Search Documents

By J. B. Rubinstein, V. J. Badenicov, S. T. Hall

A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calcetest results is developed (scaling-up), and applied for calculating the design of commercial-scale columns.

Jan 1, 1996

By Normand Tassé

Reactive barriers, which consume oxygen, are prospective though unconventional alternatives to physical barriers for Acid Mine Drainage prevention. However, a reactive barrier implies a problem of duration. Pore gases were analysed in several wood waste piles in order to understand the factors which control wood degradation and help to determine the effective life span of such a cover. Long term efficiency seems to strongly depend on the degree of water saturation at the bottom of the pile, likely because the development of a microbial biomass in such an environment helps to keep the amounts of nutriments and readily metabolizable organic substrates at a high level, which in turn promotes oxygen consumption.

Jan 1, 2000

By E. P. Fahrenthold, K. E. Gray

Introduction Brine reservoirs along the Texas and Louisiana Gulf coasts are currently under study to investigate the technical and economic viability of production wells designed to extract methane gas in solution. The effect of well pressure drawdown on reservoir rock and associated overburden material is important to well performance predictions and the analysis of potential subsidence problems. Consequently a series of compaction tests have been conducted on sandstone and shale cored from a test well drilled near Hitchcock, Texas, in order to determine the variation of mechanical properties to be expected over the producing life of the formation. Previous Work The referenced tests are part of an extended study of geopressured-geothermal reservoir behavior, including compaction (Jogi, Gray, Ashman, and Thompson, 1981 and Jogi, Kalra, Gray, and Thompson, 1981) and creep (Thompson, Jogi, Gray, and Richardson, 1981) tests of reservoir rock and related reservoir performance studies (Rago, Okhuma, Seperhnoori, and Thompson, 1985). Recent work has considered the nonlinear constitutive behavior of sandstone (Fahrenthold and Gray, 1985 and 19861, while additional experimental work is reported here. Geological structure and composition of the Hitchcock field from which the core samples were obtained is discussed by Light (1985). Experimental Procedure Compaction tests were conducted on cylindrical cores, nominally 2.75 inches in length and 2 inches in diameter, with independent control of the axial, confining, and pore pressures. Axial and radial deformation of the samples were measured in tests over a range of effective stress states expected to develop over the reservoir lifetime. The term effective stress as used here refers to the algebraic difference of the total stress and pore pressure, with compression taken as positive. Three types of compaction tests were conducted on the sandstone. In the uniaxial tests, axial total stress and radial strain were held constant as the pore pressure was reduced, similating one dimensional compaction which may occur during reservoir depletion. In the triaxial tests, radial total stress and pore pressure were held constant as the axial total stress was increased, duplicating conventional rock compaction test procedures. In the pore pressure drawdown tests, axial and radial total stresses were held constant while the pore pressure was reduced, in order to investigate differences in sample response to mechanical and pore pressure loading. Compaction tests were also conducted on shale material obtained from the reservoir overburden. The field coring process provided few consolidated shale sections sufficiently large to allow preparation of samples with the dimensions described above. With additional attrition during sample preparation of this brittle material, ultimate yield of the coring effort was limited. The few available samples were tested in uniaxial and triaxial tests similar to those described above. The use of displacement transducers to measure sample deformation avoided the difficulty of strain gauge installation on this material. Test Results The sandstone and shale both demonstrated nonlinear stress-strain behavior, with hysteresis and residual strain present upon unloading. Polynomial interpolation of the stress-strain curves was used in the calculation of incremental values for the loading and unloading moduli. Figures 1 and 2 show example axial effective stress-axial strain curves for triaxial tests conducted on sandstone and shale samples. The figures plot incremental stress and strain variables, defined as deviations from the state of prestress to which the sample was subjected. The state of prestress was varied between tests in order to investigate material behavior over the entire stress and strain space of interest. Tables 1 and 2 give the incremental moduli (Young's modulus and Poisson's ratio) as a

Jan 1, 1986

By R. Hogg, M. Polat, S. Chander

A fresh dust generator was designed and built in order to study the agglomeration behavior and other characteristics of freshly generated airborne dust. The size distribution of the freshly generated quartz airborne dust produced by the generator was measured both directly in air and after dispersion in water. It was observed that same dust particles had an apparently coarser size distribution in air than in water, suggesting possible agglomeration of the dust particles. It was also observed that the size distribution obtained by a cascade impactor was very similar to the liquid dispersed size distribution, implying deagglomeration by the impactor. The agglomeration was confirmed by microscopic observations of particles in air and those collected on a microscope slide. The extent of agglomeration played a decisive role on the fraction of the dust actually becoming airborne. It was also found that contamination of the airborne dust by the rolls of the crusher was almost twice as much as that of the product.

Jan 1, 1991

By Bruce T. Stanley

Though most porphyry-molybdenum deposits lend themselves to various reserve estimating techniques, still there must exist the constant effort to not merely obtain an estimate but rather to obtain the best estimate. To answer the challenge of a complete ore reserve estimation, one must attack the problem with the purpose of obtaining the results closest to reality. What we wish to determine is simple: metric tons (short tons), grade, and kilograms (pounds) of molybdenum contained. In order to effectively accomplish this task, further consideration must be given to the ease of using the information obtained and its inherent reliability. The only known method for ore reserve estimation that supplies the needed results along with its distribution and a measure of confidence provided by sound mathematical backup is geostatistics. The following review is an example of geostatistical application of an ore reserve estimate at the AMAX Henderson mine demonstrating technique, viability, and usefulness of results.

Jan 1, 1979

By Gregory Witte

This paper will explore the technology behind and applications of smart motor control centers (MCCs) being used today in mineral processing facilities. The two technologies to be discussed are solid-state motor controllers that can be installed in MCCs and the complementary digital communication networks that can transmit operational parameters of the solid-state devices to the supervisory system. The toughness and reliability of solid-state technologies have led to a dramatic increase in their usage throughout the mining industry. Products such as solid-state motor protectors, controllers, and variable frequency drives have demonstrated greater flexibility and performance in a variety of applications than their electromechanical and mechanical counterparts. The three key trends apparent in the solid-state devices are: 1. A shift to smaller, smarter, more integrated devices, which allows a single solid-state device to serve the purpose of multiple electromechanical devices but in a much smaller form factor. 2. Distribution of control logic in motor control devices rather than conveyed through a hard wired connection to a central automation system. 3. Embedded network communication that allows supervisory systems to have an expanded view into critical loads and sensors. In applications, the use of smart actuators and sensors with integral local intelligence and communication allow a supervisory controller to send high level commands and let the smart device coordinate its own work The ability of smart field devices to return noncontrolled, nonpoled information opens a whole array of new capabilities for preventive maintenance and diagnostics and forms the basis for an effective motor management program. The smart motor control devices this paper will explore are the smart motor protectors (SMP), smart motor controllers (SMC), and variable frequency drives (VFD).

Jan 1, 2000

By J. Chappell

The Nuggety Gully prospect is located 170 km (106 miles) south- east of Port Hedland and 40 km (25 miles) northeast of Marble Bar in the Pilbara Region, Western Australia. The area is held under title by Esso Exploration and Production Australia, Inc. The prospect covers a significant, but currently uneconomic body of molybdenum and copper mineralization of porphyry style, associated with Archean high level acid intrusives intruding sediments and volcanics of a narrow east-west Archean greenstone belt. The Nuggety Gully intrusive rocks have been dated at 3.2 b.y. ± 117 (de Later, oral communication). The current resource estimate for the deposit is 102 Mt (1 12 million st) of 0.1 1 % Mo and 0.15% Cu.

Jan 1, 1991

By Kadri Dagdelen, M. Waqar Asad

Cement production involves the processing of raw materials that contain - Si02, A1203, Fe203, CaO, MgO, LOI (loss of ignition), S03, K20, Na2O, Ti02, P2055 and Cl- to produce the synthetic mineral mixture called "clinker". The use of other additives - sandstone, flyash, iron ore, and clay - is also mandatory in order to achieve the optimum blending requirements of cement. However, the use of these additives needs to be minimized due to their significantly higher costs ($/Ton). This paper presents a mixed integer programming (MIP)-based optimum quarry scheduling algorithm, which is used to generate quarry plans, satisfying geometric and production capacity constraints while providing minimum cost/optimum blend of raw materials mix to a cement plant. The benefits of this new methodology are demonstrated on a case study.

Jan 1, 2002

By D. Leppert

Mr. Garrett brings up several interesting points with respect to the proposed API specification for "nontreated bentonite." However, although not explicitly stated, these specifications are being written based strictly on bentonites from the Wyoming/South Dakota area. Other sodium bentonites may be suitable for use as drill mud but will be unacceptable since the specifications are designed for Wyoming bentonites. Regardless of the API's intent that its specifications are intended only as guidelines, they are generally adhered to on an international basis and, for practical purposes, might as well be chiseled in stone. Estes (1986) notes that the quality of bentonite available from Wyoming producers has steadily declined since the early 1960's. The plastic viscosity: yield point (PV:YP) ratio was included in the current API 13A specification primarily to prevent excessive polymer treatment of lower quality bentonite to make drill mud. However, with development of polymers designed to control YP, this specification cannot ensure that only high-quality bentonites are used for drill mud. Nor will the new specifications for untreated bentonites. Other sodium bentonites are available. Bentonite produced in southeast Oregon demonstrates superior performance characteristics without addition of polymer or other chemicals. However, the exceptionally high purity of these deposits leads to a relatively high YP:PV ratio since the naturally high YP probably results from the higher purity and smaller particle size of this bentonite (Rath. 1986 and personal communication). These bentonite; typically have a smectite component exceeding 90% (Rath, 1985), compared with 70% to 75% smectite for typical Wyoming bentonites, as determined by X- ray diffraction and tests for colloid content. As evident from the accompanying table, the untreated Oregon bentonite has excellent rheological properties, though different from Wyoming bentonites due to the high purity. Additionally, this bentonite reacts well with polymers typically used in the oil industry, making it eminently suitable for use in a low-solids mud system. The extremely low grit content, less that 0.5% on a 75 mm (200-mesh) wet sieve, greatly exceeds the standards set for Wyoming bentonite. Optimum rheological properties are obtained at a higher moisture content than Wyoming bentonites. At 10% moisture, API 13A maximum, the clay is overdried, again reflecting the high smectite content. In summary, the specifications proposed by the API Task Group will ensure that only Wyoming producers can supply "nontreated bentonite to the oilfield since specifications are

Jan 1, 1990

By Val Ness, Leonard Harris

Mentoring is defined as close counseling by an experienced and objective advisor within the industry. It is one aspect of attracting the best candidates into the minerals industry, holding their interest, and encouraging stable career growth. By encouraging proper mentoring practices, we foster strong careers, we transmit important wisdom to the next generation, we fortify the industry with better talent, and we encourage the best possible advocates for the minerals industry. This paper illustrates the consequences of poor mentoring, offers an example of positive mentoring practice at the college or university level, reviews some guidelines for stable and fruitful mentoring, and proposes a plan to spread appropriate mentoring practices. Authors' note: The use of masculine pronouns is for convenience and simplicity only. Our best engineers and managers come from both genders, and the authors intend no slight to either one.

Jan 1, 2001

By T. Knuutinen, M. Klemetti, P. Mörsky

This paper presents a comparison study done at VTT's new pilot plant facilities in Outokumpu, Finland, for chromite ore. The ore was ground in a rod mill -, a ball mill - and high pressure roller mill - ball mill circuit in the capacity range of 0.5 - 3.0 t / h. The main grinding characteristics are discussed and the quality of the products are compared from the mineralogical point of view. The benefits of high pressure roller mill comminution for further mineral processing of chromite is also discussed.

Jan 1, 1995

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

By Jeffery H. Stricklin

Jim Walter Resources operates five underground coal mines with longwall faces in operation in four of the mines. Due to high air velocities (1000-1200 fpm) needed for methane control together with the friability of the coal, dust control on JWR longwalls offers unique challenges. We have tested many innovative measures to reduce respirable dust concentrations on longwalls with varying degrees of success. These measures include the "shearer clearer" system, different drum water spray configurations, sprays on the longwall belt, stageloader and crusher sprays, wetting agents in the spray water system, and homotropal ventilation. Water infusion of deactivated horizontal methane drainage holes in longwall panels is now being evaluated. A study was completed in November 1986 where water was infused into two horizontal de-gas holes. Personal gravimetric samplers were used to measure respirable dust concentrations and showed a significant reduction in the infused zone. A more in depth study will be conducted. This paper will describe the dust control measures presently used on JWR longwalls, give the results of past studies, and discuss new methods proposed to control longwall dust.

Jan 1, 1987

By Zhongxue Li, Wenguang Li, Yiqing Zhao, Shuaiqi Wang

"Faced with the serious managerial situations and diverse conditions and needs for mine safety, occupational health and environmental stewardship in Chinese mining communities, an evidence-based approach is proposed for the management of mine safety, health and environment integrity. By the proposed approach, tangible and effective scientific evidence should be collected and accumulated, and the authenticity, accuracy and applicability of the evidence should be assessed to form an evidence-based approach for characterizing mine safety, health and environmental hazards and risks from multidimensional perspectives. The results are then used to formulate diverse safety, health and environment functional requirements. In an evidence-based approach, the evidence is combined with the professional experiences and the actual economic and technological situations, availability and affordability of a mine. This approach is helpful to establish scientific, reasonable, acceptable and effective solutions for identifying and mitigating hazards and improving the level of mine safety, health and environment integrity of mining operations.Introduction / Background In recent years, economic reforms have opened China's economy so that Chinese society has rapidly modernized. Along with this advancement, the exploitation and utilization of mineral resources continues to be active and the scale of mining production continues to increase, which has created a deterioration in resource reserves and as well as the general condition of mining technology. There are many hazards and safety problems in mine production and occupational health as well as in the community environment in China’s mining industry. These problems threaten the security of China's mines and present serious obstacles and challenges to the industry and the government. According to the statistics from the State Administration of Work Safety Supervision, there were 50,500 mine safety incidents in China between 2001 and 2013, which consisted of 31,439 coal mine safety accidents and 19,061 non-coal mine safety accidents, resulting in 30 deaths (Qin 2014). At the same time, mineral dust and radioactive material from mine production processes have increased the morbidity rate of silicosis and cancer in mining workers."

Jan 1, 2017

By Peter K. Weissenborn, Robert J. Pugh

The contrasting behaviour of electrolytes in inhibiting coalescence of bubbles was explained by the positive and negative distribution of anions and cations at the gadwater interface. Further, the efficiency of electrolytes which do inhibit coalescence of gas bubbles can be linked to a counter ion hydration mechanism and the effect of electrolyte concentration on gas solubility. A correlation was found between the transition concentration of electrolyte needed to prevent the coalescence of bubbles and the reduction in gas solubility. Hence, the inhibition of bubble coalescence in electrolyte solutions appears to be linked with the utilization of water molecules in the hydration of cations and a consequent reduction of water available for gas solubility.

Jan 1, 1995

By C. O. Hamilton

Poor plant start-up performance is usually blamed on poor design and unsatisfactory equipment. But, in most cases, the real cause of poor performance is inadequate preparation for operations and maintenance. Inadequate maintenance preparation, unlike inadequate operations preparation, will not immediately manifest itself in a new plant. However, not taking advantage of the window of opportunity afforded a new plant to organize the maintenance operation ensures that the new equipment honeymoon is unexpectedly short. Also, once a plant has entered a “breakdown mode,” it is extremely difficult to turn around.

Jan 1, 1991

By K. Hebbar, R. G. Reddy

The viscosities of various FeO-SiO2 slags were calculated using a previously developed structural-based model. Using hole theory and the atomic pair model, an expression was derived to relate the viscosity to temperature and the fraction of the bridging oxygen in silicate melts. The deduced equation was successfully applied to predict the viscosities of FeO-SiO2 slags in the composition range of 0.1 < XSi02 < 0.423 for several temperatures. The calculated data agree well with the experimental viscosity data.

Jan 1, 2002

By S. C. Suboleski, J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later it will semiautomate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide the section foreman with real-time or near-real-time information about the performance of the loading and hauling units. This data will allow the section foreman to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and in-mine testing results from the first phase are now available.

Jan 1, 1994

By J. N. Carras, N. W. Bainbridge

In order to further the understanding of spontaneous heating of longwall goafs a numerical model was developed, based on conservation principles applied to the transport of heat, water vapour and oxygen across the god Advective air flow into the goaf is caused by the differential air pressures across the god The air velocity field within the goaf area was computed using Darcy&apos;s law. The boundary and initial conditions concern air pressure, temperature and relative humidity. The oxidation rates and heat generation rates of the goaf materials required for the simulation were obtained from laboratory measurements. The main outputs of the model are temperature, oxygen and water contour maps, the rate of air leakage into the go4 velocity field and pressure distribution across the god. The model while still in its development stage, is able to simulate a heterogenous goafs constructed from different materials with different thermal and mass flow properties. Validation of the model by comparing its output with measurements from within goafs is required before the model can be used with confidence in a predictive sense.

Jan 1, 1995

By G. Banini

A plug-flow model is described for the reactor mass balance of a typical AARL gold elution process. The model is in the form of a hyperbolic differential equation and was transformed using the method of characteristics. The transformed model was then solved simultaneously with models dependent on intraparticle surface diffusion and film transfer parameters. The solution was found to represent the experimental data for a modified form of the AARL elution. Correlation between the experimental conditions and the film transfer parameters estimated by the model are also presented.

Jan 1, 1998