Search Documents

By James J. Scott

In the fall of 1976 the author started test work with Friction Rock Stabilizers in uranium mines of the West, principally in the Ambrosia Lake and Churchrock districts of New Mexico. Tests were also conducted in other uranium mines in the Rocky Mountains area. These mines are plagues with problems in ground control due to the weak formations in which mineralization occurs, mudstones, siltstones, weak sand, etc. For this reason, it is extremely difficult to obtain good anchorage for long periods of time with conventional mechanical roof bolts. Resin bolts give good anchorage but are expensive and, because of hole erosion and difficulties in installation due to inadequate equipment for mixing the resin and placing the rebar, they are not widely used. Field testing was also carried out in trona, limestones and hard and soft shale formations. The mechanism of the Friction Rock Stabi1izer support is discussed and pull test data presented for various rock types.

Jan 1, 1977

By C. E. Jordan

The U.S. Bureau of Mines investigated flotation hydrodynamics to improve the recovery of coarse phosphate. Fluid velocity profile measurements were used to characterize the hydrodynamics within commercial phosphate flotation cells and laboratory flotation cells. The effects of agitation, aeration, and pH on coarse phosphate recovery were measured in the laboratory flotation cells and correlated with the hydrodynamics measurements. Test results revealed that the agitation energy and aeration level had a significant effect upon flotation response. By optimizing these two parameters, 92 pct of the phosphate was recovered in a rougher flotation concentrate grading 28 pct P2O5?

Jan 1, 1994

By Tracy E. Chantson, Brian R. Green, Kenneth G. Ashurst

Work that has culminated in the manufacture and testing of a old-selective resin on a pilot-plant scale is dcscribed. Following a brief discussion about the nature of commercially available resins which identifies them as poor candidates for a gold extraction application, the improved properties of the new type of resin are illustrated using results from comparative loading tests. Further results from continuous countercurrent extractions using synthetic leach liquors and elution work using thiourea as the eluant demonstrate the superiority of the new resin over commercial resins and hence, its potential for use in a resin-in-pulp process for gold.

Jan 1, 1989

By D. C. Hatch

At the MacIntyre Development of the Titanium Division of National Lead Company a magnetite-ilmenite ore together with gabbro-anorthosite waste is mined from an open pit by shovels and trucks. The ore from the pits is trucked to ore stockpiles for blending ahead of the crusher and to free the mine from crusher delivery schedules. The ore stockpiles are blended to yield a 16.5 to 17.0 % TiO, crusher feed. This requires mining on an assay cut-off rather than a visual grade cut-off. Highly mineralized ore runs from 20 plus % TiO2 and 30 plus % Fe to 15 % TiO2 and 40 plus % Fe as the ratio of ilmenite to magnetite changes. There are three major ore types in the present pit with magnetite ratios varying from about one to one up to three times as much magnetite as ilmenite. Ilmenite and magnetite together liberate from gangue down to about 10 mesh and this is the basis of the magnetic cobbing. Below 10 mesh the ilmenite and magnetite start to separate and ore cobbing pulleys will not hold the ilmenite.

Jan 1, 1968

By Edward J. Harvey

Joplin, one of the most famous zinc mining camps of a bygone era, is today experiencing a healthy growth in manufacturing enterprises. Manufacturing requires water, and knowledge of its availability and quality often is the main factor in location of industry. For this reason in January 1964, on the suggestion of the former State Geologist, Dr. Thomas R. Beveridge, a study of the water resources of the Joplin District was undertaken as a cooperative effort of the Missouri Geological Survey and Water Resources now under the direction of Dr. William C. Hayes and the U. S. Geological Survey. The project area is in southwestern Missouri on the Springfield Plateau and is bordered on the west and north by the Osage Plains of Kansas and Western Missouri, (fig. l). Upland altitudes rise from 900 feet above sea level in the west to 1400 feet in the east. The countryside is rolling to moderately hilly and much is excellent farmland.

Jan 1, 1965

By E. I. Jurgens, K. E. Hanney, D. C. Comrie, R. H. Fletcher

Introduction The reclamation of mine/mill tailings areas is undertaken for a variety of objectives including safety, appearance, economical use of lands and forests and long term storage of a future resource. The establishing of criteria for these objectives at any site is a shared task of the government and mining company. Our attention in this paper is directed to uranium mine/ mill tailings as they are handled in the Canadian industry and in the unique Canadian climate. We focus our attention on the state of the art. Uranium is a ubiquitous mineral forming an average of 4 g per tonne of the Earth's crust. Ores are mined at about 500 g per tonne so that the residual content of uranium in tailings is comparable to average background levels. However, as in most mine/mill operations, the ore contains other minerals that become readily mobile after milling operations. Thus the main objective of tailings impoundment is the stability both physically and chemically of the mobile materials. Since the requirements for the operation and construction of tailings areas in Canada have changed considerably over the past decade, there exists a great many mine/mill tailings areas which while considered adequate in their day, would not meet modern criteria. However, most of these installations pose no concern or hazard to the public. The proximity of mine/mill development to inhabited land areas has necessitated more stringent modes of tailings operations and provisions for tailings site reclamation. The more important of these have been: 1) the prevention of dyke failure, with large liquid-solid outflows onto adjoining lands, and 2) the prevention of seepage from the tails of pollutants such as chlorides, sulphides, heavy metals and radionuclides. Uranium mill tailings are discharged as a slurry from the concentrator after the removal of generally only about 1000 g, or less, per tonne of uranium from the as-mined ore. As a consequence, a great volume of low level activity waste is generated. The amount of tailings is expected to grow in quantity in the future even faster than the increase in yellowcake production, as the demand for energy

Jan 1, 1980

By R. A. Matuszak

U.S. Government sponsored studies proclaim large reductions in surface mine productivity. Consulting studies place a large share of the blame on increased governmental regulatory activities and on inexperienced, improperly train people. Union rules, which allow indescriminate bidding for job openings, seem to be a major factor causing the lack of experience in spite of elaborate training programs.

Jan 1, 1982

By M. M. Botz

Cyanidation tailings which are disposed in a surface impoundment experience a loss of cyanide due to natural degradation, frequently reducing the cyanide concentration to very low levels. Quantifying cyanide losses in terms of pond geometry, local weather conditions and feed solution chemistry has been largely empirical though in many cases mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or an effluent limitation. To permit a more quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, WAD and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared against data collected for a North American tailings impoundment during 1998.

Jan 1, 1999

By Rudolf Fahn

Bentonites are best suited for the preparation of acid activated clays with efficient adsorption properties. They are weathering products of acid volcanic ashes and their natural deposits are world-wide spread. The main constituent of bentonite is the aluminium hydrosilicate nontmorillonite with a high ability to swell. Süd-Chemie owns bentonite deposits in Germany and subsidiaries in Italy, Mexico and Arizona.

Jan 1, 1979

By E. T. Pecina

Bioleaching is a viable option for the processing of auriargentiferous refractory ores with high arsenic content. The application of mesophilic (A. ferrooxidans and ?L. ferrooxidans?) and thermophilic bacteria of the genus Sulfolobus (S. solfataricus and S. acidocaldarius) as oxidant treatment before the cyanidation of an industrial arsenical pyrite concentrate is presented. The results show that extraction of gold and silver increases due to bio-oxidation caused by mesophilic bacteria and results in a maximum gold recovery of 68%. In all strains studied, biooxidation resulted in an average silver recovery of 50%. The results showed that all evaluated strains were sensitive to solids content (5 to 20%) and average particle size (75 and 38 µm) of the concentrate.

Jan 1, 2010

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980

By William A. Vogely, DeVerle P. Harris

INTRODUCTION Perspective The phrase "minerala resource appraisal" is widely and loosely used to refer to any quantitative description of a naturally occurring source of fuels, metals, or nonmetals. This leads to confusion when mineral resources are so conceived, for the term refers generically to information on stocks-mineral endowment, resources, reserves, and potential supply-that differ in ways that are important in economic analysis. Mineral resource and other stock measures- these are not flows, e.g., the supply of minerals-have precise technical meanings, which are presented in this paper. Quotation marks are used to separate the nontechnical use of mineral resource from the technical. The term appraisal also leads to some con- fusion because it too is loosely used. When an appraisal employs probability and statistical methods, the appropriate term is estimationb, not appraisal or assessment. This paper presents a conceptual framework or mineral resource information which renders technical, or well defined, relationships of mineral endowment to physical attributes of the earth's crust and earth processes, as distinct from economic values, and identifies estimation approaches that lead to different economic measures of stocks and flows. An important result of this approach is the distinction between the relevance of mineral resource information to economic and policy issues about potential sup- ply (stocks) and dynamic supply (flows across time). With regard to policy analysis, this paper recognizes that mineral resource information has a cost as well as an imputed value. Such a treatment implies that there is an optimum state of resource ignorance, or enlightenment, for a given policy issue and that the relevant economic issue is the selection of that information strategy and appraisal methodology that is indicated by the optimum state. Until the initiation of the OPEC oil embargo, the demand for information on mineral re- sources and potential supply was limited to occasional studies commissioned by Congress or the President of the United States. In these, mineral and energy resources remained loosely de- scribed. When quantitative estimates were supplied, they were not rigorously made, and the estimates and the methodology accordingly escaped close scrutiny. Usually, neither the geo- logical nor economic bases for estimation were carefully described or critically examined. The imposition by OPEC nations of the embargo on oil caused a sudden change in the public and scientific demands for specific 'resource" appraisals, especially of oil and of uranium. These

Jan 1, 1985

By Samuel S. Adams

Economic concentrations of potassium are essentially limited to thick, stratigraphic sections of marine evaporites. These deposits were precipitated through the evaporation of sea water in restricted epicontinental seas or in grabens related to continental margin rift systems. Following deposition the deposits were subjected to diagenesis and varying degrees of metasomatism and structural deformation. The origin and characteristics of potash deposits are easier to study and interpret than those of most ore deposits because the phase chemistry of the salt systems is known and the approximate composition of the ore-forming fluid (sea water) can be inferred with confidence. It is particularly helpful that the temperature and pressure of deposition approximated that of present earth surface conditions and the pertinent mineral assemblages can readily be duplicated in the laboratory. The study of these comparatively simple salt deposits provides examples of the practical advantages of understanding the genesis of an ore deposit. These observations, in turn, illustrate the importance of pursuing research on the more complicated magmatic, hydrothermal, and ground-water systems as a means to the more successful exploration for and exploitation of the deposits they have produced. It is the purpose of this paper, therefore, to discuss certain aspects of salt deposit geology as they contribute to exploration and mining through some understanding of ore formation. References to field examples and chemical relations in the salt systems are brief. All examples are more fully discussed, however, in the references cited.

Jan 1, 1970

By Gennaro Gerald Marino

In this paper the main subsidence- ground-structure interactions and an overview of the response of surface structures to subsidence ground movements are presented. The purpose of the paper is to augment our understanding for more effective application of available data as well as to highlight the essential site conditions in building response. The data presented general1 y applies to houses to structures up to 2-3 stories high and no more than several hundred feet in length. Superstructures of these buildings are supported by exterior (wood-frame or masonry) bearing walls with the interior floor loads carried by essentially one row of interior columns. This paper is not directed towards the response of tall buildings, steel-framed structures, or building types commonly associated with schools, churches, libraries, etc.

Jan 1, 1986

By L. D. Hartzog

A pilot plant investigation of a semi-autogenous mill - ball mill circuit is described. The plant was operated with minus eight-inch diabase as feed material to the semi-autogenous mill. The semi-autogenous mill recycle screen underflow was put to a ball mill in closed circuit with a cyclone. An operating Work Index of 13.3 to 14.9 was obtained with the pilot ball mill. This Index is substantially in agreement with the scalped feed laboratory Work Index for 15.3 for recycle screen underflow. The Bond Index of the diabase was 15.8. Thus, one may use the scalped feed laboratory Work Index to size semi-autogenous grinding plant ball mills.

Jan 1, 1974

By V. T. McLemore

Rare earth elements (REE) are becoming more important in our society. REE deposits are found throughout NM. Some REE past production (1950s), as bastnaesite, came from the Gallinas Mountains district, Lincoln County, NM. Several companies and the U.S. Bureau of Mines (USBM) have conducted exploration programs to identify REE potential. Four types of deposits are found in the district: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipe and iron skarn deposits; all are associated with Tertiary peraluminous, alkaline to alkalic-calcic volcanic rocks. District zonation is defined by base metals (REE-F-Cu veins) that form center of the district, surrounded by REE-F veins. The magmatic-hydrothermal breccia pipe deposits form a belt partially surrounding the veins. Iron skarns formed at the top and edge of the trachyte intrusion and are likely the earliest stage of mineralization. In 1991-1992, USBM calculated an inferred resource of 0.487 million metric tons with a grade of 2.95% total REE. With the projected increase in demand of REE, areas such as the Gallinas Mountains district in New Mexico are being re-examined for additional REE potential.

Jan 1, 2011

By E. L. Michaels

Laboratory and pilot scale tests have been made to deter- mine the utility of heavy media separation, particularly a cone type separator, as a means of recovering aluminum from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy media system was deter- mined. Two-stage pilot scale heavy media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses were determined. The experimental results indicate that with certain reservations a heavy media cone system can be utilized for aluminum separation and recovery from shredded and air classified municipal solid waste. Observations made using two-stage heavy media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1974

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By James W. Mahar

The following paper summarizes our observations on building response to mine subsidence and techniques for mitigation of building damage. The subsidence cases are located in Illinois. The general description of the geologic and mine conditions are primarily for those sites. Data on building response and mitigation measures were collected under grants supported by the Abandoned Mined Lands Reclamation Council (AMLRC) of Illinois and the U. S. Bureau of Mines, in Twin Cities, Minnesota. Case histories include pit and sag subsidence primarily beneath abandoned room and pillar mines. The majority of the paper deals with structures affected by sag subsidence. Most of the structures are one and two story homes. The first section of the paper summarizes the typical geologic and mining conditions at the sites. Building response to pit and sag subsidence follows the first section. Emphasis is placed on the behavior of concrete and masonry foundations, and wood frame and masonry superstructures. The third section describes mitigation techniques used to prevent or minimize building damage. A summary of the observations and critical parameters is given at the end of the paper.

Jan 1, 1982

By Hamid Maleki

Mine seismicity is influenced by the mechanical properties of both near-seam strata and overburden/underburden and the prudent selection of mining methods and mine layout designs, utilizing sitespecific structural setting of the mines. The importance of adequate data collection, monitoring, and prudent structural designs has long been recognized and utilized in many U.S. operations with adequate engineering resources. In this paper, two case studies of historic seismic events and contributing factors, in deep coal and trona mines with overburden thickness exceeding 1,500 ft, are reviewed using observations and analysis. By back analyzing the overburden response in a historic room-and-pillar coal mine, the overburden collapse mechanism associated with a 3.3 magnitude seismic event is reviewed as well as the need for improvements in designs including panel and barrier pillar widths. Similar high-order seismic events were also experienced in trona mines of the Green River Basin during 1990s, interrupting room-and-pillar mining and creating ground control concerns. Efforts to improve structural mine designs are described in this paper leading to stable and productive operations for decades following the high-order seismic events in both coal and trona case studies. These efforts included improving room-and-pillar extraction layouts and utilizing properly designed longwall mining techniques that were verified using long-term geotechnical instrumentation. The study mines are located on the Wasatch Plateau (WP), Utah and in the Green River Basin (GRB), Wyoming. More recently, in Utah’s East Mountain alone, Energy West Mining Company (EWMC) has extracted some 165 million tons of coal without any significant incidents. Overall, favorable geologic conditions and prudent mine layout designs are key elements to this successful experience in both single- and two-seam layouts. Utilization of conservatively designed longwall mining technique in the GRB has been geotechnically stable, using reported experience in 15 panels and monitoring results in the Northwest (NW) District with measurable longwallinduced seismicity being rare. These studies demonstrate a considerable amount of progress that has been made within the last four decades in the application of longwall mining technique, integrated monitoring, and analyses for the verification of structural designs in mines in the United States.

Jul 1, 2023