Search Documents

By Robert J. Timko, R. Lincoln Derick

This report presents a Bureau of Mines evaluation which examined the extent of gas leakage from sealed areas in underground coal mines and measured the effectiveness of commonly used structures for controlling the quantity of gas exchange from these areas. Evaluations were performed on five abandoned areas in two operating underground mines within the same coal seam. Methane and oxygen levels inby the seals were monitored to determine if the gas leakage was unidirectional or bidirectional. Results from this and prior work dealing with minimizing gas leakage were then applied to a newly abandoned area. Also discussed are bulkhead site preparation, construction plans, techniques for monitoring the status of the atmosphere within the sealed volume, and a modified European method for controlling gas migration from the sealed volume to the active mine.

Jan 1, 1991

By J. Lorosch

Improvement of current leaching technology was found necessary when processing ores which are more difficult to leach because they generate highly viscous, air-rejective pulps. Cyanidation of these pulps has to run at low oxygen concentrations if the conventional aeration technique with compressed air is used. Since the dissolution rate of precious metals mainly depends on the concentration of dissolved oxygen in the pulp [1, 4, 5], the kinetics of the gold extraction become slow in such cases, which in turn often leads to a significant decrease in the overall gold output within the conventional leaching time of up to 48 hours.

Jan 1, 1988

By Jan Wolski, Jack Barry

Ventilation ductlines with a single fan or with a series of fans are analyzed. The duct friction loss factors are discussed. Numerical solutions, presented in the paper, applies to any fan number and locations along a duct line. The findings are compared with formulas available in the technical literature. Values of the air leakage factors are presented in the SI, technical metric, and US unit systems. A method is shown of how to determine the leak- age factor for a given ductline. Optimum solutions for the sample duct lines with two and five fans in series are discussed and presented in a graphical form. Performance of fans in series is discussed in conjunction with both friction pressure loss and leak- age.

Jan 1, 1997

By A. J. Monhemius, R. G. Reddy, G. W. Warren, E. Peters

Thermodynamic solubility of chromium in pickling solutions (i.e., HF- HN03-H2O solutions) was determined as a function of HF and HNO3 acid concentrations at 298K. Pure Cr, AISI type 316 and 416 stainless steel were used in this study. The results showed that the solubility of Cr increased with increase in the concentrations of HF and HNO3 acids in solutions. The solubility of Cr increased in the order of pure Cr > 416 SS > 316 SS. The theoretically calculated Cr solubility data were in reasonable agreement with the experimental data.

Jan 1, 1993

By Bruce Hern

The last 10 years have seen a dramatic increase in the requirements for product coal quality control. This has led to electric utility sulfur scrubbing, metallurgical blast furnace optimization and coal producer blend and yield optimization. To achieve this improved level of control, coal producers are designing facilities that emphasize new technology. New facilities will be designed and existing facilities will be retrofitted with state-of-the-art technology to meet quality control standards that are dictated by the market. The first step in designing for process control requires the identification of those parameters to be controlled and the upsets that can cause variances in the final shipped product quality. The most common parameters that require control are the surface moisture (%), ash (%), pyritic sulfur (%) and gross calorific value (Btu). Total moisture is that moisture that exists on the surface of the particle and is inherent in the particle itself. For the purposes of control, the total moisture is monitored, while surface moisture is controlled. Ash is the inorganic residue remaining after all other constituents are burned away at 75O°C( 1382°F)(ASTM, 1992). Sulfur is the amount of total sulfur that exists either as pyrite (FeS2), inorganic sulfate (FeS04), or organic sulfates (C4H4S) (Leonard, 1979). Currently, pyrite is controlled and total sulfur is monitored. The gross calorific value is the amount of heat produced when a unit quantity of coal is ignited under specified conditions. In this case, a l-g (0.03-oz.) sample of coal is ignited in an isoperibol waterbath and the temperature rise of the water bath is observed. The moisture and ash-free (MAF) Btu is relatively constant for a given seam, resulting in the whole calorific value being a function of the moisture and ash levels (Leonard, 1979).

Jan 1, 1994

By Anna Arkhireeva, John N. Hay

Considerable interest has been shown recently in organically modified silicates (ormosils) because of the wide range of possible applications for these interesting organic-inorganic hybrids. These applications include the use of the hybrids as modifiers of a range of host polymer proper- ties. The ormosils can be synthesised by the conventional hydrolytic sol-gel process, as well as by the non-hydrolytic sol-gel route. To date, however, there are relatively few reports of the synthesis of sub-micron size ormosil particles of well-defined spherical morphology. Here, we report work to date on synthesis of such nanoparticles and also introduce our own work in the area.

Jan 1, 2003

By Mahmud Esad Uluer, Aaron Noble

Respirable coal mine dust (RCMD) is one of the biggest occupational health hazards for underground coal miners. Coal extraction is a main source of RCMD. To prevent challenges related to RCMD from developing, it is vitally important to limit airborne RCMD and stay within the regulatory limitations for mine operators. The flooded-bed dust scrubber (FBS), mounted on a continuous miner, is one of the most widely used dust mitigation technologies in room-and-pillar mining, but it is limited by technical challenges, the most notably being the potential to clog. In this study, the impact of mesh design and surface modification on system efficiency is examined using different vibrating, liquid-coated, stainlesssteel mesh panels in a laboratory-scale FBS.

Sep 1, 2024

By Don Minard

Management support systems are extremely important to mining management to enable them to operate their company as a business. Management must give attention to the financial, maintenance, materials, and other reporting and control systems that are necessary to successfully operate a mining company. This subsection describes the management support systems that are critical to most mining companies. In this introductory review, the major objectives and functions of these management support systems will be introduced. The following topics will expand on the functions and key concepts as well as other considerations in each of these systems areas. Additionally, this introductory review will touch upon the unique environment that mining companies find themselves in from a management and personnel standpoint and the effect of this environment on management systems. Additionally, specific keys to successful systems installations and acceptance in the mining industry are discussed.

Jan 1, 1979

By K. I. Cunningham, C. S. Spirakis

Two types of native sulfur deposits have been found in Lechuguilla Cave: thin late-stage crusts and massive early- formed deposits. Most, if not all, of the crusts appear to have formed by remobilization of native sulfur contained within gypsum and sulfur masses. The process is occurring today and is slowly converting the sulfur to gypsum. The absence of primary gypsum or reductants in the cave indicates that the early-formed massive sulfur deposits did not form by in-place reduction of sulfate, which is the process that formed the commercial sulfur deposits in the Delaware basin. Instead, it appears that H2S dissolved in basinal brines was oxidized by oxygen in near-surface ground waters in the cave. Fluid- inclusion data, which suggest the presence of both fresh water and saline water as the sulfur formed, support this interpretation. Although individual sulfur deposits in Lechuguilla Cave are no more than several tens of metric tons, the abundance of secondary gypsum (as much as 10 meters thick) indicates that native sulfur may once have been much more extensive.

Jan 1, 1992

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In practice, however, coal blending is, at best, coal mixing. The degree of blending sophistication required depends on the reason for coal blending in the first place. If it is to maintain fuel characteristics that will diminish the chance of slagging and fouling, then some swings in variability may be tolerated at some power stations. However, if emissions limits are the issue, then more sophistication may be needed. Emissions limits are becoming stricter with requirements to meet averages for shorter time frames (hours and days instead of weeks and months). These restrictions require closer control over the quality of the blend being fed into the bunkers at the station. Even scrubbed units should have a consistent quality of fuel as feed so that sorbent additions can be minimized. To meet these challenges, engineers must consider available equipment and control techniques and the properties of the parent coals when evaluating new blending systems.

Jan 1, 1994

By George W. Poling

Designing optimal placer gold recovery plants requires a detailed knowledge of the size, shape and surface physical characteristics of the gold particles and the host alluvium in the pay gravel, sand or clay. Results of a recent pilot-scale study of the quantitative performance characteristics of riffled matted sluice systems are presented. For the appropriate non-coherent pay gravel-sand with medium-flat gold, simple sluices can recover gold at greater than 85% efficiency down to 100pm diameter. Alternatives to simple sluices are presented and discussed briefly.

Jan 1, 1987

By H. Y. Sohn, H. K. Lin

The leaching of primary porphyry chalcopyrite ore under simulated solution-mining conditions was studied using a packed-bed reactor. A mathematical model incorporating the intrinsic leaching kinetics of chalcopyrite and pyrite grains, the pore diffusion of dissolved oxygen within the ore fragments, liquid-solid mass transfer, and the effect of fluid flow and axial dispersion was formulated and tested for the overall leaching process. The dependence of oxygen solubility on ionic strength of the solution was also incorporated into the model. Satisfactory agreement between model pre- dictions and experimental data was obtained. The model can also predict the rate of the leaching process under different temperatures, oxygen pressures, solution flow rates, and different size distributions of ores.

Jan 1, 1991

By Fernando Concha, Arturo Barrientos, María Cristina Bustos

Manufacturers referred to high capacity thickening as a filtration operation rather than thickening in spite of the fact that it is performed in thickeners and that conventional thickeners can be operated as high capacity thickeners by changing the feeding level and operate it in a different manner. In this work we derive a phenomenological model for high capacity thickening based on mass and momentum balances. The difference with a conventional thickening is the presence of a surface source within the variable domain. The model can be used to design, simulate and to develop control strategies.

Jan 1, 1995

By M. L. Leming

Introduction In the decades since silica gel was first identified in material exuding from cracked concrete, a great deal of research has been conducted regarding the chemical reactions between the alkalies found in portland cement and silica found in aggregates. The reaction is complex and one that is not yet completely predictable, especially from the point of view of developing specifications that are appropriate to all situations. This paper is not intended to be a rigorous review of the research findings but is an attempt to provide a simplified review of the mechanisms of the alkali-silica reaction (ASR), so that one can better understand the implications of the specifications, test results and effects on structures. In addition, the contractual relationships between the aggregate supplier and one of their major clients, the concrete supplier, will be examined with regard to the ASR. ASR basics Silica. Silica (silicon oxide) may exist in naturally occurring aggregates in various forms and in combination with a number of other elements. When the silica is completely crystalline, such as in quartz, it is chemically and mechanically stable. Quartz silica is impermeable and reacts only on the surface of the crystal, where the silicon and oxygen bonds are broken. Because the surface area per unit volume of most quartz is low, the reactivity is also low. Completely amorphous (noncrystalline) silica is, on the other hand, more porous and very reactive. The less "crystalline" the silica is in the aggregate, the more reactive. Silica that has melted and cooled quickly without recrystallizing, creating a glassy material (such as in certain volcanic aggregates), has a very low state of crystallization and will be much more reactive in an alkaline solution. Crystalline silica that has been transformed by heat and pressure may have a large quantity of strain energy stored in the crystal lattice. The presence of this higher energy will make the silica more likely to react. The "strained quartz" found in many metamorphic aggregates means that these aggregates are potentially susceptible to deleterious alkali silica reactivity, although the rate of reaction is typically much slower than with aggregates composed of or containing glassy or amorphous silicas. Another problem may exist with aggregates in which the silica is primarily crystalline. In aggregates such as chert, in which the silica exists as very fine crystals (i.e., crypto- or microcrystalline), the very high surface energies between the crystals contribute to alkali sensitivity. Therefore, the potential reactivity of an aggregate is seen to be a function of both the degree of crystallization of the silica in the aggregate and the amount of energy stored in the crystal structure, whether due to a large quantity of microcrystalline silica, a high strain energy stored in the crystals or some combination of these factors. The surface area per unit volume of the reactive silica will also affect the rate of reaction, because a larger surface area of reactive silica will have more opportunity to react. Obviously, the reactivity of the aggregate is also affected by the silica content. However, in this case, the results are not quite so obvious. A discussion of the effect of silica content will be postponed until after a discussion of the contribution of the cement paste. Paste characteristics. Hydrated portland cement is a very alkaline material with a pore solution pH typically in excess of 12. The alkaline environment of moist concrete provides an ideal place for noncrystalline or cryptocrystalline silica to react. However, not all alkalies are equal in their effects. Calcium compounds react with glassy silica to form calcium silicate hydrate, commonly abbreviated C-S-H a poorly crystalline material that can occur in several forms and chemical compositions. C-S-H was at one time called tobermorite gel, because it was chemically similar to the naturally occurring crystalline mineral tobermorite and because it had a gel-like (noncrystalline) structure when viewed under an optical microscope. The formation of C-S-H is the basis for both portland cement hydration and reaction with, for example, fly ash. C-S-H is relatively stable. Although drying will cause some shrinkage and rewetting will cause some expansion, the volume stability of the C-S-H is very good compared to the volume stability of most alkali silica gels. Alkali silica gels with high sodium contents, for example, are nonstable compared to C-S-H.

Jan 1, 1997

By A. G. Mayton, L. Adler

The paper under discussion provides an excellent and concise study of compartment ergonomics for thin seam equipment. However, in accomplishing this, some very important operational aspects were ignored. Since these are likely to be determinant, the authors' response is solicited. The novel shuttle car with its cross-car, end-mounted compartment is operationally very different from the current one. The latter can be considered a highly mobile extension of the continuous miner or loader, with a pass-through conveyor, dump boom, and extra storage. As such, the vehicle's kinematics are the simple "I," or shuttle pattern, bent for going around pillars, with an intermediate stop at the "change-out point" (Adler, 1986 ). The action of the cable reel adjusts well to this pattern. The proposed shuttle car's motion either superimposes a "Y," time is lost (5 seconds) for each cycle, space is needed, line of sight is compromised, and a cable anchor is probably required at the dump. A chute is almost prohibitive in construction time and cost. The lack of a dump boom further curtails flexibility in the proposal. The value of a standard hand and opposite standard hand configuration also needs consideration. Many front-end loaders have a rocker (overshot) capability that is designed to achieve an "I” pattern. And crawler loaders sometimes use a side dumping bucket variant for the same purpose. These examples indicate the pattern's importance. For underground, thin seam application, the ram car has become popular. This is an articulated truck, battery-powered, and with an ejector dump. Its operational patterns would be similar to the novel shuttle car, except without the loading flexibility provided by a conveyor. Since the cab location of the proposed shuttle car largely obviates some of the major advantages of the present shuttle car, the question arises whether this configuration could be adapted to the current ram car and scoop

Jan 1, 1991

By K. N. (Mani) Subramanian

A 2.5 meter diameter column has been successfully used in a 100 tph flotation plant at the Harbour Lights Mine in Leonora, Western Australia, to produce a final gold bearing sulfide concentrate from the ore in a single stage. This pioneering application of column flotation cells to rougher stage was pilot tested using a 11 cm column, which demonstrated column's capability in rougher, scavenger and cleaner flotation stages. A hybrid circuit involving columns and mechanically agitated flotation cell s was adopted for the commercial installation. This paper describes pilot plant results, design of the plant flotation circuit, and early results of commercial operation.

Jan 1, 1988

By C. Garcia, H. Arias, J. D. Miller, C. L. Lin

The question of ultimate recovery in heap leaching operations is always of particular concern with respect to economic considerations. Of course the particle size distribution is a critical factor which determines ultimate recovery and which must be established based on a balance between the extent of mineral exposure and transport phenomena. Now it seems that the ultimate recovery for a given particle size distribution can be established from mineral exposure analysis by x-ray microtomography (XMT). Using recently developed software, micro-CT data can be used to determine the fraction of mineral exposed and thus the ultimate recovery. Examples of mineral exposure analysis are given for the copper heap leaching operation at Zaldivar, Chile.

Jan 1, 2002

By Lawrence A. Ph. D. Hansen, J. David Deatherage

Laboratory testing programs were conducted to investigate the performance under compression loading of several types of geomembranes and geotextiles proposed for use in heap and dump leach projects. Synthetic liners of several thicknesses were sandwiched between representative subgrade soils and cover materials, thus modeling in the laboratory the actual installation conditions expected. Performance was evaluated by visual inspection and vacuum testing. Several testing procedures and equipment were used to investigate the effect of these testing parameters on the predicted performance.

Jan 1, 1987

By M. Karmis, C. Haycocks

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

By M. Ghoreychi, M. Fauueau, P. Lebitou, P. Berest

A brief study of the history of gas caverns in salt formations enables us to consider creep mechanism in a cavity as a phenomenon of dissymmetrical deformation. Among different parameters affecting such a phenomenon, gravity forces, especially in large caverns, seem to be responsible for important bottom heaves as compared to roof releases. This fact is demonstrated here by means of certain theoretical considerations concerning elasto-viscoplastic constitutive laws relevant to rocksalt rheological behavior.

Jan 1, 1986