Search Documents

By F. W. Lee

Operating engineers and mining executives are interested in the science of applied geophysics, but are looking for a simple and understandable exposition of its problems, instead of dissertations which are becoming more and more involved and increasingly difficult to comprehend. It may be well to discuss the goal, the attempted methods of reaching it and the psychological motive, if any, tack of the science. Where does the subject of applied geophysics stand from the viewpoint of (1) the physicist, (2) the mathematician, and (3) the geologist? Fundamentally, the science aims at a differentiation of subterranean geology with the object of finding useful mineral products by the study of gravitational, magnetic, seismic, electric, and other fields which may be associated with the materials naturally or which may be applied to them. The more skillfully these fields are recognized, applied, and analyzed the greater will be the possibility of interpreting results in a way that will be remunerative both economically and scientifically.

Oct 1, 1931

By Thomas V. Falkie, R. Venkataramani

Hand portable truck axle scales were purchased from the Martin¬Decker Company, Santa Ana, California, for weighing the rubber-tired mine shuttle cars. The scales consisted of two hydraulic load-pads, measuring 4" thick, and 21" long by 13" wide at the pad surface and one totallizer-dial indicator unit. The development of a technique to install the scales effectively for shuttle car-weighing followed an evolutionary process. The setup which finally proved to be effective entailed countersinking and level¬ling the load pads in the floor on the shuttle car trackway such that the tops of the pads were three inches below the floor level. A plat¬form consisting of two braced side-by-side 3" x 8" lumber planks was made. The platform was placed across the load pads with six inches of overlap on each side to provide room for imperfect tracking of the shuttle car. Additionally, 3" x 8" lumber planks were imbedded across the runway immediately behind and ahead of the platform. These auxili¬ary planks were firmly braced into the floor by vertical posts or jacks set against the roof; the planks constituted a stable approach platform to enable the shuttle car to roll unimpeded onto the scale platform in either direction of travel. Figure 22 shows this arrangement in detail. The setup of the scales was done during non-production hours prior to the first working shift of the week. This task took seven to twelve hours with two men. During the actual weighing experiment, the following limitations were realized. 1. Delays will be introduced into the cycle of operations because the shuttle cars must be stopped and positioned on the platform. However, these delays can be held to a minimum, time wise, as the

Jan 1, 1972

By A. B. Cecala

A cooperative research effort was established between the Tilden Mining Company LC, the United Steelworkers of America, and the National Institute for Occupational Safety and Health to lower respirable dust levels in an iron ore grinding and concentrator plant. This cooperative effort involved three field studies to evaluate different techniques to lower respirable dust levels. The greatest impact on lowering respirable dust concentrations throughout this facility was achieved through ventilation changes. The most significant improvement was realized by changing the ventilation profile throughout the entire facility. The ventilation to this grinding and concentrator facility was provided by approximately 40 roof fans operating in either the intake or exhaust mode. The operation of these fans was significantly changed in an attempt to pro-vide more of a directional flow pattern throughout the facility, as well as to more closely balance the intake and exhaust air volume. This change accounted for a 31 pct reduction in respirable dust levels in the primary grinding area of the mill. Another successful modification was to improve the sealing of a reclaim tunnel to the outside and by barricading the access point from the reclaim tunnel to the concentrator plant. This minimized the dust liberated in the conveyor tunnels from traveling through the reclaim tunnel and into the plant. These two modifications illustrate the impact that improvements in ventilation can have on lowering respirable dust concentrations in iron ore processing facilities.

By John C. Edwards, Gerald S. Morrow

The U.S. Bureau of Mines has constructed a smoke chamber and developed sensitivity tests for smoke detectors. Response of ionization- and optical-type commercially available smoke detectors have been investigated. Six smoke detectors were measured with respect to visually obscuring smoke characterized by a corresponding optical density for smoldering and flaming coal combustion in the smoke chamber. It was determined that for one type of ionization smoke detector the alarm time was nearly equivalent to that of an odor monitor's alarm for smoldering coal combustion experiments and earlier for flaming coal combustion experiments. The experiments showed that an average CO concentration of 5 ppm corresponded to an optical density of 0.022 m for smoldering and flaming-1coal combustion. Two of the commercially available ionization-type smoke detectors were more responsive to flaming than smoldering coal combustion at an optical density of 0.022 m, whereas the optical smoke detectors-1showed the opposite trend. The responsive characteristics of the detectors evaluated with respect to known smoke conditions in the smoke chamber shows their potential for use as mine fire sensors or part of a mine atmospheric monitoring system to improve mine safety.

Jan 1, 1995

By J. O. Winget

Amino acids were investigated in conjunction with rare-earth separation by ion exchange to determine whether they can be utilized effectively as retaining agents for metals separation using ethylenediaminetetraacetic acid (EDTA) eluant at 85° to 90° C. Hydroxyethylethylenediaminetriacetic acid (REDTA) and diethylenetriamine pentaacetic acid (DTPA) were the most effective amino acids investigated. Elements of atomic numbers 39 and 57 through 68 were effectively retained, whereas elements of atomic numbers 69 through 71 passed through the retaining-agent band. Utilization of REDTA or DTPA retaining agents allows an increase of 75 percent in the EDTA eluant concentration over that possible with hydrogen-or copper-retaining ions without precipitation occurring. Eighty-five percent recovery of the EDTA eluant collected before rare-earth breakthrough and during elution of lutetium, ytterbium, and thulium, and essentially complete recovery of the REDTA or DTPA retaining agents, are possible without extensive processing.

Jan 1, 1968

Objective: To develop and test a training program that enhances the hazard recognition skills of underground limestone miners. This program can help job performance and lead to enhanced safety in the underground workplace.

May 1, 1998

Miners, like everyone else, must be able to see well in order to work well. But simply hauling bigger and brighter lights into the mines does not necessarily produce better mine illumination. This chapter tells why. Increasing the power of the light source can create problems of portability, glare, adaptation and contrast. This chapter also discusses some ways to increase illumination by Improving the reflectability of walls, roofs and other exposed surfaces. In Chapter IV you learned that the "brightness" of a room or work area was really a matter of how much light was reflected from the walls, roof, and other surfaces. Therefore, if you want to Improve visibility you should increase the amount of reflected illumination. O HOW DOES ONE DO THAT? One way of Increasing reflected illumination would be to increase the power of the light source.

Jan 1, 1976

By L. C. IlsLey

A n'Ulllber or operators have installed f'lBJ!le-proot or so-called exploaion­ proot electrical outfits, under the impression that such equipments met· all of the reqiirements of the Bureau of Mines as regards safety, There a.re todq in gaseous mines a large nwnber of euipments that have not been approved by the Bureau ot Mines, and unless mod1f'iecl could not receive sucl1 approval.. These e qu.ipments represent in pa.rt the product of manufacturers whil ha.ve never submitted. equipments for insri?ction or tests. and iri pat types developed. previous to the safety work or the bureau. Sometiu.es saleimen advocate the use of unapproved. types in gaseous mines in place of Bureau of Mines approved outfits, the purchase price beini slightly less than approved types,

Sep 1, 1922

By G. L. Barlett, J .. D. Barry

Supernatant media of dust-exposed pulmonary alveolar macrophages (PAMs) were inactive in assays for both Interleukin-1 and fibroblast growth factors (FGF). We have begun to evaluate several factors that may interfere with dust-PAM interactions. To determine the effect of sterilization on the activity of dusts, PAMs were exposed to autoclaved dust, heat-sterilized dust or to dust that had not been heated. Supernatants from the first two groups were inactive in the FGF assay, but supernatant from PAMs exposed to unheated dusts stimulated growth of lung fibroblasts. Recent data have revealed that freshly crushed mineral dusts possess labile free radicals that are absent in dust that has been stored for more than a few days. Suspensions .were prepared of a "stale" sample of anthracite dust 867 and of a freshly ground sample of the same dust. These suspensions were instilled intratracheally into guinea pigs under general anesthesia. Two, five or eight days later, PAMs were collected from the lungs by bronchoalveolar lavage, and the cells were counted. At two and five days after instillation, all lavage suspensions contained 70 to 85% PAMs, of which 5 to 18% contained phagocytized dust particles. On day eight there were again 80-84% PAMs in all suspensions, but in the presence of "fresh'" dust, 48% of PAMs. had phagocytized particles in comparison to 16% in the presence of '"stale'" dust. A similar experiment was performed in short-term cell culture. During 24 hours, >95%. of PAMs phagocytized dust particles, whether or not the dust was "stale" or '"fresh". Our studies are being extended to determine the effect of (1) removing surface oil contaminants by organic extraction and (2) suspending dusts without surfactant.

Jan 1, 1988

By John H. Soulé

"INTRODUCTION The Peerless mine was examined by W. R. Storms, an engineer of the Bureau of Mines, on June 2, 1944, in conjunction with a mineral survey of the adjoining For Bayard Military Reservation. Storms again studied the mine on January 13; 15 and 16, 1945, to determine the possibilities of finding new ore reserves to replace these depleted by mining. A project to explore the Peer-less vein at depths below and to the south of the principal mine workings was proposed. Special attention was given to the possibility of exploring favorable beds in the Magdalena and Lake Valley limestones at points near the Peerless fault.The proposed project was approve and exploratory work started on January 2, 1946, and was completed on June 5, 1946. The mine was not in operation during the project, and all equipment had been removed."

Apr 1, 1947

Louisiana's coal reserves, located in the north-western part of the state, consist entirely of lignite, with estimated recoverable reserves of about a billion tons. Although lignite deposits were discovered in the early 1800s, the first documented use of lignite occurred at the federal arsenal near Shreveport during the Civil War. By the late 1800s, lignite use was common by blacksmiths, railroads, and steamboats. Lignite production ceased, however, from the early 1900s until 1985. A new lignite mine permitted September 1, 1985, produced 0.2 million tons in its first year. The operation uses a seven-mile-long conveyor to transport lignite to the associated mine-mouth power plant. The surface coal mining reclamation and enforcement program in Louisiana was approved October 10,1980. Louisiana's Abandoned Mine Reclamation Plan was approved December 10, 1986

Jan 1, 1992

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A computer program has been developed to simulate evacuation of a mine in case of fire in the following, the capabilities, operations and structure of the program are described with illustrative examples to demonstrate usefulness of using the program. A detailed description of the program with sufficient information to make use of the program appears in Appendix B.

Jan 1, 1976

To improve operational effectiveness of enclosed cab filtration systems. Background Enclosed operator cabs are widely used on mobile excavation equipment in the mining and construction industries. They protect the operator from bad weather, noise, and airborne dusts. The inside cab environment usually must be kept at very low dust concentrations because of quartz dust generated from the excavation of silica-bearing rock. Most cab designs achieve heating and air conditioning effectiveness by recirculating most of the interior cabin airflow, with a smaller portion of the outside air added to the cab as makeup air. Both the recirculated cab airflow and exterior makeup air added to the cabin should be efficiently filtered, with the makeup air positively pressurizing the cab interior. Ideally, operator cab air filters should provide at least 99% capture efficiency for dust particles as small as 0.3-pm aerodynamic diameters. These higher efficiency air filters provide good dust control for the equipment operator, but tend to accumulate dust more quickly than lower efficiency air filters.

Jan 1, 2001

1. Mining to prevent and control underground acid formation should begin with education imparted through: (A) Course work at mining schools to teach prospective engineers. (B) Training of engineers presently employed in the mining industry through appropriate mining extension courses. 2. Considerable need exists to devote more attention to: (A) Hydrogeologic studies of mining areas to enhance the planning of new mines and the abatement program of existing mines. (B) Additional research to explore methods of dewatering the strata associated with mining areas. (C) Further effort to develop sealants for preventing contact between water or oxygen and the acid producing material associated with the coal seam.

Jan 1, 1970

By E. F. Ferrell

The Bureau of Mines, U.S. Department of the Interior, studied the use of manganese sea nodules for catalytic oxidation in air of 1 pct carbon monoxide, 1 pct propane, and 1 pct methane. Catalysts were prepared from both Pacific Ocean and Atlantic Ocean nodules and compared with a platinum catalyst using a fixed-bed, steady-state microreactor with gas chromatographic analysis. Combustion temperatures with manganese nodules were 50° to 100° C lower than those with the platinum catalyst. Ion-exchange addition of rare-earth promotors to the nodule catalyst decreased combustion temperatures an additional 5° to 45° C.

Jan 1, 1978

Objective: The Roof Monitoring Safety System (RMSS) provides a first step in roof behavior awareness. By understanding and measuring roof movement in an underground mine, the potential for injuries or fatalities to mine workers from fall of ground can be lessened. Also, officials at an underground mine with a history of data on roof movement are better prepared to make a decision on remedial actions if falls of ground become a problem. The RMSS provides a safer, simple, and inexpensive means for measuring roof movement.

Aug 1, 1998

By Mark Larson, Doug Tesarik, Joe Shoemaker, Brad Seymour

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the backfilled entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backfill provided stability for the roof and floor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right mine through and should provide beneficial case study information for other longwall backfilling applications in the future.

By Sinisa M. Djordjevic, Isaac A. Zlochower, Kevin J. Liekhus, Cindy A. Loehr, Kenneth L. Cashdollar

An experimental program was conducted to evaluate the accuracy of some current methods for predicting the flammability of gas mixtures containing hydrogen and flammable or nonflammable volatile organic compounds (VOCs) in air The specific VOCs tested were toluene, 1,2-dichloroethane, 2-butanone, and carbon tetrachloride. The lower flammability limits (LFLs) of gas mixtures containing equal molar quantities of the components were determined in a 19.4-1 laboratory flammability chamber using a strong spark ignition source and a pressure criterion for flammability. All but one of the LFL values for the individual components were in agreement with earlier literature values. However, the LFL of l,2-dichlorocthane was found to be significantly lower than the range of values reported for previous determinations in smaller chambers. Two methods for calculating the LFL of mixtures were considered. The Group Factor (atomic) Contribution Method was determined to he generally more accurate than the LeChatelier Method for estimating the LFL of the gas mixtures reported here, although the LeChatelier Method was usually more conservative. The Group Factor Method predicted higher values (nonconservative) for the LFLs of several mixtures than were experimentally measured. For the case of a mixture of hydrogen and carbon tetrachloride, the Group Method estimation of the LFL was seriously in error.

By A. J. Miscoe, W. M. McKewan

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mimes' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in- creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 1993

By Launa Mallett, PhD, Charles Vaught, PhD

This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings.