Search Documents

By Yoginder P. Chugh

The term "fatigue" in mechanics, is used to refer to reduction in the strength of a material subjected to fluctuating or alternating stresses. Stresses that vary with time are called fluctuating stresses and if during fluctuation the stresses also change sign, they are called alternating stresses. In the field of rock mechanics, the term fatigue (static fatigue) has often been misused to refer to failure of geologic materials in time domain under constant load. To avoid confusion, we use the ten cyclic fatigue here to refer to failure of rock under alternating or fluctuating stresses. Fatigue in metals has been studied for over 100 years. Fatigue properties of geologic materials have, however, received little attention in the past. This is probably because until recently very little was known in regard to the behavior of geologic materials even under static loading. Secondly, suitable equipment for conducting cyclic fatigue experiments was not available until quite recently. A few cyclic fatigue studies have been undertaken on geologic materials to relate it to percussive or rotary drilling mechanisms (e. g. Grover et a11*; Burdine2). The results of these studies were inconclusive due to limited effort. Cyclic fatigue in concrete has been studied more extensively than geologic materials (e.g. Nordby3, Gray et al 4 and Bennett et a15) and mechanisms of fatigue in concrete are better understood than in geologic materials.

Jan 1, 1975

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata, Dohta Awaji

"The immediate ring closure method, in which the entire periphery of the excavation area is closed immediately with an initial support within a short distance from the excavation face, has been increasingly used in Japan, especially, as one of the most effective countermeasures against difficult ground conditions in conventional tunneling. For reasonable design of this method, the performance requirements for the initial support should be clearly stated. The analysis of construction data of 30 road tunnels and the three-dimensional numerical modeling based on real data suggest that the immediate ring closure stabilizes the tunnel structure and the ground around it because of the inner pressure effect of the initial support, especially, for low ground competence factor and small internal friction angle. Finally, the bending compressive strength and the cross-sectional geometry of the initial support have to be considered in the tunnel design while considering the earth pressure and ground properties. INTRODUCTION Conventional tunneling methods often deal with difficult ground conditions such as soft ground or squeezing ground conditions. The immediate ring closure method, in which the entire periphery of the excavation area is immediately supported within a short distance from the excavation face (Figure 1), has been increasingly used in Japan as one of the most effective countermeasures against difficult ground conditions in conventional tunneling (e.g. Takahashi et al., 2011; Nakaoka et al., 2013). The immediate ring closure method was empirically identified as effective for reducing ground surface subsidence and tunnel deformation. However, the working effects of the method have not been clarified sufficiently. To improve the design of this method, the working effects of this method and the performance requirements for the initial support need to be clarified. The relation between the effect of immediate ring closure and earth cover has been clarified (Mashimo et al., 2008; Awaji et al., 2013),"

Jan 1, 2016

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength. Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics. The analysis suggests grinding depends mainly on the state of aggregation of the ground products in- side the mill and the pulp fluidity. Implications of the observed effects on ultrafine grinding in general are discussed.

Jan 1, 1983

By Richard H. Sillitoe

Gold is an important byproduct and, locally, coproduct of porphyry copper deposits, and possesses potential for discovery as the major metal in porphyry deposits in either island arcs or Cordilleran belts. Tungsten and tin occur as major components of several potentially bulk-minable porphyry deposits, as well as being byproducts from the Climax porphyry molybdenum deposit. Whereas porphyry tin systems are localized in Cordilleran back-arc settings, their tungsten counterparts appear to span a range of geotectonic settings, from Cordilleran principal arcs through back-arcs to rifts. Although silver is a common byproduct of porphyry copper deposits, it tends to be preferentially concentrated with lead and zinc on the fringes of all types of porphyry deposits and/or as late-stage superpositions; the latter situation could be of some interest in the higher parts of porphyry systems. As byproducts, rhenium, uranium, platinoids and magnetite are exploited occasionally, and rutile and the rare metals, such as tantalum and niobium, have merited consideration.

Jan 1, 1982

By Richard O. Y. Breese

Geologically and commercially, the term diatomite is applied to the nearly pure sedimentarv accumulation of diatom frustules- the microscopic skeletons of unicellular aquatic algae belonging to the class of golden brown algae, bacillariophyceae. The sediments are fine-grained, siliceous, and consist primarily of amorphous opaline silica with only minor amounts of organic residue, secondary minerals, and co-deposited non-diatomaceous or crystalline clastic debris. In the geological sense, the name diatomite implies sedimentary accumulations that have reached appreciable thickness and when thick enough, such accumulations consequently may have possible commercial potential. Although the term diatomite is popularly and inappropriately applied to any sediment in which there is an abundance of diatom frustules, alternative terminology is more correctly employed to describe the less pure diatomaceous sediments, for example: clay-bearing diatomite or diatom-bearing clay. Synonyms in current usage include diatomaceous earth and kieselghur. More antiquated and obsolete terminology includes tripoli-powder, tripolite, and infusorial earth. Worldwide, diatomites occur within Tertiary to Recent lacus- trine and marine sedimentary facies. Although diatomite is wide- spread throughout the world, deposits that contain high purity, commercially versatile ore are uncommon. Physical properties of the diatom and of processed diatomite that provide unique commercial value in a broad spectrum of market end-uses include ornate fine structure, low bulk density, and high porosity and surface area. Properties of equal importance are mild abrasiveness, high absorptive capacity, insulating ability, relative inertness, and high brightness. End-use markets are diverse and range from insulating brick and absorbents through quality sensitive filter aids and premium quality functional fillers. Notwithstanding both the economic attractiveness of the specialty markets and the commercial versatility of the high purity deposits, deposits of lesser purity are mined in nearly all parts of the world for less demanding uses. Mining costs are minimized through open pit quarrying, but in Europe, Asia, Africa, and South America underground mining methods are also employed. Blasting is not required because diatomite is soft and easily broken loose with mechanized equipment. Following gentle crushing, the ore is dried, milled, and processed into one of three broad categories of products: naturally milled, straight calcined, and flux calcined grades. Each of these principal categories is further subdivided into additional grades through particle size adjustment of the powders. Agglomeration of particles, alteration of fine structure, and color change are achieved through calcination. Flux calcination further accentuates these changes. Production throughout the world is dominated by the United States, followed by Romania, the former Soviet republics, and France. Other major producers include Spain, Mexico, Iceland, Korea, Japan, and Germany. Denmark is a major producer of Moler earth products, which consist of a diatomite-clay mixture. HISTORICAL BACKGROUND The first industrial use of diatomite can be traced back some 2000 years to the Greeks and to the use of diatomaceous earth as a component in lightweight building brick and in ceramic pottery. It was not until the mid-1800s, however, that the unique properties of diatomite were first recognized and the market end-uses explored and developed. One of the most important of the early uses followed the development of dynamite by Alfred Nobel in the mid-1860s, whereupon diatomite was used as a component of the explosive to improve stability and safety. Other early uses included low temperature insulating and refractory bricks and as a component in insulating and fireproofing construction panels. During the 1920s, processing technology underwent a very rapid evolution with the development of calcination, flux calcination, and air classification technologies. Through these technologies, innumerable different size and grade classifications could be made for market applications and for rapidly diversified end- uses. Today, the application of processed diatomite for filter aid is the largest of the quality sensitive end-uses. Specific filtration uses include the clarification of beer, wine and liquor, vegetable oil, syrup and sugar, pharmaceuticals, and swimming pool water, to name a few. As a functional filler and extender, processed diatomite is ideally suited for application in paint, rubber, and plastic formulations. Other filler applications include use as an anti-blocking agent in plastic film, anti-caking agent for fertilizer, thermal insulating material, catalyst carrier, polish, abrasive, pesticide and fertilizer carrier, and chromatographic supports. Throughout much of the world diatomite is still used as a component of insulating brick and as an absorbent.

Jan 1, 1994

By L. Adler

To properly analyze and apply mining equipment, a systematic, current, inclusive, and simple classification scheme is required. This paper provides such a classification for Roadheaders. This Roadheader classification is based on factors, such as the rock cutterhead, the boom type, and the chassis configuration. It first assigns Roadheaders as an equipment type within the larger group of Integrated Excavators. The Roadheader type is then delineated into the following subtypes: the standard, the extended boom, the tunnelers, and the miscellaneous. Next, these subtypes are devolved into kinds, and finally variants and attachments are considered. To resolve inconsistencies in characterizing the Roadheader, cross-referencing is employed within the classification scheme.

Jan 1, 1996

By B. Listerud, G. Zhan, M. A. Jones

Barrick Goldstrike Mines Inc. (BGMI) operates the Betze-Post openpit and the Meikle and Rodeo underground mines. Because the majority of the orebody is located below the water table, mining at BGMI requires a significant dewatering program. BGMI has a comprehensive dewatering and water management system that experienced a peak dewatering rate of 4,400 L/s in the mid 1990s. Changes to the hydrologic/hydrogeologic system caused by the mine dewatering have been monitored by an extensive network of groundwater monitoring wells and surface water monitoring stations, which cover about 1,550 km2. In addition to the monitoring program, a new tool, called Interferometric Synthetic Aperture Radar (InSAR), has also been used to enhance the evaluation of changes. Finally, a groundwater flow model has been developed that successfully simulates and predicts aquifer responses in the mine area and region. The well-calibrated flow model has served as a reliable tool to develop dewatering and mining plans, and project post-closure hydrologic conditions in the region. This paper introduces the BGMI dewatering and water management system and the means used by BGMI to evaluate and anticipate hydrologic responses in the region. The water management and analysis system has been and continues to be an integral part of managing ongoing operations, planning and pricing out future activities and evaluating the long-term effects of mine water handling.

Jan 1, 2011

By J. G. Pippenger

The Coteau Properties Company's Freedom Mine is a surface lignite mining operation utilizing large draglines, trucks and shovels, tractor-scrapers, and bulldozers to uncover a single coal seam. In 1989, a work order system was instituted to record data by equipment type, cost, productivity, and distance, and to provide historical information for planning the most efficient and economic use of each equipment type in the mining operation. This report explains how the work order system was initiated, what data is tracked, and how the data is utilized for equipment and project scheduling.

Jan 1, 1994

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a man- made force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by Mine Safety and Health Ad- ministration (MSHA), as well as the various state departments of mines.

Jan 1, 1981

By W. Robert Power

Stone is considered by many to be the premium material for beauty and durability in all kinds of construction. Its use dates to the dawn of civilization and only buildings made of stone have survived from ancient times. The use of stone relative to other materials declined from the beginning of the present century reaching a low point in the third quarter, but there has been a resurgence in the use of stone in construction during the past decade, due probably, to new techniques for producing stone, a greater recognition of its beauty and durability, and greater affluence among consumers. The aesthetic appeal of stone is attested to by the many attempts to simulate it in synthetic materials. Today, natural stone is considered by many to be the ultimate in aesthetic appeal, durability, and ease of maintenance. Consumption of dimension stone has increased dramatically during the past decade. The US Bureau of Mines reported that the total value of US consumption in 1978 was $1 13 million and that total imports were valued at $65 million in 1979 (Anon., 1980). In 1989 consumption of domestic dimension stone was valued at $208.3 million and imports at $525 million. This dramatic increase occurred after demand had decreased at an average rate of 2.5% in the two decades prior to 1978 (Anon., 1980). More than half of the imports come from Italy, but production of dimension stone has increased worldwide spectacularly. Meaningful statistics on dimension stone are hard to acquire. The finished piece of stone is a highly value-added product, but stone may be sold as rough blocks, sawed slabs, or finished product. The same piece of stone may therefore be sold and reported three or more times. Furthermore, although the quantity of stone is most commonly reported in tons, stone cladding is more often sold by the surface area and at the same price for different thicknesses. By any measure, however, the production and consumption of dimension stone has increased dramatically during the past decade. A significant indication of the resurgence of stone was the introduction of two new trade publications during the 1980s. Stone World (Tradelink Publishing Co., Inc., Oradell, NJ), introduced in 1984 is published monthly and Dimensional Stone (Dimensional Stone Institute, Inc., Woodland Hills, CA), introduced in 1985 is published monthly. Both magazines provide useful information on new technology, market trends, producing areas and companies, and other information not previously available.

Jan 1, 1994

By P. J. Stewart, S. Tracy

This presentation describes the operation and features of the WCC Carbon Reactivation Kiln. Particular emphasis is placed on minimizing carbon losses, corrosion resistance, fuel efficiency and the fate of mercury during reactivation in the multiple-tube vertical retort. Detailed laboratory work indicates that there is complete vaporization of mercury in the kiln, no refluxing in the upper sections and distinct advantages in using this type of kiln when sizing collection equipment.

Jan 1, 1993

By M. Akser, F. L. Pirkle, B. W. Stratford, B. Ipekoglu

To date, no ilmenite, rutile and zircon deposits of commercial importance have been reported in Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit in the vicinity of Ormanli, which is located northwest of Istanbul along Turkey's Black Sea Coast. Consequently, beach coil sand-dune samples were collected from that area for additional analysis. Laboratory methodologies drat were designed to simulate standard industrial heavy-mineral plant practices were used to analyze and evaluate the samples. Based on these analyses and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1997

By Winfield G. Wright, Greg P. Meeker, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

A really extensive acid sulfate-altered and mineralized rock in the southeast Red Mountains area is noted for its association with naturally occurring and mine-related acidic and metal-rich waters. Integrated geologic and aqueous geochemical studies demonstrate that the degree of metal mobilization and acid production in natural waters correlates well with the type of hydrothermally altered rock and structural features in which these water interact. Quartz-sericite-pyrite, quartz-alunite, and argillic alteration assemblages are associated with some of the most naturally acidic, high-metal waters in the study area; calcite-bearing propylitic rocks are related to the most pristine waters and buffer sulfate-rich, acidic waters produced by pyrite oxidation. Trace metals in natural waters are mostly derived from enargite, zinc-rich tetrahedrite and sphalerite. Pyrite oxidation contributes very little with respect to base-metals in these natural waters.

Jan 1, 2000

By G. Thorsen

An alternative way to the normal practice of precipitation of jarosite, goethite, or hematite for removal of iron from zinc sulphate process liquors/ is to employ the techniques of solvent extraction. The process presented avoids the addition of any external alkali for the extraction of iron by integrating the leaching and solvent extraction steps in a hydrometallurgical zinc plant. By starting the leaching of zinc from the solid zinc calcine material with an organic solution of an acid liquid cation exchanger, the organic phase is loaded with the organic zinc salt from the direct reaction with zinc oxide. The residue from the organic leaching is transferred to a hot acid leach circuit where the remaining zinc oxide and the zinc ferrites will dissolve form¬ing an aqueous sulphate solution of zinc and iron. In the subsequent solvent extraction of iron from this aqueous leach solution, iron is exchanged with zinc from the organic phase. The commercial carboxylic acid Versatic 10 (Shell) is highly efficient for this integrated process of leaching and solvent extraction. The resulting iron-loaded organic phase is heated to 150-200 C in the presence of water whereby the iron will be directly precipitated from the organic phase as iron oxide of high purity and the regenerated organic acid is recycled to the organic leaching step for reloading with zinc.

Jan 1, 1980

By Richard Klimpel

A common problem in mineral processing and chemical engineering is the need to estimate flow rates and/or weight ratios involved with engineering operations for which it is inherently difficult to directly measure stream weights. Simple examples of this situation include stream separators (a classifier operating on a particle flow) and stream mixers (the mixing of new feed and circulating load in a ball mill circuit). Often in these types of operations, it is possible to sample the streams involved to get approximate component analyses (e.g. size distributions of solid streams, chemical composition of chemical streams). In this paper various formulae are developed which can be used to estimate stream flow rates or weight ratios given information on the stream components. The type and level of experimental error present in the stream component analyses does have an important bearing on the numerical values (and reliability) of the weight ratios calculated by the various formulae. A simple but theoretically sound method is shown for selecting appropriate estimation formulae for any given engineering operation. The derived formulae are applied to sets of experimental classification data for illustration purposes.

Jan 1, 1979

By M. Fig, A. Juganda, M. Zurhorst, J. Brune, C. Strebinger, G. Bogin

"Understanding the airflow patterns in and around the longwall panel can help to identify poorly ventilated areas that may be prone to methane accumulation. Ventilation network modeling provides quick simulation time, and flexibility in adjusting airway parameters and ventilation controls. Such modeling is effective for analyzing linear ventilation networks in underground mines, but cannot compute flows in caved areas of hard rock mines or longwall gobs. The use of Computational Fluid Dynamics (CFD) enables a more detailed investigation of the interaction between the airflows in these caved areas but requires much longer computational times, designing complex meshes and determination of a variety of modeling parameters. Airway friction factors and ventilation controls are simple to implement in a network model but can be difficult to model and adjust in CFD. This paper will focus on using mine ventilation network simulation to identify and analyze key parameters that are affecting airflow distribution in and around the longwall panels, prior to more detailed analysis with CFD modeling, using the example of a longwall coal mine. INTRODUCTION In longwall coal mine ventilation systems common in the U.S., the main purpose of bleeder ventilation is to dilute methane gas and prevent the formation of explosive gas mixtures in the caved, poorly ventilated gob areas and adjacent mine workings. In longwall operation, these critical areas include the development headings inby the longwall face, and the gob. Methane-air explosions in these areas may be ignited by spontaneous combustion, rock-on-rock friction and other sources. Although rare, ignitions due to rock-on-rock friction caused by roof falls caving into the longwall gob are possible and were suspected in the Willow Creek mine explosions in 1998 and 2000 (Elkins et al., 2001; McKinney et al., 2001). Rock-on-rock frictional ignitions are difficult to prevent, as they occur in inaccessible areas. Therefore, rendering the gob area inert is essential to prevent the formation of explosive mixtures. Research by Gilmore et al. (2015) and Brune et al. (2015) has shown that gob inertization can be a difficult or impossible when using bleeder systems, since the flow of gases through the gob depends on the gob permeability and the amount of fresh air leaking from the face and the immediate roof caving conditions cannot be controlled by the mine operator. Having the ability to predict the location where explosive gas zones (EGZs) form inside the gob will be helpful for designing the best ventilation setup to minimize explosion and fire risks."

Jan 1, 2018

By Slobodan Vujic

Production of building materials such as are stones, sand, gravel etc., is characterized by a relatively low economic value and requires reasonable transport costs. That is why we are often faced, in our practical work, with the fact that within the framework of a relatively small area several open pits of building materials are, developed side by side while neither ecological, urban and spatial nor location factors have been taken into consideration. Numerous locations together with heterogeneous factors. point undoubtedly to the problem of planning the open pits locations for building mateials as a very serious and complex one. Even when certain localities are in question, it is rather a difficult task to present a real state and encompass all the, important location factors by mathematical model ling. This paper presents one of such models for solving the problem of selecting a location for building materials open pit.

Jan 1, 1992

By G. Schriever, H. Thiel, E. J. Foell

A long-term, large-scale, disturbance-recolonization experiment with relevance to the environmental effects of deep seabed mining is described. The study is funded by the German government and was launched in the abyssal eastern tropical South Pacific Ocean in February-March, 1989. After obtaining pre-impact baseline environmental data, a 10.8 km2 (4.2 sq miles) circular area of seafloor was disturbed using a specially designed "plow-harrow" device. An initial post-impact sampling series was carried out immediately after disturbance followed by a second post-impact sampling series six months after the disturbance. Plans call for repeated visits to the site at two year intervals to monitor the anticipated slow recolonization process until the area is inhabited by a new, stabilized community.

Jan 1, 1993

By P. Somasundaran, S. E. El-Mofty

A comparison of the IMC Anionic Process and the CLDRI Process, based on pilot plant testing of waste pebble by Jacobs Engineering is presented. Estimated costs for constructing and operating a beneficiation plant utilizing dolomite flotation are given. Research to develop practical flotation processes for removing dolomite from low-grade phosphate rock has been a high priority for the Florida Institute of Phosphate Research. The Institute funded the above pilot plant programs in 1998 and 2000. The Florida Phosphate industry currently deals with the increasing dolomite content of ore reserves by practicing selective mining. Heavy media separation plants installed at two mines to remove dolomite from pebble are not being operated. The flotation separation of dolomite from waste pebble requires that the flotation feed be ground. Grinding liberates the mineral species and produces particle sizes small enough to be floated. Only two dolomite flotation processes, the IMC Anionic Process and the CLDRI Process, have been successfully demonstrated on flotation feed that has not been deslimed after grinding. Deslimed flotation feed, relative to undeslimed feed, has improved flotation performance and reduced reagent consumption. However, for the above mention processes, undeslimed ground feed increases the yield of concentrate because the phosphate desliming losses are avoided.

Jan 1, 2002

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985