Search Documents

By J. E. Rourke, O&apos

This paper describes the use of index testing to obtain rock properties that are useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include: point load; Schmidt hammer hardness; abrasion hardness; and total hardness. The first two index properties correlate to uniaxial compressive strength (UCS) and Young's modulus. Discussions are given on empirical, normalized relationships of UCS to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The hardness property indices correlate to construction performance parameters and some relevant experience is cited. Examples of data are presented from an index testing program carried out primarily on siltstone, sandstone and limestone rock core samples retrieved from depths up to 1005 m (3300 ft) in a borehole drilled in the Paradox Basin of eastern Utah. The borehole coring was done for a nuclear waste repository site investigation.

Jan 1, 1990

By Jeffrey M. Listak, Gregory J. Chekan

The U.S. Bureau of Mines, in an effort to improve coal conservation and utilization is currently investigating longwall panel layouts to maximize coal recovery and minimize interactive problems in multiple-seam operations. When longwalling coalbeds in descending order, the transfer of stress from overlying gate roads is a major design constraint affecting pillar stability in the lower mine. The lower mine gate road pillars must be properly designed to withstand the additional load transfer if gate roads are superpositioned in successive seams. The Bureau's MULSIM/NL model was used to analyze load transfer mechanics for superpositioned gate road pillars. Analysis of Longwall Pillar Stability (ALPS), which is an empirically based design method for longwall gate road pillars, was used to calibrate model input parameters. The attributes of both the MULSIM/NL model and ALPS were combined to develop a modified method for estimating pillar stress for multiple-seam cases. The modified method uses a multiple-seam (MS) factor to estimate the stress on the lower mine gate road pillars when superpositioning is practiced. Numerical analysis shows that the MS factor is dependent upon the interburden thickness and pillar width and is presented in a series of graphs relating these two parameters. Several examples are included to illustrate the use of the MS factor for estimating lower mine pillar stress and resulting stability factors.

Jan 1, 1992

By W. D. Hall, M. Norris, J. R. Henke

Dewatering wells producing iron-rich water experience rapid declines in yield and drawdown due to the formation of ferric (Fe3+) hydroxide deposits in well screens, pump intakes and riser pipes. Precipitation is caused by a combination of dewatering-promoted iron oxidation and iron oxidizing bacteria. Physical and chemical well rehabilitation techniques, as well as alternative well-construction and well development techniques, were evaluated in this study. The addition of acid downhole feed systems to dewatering wells that are prone to iron encrustation can, in many cases, prolong their operational lives up to 500% that of unacidified wells.

Jan 1, 1992

By P. M. Brown

The Bureau of Mines, U. S. Department of the Interior, has developed a method of dewatering clay slurries based on flocculation by high-molecular-weight polymers and water removal from the formed flocs using a trommel or hydrosieve. The exchange ion on the clays affects their dewaterability. Metal ions in solution and on the exchange sites of smectite clays are known to act as Lewis acids. Recent work has determined that these ions can be titrated with high-molecular-weight polymers. The relative acidity of the exchange ion and the basicity of the polymer determined by the new method give insight into the dewatering mechanism.

Jan 1, 1988

By J. E. Powell

Introduction The disposal of mine tailings, development rock, and other unwanted refuse material underground in mines by using pneumatic conveying techniques has been undertaken in the coal industry for many years. Similar equipment has been utilized for backfilling hard rock mines and is currently being applied in a gold mine in South Africa where development rock is being stowed in the mined-out stopes to help reduce the incidence of rock outbursts. On a limited scale, pneumatic conveying has been applied for backfilling uranium mines and one particular mine in New Mexico, U.S.A., has used this technique for 8 years. Other uranium mines in this area are now considerinq the dry backfill technique to eliminate the problems associated with hydraulic fill. The need to backfill in uranium mines is primarily of importance to improve ventilation, stabilize the pillars and roof, and possibly to extract a larger percentage of the uranium ore. If this can be achieved by utilizing the tailings from the beneficiation plant and using rock from the development headings which in itself may be slightly radioactive, then a greater benefit can be derived. Backfill can be achieved with hydraulic fill methods by running slurry into the stopes and allowing the water to decant and return through the footwall development entries to sumps for pumping to the surface. However there are several disadvantages associated with this method in that water is percolating throough the mine workings; it is necessary to build bulk heads in flat lying deposits; it is difficult to fill right to the back; and the decanted water takes with it quantities of the finer sand particles which results in maintenance problems with the mine pumps. Pneumatic conveying can overcome these problems in that the voids can be completely filled with high degree of compaction, heavy bulk heads are not necessary, the development rock can be added to the pneumatic system for disposal underground so eliminating hoisting cost to the surface, and cement can be added to the wetted material. To

Jan 1, 1980

By Jr. Neudecker

Rock melting technology can provide in-situ glass liners in nuclear waste package emplacement holes to reduce permeability and increase borehole stability. Reduction of permeability would reduce the time and probability of groundwater contacting the waste packages. In-creasing the stability of the storage boreholes would enhance the retrievability of the nuclear waste packages. The rock melting hole forming technology has already been tested in volcanic tuff similar to the geology at the proposed nuclear waste repository at Yucca Mountain, Nevada.

Jan 1, 1989

By V. E. Ross

A model has been developed that describes the behavior of mineral particles and water in the cleaning zone of flotation columns. The possible detachment of particles from their sites of attachment at the bubble surfaces is related to the flux of bubble surface area with increasing distance from the interface between the collection and cleaning zones and the late at which floated particles are transported into the cleaning zone. The drainage velocities of floated and entrained particles are calculated from the drainage velocity of water and the properties of the particles. The effects of wash water and inhibited drainage in the froth are also explicitly accounted for.

Jan 1, 1988

By B. E. Dindsale, P. B. Altringer, R. H. Lien

The Bureau cf Mines, U.S. Department of the Intericr, is investigating biolcgical and chemical deccntaminaticn of cyanide- containing leachates and residues. Biolcgical cyanide cxidaticn, using bacteria isolated from a precious metals tailings pond, destroyed >85 pct of the cyanide in several prccessing solutions containing up tc 280 ppm CN. Reaction time varied from about 4.5 hr in a trickling reactor using quartz as a bacterial substrate to 2 mo in unagitated, covered flasks. Chemical techniques were used to destroy the remaining complexed cyanide down to 1 ppm. Exploratory tests were also conducted using spent ore from heap leach operations as the bacterial substrate to determine if biological cyanide oxidation could be used to destroy the residual cyanide in spent heaps.

Jan 1, 1991

By Michael Karmis, Emily A. Sarver, Ellen S. Gilliland, Leigh-Anne H. Krometis

"Public engagement is increasingly important in ensuring the success of projects related to energy development, particularly with regard to issues of environmental protection, public health, and socio-economic impacts. This is due to concurrent trends in public behavior, including a rise in public interest in these projects that is not matched by a rise in science literacy, and increasing organization and participation of the public through social media, citizen science, and grassroots initiatives. In recent years, several high-profile incidents have demonstrated that when public concern is ignored or met with a passive response from industry, it can rapidly grow into organized opposition that negatively impacts or wholly derails a project. Engaging, listening to, and educating stakeholders during early planning and development phases are therefore essential to earning credibility and trust. Moreover, maintaining two-way lines of communication throughout the lifespan of a project demonstrates social responsibility and facilitates cooperation, acceptance, and even support from communities and others. Positive experiences with specific projects at a local, community level can influence the larger public opinion of an entire industry sector. This paper presents cases studies of public engagement related to shale gas development (including hydraulic fracturing and pipeline construction), mountaintop removal mining, and management of mixed-use watersheds near surface mining operations. The experiences highlighted in these case studies are used to draw best practices of public engagement for sustainable energy development.Introduction Within the scientific research community, the importance of public engagement has gained increasing recognition. In a 2007 article in Nature, medical researcher, Patrick Taylor, stated that public engagement has both “gone viral” and “gone global” and has the ability to make real impacts to research (Taylor 2007). Nancy Baron, the science outreach director for COMPASS, an organization providing communications training for scientists, provides further evidence for the increasing focus on engagement, including shifting attitudes observed during her own experience as a communications coach and documented in surveys, the recent inclusion of communication and engagement activities in academic tenure review, and the surge of workshops, materials, and other resources available on the subject (Baron 2016). In addition to COMPASS, a number of organizations and institutes have been developed to train scientists for communication and engagement with the public, perhaps most notably the Alan Alda Center for Communicating Science at Stony Brook University, and academic fellowship programs, such as the Leopold Leadership Program at Stanford University and the Wilburforce Fellowship Program, have been established for the same purpose."

Jan 1, 2017

By R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1997

By D. K. Sitler

Continuing advancements in manufactured diamond materials as used in rock cutting tools have created a new generation of high production tools for mining. This paper reviews the three major manufactured diamond product types available in the mining industry as supplied by General Electric Co., Specialty Materials Dept., and examines the ways these materials are used. As an integral part of this examination, the economic impact of manufactured diamond tools is evaluuted. Time and again, one will find that the premium price for these tools is economically justified when compared to traditional tools.

Jan 1, 1988

By I. J. Jansen, C. L. Hooks

Successful soil construction involves prepa¬ration of an adequate base, selection of high quality soil ma¬terials, and placement of those materials by means which will establish a continuous macropore network and modest to low soil strength. Where such has been accomplished, experi¬ments reveal row crop productivity on reclaimed land which is very competitive with that on undisturbed land. Inferior productivity and sensitivity to drought stress are experienced where the soils are excessively compacted during construc¬tion. Some deep tillage practices have been quite successful in improving the compacted soils, but it is preferable to avoid compaction as the soil materials are handled.

Jan 1, 1987

By M. G. Skowroski, G. G. Eichholz, J. P. Ambrose

Introduction It has long been known that there are extensive deposits of phosphate-bearing deposits in the Coastal Plain of Georgia in many locations that are similar to those being mined commercially in central Florida. A major drilling program was conducted in 1966-67 by the Georgia Geological Survey (GGS). The economic potential of some of the material uncovered was evaluated at that time by a team at Georgia Institute of Technology led by Dr. J.E. Husted. There were some promising results. Since then, there has been little commercial interest in pursuing this matter, though the potential for development remains. In the long term, Georgia's phosphorite deposits could be a major source of income to the state if they were commercially processed. Phosphorite deposits contain significant levels of uranium and thorium. Uranium concentrations in Florida phosphate aggregates have been found to be 120 to 140 ppm. The presence of high concentrations of uranium means that there is a small but finite concentration of radium, which subsequently leads to radon gas emanation. It is the radon emanation and its progeny that may pose the largest health problem in many types of mining. Surface mining operations can possibly elevate the radon and radon daughter concentration in the vicinity. There is always some public concern whether any increase in the radon concentration in the atmosphere by mining (surface mining in the phosphorite case) could elevate the risk of cancer in the nearby population. At the present time, a great deal of attention has been devoted to the possible health effects of radon and its decay products in the inhaled air in mines and inside buildings built on mill tailings or uranium-bearing rock (Gesell and Lowder, 1980). Several evaluations have been published on the potential health effects of the Florida phosphate operations (Guimond and Windham, 1975; Roessler et al., 1980; Travis et al., 1979) and for buildings incorporating phosphate slag aggregates (Kahn, Eichholz, and Clarke, 1983; Roessler, Roessler, and Bolch, 1983). They all indicate that such potential effects are small, but tangible, compared with other radiation effects, for instance in the nuclear industry (Cohen, 1981). In view of the current concern, especially by the US Environmental Protection Agency (EPA), with the radiological consequences of large-scale mining of uranium-bearing phosphate rock (Guimond and Windham, 1975), it was decided to assess the potential radiological consequences if the Georgia deposits were developed. This paper presents an attempt to estimate the magnitude of any radon-based health effects that might arise from future mining operations in selected areas of the Georgia coastal region. To do this, a calculational model was developed that took into account the mining operations themselves, the atmospheric dispersion of the radon released, and the radon daughter concentrations in nearby towns. The model was applied to both extremes. The first application was a hypothetical mining operation in Echols County. Echols County is very sparsely populated and, unless living very close to the site, a person would probably experience little radiation exposure, if any. The model tries to prove this point. The second application was at a site near Savannah, Georgia. Both sites contain economically feasible phosphorite deposits and were not entirely hypothetical in that sense. Site selection In the course of the South Georgia Minerals Program (Furcron, 1967), an extensive series of drill core samples had been collected from various mineral occurrences in the coastal plain. It was found that the cores from the previous drilling program (Furcron, 1967), though carefully preserved, were not readily accessible. But the GGS reports did contain gamma logs of all the holes surveyed. With the cooperation of Dr. Neal Shapiro of the Survey, some core samples were selected and assayed, and used to calibrate the gamma log data. Samples from locations known to have detectable radioactivity were screened and counted. Their measured uranium content was used to calibrate the gamma log profiles for those same holes as obtained by the GGS. On this basis, two of the higher-level sites were selected and the calibration was used to obtain integrated uranium concentrations over the length of the borehole. It is customary to describe radon and radon-daughter concentrations in "working levels" (WL), where one WL represents a concentration of radon daughters capable of releasing 130 000 MeV of alpha particles, equivalent to 100 pCi of radon in equilibrium with its daughters per liter of air. A representative concentration is 0.15 WL, below which radon levels are widely considered to be negligible. For the mine sites selected, the surface area and rock volume were determined to estimate their radon content. Working-level values were then estimated for the assumed radon release from the crushed ore and the exposed surfaces of the mine pit. According to Kisielewski (1980), 93.4% of all radon released from open-pit operations is released from the ore zone; thus, the calculations assumed that those surface areas were the main sources.

Jan 1, 1987

By V. A. Evans, D. L. Hellier

Introduction Preparing a report on fluorspar economics in the US could have been somewhat complicated at one time. This was because the number of producers, both large and small, derived production from different locations through-out the western US and the southern Illinois and western Kentucky fluorspar districts. Companies, such as Allied Chemical and Williamson Mining, operated in the Jamestown district of Colorado. In Walden and Salida, CO, the Colorado Fluorspar Co. operated mines and mills. In New Mexico, both Du Pont and Allied had mines and mills. In the Illinois-Kentucky district, US Steel, Rosiclare Lead and Fluorspar, Minerva Oil Co., and Marathon Oil all produced spar for the US market. Now all of the companies are out of the fluorspar business and, with the closing of the Seaforth Mineral Co.'s Inverness Mining Co., only Ozark-Mahoning Co. survives as a domestic producer. History Ozark-Mahoning Co., as it now exists, was formed in 1946 by the merger of Ozark Chemical Co. and Mahoning Mining Co. Ozark Chemical Co. was started in the 1920s to produce sulfuric acid for two refineries located in Tulsa, OK. Mahoning Mining was originally formed by the founders of Ozark Chemical Co. and the Youngstown Sheet and Tube Co. to produce fluorspar and associated minerals from properties in the southern Illinois and western Kentucky fluorspar district. In 1937, Mahoning Mining started an exploration program, employing contractor-operated churn drills to look for reserves in Hardin and Pope Counties in southern Illinois. Based on known reserves in the area and the results of the exploration program, work was started in the fall of 1938 to build a selective flotation plant at Rosiclare, IL. The mill was completed and put into operation in August of 1939. The company's first mining efforts were in the Cave-In-Rock district just north of Cave-In-Rock, IL. The deposits in this area were of the Manto or bedded type. They have been the mainstay of the company's operations in the Illinois-Kentucky fluorspar district. In 1950-51, the company expanded its operations by purchasing fluorspar properties from Colorado Fluorspar Co. at Walden, CO. This location was operated from 1952 through 1958 and from 1968 through 1973 when it was closed permanently. In 1974, Ozark-Mahoning Co. was purchased by Pennwalt Corp. Presently, it is a wholly-owned subsidiary of that corporation. As the only major domestic producer of fluorspar in the US today, the company's ability to survive under the flood of imported material is directly related to the four major segments of its operations. These are: exploration, mining productivity, maintenance, and marketing. All are done in-house. Exploration The Southern Illinois fluorspar district is located in the most complexly faulted area of the central US. The formations are sedimentary in nature and range in age from Devonian through Pennsylvanian. The deposits are small, they range in size from a few thousand tons up to 900 kt (1 million st), with the average minable deposit being around 544 kt (600,000 st). The ore occurs in both nearly vertical vein deposits and in Manto or flat lying bedded deposits. Due to the relatively small size of the deposits and the depth at which they occur, a good low-cost exploration program is essential to ensure that new finds of ore are equal to the mining extraction rate. Ozark maintains a leased land position in Pope and Hardin Counties that will fluctuate somewhere between a low of 40 km2 (10,000 acres) up to a high of 129 km2 (32,000 acres), depending on total size of tracts leased. Most all lands are obtained through a standard lease purchase option, with a small minimum royalty per acre during the normal 10-year option period. All leases are standard and without deviation to control land cost. All land leasing is done through Ozark's geological staff, who also

Jan 11, 1986

By S. K. Kawatra, T. C. Rao, J. P. Barnwal, Durga D. Patil

Coal macerals differ widely in their surface properties and in their hydrophobicities. Therefore, it is necessary to study the flotation time dependence of coal macerals using varying concentrations of various frothers and collectors. In the present study, froth flotation is used to explore the possibility of segregating coal macerals based on their relative rates of flotation. Petrographic analysis of the various macerals in the concentrate were carried out, and the results are expressed in terms of the recoveries of various maceral groups and mineral matter. Results show that it is possible to recover a good volume of the reactive macerals without mach loss of calorific value.

Jan 1, 2000

By G. Tapia, R. J. Kelley

Empresa Minera de Mantos Blancos S.A. successfully commissioned two copper SX-EW plants in late 1995. The design of these solvent extraction plants is such that chloride tenors of 30-35 g/l can be tolerated in the leach solution with no contamination of the electrolyte. The design was carried out in conjunction with Bechtel-ARA engineers and was based on the successful application of the available technology in the market; this mainly focused on decreasing the aqueous entrainment in the organic phase. This entrainment can reach 20,000 ppm in conventional plants.

Jan 1, 1998

By Alex Harrison, K. Payne

Computer generated magnetic field reference signa- tures of steel cord belt splices are used to evaluate lay-up and fabrication irregularities of splices in operating conveyors. Used as a quality inspection tool, magnetic signature analysis is useful in auditing data collected by general non-destructive testing (NDT) consultants. The evaluation can detect irregularities that weaken a splice, as well as detecting signature changes that can be indicative of adhesion loss. The evaluation can be applied to any NDT data available from a variety of commercial sources, which means that independent review of critical splice data is possible.

Jan 1, 1996

By J. D. Miller, C. L. Lin

Liberation of valuable minerals during size reduction is an important aspect of mineral processing technology. In practice, most quantitative information on liberation is based on the application of stereological theorems for the analysis of image data from two-dimensional polished sections. On this basis an estimate of the volumetric grade distribution is made. Recently, a new method based on cone-beam xray microtomography has been used for direct determination of the three-dimensional liberation spectrum of multiphase particles 100 microns in size or less. Preliminary results for a packed bed of particles indicate that high spatial resolution (approximately 15 microns) and the direct processing of raw volumetric data are two important benefits offered by this new method. Three dimensional liberation analysis by microtomography provides an excellent opportunity to overcome many of the limitations of currently used polished section techniques. For example, detailed textural information is provided. Of course microtomography provides an independent method to verify current procedures used for analysis and transformation of polished section data into an estimate of the volumetric grade distribution. More important, however, is the possibility that this method could be developed as a routine procedure for liberation analysis in the 21st century.

Jan 1, 1997

By Tevfik Güyagüler

Airborne dust is one of the important environmental problems in mines. Besides conventional dust control methods, recently, extensive studies have been carried out on the elimination of dust before it has actually been formed. Determining to what extend rock characteristics influence the amount of dust produced during different mining activities are considered as a guide for this purpose. The factors analyzed in this study were main mechanical, physical properties and petrographical constituents, namely free and combined silica. In the study regression analysis techniques were applied to investigate the effectiveness of aforementioned factors. INTRODUCTION Nearly every aspect of mining activity contributes to the air pollution caused by dust. Therefore the harmfull effect of airborne dust has been investigated many years and limit dust concentration levels were determined for various types of mine dust. To keep the dust level below limit value different dust control techniques have been applied in mines. So far, the well known techniques regarding dust control focuses on reducing the amount of airborne dust. However, recently various studies have been carried out to avoid the dust before it has actually been formed (Bhaskar and Gong, 1991). In this respect, influence of rock characteristics on dust formation is regarded as a guide for this purpose. The present contribution describes such a study in which the drilling operation is considered as the source of the dust. In this study drilling and dust sampling process were undertaken in a model gallery that simulates an underground working. The mechanical and physical properties of the rock samples were measured in rock mechanics and ore dressing laboratories. Quartz and combined silica contents of the rock samples, on the other hand, were determined in the laboratories of geological engineenring department. Rock samples used in the research were different types of coal measure rocks, namely, sandstone, shale and conglomerate. The rock characteristics studied in this work are brittleness, toughness, rock strength, hardness and hardgrove index as inherent properties; free silica, and total silica contents of rock samples as petrographical constituents. Although there have been various studies to determine the effect of rock characteristics on the dust formation, still the type and extend of effectiveness have not been understood clearly. LITERATURE REVIEW Most of the studies investigating the effect of rock properties on dust formation concluded that they are effective. In such an investigation, it has been found that inherent rock properties influence dust formation (Das, 1973). In the another study, dustiness of the air was considered as a function of the composition, hardness and moisture content (Panov, 1967). It was also accepted that in a drilling operation more fine dust is produced if the rock to be drilled is hard (Skochinsky and Kamarov, 1969). In some other investigations dust production were considered as a function of hardgrove index (Moore and Bise, 1984) or formulated in terms of brittleness, toughness and hardness (Güyagüler, 1991). The effect of the petrographical properties of coal or rock on dust formation characteristics have also been studied (Baafi, 1979) (Panov, 1967). Because of its importance, various researches were conducted the study to find out the effect of free and combined silica content of dust on dust formation. In one of the study, the relationship between quartz in the coal seam and quartz in the airborne coal dust was investigated (Ramani et al, 1988).

Jan 1, 1993

By Mortimer J. Richardson, Earl H. Malmstrom

INTRODUCTION The art of placer gold mine evaluation and mining has had an interesting evolution beginning in earliest times. DE RE METALLICA (c.1556), documents the use of rockers, circular sieves(jigs) and riff lest for classifying, concentrating and recovering placer gold, respectively. During the late 1800's in the heat of the international gold rush, a bucket ladder mining dredge containing its own processing plant was developed that enabled digging of placers to bedrock that were inaccessible to the hand miner. The power driven churn drill was developed at about the same tie that facilitated more rapid and larger scale sampling of placers to bedrock. The mineral jig was applied in the early part of the 1900,s to begin the replacement of riffles on placer dredges. Mining dredges proliferated in California and New Zealand to mine the deeper placers and spread throughout the world. The companies that were leaders in dredge mining technology conducted experimental work that advanced the state of the art by processing of gravels with jigs and amalgam systems to recover gold on board dredges in a continuous process. This paper will synthesize the technology of placer gold exploration, mine development and operation into guidelines for evaluation and development of small-scale prospects. Prospect Reconnaissance The location of a prospect usual1 y results from some physical evidence of the presence of gold and/or past mining activity. Any earlier activity that may have produced gold from the prospect, should be investigated before making the trip. The initial reconnaissance should attempt to verify a near-surface presence and then make observations concerning the geomorphic characteristics that relate to placer gold accumulation. Estimates of the probable depth, breadth and length of mineable gravels can be made from the surf ace by the experienced placer mining engineer. With this information, he can speculate on whether there is a viable prospect to be pursued. The placer mining engineer should be experienced in panning samples found in shallow diggings or from existing pits. This will give him immediate indications of gold presence without fear of "salting" by an over-ambitious promoter of the project. The same capability of panning is important during the other sampling phases. A thorough knowledge of logging and calculating the results is essential to proper evaluation of the deposit' s tenor. Evaluation Methods Depending upon the character of the prospect such as river, benches, terraces, jungle, the type of equipment to conduct sampling of the deposit must be determined. In most cases, the drill has replaced bulk sampling. The churn drill has had the greatest amount of accumulated experience but is slow. The reverse circulation drill (RC), is limited by its lack of verification in subsequent mining in order to prove its reliability. However, in the hands of knowledgeable placer mining engineers experienced with its use and calibration, it may be used. The RC Hammer drill (such as the Becker), can be as much as ten times faster than the churn drill and compress the time necessary to prove a prospect, or, to disprove it. All costs in balance, it is often cost effective over the churn drill.

Jan 1, 1987