Search Documents

By James J. Scott

Shale formations are the Nemesis of the Mining Engineer. Shales react to changes in environment in the most unusual and unpredictable manner. Increase in temperature may cause spalling, increase moisture and compression induced fractures may occur, and if a full face is exposed it may deteriorate due to atmospheric exposure. Combine only small amounts of shale in layered fashion with hard brittle competent rock and the whole structure may be fractured and fail due to stresses generated in and around the shale. In this paper the author will discuss failure mechanisms encountered under various field conditions and remedial action which may be employed by the engineer.

Jan 1, 1969

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By Rob McIvor, Joe Keating, Gary Simmons

As more complex ores are processed, finer grinding becomes more necessary. A cross section of several industries will be presented with discussions not only of find grinding issues but also the classification of fine particles. JOHN MANSANTI: Our next topic will be fine grinding. Again, the intent is to present a topic that is generic enough to apply to multiple industries. Our first speaker is Gary Simmons. Gary is filling in for Phil Walker from Twin Creeks. Phil was not able to join us this week, because of some issues they're having with the autoclave. Gary, being involved in the development phase, is very familiar with the topic. Gary spent about three years with American Cyanamid and another four years with Noranda. He also spent some time with Meridian Gold, then became the director of metallurgy with Santa Fe Pacific Gold. He spent seven years there and is presently the director of process technology with Newmont Gold.

Jan 1, 1998

By Sharad Mathur

The purpose of this paper is to present the benefits of high reactivity meta kaolin (HRM) in high performance cement-based systems. HRM, unlike other pozzolans, is manufactured from selected naturally occurring kaolin ore and carefully processed under stringent conditions to result in a consistent product with highly pozzolanic properties. HRM is an ultrafine pozzolan that enhances the mechanical properties (workability and strength) and chemical stability (durability) of Portland cement concrete and cement-based products. HRM is unique with respect to its white color which makes it an ideal choice for architectural applications where visual and aesthetic concerns are critical.

Jan 1, 2003

By Omar A. Muhtadi, R. Bruce Thorndycraft, David A. Milligan

9.1 INTRODUCTION Precious metals in a leach solution are extracted, concentrated, and purified to complete the process begun in the heap and to produce an end product which will provide an economic payback to the mine developer/operator. Several different processes are required to convert the dissolved precious metals into pure metal bars. This chapter discusses the actual production of metal once it has been recovered from the pregnant leach solutions by the zinc cementation (Merrill -Crowe) or carbon adsorption processes. Metal production is generally taken to mean the production of a fairly pure "dore" bar. This chapter also reiterates some information from Chapter 8 in a slightly different context, since the focus of Chapter 8 was a fairly detailed description of the two actual recovery processes, whereas the focus of this chapter is metal production. The sale of an intermediate precious metal product is possible (as opposed to the production of dore bars at the mine site); however, the value of the precious metals is reduced by the various charges and risks associated with precious metal processing. For this reason, most operators choose to produce the most refined metal possible in order to maximize project economics. Precious metals may be extracted from the leach solution by both conventional and unconventional processes. The conventional processes are activated carbon/electrowinning (ACE) and zinc precipitation (ZIP). The unconventional processes are resin ion exchange, solvent extraction, and direct electrowinning. A typical ACE process has two circulating loops. The first loop adsorbs the cyanide-metal complexes from the dilute leach solution onto the activated carbon. A second, separate solution loop removes the cyanide-metal complexes from the activated carbon into a strong solution, the electrowinning electrolyte. Activated carbon is transferred from one fluid loop to the other. The operating cost of the ACE process is directly proportional to the quantity of carbon stripped and thus to the quantity of precious metal produced. A typical ZIP process contains a single circulating loop. The solution is filtered, deaerated, contacted with zinc, and filtered again. The barren leach solution is then returned to the heap. The zinc sludge recovered in the

Jan 1, 1988

By K. C. Nathsarma

An attempt was made to extract niobium oxide from ~98.5% Nb2O5 using solvent extraction processes. Nb2O5 is used as the feed material in carbothermic reduction processes aimed at producing high-homogeneity, super-conductor-grade niobium on a laboratory scale. The Nb metal used for superconductor applications requires a residual resistivity ratio (RRR) > 300, which in turn needs a stringent purity of Nb and allows impurities (substitutional and interstitial) in ppm levels only. In this paper, solvent extraction of niobium was studied under various experimental conditions, such as effect of different extractants, concentration of methyl isobutyl ketone (MIBK) in the organic phase and concentration of various acids. The concentrate was digested with hydrofluoric acid, with ammonium fluoride (NH4F) as a stripping agent. The extraction of niobium from low hydrofluoric- (HF-) bearing solution was found to be low. Thus, various concentrations of hydrofluoric acid and sulfuric acid, as well as hydrofluoric acid and hydrochloric acid, were investigated towards obtaining a maximum amount of niobium in the filtrate and a minimum amount of niobium in the residue. A McCabe - Thiele plot for extraction of niobium from the aqueous phase, HF-bearing solution using HCl with 85% MIBK in kerosene has been constructed to determine the O:A ratio and the number of stages of the process.

Jan 1, 2011

By L. S. Rubin

The efficient and acceptable disposal of fine coal refuse (28MxO) is one of the highest priority problems facing the coal industry today. For many years the established system for the disposal of this fine refuse slurry has been to concentrate the solids in a static thickener and pump the resulting 20-40% solids underflow to lagoons or impoundments. Although this technique has served the coal industry well, increasing environmental concerns and refuse related disasters, such as Buffalo Creek, West Virginia and Aberfan, Wales, Great Britain have resulted in federal and state regulations which now control fine refuse disposal methods. As a consequence of these regulations, the capital costs of constructing, maintaining, and operating regulatory complying impoundments has become in many cases economically unattractive. Areas processing topologies similar to those coal preparation plants of the Appalachians are particularly burdened by these regulations and are consequently turning to alternatives for handling and disposal of their fine coal refuse. The basic requirements of impoundment alternatives as defined by environmental and plant demands are: (1) A relatively solids-free liquid (1000 ppm or less) to serve as plant make-up water in a "closed circuit" system, and (2) a sufficiently dewatered solids product which can be combined with the coarse refuse to form a compactable stable land-fill.

Jan 1, 1978

By John Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has collected pillar and span data at 34 stone mines in 10 states to develop pillar and roof span design guidelines for underground stone mines. Pillar, floor and roof conditions each contribute significantly to the overall mine stability. The roof may be stable for a century, or it may appear to be stable but fail with little warning. Clearly, an assessment of the mine roof is critical to the safety of these operations. However, up until now, the assessment of the mine roof came primarily from exposures in roof falls or portal areas. This provides only limited information, and a more proactive approach is needed to assess changing mine conditions. A separate effort was undertaken to examine the roof structure with the use of a borescope. Numerous physical and geologic roof structures were observed with a stratascope/borehole video camera. The objective of this work was to develop a technique of assigning numerical values to features seen within the mine roof and apply those values to formulate a roof stability evaluation. Such features as changes in color, grain size, and general lithologies are readily observed. Minor structures in the rock, fossils and fractures are also readily identified. Each feature may have a variable and site-specific impact on roof quality. A number of mines were visited and a series of holes were borescoped in each mine. The features identified in the roof were classified and potential for roof damage related to each feature was assessed. A process is presented that relates the structures and their locations to provide a numerical value, or roof quality index that can be used to assess roof stability.

Jan 1, 2009

By R. A. Metz, James W. Clark, William C. Dixon, Kevin L. Wiley, Thomas R. Couzens

This paper is a description of certain geologic aspects of the Inspiration mining operation. It is not a geologic description of the Inspiration deposit nor an exposition of all the geologic work involved in the development and exploitation of the deposit. A few specific examples of the application of geology and geostatistics to the mining process are given to illustrate the progress that has been made in making the Inspiration Mine more efficient and cost effective, and a statement of the philosophy of geologic applications is offered.

Jan 1, 1992

By Alan E. Isaacson

Extensive gravel deposits exist within a six-county area in the mountains surrounding the Salt Lake Valley, and in the mountain ranges to the west. The six-county area includes Davis, Salt Lake, Summit, Tooele, Utah, and Wasatch Counties. The majority of these are beach deposits from prehistoric Lake Bonneville. However, real estate development associated with a projected population increase of 54 percent over the next 20 years is expected to remove most gravel deposits in Salt Lake County from consideration for mining, forcing gravel operations to relocate from eastern Salt Lake Valley to the Oquirrh and Stansbury Mountains farther west. The gravels in these ranges are of lower quality and require additional processing to manufacture asphalt and concrete. Replacing gravel resources along the Wasatch Front with resources in the Oquirrh and Stansbury Mountains over the next 20 years has the potential to increase construction costs by nearly $1 billion. The majority of this cost (82 percent) is the result of increased transportation costs due to longer distances to market. The remainder of the cost is attributable to lower quality gravels that will require additional processing in the manufacture of asphalt and concrete. The following analysis and discussion does not take into consideration the amount of crushed stone that is currently being used in the construction industry in northern Utah, its use as a substitute for lower quality gravels, or as a factor in the base case projection.

Jan 1, 2001

The concept of optical basicity is now being widely applied to rationalize and predict the chemical properties of slags. It employs signals from a probe ion to indicate the "state" or relative "freeness" of the oxygen ions in the slag, and hence provides a fundamental measure of slag basicity. Values of the bulk optical basicity of a slag can either be measured spectroscopically in samples of transparent solid glassy slag, or calculated very simply and accurately from the chemical composition of the slag. The way in which these values vary in different systems are illustrated as isoptical basicity lines on ternary diagrams, and the patterns obtained are discussed. The difficulties associated with assigning optical basicities to the oxides of transition elements are also reviewed briefly. It has been demonstrated that these bulk values can be used as the basis of a flux control model for steelmaking to achieve end-point chemistries much more reliably. Furthermore, several correlations have been established which allow the prediction of the slag-metal distribution of various solute elements. This approach has been used to predict the phosphorus distribution at the end of steelmaking, and also to custom design fluxes for the ladle and tundish to aid in the control of residual elements in the steel such as suphur, hydrogen and nitrogen.

Jan 1, 1990

By R. K. Devala

In this paper, numerical approximation schemes, for solution of the mass transfer problem in mine ventilation have been developed by using three implicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments, using the concept of Root Mean Square error. For implicit finite difference schemes, in general, the modified central difference scheme is better than the two other schemes at lower velocity. Also, at lower air velocities, implicit schemes underpredicted the concentration values. At higher air velocities, the Crank-Nicholson and Laasonen schemes provided better results than the Modified Central Difference scheme.

Jan 1, 1994

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By Daniel Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abundant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleistocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional resources. Limestone uses include cement and lime manufacturing, concrete sand and aggregate, mad base material, beach sand replenishment, agricultural lime and golf course construction.

Jan 1, 1982

By Scott G. Britton

The first section of this text delves into construction engineering techniques for successfully completing necessary underground production support projects. I will discuss alternative design concepts, installation practices, materials and material costs, completion time, and necessary labor for individual projects. The emphasis of this section is on describing each project thoroughly and providing a practical guide for the supervisor or engineer. There are four main construction categories for typical underground mining projects. These are: 1) Transportation of men and supply materials. This refers to track and wire installation and roadbed grading and ballasting. 2) Ventilation, composed of overcasts, man doors, regulators, and stoppings. 3) Drainage, including sumps, pumping stations, drainage networks, pumps, and face drainage. 4) Haulage of coal and rock from the face to the outside. The focus here is in the installation of belt lines, belt drives, transfer points, and vibrating bins/feeders. The first section shall fully discuss these four categories in regard to the construction engineer or supervisor designing, building, or improving a system. In addition, special projects such as surge bins, rotary dumps, and underground offices not classified under these categories will be discussed. For manageable purposes, I have limited the installation discussions to one or two approaches I feel have merit. The variation of installations in coal mining is endless, each with its own advantages and disadvantages. Therefore, the reader should not dismiss or restrict his thinking to only the approaches in the text. It serves as a guide only.

Jan 1, 1983

By R. W. Bartlett

Computer deterministic models for predicting the time dependent extraction of copper by leaching fragmented rock (both in situ and heaped or piled) have been presented in the last two years by Bartlett1, Braun, Lewis and Wadsworth2 and Roman and Co-Workers.3 All of these models involve aqueous diffusion within the pores of the rocks from which the metal is being extracted. The rate of chemical dissolution of the ore mineral within the rock will also affect the kinetics in the case of sulfide copper ores and some of the more refractory oxide copper ores. Simulation is also needed for fine grain disseminated gold ores and low grade uranium ores that may be heap leached. The development of such leaching models has two major purposes: First, extraction estimates must be made for tong time periods particularly for situations where laboratory and field tests either cannot be made or where there is insufficient time for field testing. Second, the results of simulated leaching should indicate the relative importance of the extraction controlling parameters and, thereby, provide a better understanding of the complex leaching phenomena on heaped material being leached, and guide further experimental work.

Jan 1, 1974

By Geoffrey Purcell

The flotation response to amine collector of quartz and the feldspars microcline and albite, of the pyroxenes augite and spodumene, and of olivine can be, explained by a physical adsorption model. Flotation decreases in the order given above, and the different behavior of the three groups is attributed to structural variations of the silicates, With sulfonate collector both chemical action and physical adsorption play their part in producing hydrophobic surfaces, and flotation increases in the order given.

Jan 1, 1966

By Roger A. Kauffman, Dean Van Dyk

Feldspar is the earth's most abundant mineral group. The feldspars are aluminum silicate minerals belonging to the tectosilicate class. Feldspars are the most widespread of any mineral group and are estimated to constitute 60% of the earth's crust. They make up a large percentage of the exposed rocks as well as soils, clays, and other unconsolidated sediments. Feldspars are widely used in the glass and ceramic industry and are principal components in rock classification schemes. Feldspar minerals and their production are important contributors to the domestic and world economies and standard of living. In 1990, the United States produced 630 kt of feldspar minerals, and world production was estimated to be more than 5 Mt. Feldspar mineral production in the United States has a long and interesting history (Feitler, 1967, Rogers Jr. et al., 1983). The first commercial production in the United States occurred in about 1825 and came from pegmatite bodies located in Connecticut, where feldspar was mined, hand sorted, and shipped to England. Feldspar production grew during the 19th and 20th centuries with important developments in production location, integrated mine and processing facilities, and the development of the flotation process for feldspar by the US Bureau of Mines and the feldspar industry. The first commercial feldspar flotation plant began operations-in Kona, NC, in 1946, some six years after this process had been developed. In 1990, the domestic feldspar industry consisted of 12 operating companies with mines and processing plants located throughout the United States (see Table 1). During the last 25 years, the domestic feldspar industry has been dynamic, marked by new plant construction and capacity expansion at older plants. The industry has also seen plant closures, changes in ownership of existing operations, the consolidation of the Canadian nepheline syenite industry, and the increase of imported feldspar products. The industry has been affected by contractions in its major end-use markets brought about by economic cycles, product substitution, and environmental effects, such as recycling, land-use controversy, and air and water pollution. Despite problems, the industry remains mature and highly competitive. GEOLOGY Mineralogy The common feldspar group of minerals form a single crystalline phase or solid solution series of minerals. Fig. 1 is a ternary phase diagram that shows the feldspar mineralogy-KAlSi,O8, NaAlSi3O8, and CaAl2Si2O8. The end-member compositions are also referred to as potassium, sodium, and calcium feldspar. The feldspars whose chemistry ranges between the potassium and sodium end-members are known as alkali feldspars, while those between the sodium and calcium end-members are plagioclase feldspars. These feldspar groups can be further subdivided based on structural and compositional features within the alkali or plagioclase feldspar series. The distinction between and the proportion of members of the two feldspar groups are important to the classification of igneous rocks (Deer et al., 1966). Perthites are the exsolution product of an initially homogeneous potassium-sodium feldspar solid solution which forms (in an environment of decreasing temperature) a heterogeneous intergrowth of sodium-rich feldspar lamellae in a host crystal of potassium feldspar. Antiperthites are exsolution products in which the host mineral is sodium-rich plagioclase feldspar and the intergrowths are potassium-rich feldspar.

Jan 1, 1994

By Changwoo Lee, Jan M. Mutmansky

Introduction Recognition of Coal Workers' Pneumoconiosis (CWP) as a major occupational disease has affected various aspects of the coal mining industry in the United States as well as in almost all major coal producing countries. Regulations related to the control of coal mine dust forced mine operators to modify their mining and ventilation practices. As the coal production record of the last 15 years shows, this had both direct and indirect impacts on the productivity and production costs. To identify the causes of CWP, many research efforts have been made through- out the world. Most of these studies were epidemiological in nature, attempting to pinpoint exposure and seam variables that affected the incidence of the disease. Other studies have been oriented toward the elemental and mineralogical composition of the coal dust in the mine atmosphere and in the miners' lungs. These studies indicate that there may exist some relationships between the characteristics of the coal mine dust and the prevalence of the disease. Some of the variables that are thought to affect the occurrence of CWP are the mass of the dust in the working place, the rank of the coal, the existence of certain trace elements, the free silica content of the coal, and the existence of other minerals in the respirable dust. A more complete description of these previous re- search studies has appeared elsewhere (Mutmansky and Lee, 1984). The behavior of particles in the human lung is known to be governed by their aerodynamic diameter, which is defined as the diameter of a hypothetical spherical particle with unit density that exhibits the same settling velocity as the given particle. Because of this fact, the aerodynamic size distribution of coal mine dust is one of the parameters to be determined along with the other physical, elemental, and mineralogical characteristics. The objective of this paper is to establish a strategy for providing coal mine respirable dust samples for characterization purposes using instruments that classify according to the aerodynamic diameter. In addition, several findings concerning characterization methods will be presented. Choice of Samplers Most of the gravimetric dust collection devices that can be utilized in a mine environment can be

Jan 1, 1986

By Michel L. Bilodeau

Mineral exploration is a sequential information gathering process. Primary exploration programs filter favorable areas through a series of geological, geochemical, and geophysical tests resulting in the discovery of mineral occurrences. The most favorable of these discoveries provides economic justification for a delineation drilling program. The purpose of delineation drilling is to provide information for estimating relevant physical characteristics of the mineral occurrence. These estimates are used to evaluate the exploration project and, eventually, the economics of mine development. Delineation drilling normally completes the exploration process. If the assessed economic characteristics of the delineated occurrence provide justification for mine development and production, an economic mineral deposit is the end result of the exploration process. Subsequently, a development drilling program is initiated to obtain the necessary data for detailed mine planning. The delineation drilling stage is in itself a sequential investment process. As delineation information accumulates, the reliability of geological estimates is improved and, thus, the uncertainty associated with the assessment of profitability criteria is reduced. Delineation drilling should continue as long as the marginal benefits, which result from improving the reliability of profitability criteria, exceed the marginal costs associated with the additional drilling.

Jan 1, 1979