Search Documents

Eliminate the occurrence of false fire detection alarms caused by the operation of diesel-powered vehicles in underground coal mines. Approach Fire detection systems used in underground mines are based on measurements of airborne combustion products such as carbon monoxide or smoke particles. The effectiveness and credibility of these systems can be reduced by the occurrence of false alarms that result from the operation of diesel-powered equipment, which produces the same combustion products. False alarms end up being very costly to the mine operation in terms of downtime and labor needed for verification. To improve upon current fire detection systems used in the presence of internal combustion engine products, the U.S. Bureau of Mines developed a fire detector that can discriminate between the occurrence of real mine fires and the presence of engine smoke.

Jan 1, 1989

By Stuart R. Zimmerley, John Gross

"In the study of ball-mill grinding at the Intermountain Experiment Station of the United States Bureau of Mines at Salt Lake City, Utah, it was desirable to measure the work input to a ball mill at the mill itself so that consideration of motor efficiency and transmission losses would be eliminated.The device adopted is essentially that used by Prof. H. E. T. Haultain4 in measuring work input to rolls. The mechanism was changed only so as to adapt it to a ball mill.Figure 1 is a diagrammatic sketch of the apparatus.The pulley which rotates the mill is loose on the mill shaft and is equipped with ball bearings. This pulley is connected by means of three tangential springs to the driving plate, which is solid on the mill shaft. Power applied to the loose pulley is transmitted to the driving plate, and hence to the mill, by the three springs; the greater the resistance of the mill, the greater the spring extension. The extension of the springs is transmitted by the steel extension tape to the differential integrating meter.The integrating meter is operated by two friction wheels in contact with the integrator disk which revolves at a definite ratio of speed to that of the mill. The friction wheels are held in contact with the disk by the spring suspension of the integrator and are connected to a differential gear cage, the revolutions of which are recorded on a counter such as is used in gas meters. Due to the differential gears the c e is stationary when the two friction wheels revolve at the same speed in opposite directions; this condition exists when the integrator is centered on the disk and corresponds to no load or to a zero spring extension. As the lead is applied, the springs extend and move the integrator from the center or zero point, resulting in a difference of speed between the two friction wheels. Due to the revolution of the differential cage this change in. speed is transmitted to the counter. The integrator and extension tape system is kept taut by means of a light spring attached to the integrator, the spring having just enough tension to assure that the integrator returns to zero when the load becomes zero."

Feb 1, 1931

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

Develop a new method for coal mint pillar stability evaluation and design based on pillar load measurements. Approach A novel approach to chain pillar stability evaluation and design for longwall coal mining panels has been developed by the Bureau of Mines. The evaluation approach uses an INTEGRITY FACTOR as the criterion for stability. Hydraulic borehole pressure cells developed by the Bureau are used to measure stresses in a pillar for stability evaluation. The results are used to improve the pillar design.

Jan 1, 1989

By E. J. Kloos

Bureau of Mines-approved self-contained breathing apparatus of the compressed air demand type were evaluated for performance at low temperature. Apparatus durations, breathing resistances, and airflow rates were measured on machine tests at room temperature and -25° F. Man tests under actual wearing conditions verified the machine test results. Many serious functional changes in apparatus performance occurred at low temperature. Pressure regulators malfunctioned when diaphragms lost flexibility. Under certain conditions frozen condensed moisture sealed exhalation valves and fogged eyepieces. High-pressure leaks, not encountered at ordinary temperature, developed at low temperature. Tests results are discussed generally and specifically for each apparatus. Recommendations are given to obtain optimum performance from demand type breathing apparatus at low temperatures.

Jan 1, 1968

By C. H. Elder, Maurice Deul

Coal degasification boreholes drilled from the surface have been success - fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By James C. Cawley

A summary is presented of existing leaky feeder communications systems currently in operation in North America. Background information pertaining to previous use of leaky feeder technology is discussed along with the survey methodology. A review of some pertinent facts concerning propagation in tunnels and specific reference to mine tunnel propagation is presented. A summary of the characteristics of each mine visited is presented in tabular form, and methods of procurement and maintenance are discussed. The role of user training in efficient system use is presented. Seven sites representing eight mines are included in the survey. Economic and technical topics are considered.

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

This section contains a summary of our investigation of the soil conditions (type, porosity, moisture content, etc.) at the two sites (Lanse and Kato, Pennsylvania) selected for field testing of latex as a soil sealant. Other natural conditions such as rainfall, frostline, depth of the water table, etc., were also measured and recorded for possible later use in assessing the effect of the latex seal on the total environment. The numbered sites referred to throughout this report are shown on the maps of the Lanse and Kato sites (Figures 1 and 2). KA, RB and KC are positions at the Kato site - all other numbered positions refer to the Lanse site. Two other terms used throughout the report which should be explained are “horizon” and "profile". These are synonymous terms for soil layer, A horizon (or A profile) referring to topsoil and B horizon (or B profile) referring to subsoil. The properties that control the flow of water through the soil are of special interest because these will also govern the passage of a sealant into and through the soil. Normally the particle size distribution is a good measure of soil permeability, which is directly proportional to sand content and inversely proportional to silt and/or clay content. Tables I1 and I11 show the percentages of gravel or stones, sand, silt and clay of Lanse and Kato soil samples. According to the United States Department of Agriculture classification, the gravel is ,ignored and the residue separated into sand, silt, and clay fractions. Figures 4 and 5 indicate by means of the USDk soil texture triangle that the variability of composition of Lanse soil ranges from sandy loam in the creekbed to clay loam. The variation is even greater among soil samples from Kato. Porosity of soil, also known as percent voids, is another indication of how readily water will travel through soils. Soil density usually increases and porosity decreases with depth, and as expected, the porosity of the top soil at Kato, a forest, is exceptionally porous and open (see Table IV) The pore diameter and length of soil capillaries is extremely variable, and its distribution in the field is impossible to determine. In addition to the capillaries, soil also contains many macro cracks, crevices, and passages around stones and roots. All these affect the flow rate of water through soil. Poiseuille's law states that the rate of flow of a liquid through a narrow tube is proportional to the 4th power of the radius of the tube. Pore size normally decreases with depth and in soil containing appreciable amounts of silt and clay this is especially true. Thus, deeper soils should be less permeable and such was the case at Lanse and Kato.

Jan 1, 1972

By Daniel Edelstein

Demand for arsenic trioxide increased markedly during 1984 as a result of increased use of arsenical wood preservatives and increased use of arsenicals in agriculture. The increase in agricultural demand was due to a return to production of land with-held from cotton planting under an agriculture program for acreage diversion for some 1983 crops. Supplies of arsenic trioxide were more than adequate to meet increased demand, and prices either declined from, or remained at, the low 1983 levels. In June, ASARCO Incorporated announced plans to close its Tacoma, WA, smelter by mid-1985. Domestic Data Coverage.-Refined arsenic trioxide was produced by two U.S. companies. The major producer voluntarily reported its production to the Bureau of Mines, but to prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1985

Develop an inexpensive, reliable means of quickly detecting and locating trapped miners in underground coal mines, particularly after a mine accident. The Limitations Although the Bureau of Mines has performed extensive research on the use of electromagnetics for locating trapped miners, much of its research trends toward the development of long-range systems designed to locate an underground transmitter from the surface. Such location systems are beneficial; however, there are several limitations regarding their use. Two limitations are weight and cost of the equipment. Most long-range detection systems would be too heavy and cumbersome to be accepted by miners as part of their daily protective equipment. Since such long-range detection systems are usually expensive, it would not be economically feasible for every miner to be provided with a system.

Jan 1, 1984

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a longwall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

Improve the accuracy of commonly-used mine air velocity measurement techniques. Approach The Bureau of Mines, through a contract with Ketron, Inc., conducted a detailed study to establish appropriate, generalized correction factors for commonly-used air velocity measurement techniques. The techniques used were centerline readings, continuous traverse and split traverse vane anemometer readings, and smoke cloud readings (see Bureau of Mines Bulletion 589 for details on the proper use of these techniques). The various measurement techniques were used at different mine test sites to measure different air velocities. The data collected from the test sites were used in a statistical analysis which determined a generalized correction factor for each measurement technique. The correction factor multiplied by the measured velocity was used to provide the true velocity.

Jan 1, 1984

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

By R. V. Ramani, C. B. Manula, A. Owili-Eger

All the input data required to operate the ventilation simulator except the title, are entered with I10 or F1O.O formats. The title is entered with (18A4) format. The floating points are designated by (FP) and the integers by (INT)

Jan 1, 1975

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today's coal preparation industry.

Jan 1, 1977

By E. R. Cole

A lead smelting process that appears to present minimal pollution problems has been developed at the Bureau of Mines, Rolla Metallurgy Research Center. Ten and 100 g samples of PbS mill concentrates were vaporized at 1,000° to 1,100° C in a furnace with an inert gas atmosphere during a 2-hour period. The PbS vapor was transported by the inert carrier gas to the reduction zone of the furnace where it was reduced at the same temperature with excess hydrogen to metallic lead. Lead of 99.9 pct purity was produced. The H2S formed can be decomposed into elemental sulfur and water vapor by a modified Claus process. Approximately 90 pet of the Cu and 70 pct of the Ag and Zn remain in the residue and are potentially recoverable. More than 98 pct of the lead in the concentrates was extracted.

Jan 1, 1974

By B. J. Scheiner

Silver ores from the Candelaria District, Nevada, and Round Mountain District, Colorado, were investigated mineralogically and metallurgically. Silver minerals of four distinct groups were identified: (1) silver sulfide; (2) argentojarosite; (3) silver contained in the iron oxide; and (4) manganese carbonate-oxide minerals, Electrooxidation and acid-chloride leaching techniques were investigated as means of altering silver minerals, and their effects on subsequent silver extraction were determined. Application of the knowledge obtained from mineral leaching studies resulted in development of a sulfur dioxide-sodium chloride leaching sequence for extracting silver from these types of ores. Silver extractions of 80 to 85 percent were obtained by leaching the ores with a sulfurous acid-sodium chloride system. This was an increase of 9 to 61 percent silver extraction over that obtained by conventional cyanidation techniques.

Jan 1, 1973

By A. W. Henderson

Methods for converting WOCl4 to WCle were investigated in small-scale, laboratory apparatus to devise a method for preparing pure WCls suitable for conversion to tungsten metal. Chlorine, COCI2, and CCI4, alone and in combination with various forms of carbon, were tested as chlorinating agents at various temperatures. More than 95 percent conversion of WOCl4 to WCls was achieved with all reagents at 8000 C in the presence of activated carbon. Only CCl4 maintained its effectiveness in the absence of carbon at 800° C. The effectiveness of carbon was found to be related directly to its surface area.

Jan 1, 1968