Search Documents

Enhance hydraulic fragmentation technology by developing alternative grout sealing methods. Traditional grout scaling methods rely on chemical adhesion and require large contact areas to restrict high-pressure fluids. Fluid injection into rock requires economical and effective seals. With economical and effective seals, rock is easily fractured in tension by high-pressure fluid injection (fig. 1). Approach An innovative grouting technique was developed and tested by the Bureau. Slowly hydrating expanding chemicals are placed within a borehole and around a section of high-pressure tubing. Testing was conducted using 9/16-inch-OD smooth-walled injection tubes in 1.5-inch-ID holes. Seal lengths weir less than 10 inches and curing times were less than 24 hours.

Jan 1, 1989

By A. N. Styler

As part of its water-jet assisted rock cutting research, the Bureau of Mines has initiated a study into the mechanism of rock fragmentation by water-jet-assisted mechanical tools. The objective of this research is to increase coal extraction efficiency by seeking an improved understanding of the synergistic relationship between mechanical cutters and water jets, enabling the design of more effective cutterheads. Rock chips collected during laboratory traverse speed jet-assisted cutting tests were analyzed with respect to the size distribution of the chips and the forces measured during cutting. As the water-jet pressure was increased, the size distribution of the product became coarser with V-face type cutting tools producing less fine material than conical cutting tools. Fracture mechanics theory accounted for less than 10 pet of the energy consumed during fragmentation of the rock. The energy consumed by processes other than rock breakage decreased with the use of water jets and increasing advance rate.

Jan 1, 1987

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 B. t. u. compared with 597,000 B. t. u. in 1936. These amounts represent roughly the heat obtainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at refineries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels were 11 percent higher than in 1930; the average operating ratio was 83 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 638,149 billion B. t. u. in 1936 to 663,966 billion B. t. u. in 1937.

Jan 1, 1938

By T. F. Anstett

The Bureau of Mines investigated the availability of platinum from known major deposits in market economy countries. Fifteen of these deposits contain demonstrated resources totaling 302 million troy ounces of platinum. Detailed geologic, engineering, and cost evaluations were performed on each deposit to determine its potential for platinum production. There are large amounts of demonstrated platinum potentially available from market economy deposits that were not analyzed owing to lack of adequate data or to technological limitations. These include 297 million troy ounces contained in the UG2 and Platreef of the Bushveld Complex, South Africa. This analysis indicates that about 11 0 million troy ounces (2.3 million ounces annually) of platinum are potentially available at the January 1980 producer price of $420 per troy ounce, nearly all from South Africa. An additional 85 million troy ounces occurring in Zimbabwean deposits would become available only through more than a quadrupling of that price. In order to meet projected world demand of 3.5 million troy ounces in 1990, platinum price may have to increase. Only one domestic deposit, the Salmon River in Alaska, is capable of producing platinum at $420 per troy ounce. Regardless of price, at assumed production capacities, domestic deposits could supply less than 10 percent of annual U.S. requirements.

Jan 1, 1982

By Richard Hammer

Various alternating current (ac) methods can localize faults in mining power cables. Several methods considered by the Bureau of Mines in this report are the Murray loop for short circuits, wherein a bridge provides proportional distance to the fault; capacitance measurements for open conductors; inductance measurements for shorted conductors; phase comparison, high speed recordings of voltage and current in the faulted state are compared with normal voltage and current with the difference being a function of impedance change and impedance change being a function of fault location; and standing wave measurements, detecting the resonance of the length of cable to a fault (either short or open). Portable capacitance bridges are presently available for the second method, and the fourth method is well developed for use on large power distribution systems. Because it utilizes pulses rather than ac, the time domain reflectometer (TDR) method of fault locating was not included in this investigation. However, a comparative evaluation between this versatile method and the Murray loop might prove advantageous in locating high resistance faults.

Jan 1, 1977

By James R. Means, George Bowser

A new phone system was developed that provides eight full duplex communications channels over a single twisted shielded phone line, with no central switching station or line amplifiers. This system greatly simplifies installation and maintenance over that required with conventional switching systems. The system is based on microprocessor technology and digital frequency synthesis. Frequency division multiplexing is used over a bandwidth of approximately 300 kHz, and a baseband voice channel (compatible with conventional pager phones) is provided as a backup to assure communication if the multiplex features fail. Multiplex operations are controlled over a 30-kHz digital channel. The system is designed to operate with up to 16 km (10 miles) of cable plant and a maximum phone separation of 8 km (5 miles). The digital techniques permit a limited amount of monitoring and control capability to each phone. This consists of two pair of contact inputs or outputs, to be used as desired. These "flags" may be read or controlled by a dispatcher's phone.

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947

To reduce needless paging of persons by all phones in a mine or mill, while retaining all-location page capability. Approach Standard pager phones of any manufacturer are modified to include the option of selective calling and message holding. How It Works All commercial mine pager phones presently rely upon voice paging via a loud-speaker. When a page is initiated, every phone in the system broadcasts the audible voice page, even phones in locations where the desired person could not possibly be. The advantage of this scheme is that whole-mine paging occurs. The disadvantage is that persons soon begin ignoring pages because they occur all the time, and most are for someone else. Also, it requires considerable battery power from all phones making it necessary to change batteries very frequently, even in phone locations where personnel rarely go. In addition, if a voice page is made and not heard, there Is no way to leave the message. Therefore, persons who at a later time come near a phone, have no way of knowing a page was made and was not acknowledged. This results in situations that often have a direct bearing on safety and productivity.

Jan 1, 1980

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968

By Stephen C. Tadolini, Thomas M. Barczak

Western mines have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the early 1990’s provided a very effective alternative and remains the dominant form of tailgate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled together, provides more capacity than an equivalent sized Can support and improves transport efficiency. However, the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but they have not been proven in high deformation environments. Alternative supports are also being used in longwall recovery operations. These include the Rocprop and Omni Prop, which are extendable support systems. They also provide active roof loading which can be beneficial in these applications. Specialty supports, such as the Sand Prop and Spider Prop, have also been introduced into western longwall operations. This paper compares the performance characteristics of these various support systems.

By F. D. Osgood, A. C. Fieldner, W. A. Selvig

In connection with investigations being conducted by the Bureau of Mines regarding pulmonary disease which is prevalent among metal miners in certain districts , a large number of rock- dust samples have been collected , and have been examined in the Bureau's laboratories . The earlier work has been described in Bureau of Mines Technical Paper 105 , " Pulmonary disease among miners in the Joplin district , Missouri , and its relation to rock dust in mines " by A. J. Lanza and Edwin Higgins , 1915 , and in Bureau of Mines Bulletin 132 , " Siliceous dust in relation to pulmonary disease among miners in the Joplin district , Missouri , " by Edwin Higgins , A.J. Lanza , F.B.Laney , and Geo . S. Rice , 1919. The methods of collecting and examining dust samples have been greatly improved during the investigation , much valuable information having been made available by similar investigations conducted by the Miners ! Phthisis Prevention Committee , Union of South Africa . The latter are described in the " General report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1916 " , and " Final report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1919. " The investigations by the Bureau of Mines and the South African committee show that by prolonged inhalation of air containing minute particles of sharp and insoluble rock dust , the lungs retain sufficient dust particles to cause decided injury to the lung tissue , the injured lung becoming very susceptible to the development of tuberculosis .

May 1, 1920

By Philip A. Holland

The Bureau of Mines has developed a method for determining helium in water for use in sampling and analyzing surface and subsurface waters for geochemical survey work. The accuracy of the analytical method is within ±10 percent for samples containing above 20 x 10-8 cm3 He (STP)/cm3 H20. The minimum detectable helium-in-water concentration is calculated to be 2 x 10-8 cm3 He (STP)/cm3 water. Water samples are collected in 500-cm3 stainless steel cylinders. The dissolved gases are extracted into a cylinder of equal volume containing a known quantity of neon. The resulting gas mixture is subsequently analyzed for helium and neon-21 by mass spectrometry. The volume of helium in the sample is calculated from the mass spectrometric determination of the helium-to-neon-21 ratio, the known quantity of neon used, and the extraction efficiency of helium.

Jan 1, 1981

By Richard J. Mainiero, Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small-scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single-hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

By C. H. Elder, Fred N. Kissell, S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

Reduce the cost and incidence of low-back pain in underground coal mines through redesign of materials-handling tasks. Background Approximately 25 pct of all injuries in mining involve trauma to the hack. These injuries account for at least 30-40 pct of worker compensation payments made by the industry, are the leading cause of lost work days in mining, and have been estimated to cost the industry $50 million annually. It is clear that the traditional approach to reduce back injuries (i.e., training) has been largely ineffective. Thus, new approaches are necessary to control this problem. This document briefly describes methods that can be used to redesign hazardous materials-handling tasks to reduce the threat of worker injury. Approach A model for redesigning materials-handling tasks is shown in figure 1. The model outlines the sequence of steps that should be followed (and questions that should be asked) when developing new strategies for handling materials in underground coal mines. A critical examination of the current supply-handling system is the first step to developing safer materials-handling procedures. The purpose is to identify hazardous tasks that can be modified to reduce injury risk. Accident analysis (a review of past accident records) and task analy¬sis (usually a videotaped analysis of hazardous jobs or tasks) arc effective methods of distinguishing areas where job redesign is needed.

Jan 1, 1992

This is the final report on Project CR-102 under the auspices of the Department of Environmental Resources, Commonwealth of Pennsylvania .1 The project was activated on January 5, 1970, with financial support from Bituminous Coal Research, Inc., the Pennsylvania Coal Research Board, and the Water Quality Office of the Environmental Protection Agency (WQO-EPA)2 through Grant 14010 EST to the Commonwealth of Pennsylvania Work on the project was conducted according to the procedures outlined in BCR Research Program Proposal RPP-164R, dated April 24, 1969, and a subsequent Revulsion of Scope, dated February 25, 1970. This report covers the entire project period from January 5, 1970, through March 25, 1971.

Jan 1, 1971

By W. K. Overbey

Knowledge of fracture systems in oil or gas reservoirs is essential to the efficiency of both primary and secondary production operations. A relationship was established between structural features of the surface and both natural and induced fractures in oil and gas reservoirs, thus providing a method of predicting the direction of rock fracture prior to field development and well completion. Correlations between the surface features and under-ground fractures resulted from analysis of joint strike measurements, bottom-hole impression packer surveys, photographs of hydraulically fractured wells, fracture data from oriented cores, in situ strain measurements from formation outcrops, and lineament analyses from aerial photographs. The mean orientation of surface fractures, lineaments, and stress field directions ranged from N 53° E to N 73° E, compared with an average orientation of N 63° E for the hydraulically induced fractures. Tectonic stress field was shown to influence the direction of hydraulically induced fractures. This report presents the details and application of techniques to obtain the orientation of the principal horizontal compressive stress field component and thus the direction of induced fractures.

Jan 1, 1971

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

Develop a machine which can accurately simulate both the breathing and metabolic functions of a human being. The advantages of such a machine over a human being for testing of respiratory protective devices lie in its ability to quantify metabolic input, its repeatability, and the lack of a need to deal with the vagaries of human subjects. Breathing simulation has been widely achieved throughout the world but metabolic simulation has not. Approach Utilize the latest computer technology and place the complex portion of the system in software, leaving the mechanical portion as simple as possible. How It Works The concept for the automated breathing and metabolic simulator (ABMS) was developed through a research contract with the Pennsylvania State University. The ABMS utilizes a continuous removal/replacement concept to simulate metabolic functions, with breathing and metabolic functions being controlled by a computer. The mechanical portion of the machine is simple; the complexity of the system lies in its computer software which is not subject to maintenance problems.

Jan 1, 1987

By M. D. Schlesinger

As part of the development of processes for producing synthetic fuels from coal, the Bureau of Mines prepared a special jet fuel in a pilot plant for evaluation by the Air Force. This jet fuel had all the required physical properties, including the important specifications of high heating value and high density. However, the finished fuel did not pass the stability test specified by the Air Force and conducted by the Southwest Research Institute in a high-temperature research coker. The cause for this instability is being investigated because pure compounds of the type identified in this fuel are known to be stable. The tar acid oil used was a 230° to 300° C. fraction of low-temperature tar obtained by carbonization of a West Virginia bituminous coal in the pilot plant of the Consolidation Coal Co. Both the desulfurization at 400° C. and saturation at 300" C. were done in the vapor phase at 2,500 p.s.i.g. After catalytic treatment and distillation the final jet fuel had a boiling range of 194° to 247° C., a net heating value of 18,420 B.t.u./lb. and a specific gravity of 0.8463 60° F./60° F. It also had u pour point below -62° C., and at 0° C. its viscosity was 4.5 cs. The oil was virtually all bicyclic, 41 pct. noncondensed and 56 pct. condensed.

Jan 1, 1961