Search Documents

By Roger L. Baer

Introduction Brief Review -SEC mission & history -Development of SEC mining disclosure guidelines -Principles of good public company ‘disclosure’ SEC staff views of alternative approaches to mining company disclosure -SME Resource & Reserve Committee – April 2003 Food for thought

Jan 1, 2003

By J. Raatikainen, I. Auranen

"INTRODUCTION Sorting technology has advanced rapidly recently. Of the two possibilities particle sorting has advanced especially in introducing new sensors and the use of multiple sensors. The analyzing and computing lead times have also shortened. This has made it a viable technology option for many applications but not for the most important sorting task at a mine; the run-of mine ore. Bulk sorting, however, has advanced in smaller steps, even if the technology has the capability to tackle the run-of-mine ore and offers a high potential to bring mines substantial economic benefits. The sensors, which are useful are restricted by the difficult operating conditions or by the ore characteristics. One of the important features of run-of-mine sorting technology is the major material handling infrastructure required. The capital expenditure can be substantial requiring good understanding of the sortability curve (grade-recovery curve) behavior of the ore. This paper discusses one industrial case, where substantial amount of data measured from the ore feed belt has been obtained. This data was then analyzed for the grade recovery curves obtainable from that ore with sorting. EXPERIMENTAL The XRF measurement used was the FCA device from IMA Engineering (Fig.1). It is a specially built version of XRF designed to operate with coarse material. The measurement was situated at the main belt conveyor taking ore from the primary crusher to the stockpile. The crushed ore was about 80% -300 mm at a capacity of 1100-1200 tph (Fig.2). Measurement times were varied from 30 seconds to a minute. Measurements were obtained over several months.As the XRF is a surface distribution measuring technique, the measurement was first tested upon accuracy and reproducibility against plant daily wet chemical assays and against on-line Courier feed analysis. As there is a varying delay in the ore stockpile, the delay time was used as a variant in the validation. Different measurement times were tested for accuracy. A one minute measurement time gave a total measurement relative standard error, which was both for Cu and Ni below 3%. The results showed also very robust correlations; for Cu, the correlation coefficient was R > 0,94 for one minute measurements over three months and R > 0,86 for Ni respectively. Fig 3. Shows a measurement period of two hours showing substantial feed grade variations (given as relative value; 1.0 represents the mean value during the measurement month)."

Jan 1, 2018

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

Today, approximately 31% of underground coal mining operations have designated occupations or areas with more stringent (below 2.0 mg/m3) respirable dust standards in place. Many U.S. coal mines have been able to maintain compliance with very low dust levels, and the Bureau of Mines, in an effort to identify those factors contributing to low dust levels, completed a survey of twelve continuous miner sections which were able to maintain their dust levels at or below 0.5 mg/m3. The quantity and quality of face ventilation appeared to be the most important factor in controlling dust exposure. The results directed Bureau research towards identifying improved face ventilation techniques for reducing quartz dust levels on continuous mining operations. This research has involved the evaluation of a half-curtain face ventilation technique which reduces the cross-sectional area of the entry, thus increasing the air velocity over the operator. The Bureau has also conducted extensive laboratory studies to compare tubing versus brattice, including an evaluation of both systems in a crosscut turn. In an effort to improve ventilation and reduce dust exposures of roof bolter operators working downwind of the continuous mining machine, the Bureau has evaluated two novel face ventilation systems. The first system consists of a fan discharge tubing technique which routes dusty air away from the return entry being bolted. In a technique similar to the fan/tubing concept, exhaust air from the upwind continuous miner face can be scrubbed using a dust collector to capture a portion of the dusty air, clean it, and supply it to the bolter operators as a split of clean intake air. A better understanding of face ventilation techniques should lead to solutions to the problem of more stringent dust standards due to quartz.

Jan 1, 1989

By J. S. Stachulak

Installation of a computerized mine monitoring and control system in two planned construction phases began in 1983. Phase one consisted of providing a central monitoring station located on surface for monitoring underground CO detection in Frood Mine's heated area. The implementation of this project annualized labour savings of $200,000. The cost of installation of an early fire warning system was $100,000. There are several CO sensor monitoring carbon monoxide trends through mine heated areas. To obtain an early warning, it is not good enough to know that a fire has started, but it is also necessary to know where the fire is located.

Jan 1, 1989

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By J. D. Forrester

In striving to develop this discussion about "Manpower for Industrial Mineral Industries" two fundamental classes of manpower are encountered. These are: 1) The Labor Force, comprised of unskilled and semi-skilled, nonprofessional personnel who participate in conducting economic, mineral deposit operations and; 2) The Professional People involved in the science, engineering, and management of such industrial enterprises. The commentary given here will be directed primarily to a review of the characteristics of the second or latter class. To pursue successfully a career as a scientist or engineer in today's industrial and social complex, it is necessary that technical knowledge must have been acquired by training and study in an institution of higher learning. Also, to act effectively, the individual must have achieved some degree of specialzation, although this element often is developed to most notable degree by post-graduate exposure and experience. In addition, and especially in the case of "management," it is desirable, indeed it is even necessary, that an individual recognize and appreciate the fundamental humanistic-sociological controls, and their nuances, as these elements exist to shape his total environment.

Jan 1, 1969

By J. C. Yingling, R. Kumar, J. Sottile

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and, thereby reducing processing costs, recovery losses and refuse-genera¬tion levels. In this paper, new ap¬proaches for optimal control of the segregation process using time-se¬ries models and empirical distribu¬tions are presented and demon¬strated using field data.

Jan 1, 2000

By Y. K. Yen, J. D. Miller, C. L. Lin

Particle size segregation is a common phenomenon in many particulate processes and has many undesirable effects. The size segregation which occurs on a belt conveyor causes a serious problem for on-line particle size measurement using image-based techniques. Whether particle size distributions measured from the top layer of the belt are representative of the total particle population is largely dependent on the degree of size segregation. Therefore, it is important to understand the nature of such size segregation in order to make appropriate corrections for on-line particle size analysis. Monte Carlo simulation has been used to provide segregation information on particles with simple geometry and the results can help to determine important factors in experiments with irregularly shaped particles. It is expected that the relationship between the particle size distribution of the top layer and that of the entire particle population on a belt conveyor can be formulated as a model based function.

Jan 1, 1997

By Richard L. Breithaupt

INTRODUCTION A shuttle car is a self-propelled rubber-tired haul¬age vehicle designed specifically for underground min¬ing, primarily in coal mines (see Figs. 1 and 2). The drive mechanism is located on the sides of the vehicle, and the load is carried in the center. A chain-and-flight conveyor distributes the load when the car is being loaded by a loading machine or continuous miner and also discharges the load onto a conveyor belt or into a mine car. As the name implies, the shuttle car shuttles back and forth between the working face and the un¬loading point and is not required to turn around. Shuttle cars have served as primary haulage in this country since 1940 and still perform this function in most coal mines today. TYPES OF SHUTTLE CARS Shuttle cars may be battery-powered, diesel-powered, or cable-reel electric powered. Battery-powered cars were used between 1940 and 1950, but are almost out of existence today because of their limited power. Diesel cars have been used in coal mines, but are used mostly in noncoal mines where rules and regulations are not as stringent. Also, objections by organized labor have limited the use of diesel-powered shuttle cars in coal mines. Today, the largest number of shuttle cars are cable-reel cars. Electric power is fed through a cable stored on a cable reel that may have a capacity from 152 to 244 m (500 to 800 ft), depending upon the size of the cable and the cable reel (see Table 1). This, of course, limits the travel of a shuttle car. However, time studies have shown that for the most efficient haulage cycle, the length of haulage should not exceed 91 m (300 ft). As haulage distance increases, the waiting time for the loader or miner becomes longer, and haul¬age efficiency suffers. Cable-reel cars are manufactured in standard hand and opposite standard hand models. A standard car has the operator's control on the left front side and the opposite standard car has the opera¬tor's controls on the right front. Generally a loader or miner operates with two shuttle cars, one of each type. This allows the trailing cable to lie on either side of the entry and prevents the cables from fouling each other. Shuttle cars are designed to operate with either dc or ac power. Cars using dc power are designed for 250-v supply and ac cars are designed for either 440, 550, or 950 v, three-phase voltage. Most coal mines that are relatively level can use dc cars where dynamic brak¬ing is not required. For mines having steep grades (in excess of 15%) ac cars are used because ac traction motors have inherent dynamic braking and are safer when tramming downgrade. A recent innovation in shuttle car design in the last five years has been the introduction of an ac/dc car. This design utilizes ac input power through the cable, and the power is rectified on the car to 250-v do for traction motors. The pump motor and conveyor motor are powered by ac voltage. The main advantage of this design is efficiency-a much smaller cable may be used and the smooth operating characteristics of the dc traction motor is obtained. This prevents shock loading on the traction drive train, which is an undesirable feature of ac traction motors. SHUTTLE CAR FEATURES Elevating Discharge Today, all shuttle cars are equipped with an elevating front conveyor that allows the shuttle car to discharge into a mine car or belt feeder without the use of ramps. Hydraulic Power System Today, all shuttle cars are equipped with an hy¬draulic power system. An hydraulic pump is driven by an electric motor which provides hydraulic power for steering, elevating the front conveyor, and powering the

Jan 1, 1982

By Philip L. Hageman, Paul H. Briggs

An important tool for use in the geochemical assessment of abandoned mine-waste piles is a leach procedure that can easily be done in the field and used for on-site screening of historic mine-waste material. We have developed a simple field leach test that is an effective indicator of waste pile geochemistry and can be used in order to establish the relative geochemical fingerprint for a given pile. This simple procedure also provides indication of the potential chemical composition of run-off from the weathered surface of these piles. As part of developing the technique, a comparative study was carried out on eight mine-waste composite samples from different deposit types. Splits of all eight composites were leached using the field leach test procedure and a modified version of EPA Method 1312 (SPLP). We found that the field leach test consistently provides relative indication of leachate geochemical trends comparable to leachate data derived from the more regulated, time consuming and laborious EPA Method 13 12 (SPLP).

Jan 1, 2000

By A. B. Holland-Batt

In the 1960s and 1970s, incremental development rather than innovation was the norm for gravity separation. However, the last 15 years have seen a number of new developments in this area. The article reviews the traditional gravity-separation techniques and then examines the newer developments such as centrifugal separators. Emphasis is placed on novel devices or improvements that offer better control or improved performance.

Jan 1, 1998

By Jianmin Qin, Raja V. Ramani

In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration.

Jan 1, 1995

By H. Sis, S. Chander

The pressure filtration behaviors of dispersed and flocculated alumnae slurries at high percent solids were investigated with the objective of determining the effect of surfactant type and concentration on slurry properties. A high-purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by pH and by surfactants that are known to act as electric and steric stabilizers. The effects of both ionic and nonionic sutfactants were investigated. Surface charge measurements of the slurries were carried out by an electrokinetic sonic amplitude (ESA) method to better understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and cake properties are discussed.

Jan 1, 2000

By Neal P. Cochran

The Office of Coal Research Program has been outlined in our Annual Report for a number of years and reported on by various members of the OCR staff as well as by our contractors. The program is national in scope and is intended to develop new and improved uses for our Nation's coal resources and to maintain coal in a favorable economic position, vis-a-vis, the other energy forms. A program has been developed that includes conversion of coal to gas, gasoline and other petroleum-type products, and to electricity. These projects are only one facet of the OCR program albeit an important one. In many of the conversion projects we have underway, original development work has been done with bituminous and sub-bituminous coal. It is the intention of this paper to present a general outline as to how lignite might fit into one or more of these projects as a raw material. Our national lignite reserves are vast in scope and this has been recognized in the OCR program by development of a project specifically for lignite and by including lignite as a test raw material in many other projects. Project Lignite is intended to develop the Cop Acceptor Process for conversion of lignite to a high B.t.u. gas. In this effort we have included the design, construction, and operation of a lignite gasification plant at Rapid City, South Dakota. The work is being conducted by the Consolidation Coal Company and is an outgrowth of their laboratory development of this process. The first portion of our effort included a detailed economic study of a somewhat arbitrary grouping of States designated Market Area A that could be expected to use gas manufactured in a lignite gasification plant. The area included the Dakotas, Minnesota, Nebraska, and Iowa. This geographical area could readily be served if a process could be developed for converting North Dakota's lignite reserves, estimated at 351 billion tons, to high B.t.u. gas. Our study showed that Market Area A had a potential commercial- industrial market of one trillion cubic feet of gas a year. To meet this demand, we believe that part of the load can be obtained from commercial lignite-to-gas plants. At the time of our original study, we concluded that gas could be delivered to the city gate in Market Area A at about 45¢. As a result of price escalation in the interim, our estimate today might be slightly higher, but not significantly so, since some parts of the process appear better today than they did at the time of the original projection.

Jan 1, 1968

By J. Bouchard, V. Aubé, A. Desbiens, R. del Villar

The metallurgical performance of column flotation is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a method to get froth depth and bias measurements using virtual sensors. Fractional factorial experiment design for the neural network calibration of the bias sensor, pilot plant results, and eventual industrial applications – including the possibility of achieving effective real-time optimization from bias and froth depth measurements – will also be discussed.

Jan 1, 2003

By V. F. Swanson

A mathematical model for free and hindered settling of minerals was developed. This paper describes how to apply the model in designing systems, such as fluidized bed, elutriation, mixing pumping systems, involving solids and fluids.

Jan 1, 2000

By Barton Kelby Cross

In the early 1960's the feasibility of mathematical modeling was demonstrated in Northern Rhodesia and southwestern United States, where techniques were developed to use these models in a new approach to aid engineers in the estimation of ore reserves, mine designs, and financial evaluations. These rudimentary models closely followed the manual methods, producing ore reserves and production schedule estimates that were as accurate as the manual methods, yet were many times faster. Mines evaluated and designed using these new tools gradually came into operation during the 1970's and entered the phase at which production scheduling and ore-grade control became day-to-day problems. Management expected the number of operational engineers to be small because small planning engineering staffs had produced the original designs and operated the smaller high-grade pits. Unfortunately, the tools needed by the mine engineer to perform short-term production scheduling and ore-grade control were labor intensive; they had not yet been generally computerized. Several attempts to use the original or exploration model for these two functions were futile. While an exploration model based on data from exploration work proved sufficiently precise for overall mine design and long-term production scheduling, the model lacked the precision required for short-term scheduling and grade control.

Jan 1, 1979

By P. R. Khangoankar, S. Devasahayam

An experimental study of the particle charac¬teristics of the magnesium carbonate crystals formed by the reaction between magnesium chloride and sodium bicarbon¬ate at different temperatures is described. The rate of growth of magnesium carbonate crystals for any constant tempera¬ture is established, and this rate of growth is related to the degree of supersaturation at the given temperature. The activation energy calculated using empirical constants de¬rived from the relationship between the crystal growth rate and supersaturation, is indicative of a surface-reaction mechanism.

Jan 1, 1996

By Andrew Neale, Ari Supomo, Mike Mular, Rob Perry

A method is presented to measure and correct the performance of regulatory control loops. Freeport Indonesia treats over 220,000 dmtpd of copper-gold ore in a complex of four concentrators. More than 400 regulatory control loops are implemented throughout the operation. The performance of each loop is quantified by an index based on its time in automatic, the deviation of the measurement from the setpoint and a metallurgical assessment of its impact on overall plant operation. Index values are recorded in a plant-wide data acquisition system and analyzed to produce a report of loops requiring attention. Loop statistics are analyzed to show if the problems can be corrected with tuning. The practical application, benefits, management and staffing requirements of this method are discussed.

Jan 1, 2000

By J. R. Sturgul

Computer simulation models of working mines can be a great benefit to mining engineers. Such models have been used in mine planning (how many trucks-shovels to have, when to add new equipment, etc.) and mine design (should a dispatch system be purchased, where is the optimum location, for mine equipment, etc.). A simulation model can be thought of as a dynamic representation of the mine. It can be easily changed to reflect a variety of situations. A major problem for the engineer is how to present the results of the simulation study. This has now been overcome by means of animation to present the results of the simulation. The main simulation languages in use for discrete system simulation are SLAM, SIMAN and GPSS/H. Each has animation with SLAMSYSTEM for SLAM, CINEMA for SIMAN and PROOF for GPSS/H. Animation with SLAM and CINEMA have been on the market for several years whereas PROOF is a relative newcomer and has features not found in other animation software. This discussion will be confined to PROOF. Some of the comments will apply to all simulation and animation software.

Jan 1, 1995