Search Documents

By S. J. S. Ferreira

Anglo American Platinum's Khomanani 2 shaft changed over from down-dip mining to breast mining in 2004. The changeover was made to ensure that production targets were met, as it was said that predevelopment for down-dip mining was not fast enough to sustain the required ore reserves; nevertheless, production performance did not increase as expected. In this study a trade-off was performed between down-dip mining and breast mining on the Merensky Reef at Khomanani 2 in order to find the most suitable method for mining the Merensky Reef. Data was gathered by means of a literature survey, underground observations, and interviews with personnel as well as data from various departments on the mine. The two mining methods were studied and then evaluated in terms of the following criteria: safety, mining rate, cost and other factors which were identified as the main drivers of the mine. A scaling system was used to rate the performance of the two mining methods. Analysis of the results shows that down-dip mining and breast mining have the same safety performance ratings. Breast mining has a better mining rate performance than down-dip mining. Breast mining was found to be costly in comparison with down-dip mining, which has a good cost performance rating. The overall ratings of the two mining methods are very similar, with down-dip mining achieving a rating of 76 and breast mining 75.5 out of an optimum 102. Khomanani 2 currently practices breast mining, and with such a slight difference in performance rating between the two methods, it will not be worth changing over to down-dip mining as production is likely to be adversely affected during the changeover. Down-dip mining does, however, have potential for improvement in its performance rating. Further studies focusing on the improvement of the mining rate performance for down-dip mining are needed to see if this potential can be realized. If significant improvement can be made in the performance rating for down-dip mining, a changeover to down-dip mining can be reconsidered.

Jan 1, 2012

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By S Rupprech, T Lund, H Fourie, PH van Rooyen, NM Vegter

Rosh Pinah Zinc Corporation (Pty) Ltd (RPZC) operates an underground mine at Rosh Pinah in southern Namibia producing zinc and lead sulphide concentrates. It currently mines around 0.7 Mtpa run-of-mine ore containing around 6-10% zinc and 1.5-3.5% lead. As part of past exploration and current intensified exploration, a massive continuous low grade ore body was identified which grades at around 3% zinc equivalent. This ore body is near current mining infrastructure and could be amenable to bulk mining methods. In the present paper a concept is presented on how it could be exploited. As a precursor to exploitation of the low grade a number of enhancements are proposed for the current mining operations including: ? shortening load-and-haul distances by extending the conveyor raise further down the mine in a phased manner and back-filling of waste into mined-out stopes; ? use of mobile crushing plant at the crusher tip, and; ? installation of a system to allow scoops to load directly from stopes into ore passes close by combined with truck loops to haul from these ore passes to the crusher tip. To exploit the low grade ore body the following concepts are proposed: ? open stope mining from two areas at a total rate of up to 2 Mtpa; ? underground pre-beneficiation of mined low-grade ore near the stopes using either dense medium separation or X-ray sorting; ? pre-beneficiated tails back-filled to mined-out stopes and; ? pre-beneficiated product transported to surface by linking into proposed run-of-mine conveying system.

Jan 1, 2007

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2010

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

By D. Malovichko

Seismic events and pillar failures observed in two platinum mines in the Rustenburg area, South Africa, were investigated. We studied the sources of approximately 300 largest seismic events recorded in 2009. Moment tensors of these events were estimated from amplitudes and polarities of P- and S-waves. The inverted mechanisms contain isotropic implosive components in many instances. Analyses of uncertainty of the moment tensor solutions confirmed the significance of the implosive component in general. Several documented cases of pillar failure were considered in detail. For each of these a seismic moment tensor was calculated from an elastic stress model assuming an instant removal of a failed pillar. The geometries and magnitudes of the theoretical seismic moment tensors are in agreement with the observed (i.e. inverted from seismic data). The results indicate that either pillar failure or fracturing in the proximity of the reef (within a fraction of the dominant wavelength of seismic waves) are responsible for a significant portion of the large events recorded in these mines.

Jan 1, 2012

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By S. O. Bada

Coal samples taken from the No. 2 Seam and No. 4 Seam in a South African colliery were tested in a rotary triboelectrostatic separator. The two-stage triboelectrostatic separation results using the -177 µm size fraction reduced No. 2 Seam coal containing about 30.4 per cent ash to a clean product of 8.9 per cent and 13.1 per cent ash with combustible recoveries of 9.6 per cent and 30.7 per cent respectively. The same separation approach on No. 4 seam feed coal, which contained 36 per cent ash, produced a clean coal product with 10.8 per cent ash at a combustible recovery of 6.0 per cent. Petrographic tests show a significant improvement in the vitrinite content and a reduction in visible minerals encountered when using the triboelectrostatic separator, with about 53 per cent vitrinite reporting to the clean fraction for No. 2 Seam compared to the feed content of 21 per cent, and a 54 per cent vitrinite in the clean No. 4 Seam from a feed content of 21 per cent. Significant sulphur reductions were also observed after separation in both coal samples, with a better separation in the second-stage coal products.

Jan 1, 2012

By E. H. Myrhaug, K. Aasly, T. Malvik

Six different types of quartz and quartzites used as raw materials by ferroalloy plants have been investigated with respect to their thermo mechanical properties. In order to investigate the effect of the thermal shock caused by the rapid heating of quartz when it enters the furnace, the following techniques have been used for both in situ investigations and investigations of pre-heated quartz: -Heating stage microscopy for in situ observation of heating effects. -Shock heating of quartz in an induction furnace An optical microscope-mounted heating stage was used for in situ observations of the microscopic effects of heating up to 1300 ºC. The effects of heating were observed at different temperature intervals in different samples. The main temperature intervals were below 573 ºC and above 1000 ºC. The cause of the observed effects is interpreted as fluid inclusion decrepitation for T<573 °C and structural implications (micro cracks, grain boundaries and remaining fluid inclusions) at T>1200 °C. Shock heating of the samples was carried out in an induction furnace to 1300 ºC for ten minutes. The effects of the heating were studied with different techniques such as direct observation during and directly after heating, optical microscopy and XRD. Combined transmitted and fluorescence light microscopy shows that the heated quartz show an opening of the grain boundaries and evenly distributed micro cracks that were not present in the unheated reference samples. In some of the heated samples, weak generation of cristobalite was detected by XRD.

Jan 1, 2007

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (CObalt from Slag And Copper as by-product) Project. Aniron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, andiron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambish ioperation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant. The challenges discussed include alloy handling, autoclave design, autoclave cooler design, residue liquor recovery and the water balance design. Keywords: Chambishi, Avmin, COSAC, Zambia, Copperbelt, cobalt, copper, alloy handling, pressure leach, autoclaves, cooling, filtration.

Jan 1, 2003

By C J. de Beer

The Kwaggashoek East pit is one of the four production areas of Thabazimbi Iron Ore Mine. The Kwaggashoek East Open pit mines through the abandoned sublevel caving operations of the Kwaggashoek East underground workings. A risk assessment indicated that the primary risk is the occurrence of surface subsidence. Based on local knowledge, a hypothesis, that most of the cavities were filled with broken rock as a result of roof collapse and bulking of failed material was formulated. To test the hypothesis a number of geophysical methods as well as probe drilling was utilized. The results of the resistivity, gravity and ground penetrating radar surveys were inconclusive in determining the position of voids. Either there were no voids present or the resolution of the surveys was not high enough to pick it up. It is accepted that only small voids remained, and that the supported roof hypothesis is valid. As a precautionary measure all the production blast holes within the caving area were over-drilled by forty percent. This would collapse the roof of any small voids or tunnels immediately below the block. This operation proved to be successful as two of the three underground levels have been mined out with no subsidence occurring in the pit floor.

Jan 1, 2006

By A. Navarra, A. Quelopana

The mine production scheduling problem (MPSP) has been studied since the 1960s, and remains an active area of computational research. In extending the concepts of the MPSP, the automated mine may now be regarded as a hierarchical intelligent agent in which the bottom layer consists of distributed robotic equipment, while strategic functionality occupies the higher layers. Here we present a disambiguation of artificial intelligence, machine learning, computational optimization, and automation within the mining context. Specifically, the Q-learning algorithm has been adapted to generate the initial solutions for a high-performing strategic mine planning algorithm, originally developed by Lamghari, Dimitrakopoulos and Ferland, based on the variable neighbourhood descent (VND) metaheuristic. The hierarchical intelligent agent is presented as an integrative conceptual platform, defining the interaction between our new Q-learning adaptation and Lamghari’s VND, and potentially other hierarchically controlled components of an artificially intelligent mine, having various degrees of automation. Sample computations involving Q-learning and VND are presented.

Dec 1, 2021

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By G. J. de Korte

South Africa’s best-quality coal, located in the central Highveld basin, is becoming depleted and alternative sources of coal, such as the Waterberg coalfield, will have to be developed to supply the country with coal in the future. The quality of the coal being mined in the central basin is gradually becoming poorer. This necessitates that more of the coal be processed to improve the quality to meet customer requirements. The challenge to the coal processing industry is to process low-yielding coals to produce goodquality products and at the same time ensure that coal mining remains economically viable. This requires that more cost-effective coal processing technologies be investigated and implemented.

Jan 1, 2015

1. Recent publication Iron and steel works of the world. Worcester Park (England), Metal Bulletin PLC, 1987. 9th edition, 728 pp. £94.75 by air mail.2. Canadian publications Mining and mineral processing operations in Canada, 1987. Mineral Bulletin MR 216. $15. (Obtainable from Printing and Publishing, Supply and Services Canada, Hull, Quebec, KIA 059 Canada.) Peat producers in Canada, 1986 directory, by M. Prud&apos;homme. MRI 87/7 Canadian mines: Perspective from 1986. Reserves, production capability, exploration, development. Mineral Buletin MR 215. $9.95. 3. Mintek publications Report M313 The testing of abrasion resistance in pipeline materials, by D.P. Enright. Nov. 1987. 36 pp. Report M328 The installation and commissioning of a Hilger Monospek D500 scanning monochromator, by A.E. Watson. Sep. 1987. 11 pp. Report M331 The design and operation of hot-air dryers for the drying of granular activated carbon. Nov. 1987. 30 pp. Report M338 Ore microscopy, image analysis, and the extractive metallurgy of sulphide minerals-an overview. Nov. 1987. 14 pp. Report M339 The determination, by flow-injection analysis, of sulphate in solutions containing chromium(I/I) and iron(I/I). Nov. 1987. 11 pp. Report M222D The simultaneous determination of common anions by ion chromatography, by A. Cameron and C. Pohlandt. Oct. 1985, reissued May 1987. 10 pp. Report M227D The spectrophotometric determination of silica in metallurgical-grade fluorspar, by M. Solomons. Nov. 1985, reissued Jun. 1987. 9 pp. Report M229D The determination of metalic iron in prereduced iron ores, by R. Lownsbrough. Dec. 1985, reissued Jun. 1987. 7 pp. Report M252D The spectrophotometric determination of bismuth in sulphide materials, by M. Solomons. Mar. 1986, reissued Jun. 1987. 13 pp. Special Publication no. 12 Platinum in South Africa, by A.M. Edwards and Silk. 1987. 64 pp. Illustrated in colour. R30 ( Africa), US$30 (other countries). 4. Journals of interest Industrial Minerals. London, Metal Bulletin Journals Ltd. Tin and its uses no. 154, Nov. 1987.

Jan 1, 1988