Search Documents

By N. S. Harding, M. C. Mai, A. G. Fonseca

Many coal characteristics affect combustion performance. Mill wear, boiler efficiency and derate, slagging, fouling, and ash collection and removal are only a few of the impacts of coal quality on boiler performance. The ability to assess fuel characteristic impacts on busbar costs is essential, although difficult to obtain. The relationships between coal characteristics and ignitability, operability, slagging, and fouling were investigated. The examination of combustion data/performance from a laboratory study, a boiler simulation system (pilot combustor), and commercial boilers indicated the benefits of burning improved quality coal. The specific effects of cleaning are discussed. A validation of the necessity of commercial-scale and/or pilot-scale testing is presented.

Jan 1, 1988

By Jr. Foot

EIMCO Process Equipment Company has introduced the new SmartCell series of conventional flotation cells. The flagship of this new development is the 5000 ft3 cell that is the largest available in industry. This new series of cells includes a cylindrical tank design, a conical draft tube and froth crowder. Optional air control, wash water addition and embedded expert control are available. A discussion of the design parameters, energy efficiency, testing, and commercial plant results are presented.

Jan 1, 1997

By Dominigue Francois-Bongarcon

This paper presents a step by step vulgarized review of the applications of geostatistics to the estimation of the mineable, recoverable reserves of the Cinola gold deposit in British Columbia.

Jan 1, 1988

By George A. Desborough, David L. Fey, Stanley E. Church

About 100 mine-waste dumps from past metal exploration and mining in Colorado and Montana were sampled using surficial-sampling methods for laboratory studies of the minus-2-mm fraction. In the laboratory, the composite samples were split into l00g samples that were leached to assess their acid-generation potential and associated release of potentially toxic metals that may degrade water quality in the headwaters of the Animas River watershed in Colorado and the Boulder River watershed in Montana. Two leach methods were studied: a passive leach using de-ionized water, and a more aggressive leach following the EPA-1312 method. The resulting pH values of the leachates using both methods are comparable. The concentrations of sulfate and several, but not all, dissolved or water-soluble metals are higher in the EPA-1312 leachates than in the passive leachates; however, the overall trends of the data are very similar. The passive leach method is less labor intensive and may be more representative of the natural weathering process occurring on the mine-waste dumps, simulating the natural precipitation and snowmelt. Three chemical characteristics of mine wastes studied here provide a relative ranking of mine-waste dumps for the purpose of determining priority for removal or remediation. These characteristics are: net acid production (NAP), sum of dissolved toxic metals (?As+Cd+Cu+Pb+Zn), and dissolved iron in leachates. Ranking can be done evaluating plots of NAP versus the sum of dissolved toxic metals, and NAP versus dissolved iron. These two plots serve as a basis for relative ranking of polymetallic-vein and acid-sulfate mine wastes studied. This ranking scheme may apply to mine wastes from production of other deposit types in other watersheds.

Jan 1, 2000

By P. E. Nielsen, T. L. Loga, B. B. Mauko

A numerical model is presented which simulates the dynamic fracturing process for a circular geometry fracture in a uniform stress medium. The dependence of crack aperture and net pressure in the crack upon various dominant parameters of the fracturing process is discussed. An analysis of a 75% nitrogen foam fracture in a coal seam at 5600 feet (1707 m) is also presented. The analysis is based upon the discussed parametric trends, the job records of treatment parameters, and a Nolte plot of net downhole pressure. It is interpreted that fracturing with water, in pre-foam fracture pump tests, resulted in significant fracture height growth. However, the subsequent foam fracture had reduced height growth due to the high effective viscosity of the foam and due to the higher magnitudes of elastic modulus and stress in the bounding rock strata with respect to the coal.

Jan 1, 1986

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986

By R. Hogg

The various sub-processes which, together, make up the unit operation of froth flotation all depend on the characteristics of the feed solids, the solution phase, the air bubbles and the mechanical/hydrodynamic action of the machine. Characterization is obviously necessary for evaluation and process control, but the relationships between characteristics and process response are often unclear. A model-based characterization scheme is proposed in which material and system characteristics are evaluated in the context of simplified models for the individual subprocesses. The general basis for such an approach is discussed using the process of particle attachment and the influence of mineral liberation as examples.

Jan 1, 1989

By R. W. Lawrence, P. B. Marchant

Biohydrometallurgy is now forty years old. Since the discovery of the role of microorganisms in the oxidation of sulphide minerals that gives rise to acid mine drainage, many workers in industry, research organizations and academia in many countries have been active in attempts to develop practical commercial processes which exploit microbiological reactions in mineral processing and extractive metallurgy. Reactions which have potential and are being actively researched include:

Jan 1, 1998

By K. G. Sutterer, P. T. Wang, R. Sweigard

One possible alternative for the disposal of flue gas desulfurization (FGD) by-products is to use it as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation in stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48% and the peak stress could be decreased by about 58%. The study indicates that fairly weak FGD materials can eventually lead to the stability of backfilled highwall adits.

Jan 1, 1998

By Warren E. Fife

This paper will discuss the application of a continuous miner using a fixed drum milling type cutting head for the underground mining of hard rock and salt ores. Continuous mining machines of the ripper chain cutting head, oscillating milling cutting head and boring arm designs have been used in rock and salt applications with various degrees of success. The large boring arm miners have been successful in potash, trona and salt, but they have not been successful in mining rock materials like iron ore. The main method used in underground mining rock materials is the conventional drilling and blasting the ore from the solid. This is particularly true for the harder, more abrasive copper and iron bearing ores. The softer salt based ores of potash, trona and rock salt can use several underground mining methods depending on seam conditions. Several of these methods use underground coal mining equipment that has been extensively redesigned to adapt it for use in mining noncoal materials. Conventional mining methods employ the use of a universal cutting machine to undercut or topcut the ore body before face drilling and blasting takes place to produce a smooth parting of the ore. The boring arm continuous miner is widely used in underground mining of potash and trona ores. It produces a tunnel with a smooth semicircular contour which results in good rib and roof stability. The ripper chain continuous miner is also widely used in mining the salt based ores of potash, trona and rock salt. They are used more frequently in Europe than in the United States and Canada. Some reasons for using the mechanical mining machines as opposed to the conventional drilling and blasting techniques for mining hard rock ore bodies are the resulting improved rib and roof control, facilitates selective mining of the ore body, and requires less man-

Jan 1, 1974

By G. Granger, D. Malhotra

The paper briefly reviews the criteria employed in the selection of chemical reagents for testing and discusses the steps involved in laboratory and plant evaluation of these reagents. An example of successful implementation of reagent change in the plant is illustrated.

Jan 1, 1986

By Cory Bolen, Nadav Bar-Yaakov, Eric Zimmerman, Gregory Raines

The Chimney Hollow Reservoir Project broke ground in August 2021, constructing the tallest Asphalt Core Dam in North America, intending to improve reliability of drinking water supply to Northern Colorado communities. Aiming to expedite and streamline the geological mapping process in the tunnel, Stantec’s teams have developed a mobile and web-based GIS application for digital mapping input and rock mass evaluation, allowing real time decision making for assigning tunnel support class and resulting in a faster more efficient process. The following article presents and demonstrates the GIS mobile and web application-based process, the mapping results and review additional uses of the database created.

Jun 13, 2023

By W. E. Cobb

The financial implications of environmental liabilities are becoming staggering, particularly for mining companies. The Environmental Protection Agency's (EPA) Record of Decision (ROD) list for Superfund mining sites has some pretty hefty financial commitments, such as the $10 million operable unit remedy for the Yak Tunnel at California Gulch (in Colorado) or the $40 to 60 million remediation at Bunker Hill (in Idaho). These costs are driven by the large volume and areal extent associated with historical waste management practices at mining sites. (It's difficult to have a low-cost remedy for a 20-square-mile site.) Unfortunately, there are other ways of generating environmental liabilities besides Superfund, such as non-compliance with Clean Air Act provisions, stormwater permits, or National Pollutant Discharge Elimination System (NPDES) permits. In the last 2 years, EPA has increased enforcement in its regulatory programs, which has resulted in increased fines and criminal actions. Leaders in other industries (primarily the chemical and manufacturing industries) are viewing environmental liabilities as a strong motivator to select engineering approaches carefully based on technical, legal, economic, and philosophical perspectives. Industry interest in waste minimization programs comes from the concept that it is economically advantageous not to create waste in the first place. Waste minimization programs typically balance increased front-end capital investment with the minimization of potential long-term environmental liabilities as a way to achieve the lowest total-or life-cycle-cost. A side benefit of waste minimization programs is that they tend to improve overall regulatory compliance. Waste management practices are also becoming philosophical, as evidenced by a May 11, 1992, Business Week article: Companies that incorporate innovative thinking on sustainable development will do more than clean up or prevent their own pollution. They'll make and distribute a product more efficiently than ever, worry about its lifelong environmental impact, plan for recycling, and get their suppliers on the bandwagon. This type of approach will require a new mind-set, new tools, and adjustments throughout the organization. A key aspect of waste minimization or life-cycle waste management programs is the incorporation of environmental costs into economic analyses that compare various waste management alternatives. However, the incorporation of environmental costs into an economic analysis can be more difficult than initially thought. As noted above, new tools-or even a new toolbag-are needed, such as new accounting methods that track and assign the true lifetime environmental costs of a particular product. One piece of the new toolbag is life-cycle cost analysis, which is discussed in this paper. To simplify the discussion, this paper looks at the total costs associated with a given mining site. The concepts presented in this paper, however, can be applied to any mine waste management decision. The ultimate extension of life-cycle costing, as presented in the Business Week article, is to include the potential environmental costs throughout the life of a metal. At this point, I am perplexed on why, let alone how, to include the potential downstream environmental costs (i.e., the costs associated with smelting, manufacturing, use, and recycle or disposal) throughout the life cycle of mined copper, lead, or zinc.

Jan 1, 1992

By A. B. Szwilski

The mineability and coal processing costs are influenced largely by the structural and physical properties of the coal seam. The mining process involves coal cutting, pillar support, crushing, and floating. A correlation between the rank, ash content, and coal strength/stiffness is discussed. The coefficient of variability of rebound tests on the face of various coal seams are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1988

By V. McLemore

New Mexico ranks 2nd in uranium reserves in the U. S., which amounts to 15 million tons ore at 0.277% U3O8 (84 million lbs U3O8) at $30/lb (EIA, 2006). The most important deposit in the state is sandstone within the Morrison Formation (Jurassic) in the Grants district. More than 340 million pounds of U3O8 have been produced from these deposits from 1948-2002, accounting for 97% of the total production in New Mexico and more than 30% of the total production in the United States. Sandstone uranium deposits are defined as epigenetic concentrations of uranium in fluvial, lacustrine, and deltaic sandstones. Three types of sandstone uranium deposits are recognized: tabular (primary, trend, blanket, black-band), roll-front (redistributed, post-fault, secondary), and fault-related (redistributed, stack, post-fault). Several companies are planning to mine these deposits by in-situ leaching.

Jan 1, 2007

By D. F. Watson, G. M. Philip

The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write: "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accumulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common.

Jan 1, 1988

By D. E. Ranta, Leigh A. Readdy

Defining classes of ore using geostatistical methods that match historical classifications has presented problems in the past. A simplistic and practical approach to this problem is presented. An example of the approach is presented using a porphyry-type system as a case study. The technique described uses area of drill-hole influence and known conditions from similar deposits, or the production history of the deposit being studied. It provides a practical bridging mechanism for defining the class of ore on a block-by-block basis using the error of estimation value developed during kriging. The approach provides a filtering method that refocuses attention on the adequacy of drill-hole spacing.

Jan 1, 1992

By J. H. Bassarear, J. D. Vincent

General. Copper, the first metal used by man, today is the third in consumption after iron and aluminum. Compared to these it is relatively rare, with less than 0.01% of the earth's crust copper, 8% aluminum, and 5% iron. Nevertheless. our modern civilization is heavily dependent upon copper because of its high conductivity and resistance to corrosion, ease of working, durability, wide range of properties by virtue of its readiness to form alloys with other metals, and its attractive colors and texture that make it so desirable for many crafts and arts. These attributes explain why copper is chosen for a long list of uses, including electrical wiring, switchgear, and bus bars; piping, roofing, and siding; and manufactures of brass, bronze, and other alloys. The fact that copper ore is mined in nearly all parts of the world is significant. Its importance is shown in Table I, which gives figures on world production from 1968 to 1977. In the Free World, North and South America and Africa are preeminent. The table also shows the generally upward trend of production in this period; accurate figures for 1978 and 1979 from the same source are not yet available (1980), but it is certain that major environmental, economical, and political factors continued to disturb the industry in those years and into 1980.

Jan 1, 1985

By Garland R. Dever

Extensive deposits of high-calcium limestone occur in the Upper Mississippian Warsaw and Ste. Genevieve Limestones in the region of the lower Cumberland, Tennessee, and Ohio Rivers in western Kentucky. Analyses of foot-by-foot samples from 20 quarries and cores in 8 counties show variations between the chemical composition of high-calcium deposits in the 2 formations. Knowledge of probable variations in composition should aid in prospecting for high-calcium stone for a specific use and in evaluating potential deposits. High-calcium strata in the Warsaw consist of bryozoan- and crinoid-rich bioclastic limestones, and in the Ste. Genevieve, predominantly oolitic limestones. Values used for comparison were obtained by averaging the foot-by-foot analyses of each high-calcium deposit, 10 in the Warsaw and 15 in the Ste. Genevieve. Average MgCO3 and Fe2O3 contents are generally lower in the Warsaw than in the Ste. Genevieve. Average SO2, S, and P contents are- generally higher in the Warsaw. No characteristic differences are apparent between the average CaCO3 and A1203 contents of the two formations. The higher S and P contents of the Warsaw are believed attributable to the predominance of biogenic material in these limestones. Within the Warsaw Limestone, higher average S and A1203 contents and lower average Fe2O3 contents were found in deposits in the northern half of the region. In the Ste. Genevieve, vertical variations in composition occur within individual high-calcium deposits containing oolitic and nonoolitic limestones. Lower average CaCO3 contents and higher average contents for the other constituents were found in the nonoolitic intervals.

Jan 1, 1972

By Yong-ping Wu

Based on the rules of strata behavior and the characteristics of rock movement, the elementary problems of using fully mechanized coal mining techniques in steeply dipping coal seams are described. A model of the "surrounding-support-rock" relationship is made. The support systems stability during fully mechanized mining of steeply dipping coal seams is studied. Then, a practical engineering example of the fully mechanized mining of a steeply dipping seam is presented. The seam used in the example is in the Lushuidong colliery, which is administrated by Huaying Mining Bureau, Sichuan Province.

Jan 1, 2003