Search Documents

By Dennis C. Drehmel

Because of their relatively low cost, carbonate rocks are desirable in abatement of air pollution by acid gases. Although many processes and types of equipment have been proposed to control or prevent the emission of acid gases, this paper considers only three: dry-limestone injection, wet-limestone scrubbing, and chemically active fluid beds. For the dry-limestone-injection process, surface area-especially from pores in the 0. 2- to 0.3-micron range-is one of the important parameters which will discriminate between less and more reactive carbonate rocks. Marls, chalks, oolitic calcites, and other fine- grained limestones show larger-than-average surface areas and better- than-average removal efficiencies. Inert chemical impurities such as silica detract from reactivity. A dolomite is not necessarily less re- active than a calcite. For the wet-limestone-scrubbing process, dissolution rate of the carbonate rock controls the differences in stone reactivity. In this process the dolomites are less reactive than the calcites. In addition, more than 90 percent of the dolomitic impurity in Fredonia white lime- stone is inert during limestone scrubbing. Dissolution rate is also a function of particle size for large-grained carbonate rocks. Fine grinding of such rocks will increase the dissolution rate to that of a fine-grained rock. Hence the requirement of high dissolution rates may be met by some grinding of fine-grained material (e. g., marl, chalk, or other limestone) or by fine grinding of coarser grained material. For chemically active fluid beds, chalks have the best capacity to absorb both SO2 and H2S. However, most chalks are probably unsuitable for fluid beds because of high attrition rates. Because dolomites are generally more reactive than calcites with both SO2 and H2S, a dolomite would be the feed material of choice for a chemically active fluid bed.

Jan 1, 1974

By Joseph Moses Botbol

The disposition of world mineral resources is such that a vital need exists for both the most efficient development of existing resources and the rapid disclosure of as-yet undiscovered resources. The technological developments described in this report are directed primarily toward the acceleration and increased efficiency of mineral-resource exploration program. In the past decade the use of computers in the mineral industry has grown exponentially. Most computer applications in mineral exploration are designed to be implemented either before or after data collection. Few, if any, computer applications are designed to be used during the collection of data. One major reason for the lack of development of computer applications in this area is that comunications links do not exist between computing systems and the remote areas that host mineral-deposit exploration programs.

Jan 1, 1975

By Lewis. Clifford J.

The purpose of this article is to present design information and operating data on a pilot gas scrubber which is believed to be a new approach for removing noxious gases and particulate matter from the off gases of coal burning power plants and smelters. This principle of scrubbing gases, particularly, scrubbing with an aqueous slurry of lime, was conceived by the author early in 1972. The National Lime Association financed the design, fabrication and initial operation of the unit. The unit was fabricated by Hazen Research Inc. of Golden, Colorado. It has been tested on the off gases of two coal burning power plants and one smelter. The current environmental program has stimulated research and development activity directed toward the removal of sulfur oxides, oxides of nitrogen, particulate matter and other undesirable substances from gases discharged into the atmosphere. At present, most of this effort is focused on the removal of sulfur dioxide and particulate matter by aqueous scrubbing of the gases. This presentation deals particularly with the removal of sulfur dioxide using an aqueous slurry of lime as the scrubbing medium. In recent papers, the author has called attention to-the sludge problems resulting from aqueous scrubbing and to some earlier data on the pilot scrubber about to be discussed.1/

Jan 1, 1973

By Christopher M. St. John, Michael P. Hardy

INTRODUCTION Geotechnical models, particularly those based on the finite element method, have been available to aid in en¬gineering design of underground mining excavations for over ten years. Despite this fact there are remarkably few cases of their use in mine design documented in the literature. It is therefore to be anticipated that many potential users of these models are relatively unaware of their capabilities and limitations and also of the form and detail of geotechnical data needed for their success¬ful application. This subsection attempts to address this problem by discussing the different types of numerical models now available and by noting how some of them have been used to study a variety of problems associated with underground mining. The subsection concludes by discussing the applica¬tion of the displacement discontinuity method to the de¬sign of possible mining systems for the copper-nickel deposits of northeastern Minnesota. The object of the analyses, which were nonsite specific, was to determine the significance of geotechnical parameters, such as ini¬tial stress and rock structure, on the stability of under¬ground excavations and hence to provide guidance for future geotechnical investigation. NUMERICAL MODELS In the geomechanical design of underground mining openings, use is made of numerical models that repre¬sent or simulate the large-scale mechanical behavior of rock. There has been less interest in analysis involving fluid flow and heat transfer, but with increasing interest in such areas as in-situ retorting and solution mining it is likely that there will be a growing need for numerical models embracing and coupling all three physical proc¬esses. However, the emphasis in this subsection will be on mechanical behavior. Models which simulate such behavior will be divided into two groups: continuum models and discontinuum models. These will be dis¬cussed in turn in order that some insight into alternative solution strategies and their merits may be gained. Continuum Models Almost all geomechanical numerical models must be classed as continuum models even though particular computer codes incorporate special provisions for rep¬resenting discontinuities such as faults, bedding planes, or joints. They are continuum models because they pro¬vide solutions for cases where material behavior is governed by the differential equations of continuum mechanics. Two basic solution strategies for such equa¬tions may be identified immediately: the differential ap¬proach and the integral approach. In the differential approach a means of approximating the differential equations over the entire region of interest is sought. In the integral approach use is made of fundamental solutions from continuum mechanics, and these are used to construct a solution to the whole problem, making approximations only on the boundaries of the region of interest. The several differential and integral methods are identified in Table 1. Differential Methods: Problems in continuum me¬chanics involve the solution of three types of partial differential equations. Two of these govern the behavior in so-called initial value problems, in which variables change both in time and in space. Examples of such problems include nonsteady heat transfer and fluid flow, and stress wave propagation. The last type of partial differential equation governs the behavior in boundary value problems. In these, variation is in space but not in time. Solution of initial value problems may be achieved in two significantly different methods: implicit and ex¬plicit. The differences between these two methods will be illustrated by considering a very simple initial value problem, that of one-dimensional heat diffusion. The equation governing this process may be written as: [ ] where T is temperature, K is thermal conductivity, p is density, c is specific heat, t is time, and x is the spacial coordinate. In finite difference form this equation might be written as: [ ] where the superscripts refer to the time and the sub¬scripts to the spacial location. Several solution strategies for this equation have been used. Two important ones may be illustrated very simply by discussing the signifi¬cance of the superscript * on the right-hand side of the equation. If i + 1 is substituted for * then the second derivative of the temperature with respect to distance is evaluated at the end of the next time step (using tem¬peratures not already known). Such an approach leads to a set of equations involving unknown temperatures and a solution procedure which is referred to as being implicit. The important characteristic of the implicit procedure is that it leads to a set of equations that must be solved for each time at which the temperature dis¬tribution is required. If instead of substituting (i + 1) for the superscript *, i is substituted, the following equation is obtained: [ ] {In this case the new temperature is defined in terms of an already known temperature distribution. The solution procedure is now known as explicit and has the impor¬tant characteristic that there are no equations that have to be stored or solved. A practical advantage of this

Jan 1, 1982

By James P. Dorian

istorical records suggest that the gathering of geologic information in China began more than 2,000 years ago. Modern-day geological work in the nation started in the early part of this century but it progressed rather slowly. Before the founding of the People's Republic of China (PRC), there were only 800 people engaged in geological work and only 200 trained geologists among them. According to Minerals and Mining in China, many accomplishments were achieved within China's mining industry during the period of years between 1949, the founding of modern China, and 1997. These include: ? The number of types of minerals with verified reserves increased from 18 (pre-Liberation) to 162 (today). ? Mineral deposit localities grew from 5,123 (pre-Liberation) to nearly 200,000 (today). Of these 200,000 localities, more than three-quarters have verified mineral reserves. ? Minerals extraction and processing contribute to 31 % of the total industrial output value of China (today). ? Regional geological maps at a scale of 1:1,000,000 covering the entire country have been completed, while regional geological and hydrogeological maps at a scale of 1:200,000 covering two-thirds of the country have also been finished (today). ? Before 1949, China was regarded as an oil-poor country. Since the 1950s, China has developed an extensive petrochemical industry. It is largely government-owned except for a limited number of joint ventures. The central government maintains active control over China's most productive fields, including the Daqing field in the Songliao Basin of northeastern China and the Shengli and Liaohe fields in the Bohai Basin of northeastern China. ? Employment in the minerals industry engaged in geological exploration increased from 800 (pre-Liberation) to 1 million (early this decade). The new report provides an overview of the current political and economic situation in China and discusses how this affects the minerals industry. China is in transition between a socialist planned economy and a market economy. This makes it difficult for non-Chinese to keep track of developments. Minerals and Mining in China is divided into 14 chapters that contain detailed statistics, including data on the geographical location and extent of known mineral reserves, production rates, local technical personnel, imports and exports. The report reveals which companies are already active in the area by profiling 50 major investment projects in China's metals and minerals industry. According to its author, China possesses one of the world's largest mining industries, ranking among the leading producers of several metallic and nonmetallic resources. The Chinese mining industry is extraordinarily complex. It has evolved into an overwhelmingly large bureaucracy that was, until the 1980s, shrouded from and misunderstood by the international community. To date, more than 160 types of minerals have been discovered in China. But a significant portion of the minerals and energy base remains largely unidentified and evaluated. And despite China's large reserves of mineral resources, with a population of more than 1.2 billion people, the country ranks among the lowest in the world in terms of proven reserves per capita. In addition, mining recovery rates in China average about 50%, significantly

Jan 1, 1999

By C. H. Smith

The present interest in beryllium seems to be the result of recent developments in the uses for the metal discovery of significant deposits of disseminated beryllium ores, and the development of chemical and physical processing techniques, for recovering the beryllium values contained in these ores. At the present time most of the new and potential uses for beryllium are in the research stage of development and are not consuming large quantities of the metal. However, they do point to an expanding market. Interesting new discoveries or extensions of previously known deposits have been reported during the past year from the Boomer Mine in Colorado, the Mesquite area of Nevada,, the Chemalloy pegmatites in Canada, the Brazilian and African pegmatite districts and from other areas, However, this paper will discuss only four of the beryllium deposits, which appear to be of special significance due to their; large reserves of ore and promise economic development. The new chemical and physical processing techniques are not discussed in detail, but it should be stressed that the development of an economical process to handle the pegmatitic and low-grade non-pegmatitic beryllium ores is of great importance to the development of the beryllium industry. Scientists in both government and industry are co-operating in this effort and it is expected that commercial processes will be developed in the near future.

Jan 1, 1962

By G. R. O?Neil

The justification for a "ligand- selective' approach to fine mineral beneficiation via flocculation is established initially. Special emphasis is placed upon the need to identify non-selective, interfering and complicating adsorption effects. Specific strategies directed towards the design and synthesis of complementary selective flocculants are detailed using a number of different polymers and chelating agents as examples. In this regard, the affinity of polymer-bound ligands for metallic cations, ligand concentration, possible modes of attachment, the application of spaced-out ligands and other considerations in the preparation of selective flocculants are highlighted.

Jan 1, 1983

By Duane B. Jorgensen

The two calcium sulfate minerals, gypsum and anhydrite, occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO, . 2H20) and anhydrite, the anhydrous form (CaSO,) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the larger part of total calcium sulfate resources. Although it has very minor economic use, it is important to the understanding of gypsum deposits and is referred to frequently in the following discussion. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [ ] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have not yet been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. Most gypsum produced ranges from 80 to 95% pure and beneficiation is normally limited to selective mining or quarrying or upgrading by crushing and screening during mill processing. END USES The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris, the hemihydrate of calcium sulfate (CaSO4 ½ H2O), which when mixed with water will set or harden as the calcium sulfate returns to the stable dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uses of uncalcined gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in other countries with building practices different from those in the United States and Canada, relative usage varies widely. Calcium sulfate deposits are the world's largest sulfur resources; minor quantities of gypsum and anhydrite have been used to produce sulfur or sulfur compounds. This use is accompanied by a unique site-specific set of economics because sulfur is generally available from non-gypsum sources at lower cost.

Jan 1, 1994

By John Ralston, Jinming Duan, David R. E. Snoswell, Daniel Fornasiero, Jingwu Yang

The colloidal stability of synthetic silica spheres with clean, methylated and dehydroxylated sur¬faces was studied at different concentrations of dissolved gas and KCl electrolyte at a fixed pH of 4.2. A classic stability ratio/electrolyte concentration analysis shows that hydrophobic, methy¬lated particles undergo faster rates of aggregation with increasing concentrations of dissolved carbon dioxide. Similar data for hydrophilic particles and dehydroxylated particles show no change as a function of dissolved carbon dioxide concentration. Zeta potential data behave simi¬larly, showing a strong influence of dissolved gas only for methylated particles. The results are interpreted in terms of DLVO theory, with the surface-to-surface interaction dominated by the presence of very small protruding bubbles. Direct evidence for the existence of these very small gas bubbles (or "nanobubbles") was obtained using tapping mode atomic force microscopy. Small bubbles do not form on smooth, hydrophilic, or dehydroxylated silicon oxide water sur¬faces immersed in aqueous solutions under known levels of gas supersaturation. Randomly dis¬tributed small bubbles were observed over the whole surface of observation on methylated surfaces of controlled roughness. Bubbles formed on rough, methylated surfaces were larger and less-densely distributed than those on a smooth surface of similar hydrophobicity. The process of bubble coalescence was observed as a function of time. The macroscopic contact angle, measured with respect to the aqueous or gas phase, is very different from the microscopic contact angle detected by TMAFM and appears to be due to the influence of line tension at the pinned three¬phase contact line. The latter has a value of -3 x 10-10 N and acts to stabilize the small bubbles, flattening them and thereby reducing the Laplace pressure.

Jan 1, 2005

By R. Bruce Thorndycraft

Pinson Mining Company was formed to develop a gold orebody located in northern Nevada near Winnemucca. A feasibility study was undertaken in 1979 by a consortium of three Toronto-based mining companies and a Reno-based exploration company. The study indicated a viable project with gold priced above $225 per ounce. A project manager, and mine and mill superintendents, were hired in late 1979 to expedite the development of a 1000 ton per day mine-mill complex. Plant design engineering was contracted with Industrial Design Corporation in Salt Lake City. Three experienced plant metallurgists representing Pinson were stationed in Salt Lake to guide the work of Industrial Design. Among the many design criteria spelled out by Pinson, foremost were bringing the mill on line as quickly as possible at minimum capital cost. Fourteen months after the beginning of design engineering, the completed Pinson mill became operational. Total capital cost, including mine development, was $18 million. The Pinson project has proved to be far more than viable; the entire capital cost will be recovered within 18 months of the mill start-up.

Jan 1, 1982

By John L. Bolles

The mineral processing engineer must have some knowledge of mineral identification, and the greater his knowledge in this field, the greater will be his potential to do his own specialty well. Most metal-bearing ores and industrial minerals require processing of some kind to produce a salable product or a material suitable for further processing. The types of treatment are many, but each one is aimed at separating a mineral or family of minerals from others. Obviously, then, it is basic to all mineral processing to identify the minerals present in the raw material and in intermediate and final products resulting from processing. Very often the mineral processing engineer will enter planning while exploration of a mineral prospect is going on. He will examine hand specimens, drill cores and cuttings, bulk samples, and materials in place. He must identify the valuable minerals, their occurrence and associations with other minerals, and the identity of diluents or host rock. An exact and detailed knowledge of the raw material will usually suggest the treatment processes that should be investigated in the development of the most suitable scheme for that particular raw material in that particular location. Physical properties of a mineral often lead directly to a process for separating that mineral from others. Some well-known examples of these are: magnetic separations for such minerals as magnetite, rutile, ilmenite; gravity separations for gold, silver, galena. cassiterite; flotation separation for most sulfides; distillation of mercury from cinnabar; and selective dissolution in specific solvents such as halite or sylvite in water, gold and silver in cyanide solutions, copper oxides, carbonates, sulfates and silicates in dilute sulfuric acid. These processes and many others are described in detail elsewhere in the Hand¬book and so it is not appropriate to give details here, except to emphasize that processing is aided greatly by complete mineral identi¬fication. Developing a treatment scheme for a new mineral discovery is an exciting assignment fag the mineral processing engineer, but much more of the usual work relates to quality control in existing plants. Here too, mineral identification is important. Some processing is aimed toward producing an end product which will meet exacting specifica¬tions regarding purity or allowable diluents. In this situation it is vital that contaminants be identified so that the process can be adjusted

Jan 1, 1985

By M. Moats, J. Young

Short term laboratory cell electrorefining experiments were performed to examine the impact of electrolyte composition, current density and temperature on deposit structure, roughness, and adhesion to 2B mill finished 316L stainless steel. Copper electrodeposits were produced using synthetic electrolytes with thiourea and the continuous addition of glue. Deposit structures were evaluated using X-ray diffractometry. Surface roughness was measured using profilometry and analyzed using scaling analysis. Finally, an internally developed method was used to measure the force required to remove the electrodeposited copper from stainless steel to determine adhesion strength.

Mar 2, 2022

By B. Ollila, L. Brown

As mining fronts converge in sill pillar extraction, the mine seismic hazard can be significantly altered and large seismic events have been known to occur. This study used common seismological tools to analyze the extraction of highly stressed sills from two deep Canadian mines with the objective of characterizing the rock mass failure process and relation to large seismic events. The approach treated a sill pillar as a mine-scale failure process, meaning the temporal and spatial analysis scales needed to exist on a similar scale to a significant part of the mine. The temporal analysis scale overlapped with the entire mining sequence, included several years of data to establish long term change in the characteristics of rock mass failure. The spatial analysis scale included the rock mass surrounding a large part of the convergent mining sequence. To accommodate the large spatial and temporal scales, the highest magnitude 2% of events in the dataset were analyzed. Similar results were shown for sill pillars in both mines. Changes in event location, time, magnitude, energy index and apparent volume were similar to expected behavior of rock failure. Indications of strain hardening and strain softening were observed in the sills. The hardening period was characterized by a high rate of small events, high energy index and low apparent volume, giving an indication of high stress and low rock yield. The softening phase was characterized by a decrease in the rate of small events concurrent with an increase in the rate of large events, low energy index and high apparent volume, indicative of release of stress and increase in deformation. Large magnitude seismicity was strongly related to the softening phase, with several Nuttli magnitude 3.0+ events occurring shortly after the transition from hardening to softening failure regimes. Sill failure was indicated by consistently low EI and low levels of seismicity and seismic hazard in the sill pillar.

Apr 26, 2022

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991

By D. A. Ellis

This paper review s several new applications of solvent extraction developed in conjunction with a research project carried out under the AEC Raw Materials Division by the Dow Western Division laboratories during the last two years. A process for recovery of uranium from ores by contacting the solid directly with organic solvent without a prior aqueous leach and a process for uranium recovery by contacting thick, unfiltered leach slurry with the solvent were studied in an attempt to simplify ad reduce the cost of ore treatment procedures. Processes to produce pure UF4 products at the concentrate mills thus eliminating the production and subsequent dissolution of the concentrate were investigated. Since many of the leach liquors contained vanadium as well as uranium, solvent extraction processes for by-product vanadium were also studied.

Jan 1, 1958

By John J. Mulligan

Coal is found in every major geographic region throughout Alaska and in two offshore areas. Since about 1852 over 100 small mines have opened and closed. Last years production was almost entirely from one mine in central Alaska. Clearly the utilization of Alaska's abundant coal resources presents political, economic and technical problems that are far from solution. Location and Physical Features Figure one illustrates the geographical and geological similarity between Alaska and western United States. The Arctic region of Alaska generally resembles Wyoming and the Dakotas. The Brooks Range is an extension of the Rocky Mountains. The Central region of Alaska between the Brooks Range and the Alaska Range bears a general resemblance to the basin and range country of western United States. The Southcentral and Southeastern regions has a similar resemblance to the Sierra Nevadas and the west coast of the United States.

Jan 1, 1982

By Carl Heising

Longwall workings in the Federal Republic of Germany are situated in deep depths. Coal deposits are characterized by a sequence of many seams and manifold geological disturbances. Hence result special requirements on the layout of workings, the methods of coal getting, supports, mine ventilation and dust control. As for the application of dust control the large quantities of fresh air and, this, the high air velocity and the limited water contents in the run-of--mine coal must be taken into consideration. The principle of our methods of dust control is to avoid, if at all possible, the development of dust and, if this is not possible, to suppress the dust even during its development. In nearly all coal faces, the method of water infusion prescribed by our Mines Inspectorates is applied. Continuous water in- fusion is preferred. For water infusion in the coal face, intensive developments as to the process and as to the tools and apparates to be applied were done. The German coal mining industry differs between cutting coal getting and stripping coal getting. Water spraying to the tracks of coal ploughs as well as internal and external water feed to the loader required special activities of further development in past years. There are possibilities to still improve such methods in future. A new important field of applying dust control developed from the application of powered supports. In this field, water spraying prevails. Wet methods of dust control are prefered also in the conveying and loading of coal and at through-flow crushers, however, as far as possible, combined with a covering of the working points where dust develops. Devices for the collection and sedimentation of dust, so-called dust exhausters, are used also with crushers In advanced headings, dust control is performed solely by water. Gateroads kept on or behind the coal face line call for new methods of dust control which are at present under development.

Jan 1, 1980

By A. Pinches, R. Winby, P. J. van Staden, M. K. Rhodes, P. C. Miller

This paper is a progress report on the commercialization of using bioleaching for base-metal concentrates. The paper focuses on bioleach processes for recovering copper from chalcopyrite and nickel/cobalt from pentlandite/pyrrhotite. Data is discussed from pilot-plant trials in which an overall recovery >95% was obtained for the bioleaching of copper from chalcopyrite. The pilot plant was operated in closed circuit with solvent extraction and electrowinning circuits for final metal recovery. For the bioleaching of nickel and cobalt from pentlandite/pyrrhotite, an overall recovery of 97% was achieved. Precipitation routines were used to produce a final nickel/cobalt product. The pilot plants were capable of treating a few kilograms of concentrate per day. Prominent features in the design of a 1-t/day (1.1-stpd) copper-bioleach demonstration plant for the treatment of chalcopyrite concentrate are discussed. The plant, which is now under design, will be constructed and operated based on the results obtained from the laboratory pilot-plant campaigns. Issues of scale-up for the demonstration plant, together with integration into upstream and downstream processing, are also addressed. Independently derived capital and operating costs are presented for a possible commercial plant. These cost studies indicate the principle economic issues in considering the application of bioleaching to the extraction of base metals. The benefits of bioleaching complex concentrates that are not amenable to physical beneficiation and economic treatment by conventional smelting are highlighted. Issues, such as the environmental aspects, that illustrate the benefits of bioleach technology are given.

Jan 1, 2000

By D. J. Fitzpatrick

The paper reviews current mining subsidence research at The Department of Mining Engineering, University of Notting- ham. Special attention is being devoted to prediction of ground movements between the mining horizon and the surface using physical and computer-based models. The paper presented discusses linear and non- linear finite element methods and compares results with those from physical models and field observations. Special attention is focussed on the determination of the effect of caved zones on overlying and underlying geological structures. The paper presents data from comparisons with U.K. case histories.

Jan 1, 1986

By J. M. Richardson, A. L. Mular

Metallurgical balances are fundamental to the successful design and operation of concentration and dewatering circuits. With computerized balance techniques gaining prominence in recent years, it is essential that engineers understand the basic principles that underlie the new methods, as well as the various applications for design of new plants and analysis of existing operations. This chapter discusses two important types of metallurgical balance: (1) steady-state design (2) operating data adjustment Application of computerized steady- state design balancing is demonstrated through the example of a typical copper concentrator flowsheet. Operating data adjustment to achieve a consistent balance is demonstrated for a typical concentrator operation.

Jan 1, 1986