Search Documents

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By GEORGE S. POPE

This bulletin is the third of a series a showing the results of ment purchases of coal according to specifications as to its quality and giving typical forms of proposals for supplying coal and general information relating to government coal purchases . Numerous calls for authentic information concerning the purchase of coal according to its heat value attest a growing interest in the subject. Many of the commodities of life have long been purchased according to specifications requiring chemical or physical tests , or both, to determine whether the material delivered meets the requirements , the price to be paid depending on the results of the tests . Until recent years coal consumers purchased coal merely on the statement of the dealer as to its quality , relying on his integrity and on the reputation of the mine or district from which the coal was obtained. It is surprising that the important question whether value was being received for the money expended was not sooner seriously considered . The purchase of coal by specification is an important step toward the conservation of our national mineral resources , for it results in an increased use of the lower grades of coal. The poorer coals find a market by competing with the better grades , not as to the price per ton but as to the cost of an equal number of heat units. This paper gives in detail the results of government purchases of coal for the fiscal year 1908–9 and the list of contracts with abstracts of specifications for the fiscal year 1909–10 , and summarizes the information on this subject obtained by the Survey. It is hoped that this information will promote a better understanding of the specification method of purchasing coal and furnish data valuable alike to coal dealers and coal consumers , so that equitable contracts can be more readily made.

Jan 1, 1910

Since its creation in 1910, the Department of the Interior's Bureau of Mines has pioneered in the development of mineral technology, through research. From the very beginning, research on mine health and safety has been a dominating concern, and a responsibility that expanded markedly as a result of the Coal Mine Health and Safety Act of 1969. Until the mid-1970's research on fuel technology and coal production also was an important part of the Bureau's work. But in the four years following the 1973 oil crisis, Congress established a reorganized Federal energy research apparatus in which all fossil fuel research-encompassing extraction, use, and conservation-was centralized. Today, the Department of Energy houses Federal research on coal mine production technology, while research on coal and noncoal mine health and safety and environmental technology, and on noncoal mine production technology, remains in the Interior Department as a continuing responsibility of the Bureau of Mines. In carrying out its authorized research programs, the Bureau conducts both short- and long-term re-

Jan 1, 2012

By Christopher Mark

This proceedings volume contains papers presented at technology transfer seminars sponsored by the National Institute for Occupational Safety and Health (NIOSH) on New Technology for Ground Control in Retreat Mining. The seminars were conducted at five locations: Uniontown, PA (March 26, 1997), Norton, VA (April 8, 1997), Pikeville, KY (April 10, 1997), Charleston, WV (April 17, 1997), and Evansville, IN (April 22, 1997). The papers presented here describe several new, highly practical technologies developed by the NIOSH Pittsburgh and Spokane Research Centers3 to improve safety during pillar retreat operations. Two central issues are addressed: pillar design and mobile roof supports (MRS's). Proper pillar sizing is essential for safe pillar extraction. The Analysis of Retreat Mining Pillar Stability (ARMPS) program and its large data base of actual mining case histories are presented. LAMODEL, a second computer program, can be used for analysis of multiple-seam and other complex mining situations. Other papers address pillar design to avoid massive pillar collapses and the proper role of coal strength testing. MRS's have greatly improved safety where they are used for pillar line support. We studied the application of MRS's at 20 mines throughout the Eastern United States. Conclusions regarding the most effective section layouts, cut sequences, and support placements are reported. Field and laboratory tests of MRS's are also described.

Jan 1, 1997

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, rooting granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of rooting, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural tines available. On the other hand, California manufacturers of asphalt products other than having utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, and other nonmetallic minerals as filler, mainly for reeling and flooring. Also about 500,000 tons of roofing, granules is produced in California, most of which goes into roofing manufacture in California. In addition. A significantly large and growing tonnage of relatively coarse mineral aggregates Ire used on low-angle, built-up, asphalt roofs to produce in attractive surface and offer protection against the clements. Clearly ill minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of those commodities could be utilized in some use categories.

Jan 1, 1966

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an exten- sion of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, how- ever, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's pro- duction facilities are maintaining a satisfactory quality control.

Oct 1, 1965

By Ellis S. Hertzog

The relatively large amount of phosphorous occurring in many iron ores limits their usefulness aid sometimes renders them valueless under present conditions of nip-iron manufacture. A practical method for removing the phosphorus would be valuable to the iron and steel industry. Gravity concentration has been of little value as far as the removal of phosphorous is concerned, because the compounds of this element are, as a rule, disseminated very finely. Removal of the phosphorous by leaching is not a new idea and has been the subject of some investigation,3,4/ out for data :lave been published. W.R. Crane published analyse of various ore bodies in the Birmingham ham district. The hard or unleached ores a .re much higher in phosphorous than the Soft, leached ores along the outcrops. This fact indicates that as mild a leaching agent as water removes phosphorus effectively if enough time is allowed for it to react. As the forms in which phosphorous occurs in the iron ores are important in the consideration of any leaching operation, much time was expended in devising a method for determining them. According to Professor McVey, University of Alabama, the phosphorous-bearing minerals in the red iron ores of Alabama have not been positively identified by any microscopic methods.

Jan 1, 1935

By Ellis S. Hertzog

[The relatively large amount of phosphorous occurring in many iron ores limits their usefulness mid sometimes renders them valueless under present conditions of pig-iron manufacture. A practical method for removing the phosphorus would be valuable to the iron and steel industry. Gravity concentration has been of little value as far as the removal it of phosphorous is concerned, because the compounds of this element are, as a rule, disseminated very finely. Removal of the phosphorous by leaching is not a new idea and has been the subject of some investigation,3,4/ but few data have been published. W. R. Crane published analyses of various ore bodies in the Birmingham district. The hard or unleached ores are much higher or in phosphorus than the soft, leached ores along the outcrops. Tips fact indicates that as mild a leaching agent as water removes phosphorus effectively if enough time is allowed for it to react.]

Jan 1, 1935

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By P. A. Hendricks

This U.S. Bureau of Mines (USBM) report identifies and evaluates factors responsible for metal/nonmetal (M/NM) underground mining accidents involving mobile equipment. Information regarding the occurrence and severity of the accidents, the type of equipment involved, the primary and contributing causes, and preventive measures is included. The goal of this report is to provide information that will aid mine operators and safety managers in the recognition of hazards associated with operating mobile mining equipment in an underground mining environment.

Jan 1, 1994

By James Westfield

This publication covers the work of the Division of Coal Mine Inspection, Bureau of Mines, as performed under provisions of the Federal Coal Mine Safety Act. It presents background information and data since 1952 when the Act became effective and includes up-to-date statistics for the calendar year 1962. During that year, approximately 9,704 coal mines were active in the United States, and the Bureau made 12,810 regular inspections. BACKGROUND The Federal coal-mine inspection program was established to carry out the provisions in Public Law 49, 77th Congress, (H. R. 2082) approved May 7, 1941. This act has since been amended as Title I, Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also included Title II, Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal Mine Safety Act.

Jan 1, 1963

By Wilbert J. Huff

The organization of the Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely ant accurately many previously published limits.

Jan 1, 1938

By E. O. Binyone

"https://www.youtube.com/watch?v=PBPyGXjlBHIhttps://www.youtube.com/watch?v=3AbtiKOYg7Y&feature=push-fr&attr_tag=uKtVW3yq2ZngptnE%3A6https://www.youtube.com/watch?v=PR2THayf-N8https://www.youtube.com/watch?v=mF-BXiWocqIhttps://www.youtube.com/watch?v=TuesIw-OZA4https://www.youtube.com/watch?v=v2HP7sTIZgEhttps://www.youtube.com/watch?v=v2HP7sTIZgEINTRODUCTIONIn 1937 the Eureka Corporation, Ltd., of Canada obtained a lease on the mining property of the Richmond-Euroka Mining Co. in the Eureka mining district, Eureka County, Nevada. In 1910 the Richmond-Eureka Co. suspended all operations except small-scale leasing, but company and other geologists contended that the El Dorado dolomite would also carry ore in its continuation from fault block north and northeast of the productive old working. The company began to explore the fault block in 1923 by diamond drilling from the,900 level of the Locan shaft, but for various reasons the hole was drilled to a depth of only 2 feet and was then abandoned. Eureka Corporation, Ltd., planned an extensive diamond-drilling program, which included four deep diamond-drill holes, one designated ""A"" fig. if it is to be drilled from the surfaced, and three designated ""E"", ""C"" and ""D"" figs land to be drilled from the 900 level of the Locan shaft. Of these only B and C were completed by the company. Hole C was a contribution,of the hole started by the, started by the Richmond Eureka Co. The site for hole D (figs. 1 and 2) was prepared, but the hole was not drilled. Both B and C holes penetrated sulfide ore carrying good percentages of zinc, lead, gold, and silver. The ore bodies were 40 feet thick and were found approximately 1,400 feet below the 900 level of Locan shaft.On the basis of the very favorable results obtained from the drilling program, the Eureka Corporation planned extensive development of the property and in 1942 commenced sinking the Fad shaft (figs. 1 and 2). The shortage of equipment and materials brought on by the war and difficulties with water in the shaft greatly hindered progress. However, early in 1943 the Eureka Cor¬poration, Ltd., of Canada submitted to the War Production Board a proposal for developing the mine and milling 500 tons of zinc-lead ore a day. The proposal involved an expenditure of $2,890,750."

Dec 1, 1946

By Gill Montgomery

This report covers operations at the Crystal-Victory and Minerva No. 1 mines in Hardin County, Ill., which are operated by the Minerva Oil Co., Fluorspar Division, with offices in Eldorado. It describes the exploration, development, and mining practices, giving costs of each. Transportation, equipment, power, labor, and other influencing factors also are discussed. The mining methods employed are those most applicable to the flat-bedded replacement deposits common to the Cave-in-Rock section of the Southern Illinois fluorspar district. The fluorspar beds occur from surface exposures to 1,000 feet deep. In this district churn drilling is the method practiced for exploring flat-bedded deposits from the surface. Aerial photography and geochemical methods for indicating mineralization have been helpful in planning a drilling program. A program usually includes enough drilling to obtain only sufficient data on the value of the ore body and its structure to justify initial development and purchase of the mineral rights under option.

Jan 1, 1960

By Harry E. Brownlow

The United States Bureau of Mines contracted Norecol to prepare a report identifying the regulatory processes associated with metal mine development in British Columbia using the Snip Mine as a case study. The intent of this study is to assist industry and regulatory agencies in developing understanding as to differences in objectives, perspectives and operating methods. The case study will be incorporated into a larger report summarizing the comparative advantages and disadvantages of metal mine permitting in British Columbia and Alaska. The purpose of the report is to identify the development schedule and permitting process at Snip which will assist the U.S. Bureau of Mines in suggesting improvements in environmental review and permitting processes for mine developments. The report provides an abstract of the environmental assessment review processes in Canada and the Mine Development Review Process in British Columbia and provides an understanding of the linkages between policy, legislation, and environmental review.

Jan 1, 1992

By Frank E. Cash

Published or available data on safety in quarries are few except those pertaining to blasting issued by manufacturers of explosives. During the past 25 years the quarrying industry (including various types of quarries producing many different materials) has had a markedly improved accident experience. The downward trend has not been phenomenal or has it been uniform from year to year, owing to occasional major disasters; but from the information at hand it appears that improvement during the 25-year period has been definite.

Jan 1, 1941

The panic bars (and associated linkage's and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on Self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and soma commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By E. C. Fitch

This report discusses fire-resistant hydraulic fluid safety from three different directions. First, results of a survey prepared for the Fire Resistant Hydraulics Journal by the staff of the Fluid Power Research Center are analyzed. Second, operational limitations of fire-resistant hydraulic fluids are examined. Finally, laws and standards of various foreign countries are investigated. Three conclusions are derived from a close study of fire-resistant hydraulic fluid safety from these three directions. First, a significant number of experts in the fluid power industry are no in agreement about aspects of fire-resistant hydraulic fluid fire-resistance and toxicity. This indicates a need for more in depth research. Second, the use of fire-resistant hydraulic fluids involves a compromise between the decreased fire hazards and increased toxicity and machine incompatibility problems. Finlly, major foreign governmental agencies have thorough laws and standards concerning fire-resistant hydraulic fluids. These laws and standards may provide a solid framework for further international research into fire-resistant hydraulic fluid safety.

Jan 1, 1979

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures area discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of mining modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mine is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964