Search Documents

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of 'Google maps?' underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum's new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2013

By K. M. Banks

The hot ductility of in situ melted tensile specimens of micro-alloyed steels having C contents in the range 0.12?0.17% (mass %) have been examined over the 700?1000°C temperature range. An improved testing method for simulating the continuous casting process was used, which takes into account both primary and secondary cooling conditions. Increasing the N content to electric arc furnace levels (0.01% N) was found to cause a serious deterioration in ductility. V-N steel gave better ductility than Nb-containing steels due to less precipitation. From a cracking perspective, low- N steels are generally recommended but, when not feasible, a combination of Nb and V gives even better ductility. However, to be sure of avoiding transverse cracking in higher N steels a small addition of Ti is required. This resulted in a decrease in the fraction of fine particles and in accord with this better ductility. Transverse cracking of industrial slabs was then avoided.

Jan 1, 2011

By A. Whillier

Recovery of energy from the water going down mine shafts by A. WHILLIER, Pr. Eng., Se. D. (M.I.T.) (Fellow) The influence of energy-recovery systems on the rise in temperature of water going down mines is examined. It is concluded that the, cost benefit of such systems, deriving partially from the reduced temperature rise in situations where cold water IS sent underground from surface, would more than justify the installation cost.

Jan 4, 1977

By J. S. C. Joubert

The Koidu Kimberlite Project is situated in the Kono District of Sierra Leone, approximately 330 km east of the capital city, Freetown. The mining lease area is 4 km2 and comprises 2 kimberlite pipes, 4 dyke zones and a number of blows off the dykes. Koidu Holdings established on the property and began dewatering and the removal of silt from the existing 30 m excavation of the No.1 Pipe in 2003. While the original planning for the pipes included conventional open pit operations, mitigating factors such as the proximity of the town, the presence of houses close to the perimeter of the pipe, the size of the pipe and the planned open pit depth with relevant stripping ratios, as well as uncertainties on the grades in respect of an underground operation, lent itself to the vertical pit concept. The vertical pit was established using an A-frame headgear for the hoisting arrangement, with sidewall support comprising a combination of 20 m and 40 m long cable anchors, rock bolts, wire mesh and pneumatically applied concrete. The pit reached steady state production in January 2007 and produced some 26,000 tonnes of head feed per month until August 2007 when mining reached a depth of 74 m below the pit collar (approximately 126 m below surface). Mining was suspended following a sidewall failure that disrupted operations. Now that the grades in No.1 Pipe have been validated, focus has been switched to an underground operation taking account of both No. 1 Pipe and No. 2 Pipe. While the mining costs for the vertical pit have been higher than for a conventional open pit, the concept did circumvent the social implications, the issue of grade consistency and diamond value at depth, as well as providing the time frame to carry out a full underground mining study.

Jan 1, 2008

By N. C. Joughlin, D. K. Hallbauer

The size distribution and morphology of gold particles in Witwatersrand reefs and their crushed products by D. K. HALLBAUER, Dr. rer. nat., Dipl. Min. (Visitor) and N. C. JOUGHIN, B.Se. (Eng.), Ph.D. (Rand) (Member) Undistorted gold particles were obtained from samples of a variety of Witwatersrand reefs by dissolution of the quartz in hydrofluoric acid. The size distribution of the gold particles and their shapes and association with thucholite and pyrite are discussed. Gold particles with a natural flat, plate-like appearance occur in varying proportion in all reefs. The effect of a number of different comminution processes on the gold particles was investigated, and the shape of gold particles in mill pulp from a number of mines was examined.

By S. Tshikhudo

This paper outlines an investigation into the recovery of saleable fractions of coal from ?as-arising? South Export Plant effluent streams, using Baleen microscreening technology. South Export Plant, a subdivision of BHP Billiton Energy Coal SA (BECSA) Coal Processing, is a two-module plant treating 2000 t/h. The nominally -150 µm coal is untreated and is therefore passed from classifying cyclones to the thickeners for process water recovery. The thickened underflow is pumped into a series of slurry cells for further settling and recovery of supernatant water. The marginal quality, moisture content, and handlebility of this settled material renders it unsuitable for inclusion into saleable products and it is thus stockpiled and trucked to designated pits for disposal. Over the years, stockpiling and trucking has become an overly expensive exercise. In an effort to recover some of this cost, a task team was assigned to investigate less costly options to process slurry across BECSA plants. Various technologies such as froth flotation, sieve bends, and Reflux Classifier were considered, although the results were generally not beneficial ? this could be attributed to weathered/oxidized coal. A decision was made to pursue an alternative approach by testing the suitability of the new ?Baleen Filter?. The concept is to screen out the higher-grade fraction (+50 µm) as saleable product and reject the finer fractions to the slurry ponds. The Baleen Filter was found to effectively screen at an acceptable efficiency between 94% and 99.99%, with a very sharp cut-point (d50 and Ep). The actual yields from the screening results were better than the predicted yields in terms of both mass and energy as predicted from feedstock analysis.

Jan 1, 2014

By F. P. A. Robinson, C. R. Thomas

Stress-corrosion studies on materials used for surgical implants * by C. R. THOMAS and F. P. A. ROBINSON Samples of Vitallium (a cobalt-chromium alloy), 316L stainless steel, and titanium T318 were subjected to the boiling magnesium chloride test so thattheir susceptibility to stress-corrosion cracking could be determined, and their behaviour under service conditions was then assessed. Stress-corrosion cracking was confined to the stainless-steel samples, while gross pitting was detected in the samples of forged Vitallium. It was concluded that the use of stainless steel should be avoided for long-term surgical implants. Surface imperfections on the stainless steel are generally the cause of pitting, from which stress-corrosion cracks are sometimes propagated.

Jan 11, 1976

By C. H. Wyndham, N. B. Strydom

INTRODUCTION Acclimatization of the labour force to heat is an integral aspect of gold mining in South Africa. A recent survey revealed that about 250,000 Bantu mine workers require to be acclimatized to heat each year. Until 1965 men were acclimatized by means of one of the Chamber of Mines methods (introduced by the Human Sciences Laboratory in 1953). This type of acclimatization was carried out underground where men shovelled rock in hot stopes under careful supervision. However, it has become increasingly difficult in the last few years for mines to provide underground the conditions of work and environmental heat required for adequate acclimatization to heat. In examining an alternative to acclimatization in underground hot stopes, the Human Sciences Laboratory carried out a trial in 1965 of acclimatization in an air-conditioned climatic room on the surface of a mine. The new procedures developed from this trial have been so successful that there are today 26 climatic rooms on different mines. These rooms have been built following a design proposed by Mr Hodgson of the National Mechanical Engineering Research Institute1. Approximately 85 per cent of the total number of men being acclimatized each year are put through the new procedures in these climatic rooms. This paper gives an account of the problems which arose and how they were solved, the inter-relationship between physical conditioning and climatic room acclimatization, the prodecures developed for elimination of labourers with low maximum oxygen intakes, and the advantages of climatic room acclimatization. CLIMATIC ROOMS The majority of the climatic rooms (twenty) have been built on the surface, but a number (six) of mines preferred to establish their acclimatization centres underground in order to decrease the initial costs involved in the construction of such facilities. These underground climatic rooms are usually located near shaft stations in redundant haulages and they can accommodate from 200 to 400 labourers, thus eliminating the need for multiple acclimatization shifts. Figs. 1-4 illustrate various aspects of a surface climatic room. PROBLEMS WHICH AROSE IN INTRODUCING CLIMATIC ROOM ACCLIMATISATION There were four main problems which arose in connection with the introduction of the new method. These were: (i) The type and rate of work to be used. (ii) The air conditions required to obtain optimum acclimatization. (iii) The duration of exposure to heat each day and the total number of days of acclimatization. (iv) The methods of cooling labourers with high body temperatures. Shovelling rock would have been the desirable type of physical work to employ, but the air-conditioned space required to accommodate large numbers of men and the difficulty in standardizing the work rate in shovelling led to the decision to employ instead the work procedure used by the Human Sciences Laboratory in acclimatizing men in the Laboratory. This is the lifting of the body weight against gravity when men step on and off a bench. It has the advantage that large numbers of men can work physically at the required rate in a relatively small space (120 men can be accommodated in an area of 70 ft by 21 ft) and the cost of construction and ventilation of the climatic rooms is thereby reduced. Also the work rate can be standardized by varying the height of the stepping benches in relation to the individuals' body weights. The next problem was the air condition to be used in the climatic rooms. The Laboratory's research experience in acclimatization led it to choose an air temperature of 89°F (with the air almost saturated with water vapour) and an average velocity of air movement of 100 fpm. This air condition was combined with a work rate of 1,560 ft lb/min (oxygen consumption 1.0 litre/min) on day 1, and the work rate was increased gradually over the period of acclimatization to reach a work rate of 3,120 ft lb/min (oxygen consumption 1.6 litres/min) on day 9.

By G. Drennan, A. Cameron

"South African mining operations depend on the skilled professionals produced through the tertiary education sector. In geoscience courses at the University of the Witwatersrand, which lead into the mining sector, there has been a significant increase in student intake over the past 15 years. This increase has been characterized by a radical shift in demography: in classes where white male students once formed the majority, black female students are now in the majority. This demographic shift appears closely linked to policies addressing issues of social justice and transformation in post-apartheid South Africa. We document this change and consider the role played by employment equity legislation (as in the Mining Charter) and corporate social investment strategies in the mining industry, notably through bursaries offered to black female students. We also look at the changing needs of the industry, where the critical need for managerial skills, not just technical knowledge, is highlighted through data from surveys of past students and industry managers. Our findings indicate the need for a curriculum adjustment to meet these changing requirements, as well as more rigorous selection criteria for bursars than simply gender, race, and appropriate matric results. IntroductionThe South African economy has historically been linked to mining and the exploitation of mineral resources. South African mining operations are dependent on the professional labour that is produced through the tertiary education sector, with critical thinking, teamwork, and the art of negotiation having been identified as the crucial skills required for this industry (Sideropoulos, 2014). Over the past three decades the South African system of education has gone through a period of dysfunction that it is struggling to rectify (Maphai, 2014). This has impacted on the levels of academic preparedness of students applying for places in higher education. Concurrently, government and university policies have widened access to higher education in response to the need to address issues of social injustice and transformation related to South Africa’s history of apartheid. As a result, the number of students admitted to universities has increased dramatically. In the School of Geosciences at the University of the Witwatersrand (Wits), the increase in student numbers has been accompanied by a significant change in demographics: classrooms which in the past were dominated by white males have given way to classrooms in which black females are often in the majority. This demographic shift is related to legislation such as the Mineral and Petroleum Resources Development Act and the Broadbased Socio-Economic Empowerment Charter, developed to reshape the socio-economic and equity frameworks of the country (Botha and Cronje, 2015). Requirements aimed at transformation in terms of management, skills development, and employment equity, together with corporate social investment (CSI) requirements, have resulted in bursaries being made available to attract students from designated groups, which in turn has increased the number of black students, and notably black female students, taking courses in geosciences. However, due to the economic downturn, instability in the mining industry has recently resulted in the downsizing of some mines, with international investors pulling out of South Africa. This instability resulted in devastating strikes across all sectors of the mining industry (Stewart, 2013) and in Marikana, an important platinum mining area, the strike culminated in a deadly shoot-out between miners and police. The resulting tensions spilled over into the gold mining sector, resulting in further strike action, shaft closures, and retrenchments. These challenges have implications not only for the mining industry in South Africa, but for the tertiary education providers whose graduates would have been absorbed into the mine-related workforce."

Jan 1, 2017

By I. Satola, J. Aromaa

In this work we have reviewed methods to classify corrosivity of ground waters. Weight loss and stress corrosion cracking (SCC) corrosion tests have been done for rebar and steel strand. No clear indication of SCC was found. The application of tensile stress to 85 % of yield strength increased general corrosion rate significantly in very corrosive waters. The effect of corrosion protection on the axial behavior of steel strands was determined by double pipe axial tests with different embedment lengths. The results showed a significant difference on behavior between epoxy-coated steel strands, galvanized steel strands and plain steel strand. Dans la présente étude, nous avons passé en revue des méthodes permettant de classifier la corrosivité des eaux souterraines. Des tests portant sur les pertes de poids et sur la corrosion FCC (la fissuration par corrosion sous contrainte) ont été effectués pour les barres d’armature et les torons. Aucune indication nette de FCC n’a été constatée. L’application d’une contrainte de traction allant jusqu’à 85 % de la limite d’élasticité a accru de manière significative la vitesse générale de corrosion dans les eaux très corrosives. L’effet de la protection contre la corrosion sur le comportement axial des torons en acier a été déterminé au moyen de tests axiaux à double tube avec des longueurs d’enrobage différentes. Les résultats ont mis en évidence une différence significative quant au comportement entre les torons en acier à revêtement époxy, les torons en acier galvanisés et les torons en acier standard. In dieser Arbeit haben wir Methoden geprüft, die korrosive Wirkung des Grundwassers einstufen. Gewichtsverlust- und SCC-Korrosionstests wurden für Stahlstäbe und Drahtlitzen durchgeführt. Es wurden keine sicheren Hinweise auf Spannungsrisskorrosionsbrüche gefunden. Bei Anwendung einer Dehnbelastung von 85 % der Streckspannung bzw.Ergebnisstärke stieg die allgemeine Korrosionsrate in stark korrosivem Wasser deutlich an. Die Wirkung des Korrosionschutzes bei axialem Verhalten von Stahldrahtlitzen wurde durch axiale Tests an Doppelleitungen unterschiedlicher Versenkungslänge determiniert. Die Ergebnisse zeigten im direkten Vergleich von epoxidbeschichteten, galvanisierten und normalen Stahldrahtlitzen beachtliche Unterschiede im Verhalten auf.

Jan 1, 2003

By A. G. Ramsay, P. G. Kahles, L. E. Kun

A method for the clarification of uranium pregnant solutions using a high-rate floc blanket was developed from laboratory scale through pilot-plant testing to full-scale production by the Anglo American Research laboratories. A two-stage clarification process (hopper plus leaf) was commissioned at the Western Deep levels uranium plant in October 1980. The high efficiency of the hopper clarification permitted its use on its own. The leaf clarifiers were therefore taken out of service in September 1981, since when the secondary clarification is achieved by further unaided gravity settling in the semi-clarified and clarified pregnant-solution storage tanks. As a result, a daily 12000 to 17000 t of countercurrent-decantation overflow with a suspended-solids concentration of 500 to 600 mg/I is continuously clarified to a suspended-solids concentration of less than 30 mg/I. Secondary gravity settling reduces the suspendedsolids concentration to under 20 mg/I. The cost of the single-stage hopper-clarification process is RO,O020per ton of liquid treated. The removal of the leaf clarifiers from the circuit resulted in an approximate visible saving of RI00000 per annum.

Jan 1, 1983

A mineralogical study was conducted on the feed (3.51 g/t Au and ~90 g/t Ag) and four leach residue samples (assaying 0.09 to 0.19 g/t Au and 30.0 to 61.5 g/t Ag) from the Pinos Altos silver-gold deposit in Mexico to determine the cause for gold and silver losses. A comprehensive mineralogical and analytical approach including fire assay, gravity pre-concentration, ore microscopy, mineral liberation analyser (MLA) and electron microprobe was used for the current study. Results showed that gold and silver lost in the leach residues occurred mainly as inclusions in quartz and silicates (accounting for over 80% for Au and 92% for Ag of the head assays, respectively), with a minor amount in iron oxide and other minerals. The amount of liberated gold and silver is negligible. Results also showed that gold and silver particles in leach residues are mainly ranged from 1 µm to 5 µm in size, which implies that ultrafine grinding is required to improve the recoveries of these two metals. Keywords: mineralogy, gold deportment, silver deportment, silver-gold ore, leach residue, recovery improvement.

Jan 1, 2009

By R. R. M. Cousens, W. S. Garrett

Discussion: L. T. Campbell Pitt: When Mr Garrett and I discussed the design and construction of plugs and bulk head doors to resist great water pressures in mines about ten years ago, we visualized an emeregeny when there would be no time for site preparation. We could not however, anticipate a problem of such magnitude and urgency as the one described in the paper under discussion. The paper very clearly describes the flooding and the measures taken to save the mine. The complete flooding would have been a national disaster. The account of the combat between man and water reads like the account of a military operation. It was an endeavour which achieved success because there was a master plan, tenacity and, in fact, heroism. The paper is of necessity a long one. In my contribution I will mention some historical facts and factors that I believe have relevance to the flooding and the saving of the mine. It is of great satisfaction to me to have been one of the two initiators of a new approach to underground plug design and construction. The investigation was taken over by a Chamber of Mines Committee which combined our early work with further research and the resulting data had a significant bearing on the West Drie emergency plug designs. The final plug length was correctly based on the requirements to obviate leakage. A plug to have structural strength only would have been very much shorter but so ineffective as to have become a waste of labour, material, and in consequence, wasted the limited time available to prevent flooding of the whole mine. The figure of 75 lb per sq in. sheer stress provided a very ample margin, in my opinion, but under the very difficult site conditions and the limitations of plug material suitable for the very unusual construction, justified such a figure. There must have been considerable temptation to reduce the safety margin due to the urgency to complete and commission the plugs, but it is much to the credit of the directors of this operation that nothing less than a safe design was permitted. In about 1945 Blyvooruitzicht Gold Mining Company, which was then mining in to the West Driefontein area to assist in early development, decided to protect themselves from a possible inrush of water from the latter mine. A bulk head door was accordingly designed and installed on 2 level between 1945 and 1948 at 4,218 ft below surface. Since West Driefontein paid for it, Gold Fields consulting mechanical engineers collaborated with their colleagues of Rand Mines who completed their design after a few modifications were agreed. This door was never used to prevent an inrush into Blyvooruitzicht but the exercise was very useful to Gold Fields when the high pressure doors initially installed on 10 and 12 levels between Nos. 2 and 3 shafts to enable isolation of one section of the mine from another were designed. At that time the capacity of West Driefontein to cope with an inrush of water was comparatively small because the storage in stoped areas and the installed pump capacity were much less than in later years. These doors together with others of the same design were later moved to the lower levels served by sub vertical shafts. In addition, doors to prevent flood water entering the pump chambers on 18 level were installed at each end of that level, and designed for a head of 360 feet so that water would have to reach 16 level before the pumps were flooded. All these doors were called upon to hold water and it is reported that only a small plug in one of the doors and a 4 in. dia flanged pipe joint failed. The lesson is that in these cases the smallest details warrant as much attention as the major ones. That these were the only equipment failures when so much depended on equipment, is very much to the credit of design engineers, both of the Gold Fields head office and companies who supplied both mechanical and electrical equipment. Until I had read the paper I wondered why the policy of isolation by bulk head doors was not continued as the development moved eastward towards the Bank Compartment and particularly when it pierced the Bank dyke. The reasons have been given in the paper. It was unreasonable to expect provisions to be made to counter the remote contingency that the large installed pumping capacity and mine capacity to store water would be exceeded during a peak inrush. When pumps were being considered for West Driefontein, it was decided that the Gold Fields standard underground main pumps at that time of 1 million gallons per 24 hours would be too small. Three alternatives were considered. 1. Very large units that would require underground sub assembly and dismantling of both pump and motor. 2. The largest pump and motor that could be conveyed as a complete pump or motor from surface to the pump chamber. 3. Pumps of higher speed to reduce dimensions and weight. It was decided to adopt alternate 2 because of avoidance of transporting pumps in parts and assembling underground. Alternative 3 was not favoured because high speeds would have introduced problems of more exact rotor balancing. I believe the decision was correct and in the crisis enabled comparative easy transport of pumps and motors to surface for overhaul and, if required, transfer to other pump stations. The standard pump thus became a 10 stage 1,500 rpm pump with a capacity of approximately 2 million gallons per 24 hours against a static head that varied

Jan 3, 1969

The role of research and development In the South African gold-mining industry Presidential Address given by M. D. G. SALAMON, Fellow, Dipl. Eng. (Mining) (Hungary), Ph.D. (Durham) The decision of the gold-mining industry in 1974 to embark on a major ten-year research and development programme was widely publicized at the time. In choosing a subject for this address, I felt almost obliged to use this opportunity to give an account of the progress of this undertaking. On reflection, however, I felt that a simple progress report would not suffice. It seemed important that the programme should be shown in persepective, and that its aims should be outlined to the mining and metallurgical engineering community, many of whom are vitally concerned with the well-being of the gold-mining industry.

Jan 10, 1976

By C. Montoya

This paper shows, through a case study, the impact of multivariate grade modelling upon mine design and mine planning. A deposit explored by drill holes is considered, in which the grades of five elements (copper, silver, molybdenum, arsenic, and antimony) are of interest. Forty alternative models of the deposit are constructed by fitting the joint correlation structure of the grade variables and using conditional cosimulation. In addition, a reference model, obtained by averaging the alternative models, is also considered. The study shows that the resulting mine design (final pit characteristics and production schedules) is sensitive to the grade model under consideration, and that the design based on the reference model may not be optimal when compared to the alternative models based on cosimulation. However, when assuming a given long-term plan and extraction sequence, the grades and net present value (NPV) calculated on the reference model are unbiased with respect to those calculated on the alternative models with the same extraction sequence. The latter allow assessing the possible dispersion of the actual grades and NPV around their expected values, and are useful for the planner in order to determine the probability of meeting given production targets and of exceeding or falling short of given threshold grades. Additionally, unlike cosimulation, the separate simulation of each grade variable leads to unrealistic resource models and to biased results in mine design and mine planning. This approach should therefore be avoided, unless the grade variables are spatially uncorrelated.

Jan 1, 2012

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 22nd August, 1979. Dr M. G. Atmore (President) was in the chair and declared the meeting open at 16h00. Obituaries President: It is my sad duty to announce the death of the following Members of the Institute : Brigadier R. S. G. Stokes, Honorary Life Fellow and Past President ; J. A. Arthur, C. L. Cartwright, R. B. Greaves, A. A. Haynes, G. Ross, M. W. Richards, W. T. Stobart, E. Veres, G. V. White, and A. G. Williams, Life Fellows; A. J. H. Pole, D. T. McMurray, P. G. O. Pretorius, A. E. D. Rubidge, A. M. Seccombe, and R. R. Uren, Fellows; R. E. Oltman, R. B. Richardson, and G. P. Rundle, Members; S. F. Dench and S. van Wyk, Associates. As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, please rise and observe a few moments' silence. Minutes President: May we confirm the minutes of our last Annual General Meeting, which was held on 23rd August, 1978, as published in the November issue of the Journal? Agreed.

Jan 1, 1979

By M. Cuba

Geostatistical modelling aims at providing unbiased estimates of the grades of elements of economic interest in mining operations, and assessing the associated uncertainty in these resources and reserves. Conventional practice consists of using the data as error-free values and performing the typical steps of data analysis - domaining, semivariogram analysis, and estimation/simulation. However, in many mature deposits, information comes from different drilling campaigns that were sometimes completed decades ago, when little or no quality assurance and quality control (QA/AC) procedures were available. Although this legacy data may have significant sampling errors, it provides valuable information and should be combined with more recent data that has been subject to strict QA/QC procedures. In this paper we show that ignoring the errors associated with sample data considerably underestimates the uncertainty (and consequently the economic risk) associated with a mining project. We also provide a methodology to combine data with different sampling errors, thus preserving the relevant global and local statistics. The method consists of constructing consistent simulated sets of values at the sample locations, in order to reproduce the error of each drilling campaign and the spatial correlation of the grades. It is based on a Gibbs sampler, where at every sample location, the actual sample value (with error) is removed and a conditional distribution is calculated from simulated values at nearby sample locations. A value is drawn from that distribution and kept only if it satisfies some statistical requirements-specifically, the global relative error and local means and variances must be reproduced. All sample locations are visited and simulated sample values are generated iteratively, until the required statistics are satisfactorily attained over all sample locations. This generates one realization of possible sample values, respecting the fact that the actual samples are known to carry an error given by the global relative error. Multiple realizations of simulated sample values can be obtained by repeating the procedure. At the end of this procedure, at every sample location a set of simulated sample values is available that accounts for the imprecision of the information. Furthermore, within each realization, the simulated sample values are consistent with each other, reproducing the spatial continuity and local statistics. These simulated sets of sample values can then be used as input to conventional simulation on a full grid to assess the uncertainty in the final resources over large volumes. The methodology is presented and demonstrated using a synthetic data-set for clarity.

Jan 1, 2012

By J. Petersen, H. Naderi, M. H. Nikzad, M. Karimi

In this research, the thermodynamic study of sodium persulfate (Na2S2O8) solution in the presence and absence of H2SO4 and Fe3(SO4)3 was done. Eh-pH and equilibrium distribution diagrams were constructed using Outotec HSC Chemistry Software and the main stable ionic species were determined. Also, the mean activity coefficient and Pitzer model coefficients were evaluated. Effects of system composition, sodium persulfate concentration and temperature were investigated. According to the results, HS2O7 -, HS2O8 -, S5O3 2-, S4O3 2-, S3O3 2-, HS- and NaSO4 - are the main stable species in these three systems. Increasing of sodium persulfate concentration resulted in disappearing of SO4 2- and the appearance of NaSO4 -. The main effect of increasing the temperature from 25 to 75oC, is changing the stability regions of HS2O7 -, NaSO4 -, SO4 2- and S2-. From equilibrium studies, it was concluded that at 25 and 50oC, increasing the persulfate concentration results in a 55-60% decrease for HS2O7 - and an 20- 30% increase for HS2O8 -. At 75oC, HS2O8 - becomes the main species and its percentage decreases with increasing the persulfate concentration. Keywords: Thermodynamic, sodium persulfate, activity coefficient

Jan 1, 2020

By A. P. I. Popoola

Aluminium AA1200 was laser alloyed with a combination of nickel and titanium diboride using different weight ratios. Chemical reactions took place with the formation of different phases. The characterization of the alloyed surfaces was carried out by x-ray diffraction (XRD), optical and scanning electron microscopes. The alloyed surfaces are composed of the initial phase of Al-Ni dendrites and eutectics of TiB2/Al and TiB2/Ni distributed on the initial phase. Experimental results obtained showed that Al-Ni intermetallics brought about a significant increase in the hardness property of Al; however, these intermetallics are highly brittle and prone to fail by brittle fracture or stress corrosion cracking when put in service. The addition of TiB2 brought about a reduction in the formation of the seintermetallic phases. A microhardness increase of over 10 times the hardness of the substrate was achieved. Keywords Dendrites, intermetallics, metal composite, Nd: YAG laser.

Jan 1, 2011

By J. J. Cilliers, J-A. Lamamy, J. N. Rasera, K. Hadler

Production of oxygen on the moon can be achieved by reduction of lunar soil. One such reduction technology, hydrogen reduction, favours a high proportion of ilmenite in the feedstock. Ilmenite is present in lunar soil as a minor mineral phase, but it can be upgraded using electrostatic separation. This study presents the results of a preliminary investigation into the operating parameters and sensitivities of a free-fall electrostatic mineral separator for lunar applications. Samples of ballotini and ilmenite as well as simple binary mixtures of the two were tribocharged on copper and passed through a uniform electrostatic field. The field is varied to change the electrostatic force acting on the particles. The proportion of material reporting to the positive electrode collectors, negative electrode collectors or the central collector was measured to determine the separation performance. The data confirmed that the charge transferred from the tribocharger to each species is in agreement with the triboelectric series; ballotini was found to charge positively on copper and ilmenite negatively. Particle-particle contacts were dominant, however, resulting in a somewhat symmetrical particle distribution in the collectors. These findings indicate that the copper tribocharger design requires optimisation in order to substantially increase particle-wall contacts. Four binary mixtures with feed grades of ilmenite ranging from 5% to 20% were prepared and tested. This study found that a higher ilmenite head grade resulted in a higher concentrate grade (26.3% from a head grade of 20%) with low recovery (3.4%). In contrast, the lower feed grade resulted in a low concentrate grade but higher recovery. The mass yield of ilmenite was 1.4 times greater for the highest-grade feed than for the lowest. A subsequent study into the reprocessing of middling fraction found a nearly constant relationship between cumulative grade and recovery. This is the first investigation into the effect of feed grade on the concentrate grade and recovery for lunar mineral processing. Keywords: Lunar resources, beneficiation, electrostatic, SRU, ISRU

Jan 1, 2020