Search Documents

By W. R. Dearman, N. Turk

The theoretical relations between the strain and stress Mohr circles make it possible to establish a relation between the internal friction angle [ ] and the Poisson's ratio (v) of rocks. The internal friction angle is related to the Poisson's ratio as Sin [-] = (1 - v)/(l + v). This relation gives lower friction angle values than the triaxial Mohr envelopes and higher values than those given by surface sliding friction tests.

Jan 1, 1986

By Frank S. Hicks, Y. Charles Guan, Glenn A. Gruber

This paper describes a two-part program funded by the Florida Institute of Phosphate Research and performed by Jacobs. The first part of the program was to examine the application of ultrasonic treatment to clean phosphate particle surfaces. Florida phosphate pebble and rougher flotation feeds were treated in an ultrasonic trough to remove clays. Also, the de-oiling of rougher concentrates by ultrasonic treatment was tested. In order to improve the clay removal efficiency, viscosities of primary cyclone overflow from six beneficiation plants were studied in the second part of the program. Viscosities for different samples at the same clay % solids vary significantly, and increase exponentially with clay % solids content for the same sample. A method of controlling cyclone operation using on-line viscosity measurements and pump box level sensors is proposed to logically improve primary cyclone performance.

Jan 1, 2002

By Jim M. Johnson

INTRODUCTION The facility water balance and maintenance of sufficient excess storage volume in the solution control system are often amongst the most critical facets of design and operation of heap leach facilities in cold, snowy climates. The purpose of this paper is to summarize and discuss climatic and operational factors which have a significant impact on heap leach water balance evaluations in high snowfall climates. Example water balance simulations are presented for proposed heap leach projects located in areas subject to high snowfall in the northwestern United States. The climatic data input to these simulations represent both net evaporative and net precipitation climates. FACTORS AFFECTING WATER BALANCE EVALUATIONS The combined effects of seasonal operations, re1atively low evaporative losses, and potentially large inflows to the solution control system from snowpack and spring storms require an enhanced awareness of the factors which impact facility water balance. Unlike operations at mines in more arid climates, seasonal excess water rather than a shortage of make-up water is the rule. A thorough understanding of a number of factors, including regulatory constraints, climatic influences, and impact of operating philosophy and techniques, is critical to successful development of an incident-free heap leach operation under high snowfall climatic conditions. A process water circuit schematic for a typical heap leach operation is shown on Figure 1.

Jan 1, 1988

By Jozef Szymanski, Julian Partyka, Jerzy Krynicki

In order to study blast-induced dust in a hard rock metal mine experimentally and analytically, a part of a stope mined by Vertical Retreat Mining (VRM) was monitored throughout its lifetime. Dust measurements were used to describe the dust source, to study the dynamics of removal of airborne dust from the blasting area, and to examine a variation in dust production with a stope's progress. An analysis based on graphical and analytical comparisons of blasts taking place in a single stope is presented and discussed. Also, some transient phenomena of dust flow in the stope vicinity, caused by the blasts only, are examined.

Jan 1, 1997

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By F. G. Boehm, T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force, Pv, a lateral force, Ph, and a longitudinal force, Pl. A method for estimating these forces is proposed that relates each of their values to the properties of the conveyor structure and rails, the shifting operation parameters, and other site-specific conditions. The effect of this force on the shifter behavior is analyzed, and guidelines are developed for selecting a suitable shifter. As well, other equipment requirements for the shifting operation are discussed.

Jan 1, 1988

By B. K. Mishra, Partha Chakroborty

Jigs are the most important equipment used in the separation process that exploits the stratification of particulate matter under the influence of hydrodynamic and gravitational forces. Very little is known about the determined mechanisms by which particles of varying density, size, and shape stratify in a moving bed. A model is developed by using the discrete element method to understand the behavior of jig bed. This model is utilized here to study the stratification behavior of the bed and its control. The control action is based on the understanding of the physics of the stratification process within the framework of fuzzy logic. The actions suggested by the fuzzy logic controller (FLC) depend on the current degree of stratification and the existing frequency of the jig cycle. The results show that the FLC achieves efficiency in stratification with minor variations to the jig cycle.

Jan 1, 1995

By F. H. Mertens

The concentrators of Gecamines are fed by a great variety of ores and produce different types of oxide and sulfide concentrates. It is therefore important to translate the performances of each circuit in terns of dollars in order to reach cost optimization in each mine to product line. A new system has been recently implemented for achieving this objective. Technical data and expenses are collected, allocated and analysed on mainframe applications. On the other hand, optimization and simulations are carried out on microcomputers which are linked with the mainframe files. Various kinds of auditing reports can be produced, including those leading to investments and cash-flow pattern which are

Jan 1, 1991

By D. Butler

Subsurface density changes can be detected by very precise surface gravity measurements. A feasibility study, combined with field experience using modern instruments, will indicate the probability of success. In addition to projected anomaly parameters, surface conditions that effect the survey precision must be evaluated. Examples with excavated zones at 9 m (30 ft) of depth and [+] 22 microgal error are compared to the same model at 30 m (98 ft) of depth. The figures illustrate anomaly detectability. The survey error is a function of surface topography and lateral density variation in the very near surface.

Jan 1, 1990

By D. G. Millette, A. J. S. (Sam) Spearing

The design of a cost effective backfill system involves many aspects and various inputs from different engineering disciplines. Backfilling is a very significant mining cost and efforts need to be made in the design stage to maximise efficiency and flexibility whilst minimising costs. The aspects that need to be considered include the following: Required fill performance underground Peak and average fill tonnage requirements Backfill scheduling in the mining cycle Material selection, testing and preliminary costing Plant design and storage needs Infrastructure requirements Implications on surface waste/tailings disposal and costs Total backfill costs In order to produce a cost effective and efficient backfill operation, a multi-disciplinary project team is required that should include the following skills and functions: Mine Planning Rock Engineering Metallurgy Mechanical Engineering Environmental Health and Safety Tailings Disposal/Waste Management This paper discusses the above and indicates important aspects that should be considered.

Jan 1, 2001

By S. Behl, Pradip

Selective-flocculation process development generally involves single-mineral flocculation tests to identify the appropriate polymer experimental conditions for achieving the desired selectivity. Invariably the selectivity predicted on the basis of such tests is not realized when mixed-mineral tests are conducted. A systematic experimental investigation revealed that adsorption of the polymer on various substrates is critical to selecting the suitable flocculant. Simultaneously, a mathematical model was developed to predict the overall process of efficiency with a given polymer. In this paper, the results of these efforts to scientifically design a suitable selective flocculation process are presented.

Jan 1, 1994

By Brenda J. Morrison

Anything to do with radioactive waste disposal in these days is regarded in a very negative light and with the thought that no possible good could come of anything connected with it. However, it should be remembered that the Austrian government's disposal of some tailings from the Joachimsthal mines resulted in what was probably the most important scientific discovery of this century. In 1898 the Austrian government agreed to give a Polish research assistant working at the School of Physics in Paris one ton of tailings to enable her to carry on her research. Her meagre stipend and the lack of a research grant did not allow her to purchase the ore which was relatively expensive. The uranium oxide in it being used to colour the famous Czechoslovakian glassware. As we all know, from this ton of ore Marie Curie by her own physical labours extracted one gram of radium. When she started this research she was pregnant with her first child. Nothing of course was known at the time about the biological effects of radiation. Very shortly, of course, the acute effects such as skin burns were observed but it was some years before the chronic effects were noted. It is impossible to estimate to what cumulative amount of radiation that Marie, Pierre and their daughter Irene were exposed but it must have been enormous and it took its toll. Marie complained for many years of fatigue and exhaustion and at one point she was seriously ill with some kidney problem which was probably due to toxic effects of ingestion of uranium. She lived until she was 67, however, and died of leukemia. Her eldest child, Irene, who carried on her work, did not live as long; she died of leukemia at 57. The other daughter, Eve, related how her mother and she went on a skiing holiday not many years before her death, and how her mother at this time would swim 300 meters at a stretch. (Curie, 1937). This suppleness of limb could have been due to the anti-inflammatory action of radiation. Even today, patients in France with certain types of rheumatic conditions are treated with injections of radium, where other anti-inflammatory drugs such as aspirin or cortisone have not worked. (Bertrand, Legras and Martin). All this anecdotal information is just to point out that it is an ill wind that blows no good. The risks connected with uranium waste disposal and tailings piles are

Jan 1, 1980

By W. S. Urbanski, A. L. Devernoe, M. S. Walker

Theory and practice are described for a new processing method capable of precise mineral separations based primarily on differences in particle specific gravities at specific gravity split points from 1.5 to 21.0 and beyond. Separations are analogous to those achieved using rotating heavy media, except that the effective specific gravity of the fluid is created magnetically using a relatively dilute, low-viscosity, water-based magnetic fluid. Results reported here for a large, laboratory flow-through separator include: 1) 99% grade with 97% recovery in single pass separation of a suite of heavy minerals from quartz at I0 kg/h, 14 tph/rm2 of duct cross section, 2) 90% grade and recovery in single-pass separation of mixtures of sand-size, non-magnetic rutile (4.23 specific gravity) and zircon (4.72 specific gravity) at throughputs of 35 kg/h, 47 tph/rm2 of duct cross section, 3) partition curves having Ep90-10 transition widths 5% or less of mineral specific gravities, and 4) essential confirmation of the theory.

Jan 1, 1991

By D. R. Spears, D. A. Stanley

The US Bureau of Mines investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed and solids concentration on the kinetics of shear-flocculation. The results showed that shear flocculation is a two-stage process. In the first stage, which occurs during the first 1-2 min. of the reaction, the mean particle size increases rapidly, and in the second stage, an equilibrium is set up between the rates of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear flocculation, which was dependent on solids concentration and collector dosage. This stirring speed was the minimum necessary for particles to overcome the electrostatic energy barrier, and that results in keeping the conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1995

By Q. Lin, D. Z. Wang

Molecular design plays an important role in development of new flotation reagents. Group electronegativity calculation is a main method of molecular design. It is commonly used in calculating the hydrophilic-hydrophobic balance of reagents, particularly in designing chain length of flotation reagents for located minerals. But there is a limit to group electronegativity method. The method can only apply to those of [Ø]known straight-chain compounds ([Ø] is the hydrophobic energy of each -CH2- , determined by experiment). In this Paper, we propose another new calculation method: fragment method of flotation reagent. The method could be used as a supplement of group electronegativity method to design and calculate flotation reagents without any limitation. With the fragment method, we can calculate the hydrophilic-hydrophobic performance of any known or unknown reagents including those complicate structure compounds such as cyclic, branch, heterocyclic and so on by summing the appropriate structural elements (fragment). The principle, calculation stages and some results of designing new-type flotation reagents by fragment method are presented in this paper.

Jan 1, 1995

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By S. S. Churchill

Introduction Amidst the apparent chaos of the final push to complete a major construction project, a small group of specialists works with great intensity. Armed with yellow "in test" and green "turned over to operations" tags, these startup engineers follow detailed preoperational test procedures to confirm that a plant is ready to operate. They follow a test schedule designed to complete individual process system in the order they will be needed by operations. After extensive preliminary testing, the startup engineers begin the truly exciting part of their work - initial operations. The thrill of engaging the clutch for the first time on a 10,000 horsepower grinding mill makes all the long hours worthwhile. Preoperational testing and startup are of critical importance to the success of a project. No other aspect of a construction project allows such opportunities for success or failure, and no other aspect is so critically influenced by careful planning. At Bechtel, the tasks of preoperational testing and startup are among the responsibilities of the Mine and Plant Operations group. The Preoperational Testing Process Preoperational testing is the transition phase between constructon and startup on a new plant. It includes the preparation of detailed test schedules and procedures. The schedules are used to coordinate construction completion activities, so that systems are available for startup and operations in a rational sequence. The procedures form the basis for performing the testing and documenting its completion. Tests include instrument calibration, wire insulation tests, wire termination verification, mechanical alignments and inspections, and system cleaning and flushing. Where possible, the systems are then operated on water and their performance recorded. Normally, either the construction contractor or a team of specialists has the responsibility to perform preoperational testing. Witnesses to the testing may be owner operations and maintenance personnel, engineers from the design firm, or specialists assigned to the project who provide assistance and guidance to the contractor in addition to witnesing the work.

Jan 1, 1986

By G. T. Adel

During the past decade, researchers at Virginia Polytechnic Institute and State University have worked to develop a novel flotation process for treating very fine particles. This process, which is now commonly known as [microbubble column flotation] (MCF), has been shown to be very effective in a number of applications related to fine coal processing. These applications include the retrofit of existing preparation plant circuits and the recovery of additional coal fines from refuse streams. In addition, work conducted under the sponsorship of the United States Department of Energy indicates that the MCF process is capable of producing superclean and ultraclean coals from many eastern U.S. coals. This paper describes some of the basic problems associated with fine particle flotation and the design and operational features of the MCF process used to minimize these problems. Also presented are the results of ongoing pilot- and field-testing programs.

Jan 1, 1989

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment like haul trucks are a major safety concern in the U.S. mining industry. They account for more than 50 percent of surface mine fatalities each year [1]. A recent National Institute for Occupational Safety and Health (NIOSH) analysis of 91 fatal incidents identified loss of vehicle control and situational awareness as key contributors [2]. However, the first-hand perspectives of operators are often missing, emphasizing the need for deeper insights into operators’ decisionmaking, lessons learned, sensory cues and mental strategies used during near-miss events. The findings in this analysis will help inform the development of training and safety solutions to prevent or reduce haul truck accidents.

May 1, 2025

By R. J. Puchala, B. M. Hawrylewicz

High voltage electrical discharge in water causes instantaneous release of accumulated energy into water. The experiment described in this paper regards the utilization of the electric discharge phenomenon in rock splitting. The pressure in the shock waves created by the discharge inside a small volume of water enclosed in solid rock causes stresses which can result in breakage of rock. Holes drilled in tested samples were notched in order to weaken the tensile strength of the rock and achieve a uniformly directed split. The influence of the notches was theoretically analysed and compared with experimental data. Results of the tests have been statistically elaborated in order to correlate the newly-created surface to the energy supplied.

Jan 1, 1986