Search Documents

By Peter Zhang, Daniel Su, Bo Kim, Berk Tulu

This paper summarizes significant findings from the ongoing NIOSH Gas Well Stability research over the past decade; in particular, the important ground control engineering considerations. Longwall-induced surface and subsurface deformations may induce gas well casing deformations and stresses, depending on a few parameters such as overburden depth, overburden geology, topographic relief, strata dip, gas well setback distance, and a gas well casing cementing alternative. Overburden depth to the mining seam is one of the most influential factors; shallow overburden depth induces large horizontal displacement and resulting casing deformation and stress, while deep overburden depth induces large longwall-induced vertical pressure. Overburden geology is another important factor affecting the longwall- induced casing deformations and stresses; the large contrast of bending stiffness at the soft-to-hard rock interfaces tends to induce large casing deformations and stresses. Large surface topographic relief and the presence of soft-to-hard rock interfaces below the stream valley bottoms may shift longwall-induced subsurface gas well casing deformations closer to the surface, thus having less impact on underground. mining operations. Strata dip magnifies longwall-induced deformations by 20% per degree of strata dip for down dip longwall excavations. The gas well setback distance is also a critical geometric parameter; the effect of longwall-induced deformation decreases exponentially as the setback distance increases. Longwall-induced casing deformation and stress will be mitigated or totally uncoupled for uncemented production casing.

Jun 25, 2024

By A. Kalmes, B. Dehler, D. Kopp

Nutrien has six potash mines in Saskatchewan and has been proactive in maintaining the integrity of their tailings facilities through ongoing assessment, design, operation, inspection, and monitoring. Nutrien commissioned a system inventory and semi-quantitative risk analysis (SQRA) of all dikes to further environmental stewardship at their potash facilities. The inventory assessed nearly 100 dikes; each dike was rated according to a probability and consequence factor and assigned a risk score. The risk scores were used to develop a risk matrix for each of the six sites and risk-response actions for each dike and segment. The inventories and SQRAs will help each site assess priorities for investigation and risk mitigation, if necessary. The study results will also help Nutrien refine corporate wide tailings governance standards and demonstrate compliance with various governance regulatory obligations.

Mar 2, 2022

By Barada K. Mishra

The potential merit of the discrete element method (DEM) as a numerical tool for analyzing process engineering problems involving particulate material is discussed. In this method, the dynamic equilibrium equations for each distinct and deformable body are solved. Therefore, it readily lends itself to modeling large numbers of discrete, interacting bodies as in mineral processing operations where a charge of particulate material is processed. Here some applications of DEM are reported: motion of particles in the ball mill, mixer, and jig. Although DEM has made very little headway in mineral processing research, it is shown here that a host of other areas of industrial interest in the context of flow of particulate materials can also be made amenable to analysis by this method.

Jan 1, 1993

By Liang Ruilu, Guo Lihua

In light of the properties on process mineralogy of the old tailings in a certain copper mine in the People's Republic of China, a new process of combined reagent and stepwise flotation is applied in which the flotation of copper sulfides is followed by the flotation of copper oxides. Recoveries of copper and associated gold and silver have been greatly increased. The tailings obtained were subjected to the gravitational separation-magnetic separation process to recover iron minerals. Tailings from iron separation are taken as fillers and sent to the pit underground. Thus, the secondary resources are comprehensively utilized.

Jan 1, 1995

By Stephen G. Gemell

Gold mining has undergone a massive revival in Australia within the past decade. With very few exceptions, these operations are involved with the development of deposits which have been previously and partially worked by underground methods. In most cases, current operations have involved the open cut mining of near-surface remnants or low-grade hanging wall and footwall mineralisation. A growing number of mines are, however, progressing to the development of underground workings either as extensions of existing open cuts or as "stand alone" projects. These operations vary in scale from the Kalgoorlie operations of North Kalgurli Mines Limited and Kalgoorlie Mining Associates to the small scale "gouging" operations of individuals and partnerships. The individual production rates rarely exceed 200 000 tonnes per year, primarily because of the magnitude of reserves or the style of access available for rehabilitation. The narrow-vein mines were initially re-opened using the traditional methods, in particular shrinkage stoping and cut-and-fill stoping. As a result of experience gained in various ground conditions, certain variants have become popular. This paper investigates the fate of the traditional methods in Australian practice, and reviews some of the recently applied variants. This involves not only a perusal of current practices, but also an assessment of the influence of recent technological development on the economics of narrow-vein mining. Some consideration is also given to the effects of previously employed stoping techniques on efforts to access remnant blocks in the re-development of old mines.

Jan 1, 1989

By J. Peck, M. J. Scoble, C. Hendricks

This paper is based on field studies in North American surface mines. The work involved the adaptation of microprocessor-based instrumentation to monitor various operating parameters on-board rotary blasthole drills and mining shovels. Following a review of instrumentation and monitoring methodology - drawing on experience gained under field conditions-the paper will focus on the application of monitoring technology within the framework of an Integrated Equipment Monitoring System. Such a system will permit real-time performance evaluation of key equipment involved in surface mine production. Drill performance monitoring has been demonstrated through work to date, to provide significant input into blast design, reserve estimation, mine planning and production control processes, through an improved facility for ground characterization. Monitoring excavation equipment has been proven valuable in assessing how effectively the input from drill monitored data has been used in the evolution of blast designs. This specifically refers to assessing blast efficiency through measuring associated levels of excavator performance in relation to muckpile characteristics. The medium-term goal of equipment instrumentation and monitoring has been to assist mines in optimizing the overall rock breakage and handling process. Based on the reported results, this has been accomplished. Long-term efforts now concern using a greater understanding of equipment performance and response to varying operating conditions as a foundation for the implementation of mining automation.

Jan 1, 1993

By W. Robert Rose, Randall Pyper, Carlos Mirabal, Jaime Eguivar

In 1984, work was started to determine the viability of heap leaching silver-containing waste dumps from Cerro Rico near Potosi - Bolivia, at an elevation of 4300 meters (14 100 it.). The result today is an unusual heap leach utilizing fine crushing, grinding, and agglomeration to process 1000 tonnes per day of ore containing 200 g/tonne silver. The unique metallurgical, economic, and political factors will be discussed which led to the decision to build a heap leach rather than a conventional agitation leach plant. Capital and operating costs will be given along with some of the uncommon process design and equipment problems encountered while developing the operation.

Jan 1, 1990

By John R. Marks

In April 1990, the Homestake Gold Mine embarked on a five year, $US 23 million underground drifting and drilling program to explore promising ore targets north of the current mine. This paper describes the ventilation and air-conditioning system that was installed for the 4m x 4m x 5.2 km (ultimately) drift, which is being driven at about 8m per day in 48OC (118.5 F) crystalline rock. Design parameters are described first. Differences in South African, Canadian and U.S. drift ventilation and civil tunneling techniques proved interesting. Details are then given on equipment selection, installation and performance. Costs are included. Special note is made of safety considerations for a long, dead-end drift.

Jan 1, 1991

By R. L. Unger

Restricted fields of vision are a common problem with underground mining equipment. Also, when lighting systems are provided, they may be positioned where they cause glare. This restricts the visibility around the machines even further. To help address these problems, the US Bureau of Mines has developed a PC-based software package to aid in the analysis of certain human engineering aspects of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines.

Jan 1, 1995

By R. L. Grayson, M. P. Miano, S. Yuan

Matching the productivity gains of continuous mining machines with the increasing performance levels achieved by longwall units has required creative thinking to assure that development is completed in time for uninterrupted longwall production. By using management information systems to coordinate support operations, the most productive planning decisions can be made. This paper focuses on the role of computer technology tools in achieving improved productivity from both longwall and continuous miner sections. The primary emphasis is on the planning process and the methodology developed to guarantee the best allocation of management and manpower resources.

Jan 1, 1995

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44% to 65% depending on bench height. The field tests were performed at an Eastern, contour, coal stripping operation. Results from five experimental casting shots, using a shovel and trucks, are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35% to 65%, with an average of 50%. Fragmentation was improved, and it was demonstrated that this procedure is economically attractive, with a resultant cost savings of $0.59/m3 or $5.93/t of clean coal.

Jan 1, 1988

By M. D. Attfield

During 1992 a number of papers were published on aspects of respiratory disease in US underground coal miners. These included reports on trends in prevalence of coal workers' pneumoconiosis, the risks of developing coal workers' pneumoconiosis in relation to dust exposure, and the relationship between lung disease other than pneumoconiosis and dust exposure. The intent of this paper is to provide a summary of the essential findings from these investigations. PREVALENCE AND INCIDENCE OF COAL WORKERS' PNEUMOCONIOSIS Coal workers' pneumoconiosis (CWP) is usually detected in living miners through use of the chest x-ray. Deposits of dust in the lung, and the fibrotic tissue reactions to the dust, are manifested on the x-ray as small and large opacities. These abnormalities are quantified into degrees of severity using a standardized classification scheme (the International Classification of Radiographs of the Pneumoconioses of the International Labour Office). For small opacities, the scheme provides for a four-point scale of abnormality (0, 1, 2, 3), reflecting increasing profusion of the opacities on the x-ray. In this report, category 1 or greater small rounded opacities (CWP 1+) represents the earlier radiographic stages of pneumoconiosis. Large opacities, indicate the later and often disabling stage of pneumoconiosis, usually referred to as progressive massive fibrosis (PMF). Information collected in a national surveillance program for underground coal miners (the Coalworkers' X-ray Surveillance Program (CWXSP)) and a large epidemiologic study (National Study of Coalworkers' Pneumoconiosis (NSCWP)) provide a means to assess trends in CWP prevalence over the years following the reduction in dust levels mandated by the 1969 Federal Coal Mine Health and Safety Act (FCMHSA). These programs are operated by the National Institute for Occupational Safety and Health (NIOSH), and are described in detail in Attfield and Althouse (1992) and Attfield and Castellan (1992). Both studies were divided administratively into distinct time periods, and the results shown here reflect that division. Figure 1 shows the prevalence of CWP 1+ as determined from data from the CWXSP, plotted by time period and years in mining. There is evidence of a temporal reduction in prevalence. (The lack of an obvious decline in the early 1970s may be an artifact arising from use of different versions of the standard classification.) Figure 2 provides information in the same format for PMF, and shows a similar trend [ ]

Jan 1, 1993

By W. W. Roepke, B. D. Hanson

A major problem facing the coal mining industry today is the need to meet more stringent dust standards due to quartz. When secondary suppress ion is not adequate, the time-consuming and costly cut-and-try method of modifying the mining machine is used in the hope that it will reduce dust generation. The Coal Cutting Technology Group, at the Bureau of Mines' Twin Cities Research Center, has developed an inter-active computer program for drum- type cutting systems to help identify, in advance, modifications that offer the best potential for reducing dust. The program, Relative Dustiness Indicator (REDI), evaluates machine dimensions, seam characteristics, and operator-controllable variables for dust generaton, energy, forces, and product ion.

Jan 1, 1986

By E. Suoninen, K. Laajalehto, L. Kartio

Efficient separation of pyrite from other sulfides is of great importance for the metallurgical performance of flotation processes. In this work Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Photoelectron Spectroscopy (XPS) were used to study the surface chemistry of pyrite in depression, activation and xanthate adsorption under conditions of controlled potential. Modifications of pyrite surfaces after treatment with depressants (lime, sulfur dioxide, sodium cyanide) and after activation with metal ions (Cu, Pb) were studied. The principal adsorption product identified on pyrite was dixanthogen whose formation started at about +0.15 V and +0.25 V (vs, SHE) in ethyl and amyl xanthate solutions, respectively. Copper xanthate was formed on copper(II) activated pyrite. Activation mechanism of pyrite by copper(II) salts is likely to be electrochemical where copper occurs as copper(I) on the surface of pyrite. Effective depression is achieved by sulfur dioxide and sodium cyanide. Depression at high pH is due to formation of iron(III) hydroxides. Calcium ions do not affect the electrochemistry but adsorb on pyrite and reduce the surface sites for dixanthogen adsorption.

Jan 1, 1995

By Ruth A. Maurer, Steven L. Capt. Van Drew

Coal preparation for a company having several sources of coal and several contracts for sale of coal was modeled. The objective was to minimize wash loss by selecting the quantity of coal to be supplied from each source and the appropriate washbox specific gravity setting to yield contract quality for a given shipment. constraints inposed by silo and stockpile sizes, plant and rehandling capacities, and varying coal quality specifications were included in the model. Solution is by iterative linear programming on an Apple II.

Jan 1, 1987

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By J. E. Taylor

A detailed planning and design project has been undertaken at Callide Coalfields, as the first step towards implementing a fully integrated mine graphics system. The system, when fully installed, will support applications ranging from business graphics through to terrain modelling and computer-aided design. The conceptual design which will accomplish this is presented. The problems of retrospectively applying graphics standards to existing applications are discussed, and a practical solution outlined.

Jan 1, 1986

By R. J. Sweigard, M. Rohatgi

Differential settlement on reclaimed land presents a particular problem when the land is to be used for row crops. The poorly drained depressions caused by differential settlement restrict crop yield, resulting in additional costs to alleviate the problem. Potentially more serious is the threat of failing to meet target yields due to settlement-related reductions. Because the mechanism by which the problem occurs is not well understood, a physical model study was conducted to investigate the importance of several factors. The importance was considered of such factors as the relative amounts of rock and unconsolidated overburden in the undisturbed condition and the size distribution of rock fragments. But the analysis concentrated on the causes of settlement in the reconstructed soil layer above the rock spoil.

Jan 1, 1991

By Roy Eric Lurie

Computer based signal processing techniques for obtaining empirical dynamic models from measured mill circuit data are discussed. This modelling is the first step towards designing a particle size control strategy. Experimental data from a computerized acquisition sys tern is examined and analysed, and a number of model identification procedures are applied. The resulting models are compared and a suitable model is selected, illustrating the benefits of computer tools for control system design.

Jan 1, 1992

By K. V. S. Sastry, A. J. Hunt, K. D. Lofftus

Sol-gel processing is rapidly becoming an important process for producing such advanced materials as high activity catalysts, fiber optics and ceramic precursors. These materials can be tailor made with properties unique to sol particles as well as the gel aggregates by controlling production of the sol, the formation of the gel, and the removal of the interstitial fluids. This paper presents colloidal and kinetic principles of sol generation and gel formation. Hydrolysis of alkoxides provides the best means of controlling sol production and electrostatic stabilization enables the formation of the most homogeneous gels. Gelation occurs by hierarchial aggregation which produces inhomogeneities much larger than the sol particles. Colloidal and kinetic principles can be applied to reduce the size of the inhomogeneities and obtain high performance transparent insulation and new ceramic composites.

Jan 1, 1990