Search Documents

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By S. K. Murphy, S. M. Spottiswoode, A. M. Milev, D. Geyser

A portable, stand-alone instrument especially designed for recording strong ground motion was used in this study to create a large database of peak particle velocities measured underground. A total number of 39 sites located in stopes mining Carbon Leader and Ventersdorp Contact Reefs were investigated. Peak particle velocities whith values up to 3 m/s were recorded at some sites. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response. The maximum site response was obtained for source radii of between 5 m and 30 m and events locating within 200 m of the site. The extreme values of peak particle velocities were obtained in cases were the face-area lay within the source radius. Un instrument portable unique spécifiquement conçu pour enregistrer les mouvements dynamiques des terrains, a été utilisé dans cette étude pour créer une base de données importante sur la vélocité maximum des particules, mesurée en souterrain. Un nombre total de 39 sites situés dans les excavations exploitant les récifs appelés ‘Carbon Leader et Ventersdorp Contact Reefs’, a été investigué. Une vélocité maximale avec des valeurs allant jusqu’ à 3 m/s a été enregistrée sur certains sites. Les données enregistrées sur le bord de l’excavation ont été comparées aux données enregistrées par les réseaux séismiques de la mine pour déterminer la réponse du site. La réponse maximum du site a été obtenue pour des sources de rayons entre 5 m et 30 m et des évènements situés dans les 200 m du site. Les valeurs extrêmes de vélocités maximales ont été obtenues pour les cas où la zone de face se trouve à l’intérieur du rayon de la source. Ein mobiles, alleinstehendes Instrument, speziell entworfen um starke Formationsbewegungen aufzuzeichnen, wurde in dieser Studie verwendet um eine große Datenbank von Partikelspitzengeschwindigkeiten, die Untertage gemessen wurden, aufzuzeichnen. Eine Gesamtanzahl von 39 Aufstellungsorten in den Schichtabbauorten vom Carbon Leader und Ventersdorp Contact Reef wurden untersucht. Partikelspitzengeschwindigkeiten mit Werten bis zu 3 m/s wurden an einigen Standorten aufgezeichnet Die an der Oberfläche des Grubenraumes aufgezeichneten Daten wurden mit jenen Daten verglichen, die vom seismischen Netzwerk der Grube notiert wurden, um die örtliche Reaktion des Standortes zu bestimmen. Die maximale Standortreaktion wurde für Ursprungsradien von zwischen 5 m und 30 m erhalten und Ereignissen die sich innerhalb von 200 m vom Standort befanden. Die extremen Werte der Partikelhöchstgeschwindigkeiten wurdenin jenen Fällen erreicht wo sich der Abbaubereich innerhalb des Ursprungsradiuses befand.

Jan 1, 2003

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Experiments were conducted to study the influence of temperature, particle size and ore/coke ratio on the kinetics of reduction. The rate of reduction increased with temperature. The reduction of iron was completed at shorter time intervals at temperature above 1000ºC. Usually the reduction of chromium commenced after the reduction of iron was almost complete. Reduction was controlled by diffusion at low temperatures and by chemical reaction at higher temperatures. The nature of the reducing agent had a very significant influence on the rate of reduction. The study showed that chromium was converted into the carbide during reduction. Increasing the size of the reducing agent increased the rate of reduction initially. After a critical size, the rate of reduction decreased. However, increasing the size of the ore particle decreased the rate of reduction, initially. Beyond a critical size, it increased. An optimum particle size of the chromite ore and that of coke must be chosen, particularly in the production of agglomerates to achieve maximum degree of reduction.

Jan 1, 2007

By A. P. I. Popoola, T. J. Olaniyi, A. A. Adeleke

"A laboratory froth flotation experiment was conducted on a low-grade carbonatite copper ore sample obtained from Phalaborwa in the Limpopo province of South Africa. The sample was a homogenous hydrocyclone overflow which serves as the feed to the flotation cells at Palabora Mining Company (PMC). The sample has an average copper assay of 0.59% with predominant copper-bearing minerals being chalcopyrite, bornite and cubanite. The carbonatite nature of the ore comes from the high content of calcium (28.85%) and magnesium (6.84%) minerals. Collectors used were sodium diethyl dithiocarbamate and potassium ethyl xanthate alongside Senfroth 38 supplied by Senmin. The results showed that at 200 g/t mixture of collectors (50:50), an optimum grade of 8.03% Cu in the rougher flotation concentrate was achieved at 74% recovery, while during the second flotation, 24.65% Cu was obtained at 74.4% recovery using a Senfroth 38 dosage of 6 L/t with 100 g/t mixed (50:50) collectors. The particle size and pH value of the pulp played a significant role in that the mixed collectors performed efficiently at pH above 8.3 and at room temperature while particle sizes greater than 53 µm were well concentrated when compared with those of less than 53 µm. INTRODUCTION The need for copper ore concentration research is on the rise as a result of the depletion of deposits and the advent of low-grade copper ores. Although most copper ore deposits have other valuable minerals that support their economic extraction, the increase in technological innovations as regards copper usage and applications has increased the demand for copper. Several factors influence concentration results in a froth flotation column, of which the reagent used is most influential."

Jan 1, 2015

By W. Kint

More than 10 years ago, one of MECS?s current partners KVT developed the so called SULFOX process for cleaning waste gases containing sulfuric compounds. In this Wet Acid Process (WAP) compounds such as SO2 and H2S, CS2, COS are oxidized over catalyst bed(s) to SO3 and finally sulfuric acid is formed. The individual plants are designed according the feed gas concentrations and customers requirements to keep the investment and operating costs as low as possible. MECS strongly believes the technology we propose will meet all your expectations. Thanks to our vast experience in the construction of sulfuric acid plants (MECS built over 800 sulfuric acid plants worldwide) we were able to design you a very reliable installation. MECS is offering the metallurgical industry, besides our conventional acid plant technology (for strong SO2) and our DynaWave? scrubbing technology (for very low SO2), a SULFOX wet acid plant (for the mid range SO2 concentrations) including an optional upstream DynaWave gas cleaning plant if required. See the figure below. Besides providing advanced technology, MECS is the only company who designs and manufactures its own key critical equipment. We manufacture our own catalyst, mist eliminators, acid distributors and coolers. Because of our in-depth technology knowledge, we understand the critical aspects necessary for making optimum equipment designs. With this combined supply of technology and key critical equipment, we can make a single overall guarantee second to none other in the world.

Jan 1, 2009

By J. L. van Niekerk, J. Gunaselvam

This study investigates the use of appropriate seating systems for the control of whole-body vibration exposure in vehicles used in the SA mining industry. Six suspension seats were tested with six test subjects to determine the most suitable seat for an articulated dump truck based on the EM1 requirement in ISO 7096 (2000) standards. Transmissibility functions were measured in the laboratory using the newly commissioned Dynamic Seat Testing Facility with two excitation levels of 1m/s2 and 2 m/s2 r.m.s. in the 0.5 - 30 Hz frequency range. SEAT values were calculated for two input spectrums, the EM1 input spectrum specified as in ISO 7096:2000 and measured road vibration data measured on a typical articulated dump truck. The averaged SEAT value calculations indicated that not one of the seats will qualify as an ISO 7096 (2000) suspension seat but that it is possible to select a seat that will significantly reduce the vibration the driver will be exposed to.

Jan 1, 2003

By R. Peroni, J. Kopp

Mine planning and scheduling is based on using a geological model for the deposit. Blocks are used to discretize the deposit into mineable volumes where grade values are assigned. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for this task where an interpolated value is calculated within a discrete volume. This group of block grades is the input for sequence optimizers, which base their decision on the economical value of a given block. Ultimately, the economical value of a block depends on its grade, making mine sequencing sensitive to all estimated values. If one looks to a block not as a single grade but as a set of equally possible grades, its economical value will change as different grades can be assigned to it. Stochastic simulation is known to provide the tools to assess grade variability, which makes it possible to generate equally probable values in a block. Different grade block models can thus be built and multiple sequencing alternatives are observed by running the optimizer for these distinct inputs. The results demonstrate that the methodology is adequate for risk assessment and proves to be useful for mining project sensitivity analyses. Differences in the project net present value showed that there is little difference between the two simulation methodologies (sequential Gaussian simulation and sequential indicator simulation) applied. The process is demonstrated using a Brazilian kaolin deposit. Keywords: geostatistical simulation, mine planning, sequencing, risk assessment, open pit optimization.

Jan 1, 2003

By X. B. Zhao, J. G. Cai

The purpose of this paper is to incorporate the dynamic BB model of rock fracture normal behaviour into Universal Distinct Element Code (UDEC), and to conduct UDEC modelling to predict stress wave propagation across rock fractures. With the incorporation of new dynamic model of fractures, the UDEC is improved in the capability of modelling wave propagation across fractures. In this study, the case of normally incident P-wave transmission across a fracture is modelled, and the effect of dynamic normal behaviour of fracture is concentrated on. Wave transmission coefficient for wave transmission across the fracture with the dynamic BB model is obtained for various combinations of fracture dynamic parameters, as well as different wave amplitudes and frequencies.

Jan 1, 2003

By J. A. Beukes, M. Marais

TICOR South Africa is a new titanium feed stock producer. In the Ticor South Africa plant the ilmenite feed to the smelter plant is roasted to enhance its magnetic properties. This allows for the magnetic separation of chromite from the ilmenite. The magnetization reaction relies on partial oxidation with both under- and over-oxidation causing insufficient magnetization. To subject the roaster plant feed material to the required physical conditions a circulating fluid bed (CFB) roaster is used. This paper describes the development of a laboratory model that will aid in the control of the CFB roaster.

Jan 1, 2003

By R. Zivojinovic, S. Vujic

The structural age of the capital mining machinery, representing a part of the system of the Electric Power Industry of Serbia, has been dictated by the initiation and development of open pit coal mines. For example, the oldest bucket wheel excavators were installed some thirty-four years ago, and the average life of the relevant machinery exceeds twenty-two years. Operation of both capital equipment and machinery has direct effects on economic and business activities of open pit mines, and consequently forced us to make a decision and study thoroughly the problem of establishing the optimum exploitation life of capital mining equipment at the open pit coal mines of the Electric Power Industry of Serbia. The aim of this paper is to define and discuss the relative problems as well as to find out the possible solutions and establish the methodology for estimating the optimum exploitation life of machinery. The study was successfully carried out by a team of scientists engaged from and coordinated by the Department of Computer Science of the Faculty of Mining and Geology, University of Belgrade. This paper presents the key observations covering the subject problem. Keywords: Mining, Opencast exploitation, Coal, Optimization, Exploitation life, Capital machinery, Electric power industry, Dynamic programming.

Jan 1, 2003

By M. Hakala

A computer program was developed to simulate transient strains and stresses during an overcoring in the situ stress measurement. The solution is based on superpositioning of elastic stresses. The measured strains can be compared with the calculated ones to check if the measured transient behaviour is accordant with the interpreted in situ state of stress. If not, the in situ state of stress can be calculated based on any transient or final strain values. The transient stresses can be compared with the strength envelope of intact rock and thereby estimate the core damage potential. Technically, the developed code fulfilled all the objectives, and the numerical error was found to be less than 5%. The basic idea can be applied also for different overcoring probes with minor modifications and recalculation of stress tensors. The analysed case studies showed clearly the advance of having an objective and practical quality control method to study the reliability of the in situ stress measurement data. The study was set up and funded by the nuclear waste management companies Posiva Oy ( Finland ) and Svensk Kärnbränslehantering AB ( Sweden ). Un programme informatique a été développé pour simuler des tensions et des contraintes passagères pendant la mesure in situ de contrainte de surcarottage. La solution se fonde sur une superposition de contraintes élastiques. Les contraintes mesurées peuvent être comparées avec celles calculées pour vérifier si le comportement passager mesuré correspond à l'état de contrainte in situ interprété. Sinon, l'état de contrainte in situ peut être calculé à partir de n'importe quelle valeur de contrainte passagère ou finale. Les contraintes passagères peuvent être comparées avec l'enveloppe de force de roche intacte et ainsi il est possible d'évaluer le potentiel de dégâts au noyau. Techniquement le code développé a rempli tous les objectifs, et le taux d'erreur s'est révélé être inférieur à 5 %. L'idée de base peut être appliquée aussi pour différentes expériences de surcarottage avec des modifications mineures et le recalcul de tenseurs de contrainte. Les études de cas analysées ont montré clairement l'avantage d'avoir une méthode de contrôle de qualité objective et pratique pour étudier la fiabilité de données de mesure de contrainte in situ. L'étude a été fondée et financée par les sociétés de gestion de déchets nucléaires Posiva Oy (Finlande) et Svensk Kärnbränslehantering AB (Suède). Es wurde ein Computerprogramm entwickelt, um Transient-Beanspruchungen und Spannungen während eines Überentkernens in situ-Spannung-Messung zu simulieren. Die Lösung beruht auf Superpositionierung von elastischen Spannungen. Die gemessenen Beanspruchungen können mit den berechneten Daten verglichen werden, um nachzuprüfen, ob das abgemessene Transient-Verhalten mit dem interpretierten in situ-Zustand der Spannung übereinstimmt. Wenn nicht, kann der situ-Zustand der Spannung auf irgendwelchen Transient- oder endgültigen Beanspruchungswerten berechnet werden. Die Transiet-Spannungen können mit dem Stärke-Umschlag des intakten Felsens verglichen werden und dadurch ein Kernbeschädigungspotential kalkulieren. Technisch erkannte der entwickelte Code alle Ziele und hat gefunden, dass die numerische Fehler weniger als 5 % waren. Grundsätzlich können auch verschiedene Überentkernen-Untersuchungen mit kleineren Modifizierungen und Wiederberechnung des Spannung-Tensors angewandt werden. Die analysierten Fallstudien zeigten deutlich den Fortschritt, objektive und praktische Qualitätskontrollmethode zu haben, die Zuverlässigkeit in Situ-Spannung-Messung-Daten zu studieren. Die Studie wurde aufgestellt und durch Atommüll-Management-Firmen Posiva Oy (Finnland) und Svensk Kärnbränslehantering AB (Schweden) finanziert.

Jan 1, 2003

"This paper challenges the traditional notion that mine planners need to plan production so as to incur the lowest mining cost. For a given mine configuration, a mine that increases its mining rate will incur increased mining costs. In an environment in which operations are fixated on cost reduction, a proposal that increases costs will not be readily accepted. Such a proposal requires financial justification—the increase in costs might be recuperated by the additional production. This paper evaluates the net present value (NPV) across a range of copper prices for two underground orebodies located at different depths, using a production rate of 300 kt per quarter and a scenario that introduces additional equipment and costs for 450 kt per quarter. The evaluation was based on the changes of NPV for the orebody located at a shallow depth compared with the orebody at a greater depth. Discrete event simulation combined with mixed integer programming was used for analysis. Unlike traditional sensitivity analysis, this study re-optimizes the mine plan for each commodity price at each production rate. The results show that, for the low mining rate at the final copper price, an NPV of A$1530.64 million is achieved, whereas an NPV of A$1537.59 million is achieved at a higher mining rate. Even though pushing mining rates beyond traditional limits may increase mining costs, this option may be beneficial at certain commodity prices, particularly when prices are elevated. IntroductionA traditional notion among mine planners is that mining rates should be planned in such a way as to reduce production costs. This concept generally relates to the mining rate that results in the highest machine utilization for the selected equipment. Although an existing mine may consider increasing its mining rate by adding equipment to a given mine configuration, this typically increases mining costs. In an environment in which operations are fixated on cost reduction, a proposal to increase costs may be very difficult to argue for. The value of the mine plan is well recognized as varying with the mining rate for a given orebody (Smith, 1997)"

Jan 1, 2017

The heap leaching of base metal ores can be applied within a number of different scenarios, each requiring its own set of parameters to be determined during the metallurgical testwork programme. The occurrence of acid-gangue reactions and its concomitant precipitation reactions is a factor common to all cases, and requires that the optimal irrigation acid strength be found that optimises the combination of extraction kinetics, acid consumption and possible premature blinding of the heap due to precipitation reactions. For the heap bioleaching of base metal sulphide ores the oxygen requirement needs to be determined for the design of the aeration system, and the operating conditions employed need to also facilitate bacterial growth over and above the acid strength optimisation mentioned above. For the heap bioleaching of chalcopyrite, the need to preserve heat in the heap becomes yet a further parameter of critical importance. For the heap leaching of uranium ore a choice is required between either chemical or bacterial oxidation, based on economic and processing factors. Frequently the operating parameters need to be determined for a circuit in which heap leaching is combined with tank leaching and/or pressure leaching. The processing implications and metallurgical testwork approach for each case is discussed.

Jan 1, 2007

By A. Aitio

Sustainable development is one of the central themes of the work of the World Health Organization; chemical safety is one of its important components. For more than 25 years, WHO has had specialized units for assisting member countries in dealing with their problems in chemical safety. For one of the units involved, International Programme on Chemical Safety, a reorientation is in progress to make best use of existing resources, and to prioritise the work to optimally correspond to the needs of the member countries. The risk assessment work of IPCS, and specifically, the work on chromium and chromium compounds, are discussed.

Jan 1, 2004

By M. Olper

The zinc recycling is assuming more and more importance. A lot of zinc secondaries and wastes are ready to be collected and converted to zinc metal. The impurities present in these materials and the technical and economical problems that some traditional ways of treating these materials are facing, call for new technologies. The EZINEX Process, a fully hydrometallurgical process industrially proven to convert oxidised zinc bearing materials directly to zinc cathodes, is an innovative process that can deal with any kind of zinc waste/secondaries in a very powerful way. In this paper the highlights of this process will be shown and discussed to demonstrate the robustness of the process and its economic viability.

Jan 1, 2008

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents possibilities of reducing methane emission to the atmosphere in working mines in Jastrzebie Coal Company by means of proecological solution. They form a new approach towards the problem of rational and effective use of natural resources both in economical and environmental respect. Power and thermal energy for underground air conditioning in mining excavations are produced from the methane, which is drained out of the mine for safety reasons.

Jan 1, 2003

By T. Gerritsen, A. Matyas, F. Stober, I. Candy

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed. The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation.

Jan 1, 2004

By P. Sun

Abstract: From the viewpoint of interaction mechanics of solid and gas, a coupled mathematical model is presented for coal/rock mass deformation and gas leak flow in parallel deformable coal seams. Numerical simulations for the prediction of the safety range of mining of protection layer are performed with experimental data from a mine with potential danger of coal/gas outbursts. Analyses show that the numerical simulation results are consistent with the measured data on the spot. Therefore, the coupled model shows a positive future for applications in a wide range. ZUSAMMENFASSUNG:Von der Veranschaulichung der Abhängigkeit Mechaniker für Körper und Gas, wird ein verbundenes mathematisches Modell für festen coal/rock Deformation und Gasleckstelle Fluß in parallele deformable Kohlenähte dargestellt. Numerische Simulationen für die Vorhersage der Sicherheit Strecke, die Schutzschichtbergbau verwendet, werden mit experimentellen Daten von einer Grube mit möglicher Gefahr der coal/gas Ausbrüche durchgeführt. Analysen zeigen, daß die numerischen Simulation Resultate mit den gemessenen Daten bezüglich des Punktes gleichbleibend sind. Folglich zeigt das verbundene Modell eine positive Zukunft für Anwendungen in einer breiten Strecke. RÉSUMÉ: Du point de vue de la mécanique d'interaction pour le solide et le gaz, un modèle mathématique couplé est présenté pour l'écoulement plein de déformation de coal/rock et de fuite de gaz dans les filons houillers deformable parallèles. Des simulations numériques pour la prévision de la gamme de sûreté employant l'exploitation de couche de protection sont effectuées avec des données expérimentales d'une mine avec le danger potentiel des accès de coal/gas. Les analyses prouvent que les résultats numériques de simulation sont conformés aux données mesurées sur place. Par conséquent, le modèle couplé montre un futur positif pour des applications dans un éventail.

Jan 1, 2003