Search Documents

By R. A. Speirer, T. C. Bettinger, L. P. Richardson

INTRODUCTION The Bureau of Mines (The Bureau) remote sensing researchers at the Denver (CO) Research Center, have been investigating computerized methods to detect and map surface linear features called "lineaments" for ground hazard assessment in mines. Many of these lineaments at the test mine site were found to correlate to subsurface geologic discontinuities such as faults, fractures, and joints that intersect coal seams at depth. These features adverse1 y affect the roof and rib integrity in underground mines, thus contributing to rock failures that may result in injuries to mine workers and loss of production. Advance knowledge of the existence of such hazardous geologic features can aid in mine planning and development. Lineaments may be observed in a variety of images of the earth's surface. Linear features that can be observed using Landsat mu1ti spectral scanner data (MSS) images range from regional (greater than 3 miles in length) to an intermediate length of from 1 to 3 miles. These images are recorded in discrete radiation bands in the green, red, and near-infrared portions of the el ectromaynetic spectrum. These data are acquired from the EROS Data Center of the U.S Geological Survey, Sioux Falls, SD, in digital format on magnetic tapes that are suitable for processing on certain minicomputers. Shorter lineaments length (less than 1 mile) can be observed in high- to low-a1titude aerial photography, radar, and infrared images with image scale ratios of 1:1,000,000 or less. These linear features can correlate to smaller dimensioned faults, and to fracture and joint sets at the local geologic scale. Other informational sources can help substantiate 1ineament analyses, such as well logs, mine naps, topographic data, and geophysical data acquired over the study site. These data must be in a digital format to process on the "DEC PDP 11/23 minicomputer system1". Data can be acquired in

Jan 1, 1986

By H. E. M. N. Moursy, M. N. Ahmad, C. R. Holland, G. M. Walker, R. D. Chandler

This work describes the effect of process parameters on the acidulation of Moroccan phosphate rock using nitric acid, i.e., the nitro-phosphate process. A series of bench scale experiments were conducted, using a stirred tank reactor (STR) system, to investigate the chemical reactions involved and optimum conditions for the formation of nitro-phosphate fertilizer. The effect of reaction time, temperature, mixing speed, acidulation ratio, and acid concentration were investigated, and were found to have an effect on the dissolution of P2O5 from the phosphate rock, using nitric acid. An increase in nitric acid concentration resulted in an increase in P2O5 dissolution, however, the dissolution was also found to be a function of acidulation ratio. A nitric acid phosphate rock ratio of 4:l ensured 90% dissolution for nitric acid concentration > 30%.

Jan 1, 2002

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By S. P. Mehrotra, P. C. Kapur

A phase-species classification is suggested for the mathematical models of flotation kinetics. Important models are discussed and the structure of their rate constants and parameters is analyzed. Split or enhancement factors are formulated for different kinetic models. The steady state dynamics of the flotation circuits can always be described in terms of these factors. For simulation of circuits, feed is characterized in a formal manner starting from a multivariate distribution of particles in flotation rate, size and mineral content. Synthesis of optimum circuits which simultaneously searches for the best process variables and structural parameters from a generalized master network is described. Trends in the areas of search algorithms, role of middlings and feed identification etc. are indicated.

Jan 1, 1989

By J. H. Tylczak, R. Blickensderfer

Impact and abrasion properties of various commercial US grinding halls were evaluated and compared by the Bureau of Mines, US Department of the Interior. Laboratory tests were conducted on balls obtained from eight major US manufacturers. The halls included forged steel, cast steel, and alloyed white cast iron and were subjected to repeated impacts until they broke or until 300,000 impacts were exceeded. Pin abrasion tests also were conducted. The results showed wide differences in impact lives, ranging from a few thousand to over 500,000 impacts. The life of inferior commercial halls was increased five to six times by a laboratory tempering heat treatment. For halls that did not break, the major impact wear mode was spalling and ranged from an average rate of 0.28 to 4.46 mg per impact. The softest halls (steel) had excellent impact resistance but low abrasion resistance. The abrasion resistance of the steel halls generally increased with hardness. The alloyed white cast irons had about twice the abrasion resistance of the steel halls. Users should become aware of the wide variations among commercial halls, and ball manufacturers should be aware that their product can he improved.

Jan 1, 1990

By H. T. Miller, L. M. Scott

Radiation exposures in Uranium operations may result from external beta-gamma radiation emitted by Uranium and its progeny, internal exposure to alpha and beta radiation due to the inhalation and ingestion of Uranium ores, Radon gas, and Radon progeny in mine, mill, and laboratory atmospheres and from the contamination of environmental working surfaces and clothing by Uranium-bearing compounds and ore. This paper summarizes occupational experience with reference to the exploration, surface mining, underground mining, milling and transport of Uranium by one company in the U.S. and Canada.

Jan 1, 1981

There has been some confusion over the selection of discount rates when performing stochastic simulations of a project's net present value (NPV) using risk- adjusted discounting techniques. Some argue that lower discount rates should be used when performing stochastic valuation simulations. This creates higher NPV values and improves the attractiveness of a project. Others argue that the discount rate should not be lowered for these simulations. This paper exposes the source of this confusion. It demonstrates that stochastic simulations do not remove the risk inherent in a project and, therefore-do not improve a project's value to the risk-averse investor. Risk-adjusted discount rates should, therefore, not be adjusted downward when performing stochastic NPV simulations. Stochastic simulations are, however, shown to he useful in several aspects of project valuation.

Jan 1, 1996

By Trent A. Tempel

In 1989 Newmont Gold company initiated a project to develop a treatment process for higher grade refractory gold ores to be mined from deposits along the Carlin Trend in Nevada. Extensive laboratory and pilot testing have identified a unique whole ore roasting process for oxidizing these ores prior to gold recovery by conventional cyanidation techniques. Subsequent detailed engineering studies by Fluor Daniel evaluated three different dry grinding flowsheets for feed preparation to this roasting circuit. The selected flowsheet will incorporate a two compartment ball mill with an attached drying chamber that is driven by a 11.2 MW (15,000 hp) wrap-around motor.

Jan 1, 1993

By E. J. Donovan, O&apos

The use of Dynamic Analysis techniques in the design of conveyor systems is extremely limited. The most frequent use of the technique is in large and expensive systems where the emphasis is on insurance against failure caused by catastrophic tension waves. This paper sets out to illustrate a much wider range of applications where dynamic analysis has been successfully employed. The examples chosen deal with identification and correction of dynamic low tension problems, the variability in take-up movement as other system parameters change, the requirement for proper tuning of starting controls and finally the absolute necessity for a complete understanding of the entire system when specifying brakes for critical applications. The intent of the paper is to get designers to view a conveyor as a system of interacting flexible components rather than as a single rigid body.

Jan 1, 1993

By K. A. Natarajan, Abha Kumari

In this paper, electroleaching and electrobioleaching of ocean manganese nodules are discussed along with the role of galvanic interactions in bioleaching. Polarization studies using a manganese nodule slurry electrode system indicated that the maximum dissolution of iron and manganese due to electrochemical reduction occurred at negative DC potentials of -600 and -1,400 mV(SCE). Electroleaching and electrobioleaching of ocean manganese nodules in the presence of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans at the above negative applied DC potentials resulted insignificant dissolution of copper, nickel and cobalt in IMH2S04 and in sulfuric acid solution at pH 0.5 and 2.0. Mechanisms involved in electrobioleaching of ocean manganese nodules are discussed. Galvanic leaching of ocean manganese nodules in the presence of externally added pyrite and pyrolusite for enhancement of dissolution was also studied. Various electrochemical and biochemical parameters were optimized, and the electroleaching and galvanic processes thus developed are shown to yield almost complete dissolution of all metal values. This electrobioleaching process developed in the laboratory may be cost effective, energy efficient and environmentally friendly. Keywords: Ocean manganese nodules, Electroleaching, Electrobioleaching, Galvanic interactions

Jan 1, 2003

By J. H. Rowland

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on the effectiveness to extinguish conveyor belt fires. The four different types of suppression systems were water sprinkler, deluge type water spray, and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 72-in-wide fire resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 500-550 feet per minute (fpm) and 1350-1500 fpm. Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to extinguish any smoldering belting was greater than the current MSHA regulations require. MSHA regulations only require 10 minutes of water supply to the suppression system. In the test set up neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 500 fpm air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test set-up, arrangement of the fire suppression systems, and conclusions regarding the effect of air velocity on fire suppression system design and performance. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By W. W. Simpson, S. A. N. Sheya

A procedure was developed by the U.S. Bureau of Mines for recovering gold, silver, cobalt, copper, and zinc from a massive sulfide ore by a hydro-metallurgical process. The procedure consists of (1) oxygen pressure leaching; (2) iron, arsenic, and copper removal from the leach solution by precipitation; (3) selective extraction of cobalt and zinc from solution; (4) electrodeposition of the cobalt and zinc from the strip liquor; and (5) cyanidation of the pressure leach residue to recover gold and silver. The results are discussed in terms of efficiency of metal recovery and conclusions drawn as to possible benefits and broad applications of the process.

Jan 1, 1990

By Jan Leja

Surfaces of metal sulfides react readily with selected constituents of environment. Two types of reaction products may form: (1) primary, chemisorbed and hydrophobic surface products or primary hydrophilic surface products, and (2) secondary reaction products -- produced during continued oxidation-reduction processes. For flotation, the chemisorbed surface product and the secondary reaction products, elemental sulfur or metal xanthates, must provide sufficient hydrophobicity of the surface to ensure particle-bubble attachment.

Jan 1, 1986

By Vathsala Rajagopal, lwao lwasaki

The grinding media materials for the mining industry require corrosion and abrasion resistance properties not only to minimize the wear but also to improve the flotation recoveries of sulfide minerals. The media wear mechanisms and the factors influencing the grinding ball wear during grinding are discussed with respect to abrasion, corrosion and impact wear of grinding media materials. Interactions between the grinding media and sulfide minerals in a ball mill adversely affect the floatabilities of the ground minerals. The possible galvanic interactions between grinding medium-mineral and their effects on the flotation responses of sulfides are also reviewed. The selection criteria for alloy composition that reduces the overall wear along with adverse effects on flotation are brought out.

Jan 1, 1992

By Christoph Wels, Michael Royle, Shannon Shaw

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2000

By Steven W. Hunt, Steven B. Fradkin, Roger J. Maurer

During the 1980s and 1990s, twenty deep shafts were constructed in Milwaukee to depths from 85 to 91 m (280 to 300 feet) through soil and weak rock thicknesses ranging from 37 to 69 m (122 to 227 ft). Adjacent compressible soils, settlement sensitive structures and high groundwater levels required that shafts be constructed without dewatering. Contractors attempted several methods of ground support and groundwater cutoff. Significant problems developed during construction of 11 of the 20shafts. One shaft collapsed; groundwater blow-ins occurred at five of the shafts; and seepage caused unfrozen windows at three of the freezewalls. Ultimately, combinations of grouting and ground freezing were utilized to complete all of the shafts into bedrock. This paper discusses the main design and construction challenges experienced and the lessons learned.

Jan 1, 2003

By W.A. van der Westhuizen

Mineral resource management has become a well used phrase in the mining and minerals industry. Mineral resource managers are being appointed in many mining and mining-related organisations. Every mineral resource manager has his/her own ideas regarding what MRM means. There seems to be a tendency to define MRM close to home; geology would apply MRM principles to their environment and so will metallurgy, planning, mining, survey and every discipline and participant in the mining value chain. What do we do in the MRM environment and what do we aim to achieve? Surely we must have goals: what are they? Is value tracking MRM? What about best practices? Let us start at the beginning: what do we want to achieve in any mining operation? The minerals industry would like to make money, now and in the future. This calls for serious management inputs. The most important aspect is a holistic management approach regarding the total mining value chain. Process optimisation follows with application of Mineral Resource Throughput Management (MRTM) and Process Flow Management principles. Once flow processes have been established the necessary condition driven standards and measurements will be installed to ensure continuity in applicable processes.

Jan 1, 2012

By J. Brent Hiskey, Srini Raghavan

The physical chemistry of dissolution of silicate and complex oxide ores in aqueous lixiviants has been reviewed. Particular attention has been paid to the analysis of dissolution mechanisms and kinetic models and to the elucidation of the role of the porous nature of the materials on dissolution behavior. Importance of the physico-chemical characteristics of the leach residues on leaching efficiency has been discussed.

Jan 1, 1989

By Dennis Greene

Real-time GPS position monitoring of mining equipment is becoming more and more commonplace. Digital mining plans can now be used onboard properly equipped earthmoving equipment and excavation status is available in real-time via high bandwidth data radio systems. These systems provide a closely integrated link between operations and planning. No longer must operations wait for or be hindered by insufficient survey marks, nor is engineering delayed by lack of timely mine status information. Unprecedented efficiency gains become feasible -from the engineering office, to drilling and mucking, to reclamation, as well as in mine construction projects. Direct economic benefits of these systems will be explored as will the less tangible, but very significant, indirect operational efficiency gains.

Jan 1, 1998

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

 The paper demonstrates that Belle Fourche Shale (BFS), an abundant shale, can be transformed into a ceramic through careful characterization and thermal processing. The study explores the potential of BFS ceramics for use as refractories and thermal energy-storage devices, highlighting their high thermal storage capacity, good thermal shock resistance, and cost-effectiveness.

Dec 1, 2023