Search Documents

By Takeshi Tanaka, Yasuhiro Komamura, Yuusaku Tominaga, Takayoshi Iwamoto

In order to assist better countermeasures for ventilation control in normal/abnormal condition of mine ventilation network in real time, branch relation table derived from a macroscopic characteristic of ventilation network is introduced in this study. The main results in this study are as follows; 1) One of macro characteristics of a ventilation network, as a relation between airflow rates in two branches chosen arbitrarily, is specified under the change of aerodynamic resistances in a branch. Airflow rate in a branch can be estimated by airflow rate in other branch changing aerodynamic resistance by using empirical formula. The empirical formula by computer simulation of the Horonai coal mine, Japan is considered to be a one-valued function with monotone or extremums. 2) A branch relation table shows the macro characteristics, mentioned above, of all the set of two-branch combinations in a network. Elements in the table give both information of control possibility range of airflow rate and total number of extremums in an empirical formula. 3) It is important that when aerodynamic resistance change in a branch is estimated by measuring airflow rates in two typical branches, the two branches should be chosen from branch combinations with monotonous relation in the branch relation table. 4) A flexible expert system to assist ventilation control in the specified branch in real time has been developed by using a branch relation table for a ventilation transfer diagram of the specified branch, such a coal face and an advancing face. A fuzzy reasoning is utilized in the recognition of the safety factor, methane concentration, in the system. And when conviction degree in recognition for methane concentration at the specified branch is too low, the system searches for other branch combinations in the branch relation table stored in the system, to use other ventilation transfer diagram of the specified branch. When a needed ventilation transfer diagram is not stored in the system, the expert system asks automatically the ventilation simulation from other computers linked to the main computer automatically. The system repeats consultation until conviction value of safety in the specified branch approached

Jan 1, 1993

By Michael J. Shulman

During-all phases of exploration limited resources must be allocated among exploration methods and among exploration prospects. This problem,, an exercise in optimization, can be treated mathematically. For three objective functions - maximizing return, return to cost and return minus weighted cost - theoretical results exist which enable the exploration planner not only to gain valuable insight into the problem, but also to estimate the resources necessary and to allocate these resources for' at least-two stages of exploration prior to initial field work. A two-stage exploration strategy for volcanogenic-sedimentary iron in northern Egypt illustrates, how the results can be used. Stage 1 consists of an aeromagnetic survey to map the structure of five areas;" stage 2 consists of field reconnaissance work. For the three objectives, lower bounds are calculated as a function of exploration expenditures for each stage in order to facilitate the choice of an-optimal exploration budget. Nomograms are then presented which, based on the Kuhn-Tucker Conditions', enable the incremental allocation of airborne and reconnaissance effort among the five areas.

Jan 1, 1989

By J. J. Kellar, W. M. Cross, J. D. Miller

Infrared spectroscopy has been one of the most useful experimental techniques for the analysis of surface reactions in flotation systems, including surface alteration and surfactant adsorption reactions. With the advent of Fourier transform infrared (FTIR) spectrometers, many low-energy throughput IR experimental techniques previously unused by flotation researchers have come into greater use. In particular, internal reflection spectroscopy (IRS) is the most often used technique for in-situ studies. To date, three IRS methods have been used for in-situ measurements. These techniques are evaluated for use in characterization of surface reactions in flotation systems. The method using mineral crystals as reactive internal reflection elements (IRE) is of particular interest because it allows surfactant adsorption densities to be calculated directly from in-situ spectral data in real time. Application of in-situ FTIR/IRS with reactive internal reflection elements will be demonstrated for collector adsorption reactions in each of the major flotation systems. The alumina (A1203)/sodium dodecylsulfate system is used as an example for insoluble oxide/silicate flotation, while the fluorite (CaF2)/oleate system serves as a paradigm for semisoluble salt flotation. For sulfide flotation, sphalerite (ZnS) is used as the reactive IRE with potassium amylxanthate and potassium ethylxanthate as collectors. In the case of soluble salt flotation, sylvite (KC1) is used as the IRE with n-octylamine as collector. Finally, the use of reactive IREs in the near-IR spectral region and in spectroelectrochemical research is discussed.

Jan 1, 1989

By Shinya Ono, Tsuyoshi Katoh, Yuusaku Tominaga

In order to monitor/control airflow rate distribution in a complicated ventilation network installed many regulators, an integrated system composed of expert system, exerting programs for simulation to get macroscopic characteristics and drawing diagram, monitoring system and so on is introduced in this study. This system is made up of airflow velocity sensors and computers linked to an local area network. The main results of this study are as follows; 1) Combinations of two branches to monitor aerodynamic resistance change in a branch p in a network can be selected by comparing factor's value in a branch relation table. 2) When the combination of sensor branches for a branch p does not exist in the network at present condition, the system changes aero- dynamic resistances of appropriate branch q placed a regulator by referring branch relation table. And then the system asks other computer to get macroscopic characteristics under altered value of aerodynamic resistance of the branch q. 3) Dot pattern diagram shows airflow rate relation between an active branch and a passive branch. Three relations such as a) a straight line, b) a monotonous curve and c) extremums are displayed in different patterns for all the sets between an active branch and a passive branch at a time. 4) The ranges of airflow rate in coal faces by changing aerodynamic resistance of any one branch placed a regulator are shown in the Pareto diagram using values in the branch relation table. 5) Ventilation transfer diagram with two parameter, one shows airflow rate in a coal face and the other shows energy provided by main fans to overcome aerodynamic resistance in a net- work, is utilized to decide countermeasures for decreasing energy consumption in the network on increasing of airflow rate in the specified branch.

Jan 1, 1995

By William F. Eichfeld, Robert J. Wenzel

INTRODUCTION The phrase "subsidence control planning" can refer to the use of specific mining methods and-specialized techniques to control subsidence events or it can refer to planning for subsidence by predicting its magnitude and timing and further planning mitigation strategies. In the first case the objective is actually subsidence prevention while in the second it is a design procedure that seeks to maximize the use of both surface and subsurface resources. Neither technology is well developed at this point. The purpose of this presentation is to briefly outline the Department of Energy's Subsidence Program. This program is, in general, bases on the premise that subsidence control technology, by any definition, can be accomplished only through a thorough and rigorous understanding of subsidence phenomena. This understanding must come from many well planned and executed studies of stress redistribution and strata deformation as they occur during mining activities. There is presently considerable incentive to improve our subsidence engineering capabilities due to the desire for increased coal utilization with acceptable environmental impact. Considerable research in this area is being sponsored by federal and state governmental agencies, universities, and the coal industry. Federal sponsorship has been borne by the Department of Energy, the Bureau of Mines, the Office of Surface Mining and the U.S. Geological Survey for the most part. These agencies have carried out basic research in their laboratories and have contracted with other organizations for additional work. At this time most of the available resources are directed toward contract research, especially in DOE. It is the DOE research plan which will be addressed here.

Jan 1, 1982

By Luís Tavares Ribeiro

Nowadays there is a greater need for detailed reservoir modelling in the oil industry. It is generally recognized that nearly all reservoirs are heterogeneous and idealization of rock characteristics in flow calculations is unrealistic regarding actual physical and textural conditions encountered in geologic formations. The heterogeneity of oil reservoirs considerably influences the distribution of fluids, as well as their displacement. It would be advantageous if a reservoir petroleum engineer was able to construct a precise mathematical model of the detailed reservoir rock variability characterizing the degree of reservoir heterogeneity in an unambiguous way. This paper presents a geomathematical model describing the spatial behaviour and distribution of the principal reservoir properties. The model is based on the Theory of Regionalised Variables and the Kriging technique. The model is performed by a set of computing programs and is tested on an Abu Dhabi oil reservoir in United Arab Emirates.

Jan 1, 1986

By C. I. Basilio

The adsorption of O-isopropyl-N-ethylthionocarbamate (IPETC) and O-isobutyl-N-ethoxycarbonylthionocarbamate (IBECTC) on chalcocite, chalcopyrite and pyrite has been studied using UV and in-situ FTIR~ATR spectroscopy. Thionocarbamates were found -to adsorb strongly on chalcocite at pH 4-10, but consider-ably less on chalcopyrite and pyrite. The FTIR spectra show that the surface species of thiono-carbamates are bonded to metal atoms on the mineral surfaces. However, at high concentrations, IBECTC also forms physically-adsorbed species. Adsorption of these thionocarbamates cannot remove or prevent the formation of sulfoxy oxidation products on pyrite, unlike the case with the xanthate-pyrite system. This finding may account for the observed flotation selectivity of these reagents against pyrite. The spectroscopic information is compared with flotation test results.

Jan 1, 1988

By A. E. Koski

This paper will review recent developments in the area of mine planning at the Empire Mine. It illustrates how one of the largest iron mines in North America has adapted computerized mine planning to meet the unique requirements of their mining operation.

Jan 1, 1994

By Robert A. Metz

During the past decade we have witnessed spectacular improvements in productivity of open pit mining equipment. Thousand-horsepower engines, 200-ton trucks and 15-yard electric shovels, which such a short time ago were just dreams on a drawing board, are now realities. More productive equipment and metal shortages have encouraged increased production at existing mines and the development of new larger tonnage operations. Operators and engineers have been able to employ computers and various other types of automation to "stay on top of things". The mine geologist, however, is merely faced with a bigger and more rapidly changing pit to pick in. Keeping geologic information current in these mines presents entirely new problems to mine geological staffs. To obtain adequate geologic information on the developing orebody requires enlargement of the staff to share the work load or revision of methods in keeping with the times. The former has the disadvantage of loss of the comprehensive knowledge of the pit that a chief geologist likes to have, not to mention management's usual lack of enthusiasm for force increases.

Jan 1, 1970

By Jr. Stokowski

Topsoil for revegetation projects is in demand in many urban areas. In this case history, a large aggregate producer manufactured a topsoil from three waste materials. The topsoil was produced in a 200,000 m2 (50-acre) abandoned gravel pit that still had additional gravel under 10 m (30 ft) of overburden uneconomic to strip directly. The topsoil was produced by rotary mixing of sludge, overburden, and a lime admixture; solar drying; and stripping and stockpiling of the product. A major problem was an increase of topsoil drying times for stripping from 40 to over 100 hours when it was rewet by storms. The problem was solved by a research project that evaluated over 50 formulations and over 20 waste materials. . The final formula dried in 15 hours and contained 3-parts sandy mine spoil, 1-part sewage sludge, and 2 % spent-bed, a granular quick-lime produced during power-plant flue-gas desulfurization.

Jan 1, 1988

By M. Gaft, G. Panczer, R. Reisfeld, L. Nagli

Laser-induced luminescence and breakdown spectroscopy methods appear to be a good tool for real-time evaluation of dolomite content on moving belt. The distinctive feature for time- resolved luminescence is Dy3+ emission in apatite, which is excited by 251 nm laser light and detected with delay time of 5 ms and gate width of 1 ms. The distinctive features for breakdown spectroscopy are 604 nm line of F and P in apatite and 518 nm line of Mg in dolomite. The representative sampling of more than 200 pebbles has been studied by both methods. By luminescence method 100% of dolomite will be identified, while approximately 15-20% of apatite with extremely week Dy3+ luminescence may be mistakenly counted as dolomite. By breakdown spectroscopy the identification is 100% correct both for dolomite and for apatite.

Jan 1, 2002

By T. J. Carew

INTRODUCTION The application of micro-computers to the evaluation of an advanced exploration project is illustrated by reference to a large project in the Sudbury Basin region of Canada. The deposit in question is polymetalic (Cu, Pb, Zn, Au, Ag) with a strike length of 3048m (10000ft) and has been explored to a depth of 457m (1500ft) by approximately 1350 diamond drillhole of between 9 - 305m (30-1000ft) in length. The large amount of data involved and the ability to rapidly recalculate geological reserves in response to fluctuating metal prices were key factors in the application of a micro-computer based evaluation system. The evaluation software was implemented at two levels, with data capture implemented mainly on - an entry level workstation comprising an IBM-PC compatible (PC-XT) micro-computer equipped with a 20Mb hard disc, printer and RS-232 serial communication facilities. Data analysis, display, geo- logical modelling and processing was carried out on a high-level workstation based on a Hewlett-Packard 9000 super- micro computer and peripherals, including a 40Mb hard disc, tablet digitizer and plotter. Basic drillhole data was entered either directly at the super- micro or transferred from the PC via the RS-232 link. The evaluation process proceeds once the data is edited and in a "clean" format within a master project database. The software is comprised of a suite of modular, integrated programs based on ease of use, interactive graphics and optimized for the computer workstation. Drillhole data was displayed and plotted as hard copy plots on which geological interpretations were developed. The data was copied into small manageable projects consisting of 100 to 150 drillholes, within which a sectional model was created such that all the models are interconnected along the entire strike with no overlaps. Geological reserves were derived by developing a set of function variables, including Net Smelter Return, within the database. The values of these functions can be displayed on the model sections and "ore” zones defined in accordance with pre-determined cutoff values. Interpolation of the modelled data was then carried out and geological reserves calculated and reported. DATA CAPTURE Drillhole data for the project consisted mainly of existing drillhole logs, although the system allows for the entry of new information as it becomes available. The structure and format (i.e. number and length of variable fields) is user defined. The log for this project comprises an abbreviated section for name, competency, grain size, texture, colour and alteration. Fields are defined for structural information regarding bedding and fault angles and up to seven mineral identification columns and percentages are available. Assay information consisting of the sample number, width and six determinations (Cu%, Pb%, Zn%, Fe%, Au opt., Ag opt.) along with a comments section of 25 characters completes the log. One powerful feature of the data- base is the ability to set up function variables that are mathematical and/or logical combinations of the project variables, enabling the user to develop economic variables such as Net Smelter Return. These functions include current treatment costs, deductions and penalties and can be rapidly recalculated within the database to accommodate changes in metal prices, forecast recoveries and exchange rates (Table 1).

Jan 1, 1987

By M. R. Fletcher

Slags generated by the ferrous-metals industry can be used to produce high-tech ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted and formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost wear-resistant tile material which can be custom cast. This and similar materials, made from slags and natural rocks, are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1988

By R. C. Runvick

Gypsum resources are significant in the midwestern United States, with specific deposits varying in "place value" relative to the major markets served. Underground and surface mining operations produce gypsum from sedimentary rocks ranging in age from Silurian through. Jurassic. Although reserves tend to be limited at individual operating properties, potential resources are vast and future development will hinge principally on market growth and changing economic conditions. Most critical of the variables affecting the industry in both the short and long term will be the availability, type and cost of energy and both processing and distribution.

Jan 1, 1980

By P. L. Webster, S. D. Thompson

The Coal Mine Belt Capacity Simulator (CMBCS) was originally developed to provide an improved belt capacity simulation through more detailed, flexible and realistic modeling of belt loading. While this model offered improved capacity design for conveyor belts and surge bins, it lacked the capability to simulate some key protection and segregation applications for bunkers. Recently, CMBCS was extended so that these latter bunker applications could be considered. In addition, a fear minor extensions were made to improve the model's flexibility and of efficiency. These various extensions and the steps taken to verify and validate them are described. The associated modifications in the model's input and output as well as the model's current requirements and availability are also discussed.

Jan 1, 1992

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative's 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By D. W. Alexander

Mine fires, explosions, spontaneous heating and inundations are among the leading causes of catastrophes (unplanned, temporary sealing and recovery of major mines). Many reports are available that detail company efforts to re-establish mining operations and agency efforts to regulate away the causes, but the associated costs are rarely included. The increasing scale of coal operations concentrates earning potential and the financial risk of business interruption in fewer locations. Underground coal mine catastrophes are low probability, high loss events that happen nearly every year. This paper will present an evaluation of coal mine catastrophes from case studies.

Jan 1, 2003

By L. A. Morley, S. C. Gambrell

Behavior of a jour-leg shield design used on a soft floor in an operating longwall system is presented. The shield examined in this study was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the magnitudes of typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments required to produce the deformations are calculated based on the mechanical properties of the material. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1991

By Fathi Habashi

OXIDE ORES can be divided into two groups: 1) Simple oxides (Table 3.1). 2) Complex oxides. Those ores containing minerals composed of two oxides; an acid oxide (Cr2O3, Nb2O5, etc.), and a basic oxide (CaO, FeO, MnO), as shown in Table 3.2.

Jan 1, 1970

By Tad S. Golosinski

The paper presents the computing stream of the mining engineering curriculum at he Western Australian School of Mines (WASM), a branch of Curtin University of Technology. Learning to use computers begins during the first semester of the initial year of studies and culminates in the Mine Design Project done during the last semester of study. It covers all areas of computing which are judged to be of importance to the graduate.

Jan 1, 1996