Search Documents

By Allen V. Reicks

Modern conveyor pulleys are welded steel structures subjected to dynamic loads. In this paper, fatigue notch and fracture mechanics methods are applied to several weld joints on typical pulley constructions. These methods are used to analyze field applications and are correlated with laboratory testing. Generalized approaches are presented which provide high confidence in pulley design with corresponding high reliability.

Jan 1, 1996

By M. Kumral

The in-situ mineral characteristics of a deposit are simulated by sequential co-simulation and averaging the simulated characteristics within specified block volumes creates a three-dimensional block model. This model is then submitted to optimal open pit and production scheduling algorithms. As the market values of industrial minerals depend on the satisfaction of predetermined blending criteria rather than metal content, a Linear Programming (LP) scheme has been used to identify all blocks that can be included in the blend without violating the grade requirements. The Lerchs-Grosmann algorithm using the blocks identified by the LP program determines optimal pit limits. All blocks that lie outside the optimal pit are removed from the system and the blocks within the optimal pit are submitted to the production-scheduling algorithm. Production scheduling optimisation is done in two stages: Lagrangean parameterisation, resulting in an initial sub-optimal solution, and multi-objective simulated annealing (MOSA) improving the sub-optimal schedule further.

Jan 1, 2002

By Hugh W. Rimmer

The design of comminution circuits and the evaluation of alternatives should be based on state-of-the-art equipment and appropriate design criteria - considerations that are often neglected by today's designers. This paper critically reviews common circuit designs, evaluates various alternatives for difficult-to-treat ores, and discusses the factors that should be considered when developing new plant designs or auditing existing plant performance. Data obtained from laboratory, pilot and plant-scale test work on a wide range of ores and circuits are used to justify the author's conclusions.

Jan 1, 1995

By K. N. Han, M. C. Fuerstenau

Challenges in five major areas of hydrometallurgy are presented and discussed. These are: leaching low-grade oxide and sulfide ores; oxidative leaching of sulfide concentrates; processing refractory ores; bacterial leaching and processing: and secondary metal recovery.

Jan 1, 1989

By Mark P. Schmidt, Douglas D. Schlepp

Water Only cyclones were introduced into commercial operation for cleaning of metallurgical and steam coal around 1950. Since its original introduction as a primary cleaning device, the employment of Water Only cyclones as recleaning and scalping devices has also grown in popularity. Examined are examples and uses of the water only cyclone as primary, re- cleaning, and scalping devices for fine coal cleaning. Also evaluated are conditions that should exist to ensure favorable cleaning in Water Only cyclones.

Jan 1, 1988

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By A. K. Mukhopadhyay, B. Sikdar, V. P. Arora

Introduction During the past several years, persistent concerns about an economic slowdown in India have tempered capital-expan¬sion plans. This has encouraged companies to find methods of increasing the capacity of existing production equipment. One of the more cost-effective methods of increasing produc¬tion capacity without major capital investment is to improve equipment maintenance to prevent needless machine down¬time. This can have a significant financial impact because of reduced maintenance costs and increased machine availabil¬ity. The maintenance program employs different techniques, but the analysis of the vibration behavior of machine compo¬nents to assess their condition was found to be the most accurate technique for monitoring various machine disorders. A dragline that handles overburden in open pit mines is one of the more capital-intensive pieces of production equip¬ment. It is imperative that the machine be run at its optimum capacity under the prevailing environmental conditions. Condition monitoring of the various components of the dragline through vibration analysis not only improves the machines availability but also ensures a long operation time free from sudden failure. This paper describes the application of vibration monitor¬ing and analysis techniques to assess the components of a W2000 dragline. The paper reveals that condition monitoring through vibration analysis can be as valuable in failure prevention as it is in failure analysis. Finally, the paper presents an approach to a knowledge-based expert system to the quick and correct diagnosis of mechanical faults in a dragline. Equipment A dragline is an intermittent-discharge-type excavator having a long boom at one end. Unlike other excavators, the bucket is not rigidly held by the frame structure. In favorable geomining conditions, the intensive operation of these exca¬vators is the least-expensive means of overburden removal. The basic working elements of this equipment are the hoist system, the crowd and retract system, the wing mechanism and the propel mechanism. The walking dragline is accepted as the most economical machine for stripping overburden at depths of up to 60 m (200 ft). They are electrically powered and the various motions are effected by individual drives. The Ward-Leonard system is used to provide the optimum flexibility in controlling different dc-drive motors. To mini¬mize the cost of mineral extraction, the largest such machine in India has a 24-m3 (850-cu ft) bucket with a boom length of 96 m (315 ft). Draglines are very costly, and considerable financial penal¬ties may arise from sudden stoppages due to component fail¬ures. Thus, operational reliability is of the greatest importance. Active measures are now being taken to minimize downtime by adopting condition-based maintenance techniques. Though a number of techniques come under this scheme, it has been observed that assessing the health of the dragline by measuring vibration is the best method of determining the dynamic behavior of its various rotating components to avoid any catastrophic failure. Based on criticality, the vibration-behav¬ior of the following components are studied: • motor-generator unit, • exciter unit, • hoist motor-gearbox unit, • hoist drum-gearbox unit, • drag motor-gearbox unit, • drag drum-gearbox unit and • swing motor unit The approach Increases in the vibration levels in different subsystems of the dragline were observed due to the presence of faults such as unbalance, misalignment, looseness and bad bearings. A vibration behavior study included the measurement of vibra¬tion level, trend analysis of time-domain vibration signals and vibration frequency analysis at bearing points of the components. A vibration meter, a vibration analyzer and a data collector are used. Vibration-level measurement. When the dragline was assembled and put into operation for the first time, vibration data were collected to generate baseline data for the equip¬ment (based on International Standard ISO 2372). After¬wards, the vibration levels were recorded regularly using a vibration meter. The measurements were taken at all bearing

Jan 1, 2000

By Michael E. Kelahan, Glenn A. Gruber

A review of recent phosphate beneficiation developments shows that Flotaire cells, ranging from 0.20 m to 2.44 m in diameter, have been examined in pilot scale and commercial plants. Applications of the column cells have included sized feed fractions using anionic and cationic reagent systems. In plants where the Flotaire was installed as a test unit or as an optional circuit, its use has been largely discontinued. On the other hand, when management committed to installing the Flotaire as an integral part of the flowsheet, the performance expectations were met or exceeded.

Jan 1, 1988

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

The purpose of this work is to develop a conceptual recovery process for thorium dioxide (ThO2) from its primary source, monazite. The study-level design presented in this paper represents an economically viable method for conducting ThO2 extraction from monazite ore while also recovering byproducts that include P2O5 and other rare earth element oxides rather than producing unnecessary waste streams. Three key points to note in the development of this process design are: (1) the process economics relied heavily on recovery of rare earth byproducts, (2) the thorium handling portions of the process could effectively be segregated from the rare earth and phosphate handling portions of the process, and (3) the thorium and uranium content in waste streams should be carefully managed and eliminated where possible.

By Joachim H. Schubert, David G. Hulbert, Ian K. Craig, Roger G. D. Henning

This paper presents a stabilizing controller for flotation plants which uses a quasi-multivariable technique. The controller monitors all the levels in the plant, and by anticipating interactions between various parts of the plant, is able to stabilize the plant far more successfully than the normal plant control. Once stabilizing control has been achieved, optimization of the process becomes easier and more sustainable. An estimate of the improvement in metallurgical performance is made and a singular value analysis was conducted to verify that the multivariable algorithm will theoretically control better than a collection of individual PID loops. Metallurgical results are presented to show that the improvements are attainable in practice. Control by the Mintek algorithm was alternated with normal plant control, to show that the improvements are statistically significant.

Jan 1, 1995

By Richard Hogg, Erol Kaya, Jan M. Mutmansky

Characterization of the size, shape, chemical composition, and mineralogical content of mine airborne dusts generally requires a larger mass of dust particles than is typically collected using traditional sampling devices. In this paper, the general design of a passive dust collector is described and the field results are presented. The collector was constructed of galvanized sheet metal duct with a resin-coated honeycomb to provide an elutriation-type system for particle collection. Several versions of the collector were used in the field portions of the research. The dust samples collected from underground coal mines were found to possess angular particle shapes, relatively consistent size distributions, and elemental compositions that showed relatively little variation, at least for the more prevalent elements. In addition, the distributions of particles sizes obtained from the passive dust collector appear to be similar to those of samples collected at the same time in a conventional personal sampler except that the passive device seems to collect a larger quantity of coarse, non- respirable particles. Conclusions on the suitability of this dust collector for collecting characterization samples are presented. In addition, the potential for using such a dust collection system for supplying dusts for biomedical research is discussed.

Jan 1, 1993

By Misra M., P. Grimes, Chen. S.

The combustion of petroleum products produces emissions which contain oxides of nitrogen (NOx), hydrocarbons (HC), and particulate matter (PM) which have adverse health and environmental effects. In recent years there has been increasing interest in the use of water-fie1 emulsions as a substitute for conventional fuels. Emulsified fuels are emulsions of water in fuel, which are typically made of 10 to 20 percent of water mired with certain additives and fuel. Studies have shown that the emulsified diesel can significantly reduce the emissions of NO, PM and car- bon monoxide and increase the fuel efficiency. In order to produce a stable diesel emulsion, the development of an effective surfactant additive is critical. The stability of diesel emulsions is influenced by many factors, including size distribution of the droplets, the viscosity of the continuous phase, the physical properties of the interfacial film, and temperature. This paper describes a method to produce emulsified diesel and combustion results obtained from various tests. It has been found that the diesel emulsion made with this additive package was stable during the test, and the emissions were lower in NO, CO, and PM compared to the baseline diesel.

Jan 1, 2005

By Naj Aziz

Both bolt profile shape and spacing (rib spacing) have been found to influence the bonding capacity of the grouted rock bolt. The bolt surface profile configuration has greater importance to rock bolting in strata reinforcement in mining than the steel rebar used in civil engineering construction. This is because a rock bolt in mining usually is subjected to greater dynamic loading than the steel rebar in civil engineering construction. The increased bonding capacity of a bolt is important when supported ground is either heavily fractured, faulted or the supported ground is of soft formation, typically that of coal measure rocks. Past laboratory studies have identified the bolt profile spacing as of significant relevance to bolt resin rock bonding increase, however, no attempt has been made to determine the optimum spacing between the bolt profiles spacing. Accordingly, a series of laboratory tests were carried out on 22 mm core diameter bolts, commonly used in Australian mines, installed in cylindrical steel sleeve. The study was carried out using both push and pull testing methods. The push test was carried out in 150 mm long sleeves while the pull testing was conducted in 115 mm long sleeves. Profile spacing tested include, 12.5, 25.0, 37.5, and 50 mm lengths. Additional studies undertaken include modelling the profile of the load-displacement data of pull testing. Bolts with a profile spacing of 37.5 mm were found to provide optimum load bearing capacity as compared to other tested profile spacings.

Jan 1, 2009

By Vanessa M. Torres

Diagnostic leaching tests provide a good indication of gold deportation in its various occurrence phases. With the results of these tests, possible flowsheets for difficult ore treatment can be established for further evaluation and plant operation can be optimized. The use of this technique can be extended, including heap leach evaluation and complex copper-gold ores. The results on the use of diagnostic leaching tests in gold ores from Companhia Vale do Rio Doce (CVRD) are presented and discussed, as well as the methodology to select steps and interpret results used at CVRD Technology Center (Sutec).

Jan 1, 1998

By Shuang Shuang Huang, John Fillos

Ozonation was evaluated as an alternative treatment process for leachates of municipal landfills. The study was carried out on leachate from the Fresh Kills Landfill, New York City. The leachate has strong tea color and BOD5 ranging between 90 mg/L and 130 mg/L. The average COD, TOC and NH3-N concentrations were 1800 mg/L , 550 mg/L, and 665 mg/L, respectively. The kinetics of the process were studied in a sparged batch reactor by developing concentration- time profiles for residual color and TOC. Continuous flow experiments were then carried out at two selected contact times. The process was found to be effective in the treatment of leachates for color and TOC removal.

Jan 1, 1992

By B. Yarar, R. Buchan

Mineral-processing techniques were adopted for use in the separation of various plastics used in beverage bottles. A complete flowsheet, which utilized size reduction, heavy-media separation and flotation, was developed to separate PE, PVC and PET. In addition, the mixtures contained cellulose fibers (from labels) and aluminum (from bottle caps). It was demonstrated that, while heavy-media separation allows for the separation of a PVC/ PET mixture, froth flotation can be used to separate PVC and PET. For this purpose, the differential action of a pH 11 alkaline aqueous solution containing methanol and MIBC as surface-tension control agents, has been found to be a suitable flotation medium. This paper reports on some aspects of a flotation flowsheet that was developed for the separation of plastics contained in municipal solid wastes.

Jan 1, 1997

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

INTRODUCTION Conventional roof support methods such as mechanical and resin bolting provide adequate support for a wide variety of coal mine roof conditions. However, roof falls remain the single largest cause of death and injury in underground mines and seriously hamper production in many operations, demonstrating that these methods of roof support are not universally effective. One of the most recent and successful advances in coal mine roof control has been the introduction of the roof truss. Although past work on roof trusses (Gambrel1 and Haynes, 1970; Sheory, et al, 1973) shows little quantification of this support technique, numerous field examples have been cited where the truss effectively supported roof which could not be controlled by either mechanical or resin bolts (Kegel, 1969). The truss combines the advantages of both inclined roof bolts and post-stressing the roof. However, the full benefits of roof trusses will only be realized when design criteria to optimize support capacity are determined. The number of trusses required for a given roof condition can then be minimized, reducing installation time and making them economically more feasible. The purpose of this research is to develop roof truss design criteria based initially on laboratory studies of gravity-loaded multi-layered photoelastic mine models. Laboratory test results will then be modified where necessary following future field testing. The ensuing relationships should provide the field engineer with a reliable means of calculating optimum truss configuration, capacity, and spacing for a set of known roof conditions.

Jan 1, 1977

By John Durkin, Steven Wirch, Fred N. Kissell, Steven Ruggieri

The Bureau of Mines has developed two expert systems to give advice on coal mine dust control, one for continuous miner sections, and another for longwalls. Prototype versions have been evaluated by coal operators and MSHA. Both systems query the user as to the nature and extent of the dust control problem. Typical questions asked deal with matters such as cutting sequence, current dust standards and characteristics of current dust control techniques. Advice given by the system generally does not focus on a single issue, but may suggest a variety of approaches consistent with the ability of the operator to practically implement what is suggested. Both were written using expert system development software called Insight 2+. The advantages of Insight 2+ for the user are: low cost, IBM-PC compatibility, and the fact that little prior experience with computers is required. For the developer, Insight offers an easy to use production rule language and goal driven structure as well as a wide variety of capabilities.

Jan 1, 1987

By P. Somasundaran, A. Sivakumar

Surfactants and polymers are used in a number of processes such as flotation and flocculation. The structure of the adsorbed surfactant and polymer layers control the interfacial properties of the solid and hence an understanding of the structure of the adsorbed layers at the molecular level is essential. In this paper, a review of different spectroscopic techniques (fluorescence, electron spin resonance and Raman) used to characterize the adsorbed layers [in-situ] is presented. Information on the micropolarity, microfluidity and size of the surfactant aggregates was obtained and the growth of the adsorbed layer was followed. [In-situ] conformational states of polymers at the solid/liquid interface were determined for different pH values.

Jan 1, 1989

By B. P. Mohanty, D. A. Shores

During the induration of fluxed taconite pellets, alkali salts deposit on the grate support bars, causing severe corrosive degradation of these alloys. To determine the source of these deposits and to understand the mechanism by which the salts are conveyed to the grate bars, a study of the reactions between fluxed pellets and combustion gas was carried out. The study focused on the thermodynamics and kinetics of several processes associated with induration; namely, oxidation of magnetite, calcination of flux, and the formation and gaseous transport of various alkali salt species. Both theoretical and experimental techniques were used. It was concluded that the principal source of alkali salt deposits is alkali chlorides, which are present as contaminants in the flux and/or residue from contaminated washwater. The pathway from pellet to grate bar involves the following steps: evaporation of chloride salts within the pellet; diffusion of salt vapor out of the pellet, aided by the outflow of CO2 from calcination of the flux; convective transport by the combustion gas with concurrent (partial) conversion to alkali sulfates by reaction with residual SOX in the combustion gas; and condensation of salts on the grate bars.

Jan 1, 1998