep beds. The effects of the initial structure were also studied using controlled variations in flocculation conditions. The results imply that, for the flocculated suspensions studied, the longterm consolidation behavior is relatively insensitive to the actual extent of flocculation.

Jan 1, 1995

By Frederick Schwarz

At the El Realito project, Sonora, Mexico, the Luz del Oro joint venture has recently inferred a geologic resource of 400 to 800 kt of 2.5 glt gold potentially present in gossans, breccias, and veins. El Realito, under investigation for a dump leach, open pit operation, is located in the Sun Antonio Mining District where gold and silver veins and gold placers have been exploited since Spanish colonial times.

Jan 1, 1990

By A. I. A. Salama

A computationally efficient technique for generating a balanced set of density or size separation data is developed. The technique proposed utilized minimization of a modified form of error squares to generate the optimum estimates of outputs mass yields (splits) and balanced direct mass distributions of feed and outputs. The estimated separation data set satisfies mass balance conditions of the streams mass distributions around the separator. The technique proposed avoids the generation of small negative values for the estimated feed and outputs direct mass distributions. Actual data are used to demonstrate the technique proposed.

Jan 1, 1996

By R. Vergunst, E. A. Devuyst, G. Robbins

By the middle of 1989 Inco will have applied its patented cyanide removal technology to seventeen commercial operations. Removal of cyanide from CIL slurry tailings is applied at Equity Silver and Inco&apos;s new 1.200 mtpd mill at Inco/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3.600 mtpd), Canamax&apos;s Ketza River (360 mtpd) and Westmin&apos;s Silbak Premier (2000 tpd) operations. Repulped tailings from Merrill-Crowe flowsheets are treated at Total Erikson&apos;s Mount Skukum (300 mtpd) and Skyline&apos;s Johnny Mountain (200 mtpd) mills and barren bleed at Inco/Queenston&apos;s McBean mill (500 mtpd). Lynngold&apos;s MacLellan mill (1800 mtpd) and ERG (40.000 mtpd) treat pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating and two other plating shops in Ontario. Details regarding some of the above operations are given. Operating and capital cost estimates for various treatment options are discussed.

Jan 1, 1989

In analyzing cost performance, managers must initially consider the issue of scope. Is the analysis for a single responsibility center or multiple centers? For a single period or a number of periods? If multiple responsibility centers are being examined, how can managers compensate for differences in their sizes? Several techniques have been developed to analyze the relationships in a set of financial statements at a single point in time and the trends in these relationships over multiple periods. Cross-sectional techniques focus on the first of these, and time-series techniques look at the latter. Although this text focuses on cost performance, these methods also can be used for revenue-related analyses.

Jan 1, 1999

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By Cindi Byrns, Andy Davis, Amy Tisdale

The Robinson district, Ely, Nevada is a hydrogeologically complex system with several distinguishable geologic blocks, each with a distinct background groundwater chemistry. To discriminate between background and mine-impacted groundwater, background wells, monitoring wells, pit lakes, waste rock seeps, and surface water samples were analyzed for a suite of major cations and anions, together with trace and precious metals, rare earth elements, 2H-deuterium and 18O/16O. The data allowed identification of groundwater flow paths, verification of hydrochemical source areas and characterization of natural attenuation mechanisms (e.g., mixing, dilution and mineral precipitation) that control the concentration and migration of metals at the site.

Jan 1, 2000