Search Documents

By Kenneth L. Rubow, Virgil A. Marple, Ye Tao

Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective sampling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler. Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8µm while mineral dust is greater than 0.8 µm. One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the large nonrespirable particles while the inertial impactor stage, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles (<0.8 µm and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol.

Jan 1, 1991

By I. Longson

Maintaining control over underground environmental conditions in the United Kingdom is increasingly dependent on the contribution of underground booster fans. Given the recent trends of higher rates of production from a fewer number of coal faces with higher levels of mechanization and higher power consumption, the effect has been to place a greater load on the mine ventilation system. This has increased the scale of potential problems that may arise should any of the main ventilation control devices not perform at the required full duty. This is particularly true for underground booster fans. Major changes occur in the main ventilation parameters on the stoppage or restart of a booster fan which results in a temporary loss of environmental control. This paper analyzes the impact of such events and details a mathematical model thar has been developed for a single-mesh circuit containing a main and a booster fan. Predictions based on this simple model are presented and discussed with particular reference to the energy changes occurring within the ventilation system immediately following a booster fan stop or restart

Jan 1, 1995

By James H. Nulty, Joseph S. Roti

INTRODUCTION During a recent panel discussion on the topic of millwater antiscalants, the question was posed: "What would you like to see in the future?" Answer: &apos;We need an antiscalant that: can be fed without a pump (no maintenance), functions on residual basis (no fault), can be tested for colorimetrically in sub-part-per- mi 11 ion concentrations (no guessing) and will recycle back to the mill from tailings (no cost).” Impossible? Based upon today&apos;s level of technology, such a product does not exist. However, a few of the qualifications listed above are certainly food for future thought. Meanwhile, progress is being made in upgrading three essential elements in this critical area of ore processing. They are: 1. Antiscalant reagent research and development. 2. On-line monitoring programs. 3. Reagent storage and feed systems. The objective of this paper is to out- line the current direction being taken in each of these areas and to present case histories as examples of how theory has been applied in field situations to better improve operations. LABORATORY SCREENING TESTS Recent technical papers have explained the various generic chemical raw materials which are available in the marketplace. While the merits of each chemical component are open to debate, the processes used by most major reagent suppliers to evaluate products in the laboratory are fairly standard. Common techniques incorporate both static and dynamic conditions in the search for the most cost effective product. Static Test Perhaps the most common test procedure used is based upon NACE Standard Test Method 03-74, which is "a laboratory screening test to determine the ability of scale inhibitors to prevent precipitation of calcium sulfate and calcium carbonate from solution." The objective of this test is to measure the change in calcium ion concentration in a container of saturated stock solution prepared from calcium chloride and sodium carbonate which is heated in a water bath. After 12 hours at constant temperature (160°), the mother liquor is pipetted into a beaker and a titrated for gm/l of unprecipitated calcium ion. A simultaneous test is performed on stock solution with antiscalant added. The results are then charted to determine the most effective antiscalant (with respect to preventing precipitation of calcite). It should be noted that this procedure examines only the ability of a chemical additive to retain calcite in a saturated solution where thermal stress is applied. This is commonly referred to as sequestration or stabilization. It has been documented that products which act in this manner (i.e., inorganic and organic phosphates) are good scale inhibitors. However, low molecular weight anionic polymers function in a much different manner by distorting calcite crystal size, shape and charge density, thus preventing scale formation. Because of this different mode of operation, static tests may not prove conclusive where polymers and sequestrants are being compared. The simplicity of this test makes it easily adaptable for field use, although modifications are often made.

Jan 1, 1986

By J. K. Phiri

Copper mining is the main activity in Zambia and is confined to the large scale operations, mainly on the Copperbelt. The Copperbelt covers an area of size l00km by 50 km with a total of 10 underground and 5 open-pit mines operated by Zambia Consolidated Copper Mines (ZCCM) Limited. Most of the operations in these mines involves drilling and blasting. The loading of broken materials is by both manual and mechanical operations. Among the many risk factors associated with mining on the Copperbelt, is the occurrence of Pneumoconiosis which in the recent past has become quite prevalent and thus an important occupational health hazard for the industry. This study was carried out with the aim of establishing trends of pneumoconiosis incidence through the annual data collected by Pneumoconiosis Medical and Research Bureau of the Ministry of Health in Zambia, so that a basis could be formed for future research work. The study covers over 1,000 certified cases of Pneumoconiosis between 1960 and 1990

Jan 1, 1993

By H. Nemutolluhi

Discussion by G.E. Agar In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to he done, wet or dry or a combination? On top of that uncertainty the author refers to a simplified "Anaconda" test. No reference is provided for this procedure and in the text the results of the technique are referred to "Denver wet ball mill" results and say nothing of Anaconda results. Reply by H. Nematollahi I think that the method proposed to determine the Bond Work Index in this paper is clearly described in the paper as follows: •The method of grinding is dry (Ref. paragraph I, subject Method description); •The size of ball mill, the quantity and size of balls are noted (Ref. paragraph 1, subject Test equipment); and The test procedure is described in detail (Ref. paragraphs 1, 2 and 3, subject Test procedure). As it is noted in the paper, the test has been worked out under the same condition as Standard Bond Test with ball mill, so dry (screening should be dry also), but using a smaller ball mill and a smaller quantity of sample. Considering the above mentioned points, I believe that the method has been fully and clearly described and it ought to be repeatable as well. The Anaconda test is a method for determination of Work Index and could be done by any types of laboratory wet ball mill (Yan, R.F., et al., cf. References). I applied this method using a laboratory Denver ball mill (Ref. paragraph I subject Determining the Bond Work Index). So the results referred to Denver wet ball mill can be equated the same as Anaconda method.

Jan 1, 1996

By Ing Newton Amegbey, Joseph Afari Idun

Ashanti Goldfields Corporation (Gh) Ltd., the leading gold mining operation in Ghana is embarking on a major rehabilitation and expansion programme to increase gold production. A new southern ventilation district was targeted for this programme, and the ventilation system was to be reviewed in order to cope with increased production. The southern ventilation district was previously ventilated by booster fans. This arrangement was however, inadequate to solve the problem of the need to reduce smoke clearance time of the production areas, and to generally improve the underground ventilation conditions. Fan maintenance costs increased with the number of fans installed in the booster fan arrangement, and the fact that the fans were installed underground made maintenance difficult and took longer time. It became necessary to consider the installation of a new main fan on the surface. This paper gives an overview of the ventilation systems of the southern ventilation district of the mine before and after the new main fan was installed. The field tests carried out on the fan to ensure that it complied with supplier&apos;s specifications are described, and the new system analysed to see it&apos;s effectiveness.

Jan 1, 1993

By T. V. Vasudevan, J. Blaakmeer

Adsorption experiments were conducted at two different solid loadings to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region 11, while surface precipitation was predominant in region I11 along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1988

By Conrad G. C. Douglas, Parris A. Lyew-Ayee, Vincent G. Hill

ABSTRACT Distinct patterns are identified in the associations, distributions, and levels of concentration of the silica minerals, boehmite, aluminous goethite, and phosphate minerals in the bauxite deposits of Jamaica. These result from syngenetic and diagenetic reactions associated with post-bauxitization tectonic and associated activities. Three basic types of bauxite are identified, viz., Jamaica-1 (< 3.0% boehmite), Jamaica-2 (> 3.0% boehmite and 30-80% of the iron as aluminous goethites), and Jamaica-3 (> 3.0% boehmite and > 90% of the iron as aluminous goethites). The Jamaica-1 type has a mean value of < 2% boehmite as A1203, while this level in the Jamaica-2 type is usually about 3.5%, and > 4% in the Jamaica-3 type. Similar discrete associations were found for the species and concentrations of aluminous goethite and phosphate minerals. The process and geological implications of these are discussed.

Jan 1, 1984

By Robert Cooke

This paper shows how technology developed to analyse stabilised slurries can be applied to paste flows. The rheological characterisation of paste mixtures using the generalised yield pseudoplastic rheological model is described. It is noted that the slump test does not provide a complete rheological characterisation of a paste. Methods for calculating pipeline pressure gradients for laminar and turbulent flow are presented. The minimum pressure gradient is an important consideration to ensure that solids do not settle on the pipe invert. Important points to be considered for a pipe loop test programme are noted. The usefulness of the pseudo shear diagram for scaling pipe loop test measurements is demonstrated. Issues to be considered for the design of paste reticulation systems are discussed.

Jan 1, 2001

By Tzou-Shin Ueng

Rock reinforcement of rock anchors and rock bolts are commonly used for the support of large rock caverns. The rocks at the location of most large underground openings are usually under very high initial stresses prior to excavation. Hence, the stress redistribution caused by excavation will induce considerable rebound deformations of rocks surrounding the caverns. Since the pressures exerted by the reinforcement are generally far below the initial rock stresses, the reinforcement will be stretched along with the rock deformations, and the stresses in the reinforcement increase accordingly. It is not uncommon for the stress in the reinforcement to reach the yield strength, and in some cases the reinforcement may even have failed. Therefore, the increase of stresses caused by the rebound deformations of rocks should be taken into account in addition to the force required to stabilize the caverns. It was found that the measured stress increases of the prestressed tendons after installation were in good agreement with those computed based on the measured rock deformations between surface and the anchoring point of the reinforcement. The rebound rock deformations and the stress increases in the reinforcement can be estimated based on the results of the finite element analysis and experiences in previous field measurements incorporated with considerations of the geologic conditions, rock properties, rock reinforcement and construction procedures.

Jan 1, 1986

By Sterling S. Cook

The U.S. Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and ASARCO Santa Cruz deposits in Arizona to further our understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/l copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/l copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration (up to 40 g/l) while illite and sericite had minimal impact. Biotite, calcium-rich clay and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentrations increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K-feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1988

By Robert J. Timko, Lincoln Derick

This work is a follow-up to previous research that attempted to predict the location of spontaneous heating episodes in underground coal mine pillars. The objective of the original work was to see if the data obtained by commonly used detection methods could accurately predict spontaneous combustion episodes in coal pillars. Data accumulation during the study was enhanced when a spontaneously generated fire occurred within one of the pillars being examined. The fire provided researchers with realistic data that could be used to determine if fire prediction was possible. Results from the initial study found that the atmospheric status equations that were used provided little advance notice that combustion would occur where it did. This study reevaluated the accumulated data by applying it to recently developed equations and compared these results with previously obtained information to determine if a combination of these techniques could more effectively predict impending combustion.

Jan 1, 1995

By Rudolf Greuer, Gerald Jalkanen, Huann-Sheng Chen

A short cut is presented where the average grade above a primary grade cutoff and its associated byproduct grade(s) are estimated by screening the primary and byproduct grades. For the primary variable, choose samples whose grades are above a cutoff of interest. Compute variograms for the subset of the primary variable. Then using this variogram, krige the blocks of interest only using the samples whose grades are above the cutoff. The next step is to screen byproduct grades by choosing byproduct samples whose associated primary grades are above the cutoff of interest. Next compute variograms for this subset of byproduct samples. Then using this variogram, krige the blocks of interest using byproduct sample grades whose associated primary sample grades are above the cutoff of interest. The results are the average grade above a primary cutoff for both the primary and the associated byproduct variables. Using two simulated primary and reference data sets a case study resulted in the screening krigings performing better than the indicator kriging approach in the first case study. A second case study had mixed results with the primary indicator approach performing better than the primary screened approach. The byproduct screened approach performed better than the byproduct indicator approach.

Jan 1, 2002

By W. P. Blacutt

A financial-economic model incorporating physical, market and policy variables has been developed for mining investment in Bolivia. Additional risk criteria emanating from political instability, new mining legislation, recent environmental regulations and a new minerals taxation system are accounted for and are integrated into the investment decision model. Results of the model indicate that geologic and market variables have the dominant effect on the investment-worth function. Among policy variables, exchange rate and taxation policies have the most significant influence. Depreciation allowance for infrastructure development has negligible weight in the investment-worth function. The business structure of the firm considering investing in the Bolivian Polymetallic Project, is found to be an instrumental factor in the investment-worth outcome.

Jan 1, 1995

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24v0 of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50v0 of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include: • extraction of thick seam in ascending order with stowing; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. • Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof; four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 1, 1988

By J. K. Mohanty, D. Panda, P. K. Sahoo, R. K. Paramguru, K. C. Nathsarma

Ferromanganese slag, a product of the manganese industry, was characterized mineralogically. The slag, which contains high Mn values, was characterized using optical microscopy, XRD analysis and electron microscopy. No separate Mn-bearing oxide mineral phase was found. The slag is amorphous, and no crystalline phase was identified in the hulk sample by XRD, However, in. fine fractions, quartz was identified. Scanning electron microscopy (SEM) revealed the presence of Mn, Si, Al and Ca in the matrix without the development of a mineral phase. Leaching experiments using H2SO4 were carried out to determine if Mn could be extracted from the slag. At room temperature, almost 100% of the manganese could be dissolved at a solid-liquid ratio o f 1:10 by leaching with dilute sulfuric acid. The impurities could be precipitated by pH adjustment to produce a manganese sulfate solution suitable for the production of MnO2 or electrolytic Mn metal. Based on the laboratory-scale experiments, a suitable process is proposed to recover manganese values from the, ferromanganese slag.

Jan 1, 1999

By William H. Meadows

This information describes the ventilating and methane gas testing procedures utilized during the raising of a mine shaft using a Robbins 81-R drill. An overview of the raise boring process is presented to illustrate the ventilating and gas testing procedures. A mine shaft project, 4.88 m (16 ft) in diameter and approximately 457.2 m (1500 ft) in length, will be the focal point of the presentation, with reference to similar projects for additional comments on variations in procedure.

Jan 1, 1980

By Balesh W. Konda, Andrew B. Cecala, George W. Klinowski

Methane ignitions continue to be a major concern to the longwall mining industry. In spite of numerous advances in technology over the past decade, there has not been a measurable reduction in the number of longwall face ignitions. These ignitions will continue to be a problem as deeper and gassier seams are mined, as production rates are increased through numerous improvements in longwall mining equipment, and as the output of the workforce increases due to improved management-labor relations. It is necessary to know methane liberations, emissions, and flow patterns in order to effectively deal with it and to design control technology to reduce the occurrence of longwall face ignitions. A cooperative research project between the Bureau of Mines and the Canada Centre for Mineral and Energy Technology (CANMET) has been established to address longwall methane problems. The initial direction of this work was to look at methane flow patterns during the entire longwall mining process, and more specifically to examine and compare methane levels and flow patterns for advance and retreat methods of longwall mining. Both advance and retreat longwall mining is practiced in the Sydney coal fields in Nova Scotia. In 1986, a study was performed on advancing longwall panels at the Lingan Colliery, and a similar study was recently completed at the Phalen Colliery on a retreating panel. Methane monitors were placed at various locations along the face, intake, return, and bleeder airways. Handheld methane monitors were also used upstream and downstream of the shearer mining machine. This setup allowed a determination of methane sources on the longwall panels, including: liberation from cutting with the shearer mining machine, emissions from the coal seam along the face, emissions from the gob area, and methane already in the intake air. The results from both studies are reported and the differences between the two longwall mining methods compared.

Jan 1, 1989

By Robert A. Haney

Utilizing the recently developed laser velocimeter and a Pitot-static tube, the United States National Bureau of Standards (NBS), has calibrated various types of anemometers that are commonly used in the mining industry. This paper presents a summary of the performance characteristics including accuracy, precision, starting and stopping speeds of each instrument tested. The specific instruments that were calibrated by NBS have become Mine Safety and Health Administration (MSHA) primary reference instruments. These primary reference instruments are used in turn to calibrate secondary reference instruments for each Coal Mine Safety and Health District. Each District calibrates anemometers that are used by District engineers and inspectors. Calibration is accomplished through a substitution procedure in which the reading on the anemometer is compared to the true velocity determined by the reference instrument. Calibration is performed over the entire range of the instrument using an open jet wind tunnel to produce the various approximate velocities. Some specific details of the calibration procedure are presented in this paper.

Jan 1, 1980

By Dorothy A. Canter

Three Federal programs exist for identifying significant environmental chemicals, including minerals, that should be tested for toxicological effects. Two programs are mandated by law and can lead to industry-funded studies; they are administered by the Environmental Protection Agency and the Agency for Toxic Substances and Disease Registry, respectively. The third is the National Toxicology Program, a Federally-funded testing initiative. This paper summarizes the three programs, describes their similarities and differences, and discusses their applicability to minerals.

Jan 1, 1991