Search Documents

By F. T. Baker

The Primero mine, operated by the Colorado Fuel & Iron Company, is located 17 miles west of Trinidad, Colorado, in Las Animas County. Unusually bad roof conditions, along with heavy side pressure and other conditions causing rapid decay of timbers, all combine to create a very serious timbering problem. The height of the coal averages six feet six inches. It is a heavy coking coal and has a tendency to become easily crushed and broken down in the seam. The seam lies about 35 feet below the sandstone and the intervening formation is composed of loose shaly rock, and as the coal is extracted, the air slackens this rock to such an extent that within 24 hours, roof falls varying from five to fifteen feet in height are likely to occur. Under these conditions it is necessary to use cross bar sets in both rooms and entries, and they must be spaced no further apart than three and one-half foot centers, and be maintained within a distance of three feet of the face. Rooms are spaced on fifty footcenters, and cannot with safety be driven to exceed 14 feet in width, and 200 feet in length. The large pillar must be maintained to protect from side pressure, and the rooms must be driven up and retreated with as quickly as possible to avoid the squeeze caused by the intense side and roof pressure. Best results in extraction have been obtained by driving rooms for only a distance of 150 feet. Under these circumstances, it is readily seen that timbers of small diameters cannot be utilized in timbering any development work of a permanent nature. Entries are driven nine feet wide, and special peeled piling with an average diameter of 12 inches are most commonly used. It, is necessary to use lagging between each set of crossbars . Conditions such as these necessitated an immense expenditure for mine timber. In addition to ordinary seven and eight foot props, we used a yearly average of 65,000 feet of heavy peeled piling, averaging in diameter from 10 inches to 12 inches. Annual expenditures for timber of all classes was in excess of $60,000.00. Timber costs per ton averaged around 29 cents. In view of these exceptionally severe timber conditions at Primero, the company, in 1920, had a survey made with a view of providing some remedy to this problem. A comparison of the life of main entry timber at other bituminous mines was made, and an average life of four years was established. The actual data collected at Primero indicated an average of less than two years in the manway or "return" airways, and up to five years on the haulageways or "intake" airways. While some of this timber will stand up for a much longer period than this, a close inspection will reveal in most cases that its period of usefulness is spent. It is very essential when discussing the life of timber, especially that used on, main haulageways and aircourses, that a distinction be made between the point of service, that is, the point where it is sound, serviceable and able to carry weight, and the point of breakdown or failure, where it is no longer sound and able to carry weight. In figuring the life of timber, the point of service only should be considered as timber will frequently stand for a considerable length of time when it is entirely decayed and unserviceable. The larger part of the timber used for our permanent work was Alpine Fir, or what is locally termed Red Spruce, and the supply of this I is gradually becoming depleted and has to be obtained at a point so distant

Jan 1, 1926

By H. F. Nash

Coal is the basic necessity of our present-day civilization, and those engaged in the industry, whether miner, day-man, pit boss, tipple boss, superintendent, salesman or operator, have a direct responsibility to the public at large. Our country is blessed with a great supply of Bituminous coal, upon which it must largely depend for its industrial prosperity. Anthracite coal, in its relation to our economic situation, is a small factor, as its ratio of production to Bituminous coal is only about one-sixth. However, within the last ten years, electricity and oil have largely displaced the use of coal in industry, so that the use of Bituminous coal is decreasing, relatively, and the potential production of Bituminous coal has largely increased since the war. High wage scales and high freight rates make the delivered price of coal to the consumer so out of proportion to the cost of electricity and oil -and strikes make the supply of coal so uncertain-that industry is rapidly turning to electricity and oil. The energy in a ton of coal can be transported, by electric current, a distance of 250 miles for 78% of what it costs to ship the coal in bulk, by rail, in the East-and, for about 60% of what it costs in our section of the country. The use of fuel oil, distillate and gasoline, in industry, has increased by leaps and bounds. Especially was this noticeable during the strike this year, as the large packing plants in Kansas City, Omaha and Sioux City (that formerly used nothing but coal) are now practically all using oil. This also supplies to other industrial plants throughout our territory in Texas, Oklahoma, Kansas and Nebraska. Many railroads are using oil, as are also the smelters, cement plants, etc., etc. Ten years ago, 100% of the threshing in the state of Kansas was done with coal-today not over 25% of it is done through that means-and so it goes all along the line. The use of our coal is being yearly more restricted in industry. In the case of domestic consumption, the circle is also ever decreasing.' In small towns and on farms, kerosene, gasoline and wood are largely utilized for cooking. For the past four years, along any country road, it is a common occurrence to hear a buzz-saw cutting old fence posts or timbers taken from creek bottoms. Many thousands of tons of coal are displaced each year through the use of corn and cobs. In larger towns, gas plants have been installed, and many housewives use gas-in communities contiguous to natural gas, that is used for industrial and domestic purposes. The time has gone when industrial and domestic consumers or dealers are satisfied to buy anything that is black-competition among the coal-producing states is keen, and will become more so. Eastern and southern fields are turning out splendidly prepared coals of high quality, and with their lower freight rates to competitive territory, will entirely nullify the use. of our Western coal unless-

Jan 1, 1922

By Graham Bright

Up until a few years ago most of the electrical equipment used in the mines of this country was developed for industrial purposes and was adapted for use in mines by slight modifications. It became apparent, however, that mining conditions differed widely from most industrial applications and it became necessary to design and develop apparatus, particularly suited for use under mining conditions. Most of the electrical apparatus used in mines today, however, does not owe its success entirely to mining development, but in many cases developments in other branches have been taken and improved upon and modified to meet mining conditions. Power Plant: In the earlier days the power plant for the production of electric power usually consisted of fairly small belt driven direct current generators operated from reciprocating non-condensing steam engines. Today where possible the mines purchase power from central stations and where not possible it is ususally produced from turbine driven plants using non-condensing turbines for the smaller plants and condensing turbines for the larger plants. The bad water conditions at many of the coal mines in this country is, responsible in a large measure for the high cost of upkeep and repairs in isolated power plants. This feature with the type of labor available makes it difficult to operate an isolated plant condensing except in the larger mines where water conditions are good and the apparatus can be taken care of. The geared turbine is a particularly simple and rugged piece of apparatus and requires very little attention over long periods of time. Hoists: The first electric hoists to be installed used various types of motors designed for railway or industrial purposes, and the control furnished was far from satisfactory. Today most of the mine hoist motors are of the alternating current type, especially designed for hoisting service. The control for motors of 200 H. P. or over is usually of the magnetic of liquid rheostat type, and as built today will operate over fairly long periods with a very moderate cost of up-keep. Hoists of 1000 H. P. or larger are usually of the direct current type using field control and receiving power from a flywheel or synchronous M. G. set. Hoists of this type have made remarkable records in regard to continuity of operation and low cost of up-keep. Where high speed operation is desired in either coal or metal mines, the D. C. equipment using field control and a separate M. G. set to supply power to the hoist motor is not only the safest and most economical but in many cases is the only type of equipment capable of satisfactorily obtaining the output required. A number of improvements have been brought out with the field control scheme in connection with the acceleration, retardation, overfeed and overwind of the hoist. With these new developments the hoist operator can no longer abuse the hoist by improper manipulation of the control handle. Until a few years ago the matter of safety devices was not given much consideration when installing hoisting equipment. At the present time the safety devices are considered one of the most important items in connection

Jan 1, 1922

The meeting was called to order in the Albany hotel, with the President, John B. Marks, in the chair. At the request of the Secretary, the chairman brought before the Institute the question of a reorganization of the finances and system of conducting the Institute, explaining that, although the Institute is in good financial shape and the meetings are of great interest and are attended by a large and serious minded membership, the Institute is getting so large and of such value to the operators that it should be taken over by the operators, conducted by some man elected by and from the operators, and its financing put on a definite basis. At present, it was explained, the Secretary, not a coal operator nor interested in operating, arranges and conducts all meetings and finances the Institute from three sources: the very low dues, the advertisements published in the Proceedings, and by direct solicitation of contributions among the supply and machinery houses. Mr. James Dalrymple spoke vigorously on the need of having the Institute entirely free from any taint of commercialism. Upon motion by W. D. Brennan, seconded, a committee of four, one to represent each State, was voted. Appointment of this Committee was deferred temporarily. The reading of the minutes of the previous meeting was then called for, but upon statement of the Secretary, that the minutes were published in Volume 2 of the 1925 Proceedings, they were dispensed with. The Secretary-Treasurer's report was made informally inasmuch as the last report had not yet been audited. In brief, the Secretary reported on a cost of approximately $1,600.00 a year to publish and send out the Proceedings, an expense of approximately $1,800.00 to care for the Denver meeting, and an expense of approximately $1,200.00 to care for the summer meeting. The Secretary's salary of $25.00 a month has not been collected, but a certain portion of this has been used for stenographic expense. The Secretary asked for expression from the floor regarding the advisability of continuing the publication on the present elaborate plan. Mr. Gibson, Mr. Marks, Mr. Whiteside, Mr. Littlejohn, Mr. Dick and others spoke positively on the value of the present form of the Proceedings, and urged that no changes be attempted in this. Upon motion of Holbrook Mahn, it was moved, seconded and carried that E. H. Weitzel and W. F. Murray be made life members of the Institute in recognition of their services in the organization of the Institute, placing them with Floyd W. Parsons as the original organizers of the Institute. Mr. Murray spoke briefly in acknowledgment of the courtesy. Mr. Weitzel's words are included in the discussion A letter was read from George B. Pryde relative to the present emblem of the Institute. Upon motion by Mr. C. W. Sinclair, seconded by Mr. Dalrymple, it was moved that the consideration of a new emblem be

Jan 1, 1926

By Charles Gottschalk

Some time after my arrival in Rock Springs to fill a short engagement with The Union Pacific Coal Company, Mr. Dickinson informed me that he had placed me on the program for a paper entitled "Mechanical Loading in Indiana." Since development of mechanical loading operations on a genuine coal producing basis for that section began near Oakland City, Indiana, and rapidly spread over Southern Indiana, Western Kentucky and Southern Illinois simultaneously, the results referred to are in many ways common to all three states. Prior to December, 1922, several attempts at mechanical loading had been registered, notably among which were installations of the Jeffry Entry Driver, and the Meyers-Whaley loader. The object of most of these earlier installations was quick development rather than lower production costs in face loading. In this measure it is claimed the machines were at least partially satisfactory. Three items which seemed to delay rapid progress in the adoption of either machine were, excessive first cost, height of coal seam necessary, and timidity of the operator relative to the labor situation which might develop. When the Joy machine was put on the market in the form of the 4-B.U., with a clearance overall which would perform in coal slightly under five feet in height, and at a cost price of less than one-half that of other machines being sold, many operators were at once ready to take a chance along with the manufacturer. This desire was accentuated by the difficulty to operate coal mines at all at prevailing production costs. This condition also made the coal miner more receptive to machinery which would give added employment to the field. At the convention held in Cincinnati during May, Mr. .Joy stated that about 200 of his machines were in operation at that time. Mr. Whaley said that about 40 of his were in use in coal mines. It is probable that of the above sum 75 machines were installed in Indiana, Illinois and Kentucky. Since that time, possibly 50 more machines of later design have been added. Like many of our troubles, those which seemed most difficult to overcome, proved in the end to have been least of all, and in this case the sup¬posed resistance which labor would advance has been more or less imaginary. In Illinois and Indiana a scale of wages is being accepted which is consistent with average earnings of machine men. The fact that a large number of coal operators want and are buying more loading machines has encouraged mining machinery manufcturers on every hand to devote renewed vigor to the cause and it is generally understood that new types and models are being developed both in factories and mines with the coal industry eager always to see the latest development. I understand that at present the Goodman, the Jeffry, and the Sullivan machinery companies are each offering new designs to meet Indiana and Illinois requirements. It is not strange that with so many installations many were made as a result of an impulse to ride the band wagon without any serious attempt to study the results or draw any conclusions from the experiences of others with loading machinery.

Jan 1, 1924

By D. Harrington

My acquaintance with rock, dusting as a preventive of wide spread explosions in coal mines dates from the fall of 1914 and the spring, summer and fall of 19.1.5 when I had an opportunity to observe the staging (both before and after) of several of the explosions in the Experimental Mine at Pittsburgh and saw violent explosions stopped by rock dust, also saw violently explosive coal dust made insensitive by use of rock dust to ignition or to propagation or spreading of an explosion. From this work I became a convert to rock dusting though I had previously been a firm believer in watering methods and am yet a firm believer that watering, methods have a well defined place in promoting the health and safety of our coal miners. In 1916, while in the Bureau of Mines service, I made an underground study and a report to the Bureau on the first extensively rock dusted mine, in the United States, the Delagua Mine of the Victor American Fuel Company near Trinidad, Colorado, there being then some ten miles of entry in that mine which had been kept well rock-dusted for at' least four years The dust used was " adobe" or surface soil screened from sweepings of the dry surface wagon roads through a screen with one-eighth inch openings, the dust giving about 20% through 200 mesh and about, 10% of approximately 1/8-inch size. The material was collected during dry weather by contract at $1.00 per ton (sacked) and was accumulated in summer and stored for winter and spring use. The dust was scattered through haulage entries by hand or by an electrically operated blower and was held on shelves along the ribs or between and on timber caps with from 1/4-inch to 2-inch thickness of the rock dust. The cost of maintaining the 10 miles of entry well dusted was about $1,500.00 per year or $150.00 per mile per year. Total cost of 'the rock dusting over a four-year period was about $6,000.00, about 2,500 tons of dust being used and 2,000,000 tons of coal produced; the above cost included about 1,200 days labor dusting at $2.50 per day, 2,500 tons of rock dust at $1.00. per ton and miscellaneous labor, material, repairs, power cost, etc., amounting to about $500.00. The cost per ton of coal produced for keeping 10 miles of entry rock dusted being about 3/10c. In addition to the rock dusting, some sprinkling was done, chiefly in the interior of the mine, costing about 2/5c per ton; and due to spilling of coal and sifting of coal .dust through loose cars on the entry floors, the floors of haulage roads were kept sprinkled between and just outside-the rails. Total cost of sprinkling and rock dusting was about .7/10c per ton much less of course than the same work would now cost. Between January, 1916, and July, 1924, my duties in the Bureau of Mines allowed me, to follow up and make underground inspections and reports on more than 20 coal mine explosions and fires in a number of states of the union and in this work a large number of samples of road, rib, and other dusts were taken to ascertain the effect of moisture, roof and floor dirt, etc., upon the propagation or the stopping of the explosion; also a large part of my work was to obtain evidence pro and con as to influences affecting the disasters and very prominent among those influences were the occurrence or use of water, water drippers, or ponds, as well as of sand, roof or floor rock or dust on floor, ribs, etc. The Dolomite explosion near Birmingham, Alabama, in November, 1922, and the Dawson No. 1 Mine Explosion at Dawson, New Mexico, in February, 1923 (at both of which I made underground inspection and report) both starting on main intake haulage road and both in mines which had fairly elaborate watering systems, convinced me that at least as far as freezing can occur on main intake air courses which also act 2s main .haulage ways, rock dusting is likely to be much more dependable than sprinkling. In making up the report on the Dawson Explosion to the Bureau of Mines (copy of which also

Jan 1, 1925

On Monday, June 27, 1921, at 6 p. m., twenty-four members of the Institute from. Colorado and New Mexico, left Denver on the Union Pacific for Rock Springs, Wyoming, arriving there at 9:42 a. m., June 28th. The party was met at the depot by the Rock Springs committee and a large number of the local Institute members. The day was spent in visiting the Central Power Plant of, the Union Pacific Coal Company and adjacent mine, the new 'E Plane, the Reliance, Dines, Winton and Sweetwater coal properties in the district. At noon a very elaborate lunch was served in the First Aid Building at the Reliance mine, which was most heartily enjoyed by all. In the evening the members and friends visited the new Rialto theater and saw the pictorial exposition of the' "Sky Pilot". The evening terminated with a dance in the ballroom of the Masonic Temple from 9:30 until midnight, concluding one of the most enjoyable days which the Institute has ever spent in Rock Springs. At 12:3o a. m. the original party, augmented by six members from Rock Springs, were again enroute to Salt Lake City, arriving there at 8:30 in the morning of Wednesday, June 29th. The Hotel Utah had been selected by the local, committee as the headquarters for the convention, and the majority of the -members at once proceeded to that place where the books were opened and the paying of dues and registration of the members were carried on until 11:45 a.m. At noon a majority of the members were entertained at the L. D. S. Tabernacle with an organ recital, which was up to its usual standard of excellence.

Jan 1, 1921

By B. W. Dyer

At about 8:30 o'clock on the morning of March 8, 1924, an explosion occurred in the Castle Gate No. 2 Mine of the Utah Fuel Company, Castle Gate, Utah, and 171 men lost their lives. The explosion was caused by the ignition of a comparatively small body of gas and was propagated throughout the mine by fine coal dust which had accumulated on the roof and ribs of the mine and by coal dust made by the explosion itself. Castle Gate No. 2 Mine was one of the best kept mines in the state and it was believed not only by the officials of the Utah Fuel Company, but by all others connected with the coal industry of the state that this was one of the safest mines in the entire state. The state had not been visited by a catastrophe for over twenty years and it was a general belief that the mines were kept in such condition that a catastrophe was almost impossible. During the preceding twenty years new mining officials from other fields had entered the state and seeing that sprinkling as done in Utah was far more elaborate than in most other coal mining sections of the country, caused them to believe that they were keeping their mines in an absolutely safe condition. When coal -mines suffer no mishap during a period of twenty years the general attitude relative to safety may become somewhat lax, not only with the operating officials, but also with the State Inspection Department. However, there were some who were more keen to appreciate the hazards of Utah coal dust and who predicted that if Utah mines were kept only damp but not wet, some day the state would be shocked by the news of a dreadful disaster. In a paper prepared and read before the Salt Lake City Chapter of the American Institute of Mining and Metallurgical Engineers in 1924, Mr. D. Harrington stated: "The writer had his first mining work in Utah mines spending nearly ten years in Utah, starting just after the Scofield explosion in 1900. After having been absent from the state for about eight years upon returning and spending a few days in a few properties, there appeared then to be a definite relaxation as to precautionary methods especially against dust; some of the properties which in 1900 to 1910 would have stopped work if for any reason water was not available for sprinkling purposes, were in 1918 definitely dry in many places, and in some instances there was also definite relaxation as to shooting regulations, some properties with electric shooting systems were allowing firing of certain shots while the men were in the mine. The Utah coal. dusts are too inflammable and explosive to allow of taking any chances and unless up-to-date and carefully maintained, the Utah coal mining world will hear to its dismay, that the very excellent record of the past twenty-three years as to explosions has been shattered. Hence, possibly it was not altogether a complete surprise that such a disaster occurred in Utah, but it was a surprise to many that it occurred in one of the best kept mines in the state and it was that fact that led the coal mining men of Utah to believe that the state coal mining laws should be modified.

Jan 1, 1925

By D. Harrington

At the time of mine accidents one frequently hears the expression "there will be accidents as long as there are mines", or it may be varied to state that the accident in question was unavoidable, or something similar indicating inability to prevent accidents. However, it is the opinion of the writer, after over twenty-one years experience in both coal and metal mining, seven years being spent wholly in safety work, that by far the greater number of all accidents is due to carelessness or negligence. This carelessness or negligence may be on part of the victim of the accident or of one of his companions, or on part of his employer or possibly even of the inspector or safety man, and in some cases all of these agencies are involved. It manifests itself in various guises, one of the most serious being violation of state mining laws or regulations or of mine rules, and frequently the rules of ordinary common-sense. The cause very frequently is that trait in human nature to "take a chance" and it has been the writer's observation that the worst offender is the old-time miner who has come safely through many years experience, who was mining when the "safety man was a baby", and who clings to old-time ideas and practices and has "no use" for "newfangled" present-day "notions". Unquestionably, there are accidents, wholly unavoidable and many are caused by ignorance and by the new-comer in mining, yet as previously indicated, the writer's observation is that the old-timer is by far the worst offender, bringing grief to himself, companions and employer. Of the numerous manifestations of carelessness and negligence in connection with mine accidents, which have come to the notice of the writer, only one will be treated in this paper, viz: Violation of State Mining Law, and mention will be made only of explosions and major accidents in coal' mines with which the writer came in personal contact as investigator. In most cases, in addition to mine inspection after the accident, the writer heard the evidence given at Coroner's inquest and thus was enabled to for¬mulate fairly definite impressions as to events and conditions leading up to the occurrence.

Jan 1, 1922

Earl W. Baker W. P. Bigler Lyman Fearn Leslie H. Johnson V. O. Murray Max C. Scheble Fred L. Smith who left the world better for their having lived in it . . .

Jan 1, 1986

Kenneth M. Payne RMCMI PRESIDENT 1994-1995 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 91st Regular Meeting and Convention to be held June 25 thru 27, 1995 Crested Butte, Colorado

Jan 1, 1994

The thirty-first regular meeting of the Rocky Mountain Coal Mining Institute was called to order at 11: 10 o'clock A. M., Wednesday, June 22nd, 1932, President T. H. Butler presiding. The Honorable Louis Marcus, Mayor of Salt Lake City, delivered the address of welcome. On motion of W. H. Bachman and seconded by D. J. Parker, it was voted that, inasmuch as the Minutes are printed in the annual bulletin, the reading of them be dispensed with. The President made his annual report. The Secretary-Treasurer made his annual report of the financial condition of the Institute. R. Dawson Hall addressed the meeting. The following committees were appointed by the President: Auditing-L. P. Pearce, Chairman; Joseph, Parmley, R. R. Knill. Nominating John Emrick, Chairman; D. J. Parker, John Marks. Resolutions-D. R. Wilson, Chairman; H. Petersen, Robert Williams, Jr. There being no further business to come before the meeting, the same was adjourned at 11: 55 o'clock A. M.

Jan 1, 1932

Jan 1, 1953

By Eugene McAuliffe

The labor turn-over at coal mines has long been a fertile subject for parade by complaining coal operators, the question invariably occupying a place of prominence in the list of disabilities that tend to increase the cost of producing coal, adding likewise to the now startling number of accidents that occur in coal mines. This disability, however, is like the weather question, which some humorist once remarked of by saying, "The weather is something we all talk about, but nobody does anything to improve it." Endless compilations covering the shift of employment by coal mine labor have been made and published, and while the actual loss expressed in cents per ton in cost of coal produced has never been determined, the fact remains that such represents a substantial item, taking the mines of the country as a whole. Efficiency engineers who have made studies covering the cost of breaking in and training each new man employed in certain manufacturing industries, fix same as averaging not less than $100.00 per man, and when the character of mine employment is given due consideration, including its ever-present hazards, the difficulty of close personal super- vision of individual employes, and the, at times, almost impossible ability to transmit to men of many diverse nationalities understandable instructions, it is quite safe to say that the cost of securing and breaking in new men for underground mine work will fully equal that suffered by the factory managements. When we speak of mine labor turnover we must necessarily exclude the enforced shifting about of men who are laid off by the closure of mines due to accident or lack of market, con- fining ourselves to the turn-over occasioned by- (a) the dismissal of individual men or groups of men; (b) the voluntary resignation of the individual workman. It is these two methods of severance that the employer and employe alike suffer from; the item "Unclaimed Wages" carried in the accounts of every large coal company illustrative of the "quit this job, get another one" attitude of many workmen, who frequently, when leaving, fail to claim small sums due them, while others, in turn, leave a train of debts, large and small, behind. There is' ample evidence abroad to the effect that many

Jan 1, 1925

By J. F. McDermott

The problem of converting our raw coal, and especially those coals that are not suited for long storage, in other words soft, into a fuel which would be at once clean; of a high B. t, u. content and low ash, is one that has occupied the minds of many able chemical engineers and hydrocarbon technologists during the past few years. Low temperature carbonization is the present outcome of this line of research, and many methods have been evolved of recent years to turn out a serviceable, useful fuel, and at the same time, save the by-products. As most of the research and data within my experience and knowledge pertains to lignite or sub-bituminous coals, I will confine my remarks to coals of that character and grade: I might say that Colorado coals, commonly called lignite, are not in reality true lignite, but are sub-bituminous, although I have in my possession an analysis of a Colorado coal which shows a moisture of 17 per cent, volatile 31.5 per cent, fixed carbon 28.8 per cent, and an ash of 22.7 per cent, and B. t. u. less than 8,000. Even this, though useless for domestic or indeed industrial purposes, could not be classified as true lignite. However, for the purposes of this paper I will refer to these coals as lignite. Two thousand pounds, or one ton, of raw lignite carries about 20 per cent moisture. This, of course, varies in some coals, but is, I believe, a fair average. For carbonization purposes this is usually dried to a 5 per cent moisture, therefore leaving but 1,700 pounds of coal to be placed in the retort. From present knowledge, and with the average process of carbonization, 70 per cent of this coal will come out carbonized, or 1,190 pounds, to which is added about 10 per cent pitch, which is fried out as the coal passes through the retort, and which is used as a binder, making a total of 1,360 pounds of coke or carbonized coal. This is usually in appearance a dark colored, rather porous coke of about the size of pea coal. It burns without smoke and have a very high B. t. u. content. According to most authorities on this subject, carbon, hydrogen, oxygen, nitrogen, sulphur and ash constitute the only elements on which carbonization value of a coal depends, and of these hydrogen is the most important. It is claimed the value of a coal for carbonization purposes may be roughly surmised from the hydrogen content. If this is promising, that is, showing an available hydrogen content of from 3 to 5 per cent, the coal should be given a careful ultimate analysis. Should the seam, as often happens in lignite coals, show varying bands of coal of different structure or appearance, samples should be taken from each band as well as a gross sample taken down the face of the seam in the usual way. This is in order to determine what part of the seam is most promising for by-product processes. A seam showing a high nitrogen content adds to the attractiveness of the coal in carbonizing as; if available nitrogen is 2 per cent or better, it should give a very high ammonia yield.

Jan 1, 1923

By S. W. Farnham

Those who remember the years of patient effort and the slow results obtained in the first introduction of electrical coal cutters and locomotives will, I think, admit that mechanical loading of coal is unquestionably being established at a much more rapid rate than any previous application of machinery to reduce manual labor in mines. There are many operators who consider the progress of the loaders today as slow, but considering the number of years it took to thoroughly establish electrical coal cutters and locomotives, and comparing it with the short time that the mechanical loader has been on the market, and the results that have been obtained today, they will admit, I think, that the progress of the latter is much more rapid. It is about 35 years since the advent of the electrical coal cutter and electric locomotive. Their use has brought about these improved conditions, increased tonnage per mine and other features, which are of assistance to the installation of mechanical loaders. The management and the technical staff in practically all of the American mines are trained in the use of electrical machinery and understand its operation, care and maintenance. . There is frequently, a surplus of electrical power and wiring available to take care of the small requirements of the electrical loader. The mechanical loader, therefore, starts today with the ground prepared for it. Those manufacturing companies who have had years of experience in the design and construction of mining machinery, know in a large measure what to incorporate in their designs to make the parts of the new type of machine effectively strong and to operate with efficiency under the severe conditions encountered in mining service. All these advantages greatly assist the success of a new type of machine such as the mechanical loader. In spite of these advantages, however, there are bound to be some failures. All new types of loaders have to be developed. We hear of some that are a success and some that are set aside. The field of application of each type and its limitations first must be determined by actual operation. The earlier loaders had to be changed and improved in design as weaknesses developed. Not all of the new types of coal loaders have been built by mining machinery manufacturers of long experience, and the lack of experience in this line is responsible for some of the early failures. The coal mining company staffs and also those of the loader companies had to learn what the operating factors were that made mechanical loading a success. The difference in results obtained by loaders in different properties under similar physical conditions indicates that the mine management is a very large, if not the major factor, affecting the efficiency of mechanical loading. Many articles have been written on the question of loading. The subject has been quite fully discussed at recent coal meetings and in the technical press. It is not always as easy or simple a matter to form conclusions as may first appear as to one's own particular loading problem. Mechanical loading is a comparatively new art, and many companies while claiming that loaders are quite successful, do not have an accurate line on the actual saving they are affecting. Many of them have only a few of the factors taken into account in their costs. Many loaders have been generally bought without very careful consideration given to all details and except where extremely favorable conditions prevail, failure resulted. When contemplating the installation of mechanical loading, one naturally desires to select the type of loader that will, fit his mining conditions. The things

Jan 1, 1924

Past President Shirl McArthur opened the meeting at 9:30 a.m. He called on the Auditing Committee to give its report. Stan Shubart, who checked the financia1 report of the treasurer, read the report. He asked that it be approved. A motion was made, seconded and carried. Shirl thanked all the committees for an excellent job in making this meeting a most successful one. Special thanks to Park Lamborn for a fine program and to Gussie Whiteside for all her efforts in behalf of the Institute. An increase in salary was voted for the secretary-treasurer. It was decided to return to Vail for the 1979 convention. The Resolutions Committee was called upon to give its report. Roy Coulson, Chairman, submitted the following: (I) RESOLVED, Whereas, in the year since the last convention of The Rocky Mountain Coal Mining Institute, the Institute and the coal mining industry have suffered the loss through death of the services of: O. F. Bridwell C. L. Book O. F. Lewis Frank Kolar O. H. Littrell L. B. Phillippi Weston L. Potter George C. Trevorrow

Jan 1, 1978

Our presiding officer for this session is someone we are all proud to be associated with. One who is dedicated to Public Service and Safety in the State of Colorado, and known in the mining field and the Colorado Mining Association. We are very pleased to introduce Mr. Donald Haske, Chief Mine Inspector for the State of Colorado: Donald Haske: Officers, Members and guests. It is certainly my pleasure to be here today and an extra special pleasure to be presiding over this session. As some of you know, from natural up, heavy equipment is rapidly coming to the field of mining. This may seem a long way off at the present, but it certainly isn't. We are getting all the old annuals (Bi) together to be compiled for a guide and public attraction. However, we are unable to locate an (1894 panel). If any of you know of any of these please let us know.

Jan 1, 1967

Past President Ralph Moore opended the meeting at 9:30 a.m. He thanked all the committees for their part in making the 1977 meeting the success is was. He then turned the meeting over to President-elect, Shirl McArthur. President McArthur called on the Auditing Committee to present its report. Gabe Ishley, Chairman, read the report and asked that it be approved. A motion was made, seconded and carried. Loren Linville gave his report on registration and new members which figures are in the Monday a.m. business meeting of the Proceedings. The Resolutions Committee was asked to give its report. William Bear, Chairman, submitted the following: (1) RESOLVED: WHEREAS, in the year since the last convention of The Rocky Mountain Coal Mining Institute, the Institute and the coal mining industry have suffered the loss through death of the services of: John A. Garcia John B. Huehes H. B. Lindeman Richard B. Miller Charles Pliley Wilford Ruff James Westfield

Jan 1, 1977

By James F. Howe

Modern civilization is centered around a small group of essential occupations, the three principal ones which are agriculture, mining and manufacturing. Agriculture might be called the most important of the three, as it has to do directly with the supply of food for the human race. Mining, however, is certainly next in importance, as it furnishes the supply of fuel and many of the raw materials used in manufacturing. Without mining, modern machinery and many industrial operations would be impossible. Mining takes advantage of the, natural resources in fuel and minerals that lie underneath the surface of mother earth, and while at times some of these metals are hard to find and mines come and go, mining must continue to increase. Mining is no longer a haphazard proposition but one calling for careful study and complete plans of operation for years to come. The shafts, power houses, rock dump crusher, concentrator, and other machinery must be located advantageously in order to enable owners to make a profit. Many tons of rock or mineral must be mined frequently to get one ton of concentrated metallic ore or metal itself. Economy in mining is just as essential as it is in manufacturing. The mining engineer of today is called upon to utilize every branch of engineering, and not only, is a wide: range of knowledge required, but ingenuity to meet the unusual conditions which are constantly arising from week to week. On account of the wide variety of information required by the mining engineer, some things with which he is in almost daily contact may be passed over with only a small amount of attention, provided everything is going well, in order that time and attention may be focused on what might be termed the more important features of mining operations. Because competition has become keener than ever, owing to overproduction at times of certain minerals, it becomes a matter of first, importance to understand as far as possible the factors which enter into the cost of production of any mineral which may be mined. In such times of overproduction, the high cost mine is forced to close down while the low cost mine may, if desired, be kept running constantly. In keeping a cost record, wire rope on account of its high first cost 19 coming into the lime light, and a comparison of records of one mine with another is now frequently made in order to see whether the rope service is satisfactory or not. Every rope maker, on the other hand, is interested in seeing that the rope which he produces gives the maximum possible return for the money invested. Modern mining owes much of its success to the use of wire rope for hoisting materials from beneath the surface of the ground. Deep mining would be impossible without the use of wire rope as a means of hoisting. A study, therefore, of rope problems in mining work and a discussion of the points which are beneficial to maximum life will enable the mining engineer, manager, or superintendent to keep his costs down to the minimum while at the same time he provides a suitable and sufficient safety factor for operations at all times. Mining might be defined as the extraction of coal, metallic ores, or minerals from below the surface of the ground. This definition does not cover what is known as, open pit operations or quarrying but covers the

Jan 1, 1922