Search Documents

Provide low-cost fire protection for big bulldozers. Approach A fire protection system, previously used on mobile logging equipment and adapted to surface coal augers, has now been adapted for use on large mining bulldozers. How It Works Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system. The system can also be manually activated from either the opera-tor's cab or ground level. Location of the principal components of the system are shown in the drawing The heat sensors of the sys-tem consist of bimetallic strip switches which operate at about 10000F temperature. Switch operation results in release of compressed gas from a small storage cylinder. The gas expands to blow the dry chemicals out of the nozzles, in a spray that lasts about 15 seconds. The compressed gas used is usually nitrogen, although carbon dioxide is also used.

Jan 1, 1978

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and2-year time periods during 1990–1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 9, 2004

Minimize the effects of underground mine conveyor belt fires by developing methods to prevent automatic fire suppression system failures. The Problem Fire protection is achieved by prevention, early detection, and planned fire-fighting response. Automatic fire suppression systems are one form of planned fire-fighting response. When these systems are properly designed, installed, and maintained they can effectively control fires. Conveyor belt fires account for about 20% of underground coal mine fires. Fire protection requirements have been established for underground locations because of potential for start and spread of fire and the restricted personnel egress in a fire situation. Belt conveyor systems arc potentially dangerous because of the high fire incidence rate, high temperatures, dense smoke, toxic gases, and rapid flame-spread rate. While investigating the conveyor fire suppression problem, the Bureau identified automatic fire suppression system reliability as a potentially serious deficiency within the mining industry. Table 1 lists common failure modes fur three Fire suppression system types. This table summarizes findings of Mine Safety and Health Administration electrical inspectors responsible for inspection of belt protection automatic fire suppression systems. Batteries, contact points, control wires, and electric servocontrols are all prone to failure. Figure 1 shows rock-dust-contaminated relay contact points. This condition is dangerous because of the chance of intermittent failures, which might allow systems to pass annual functional testing, yet fail during actual fire emergencies.

Jan 1, 1989

To devise an economical, environmentally acceptable method for recycling scrap lead-acid batteries. Approach A combination electrorefining-electrowinning method for recycling lead metal and sludge from scrap batteries was devised which produces a 99.99 + percent pure lead product and eliminates the lead and sulfur oxide emissions that are the normal by-products of high-temperature smelting processes. How the Method Works Lead metal grids and lugs are separated from the battery sludge by washing and screening, and are melted and cast into anodes for electrorefining by the Betts process. The electrolyte used is fluosilicic acid, a large volume waste product generated during the production of phosphate fertilizer. During the electrorefining process, impurities in the anode are trapped and held in an adherent slime blanket on the surface as the anode dissolves while pure metallic lead is deposited on a lead cathode. The major problem in the past has been to recover the lead from the battery sludge which consists of approximately 60 percent lead sulfate, 21 percent lead, and 19 per-cent lead dioxide. In the flow sheet developed by the Bureau

Jan 1, 1983

By M. O. Renwick, Paul Zinner

"INTRODUCTION In September 1943, the Bureau of Mines conducted a limited program of churn drilling on the Winskell property in the Shullsburg area of Lafayette County, Wis. The work was undertaken as part of a general investigation by the Bureau of the zinc-producing area of southwestern Wisconsin at a time when special effort war being made to increase the production of metals necessary for the war program.Drilling described supplemented a previous drilling program conducted by the Vinegar Hill Zinc Co. The results of both programs encouraged subsequent investigation by the Cuba Mining Co. and eventual development of the Andrews mine.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by such project as soon as praticable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the investigative work, and prepares the final report."

Aug 1, 1947

By Parviz F. Rad

The Bureau of Mines conducted rock-cutting experiments under constant normal force and constant penetration in an effort to correlate laboratory data with those obtained in the field. Both independent and interacting groove spacing regions were studied, and optimum and critical cutter spacings were determined. For the laboratory work, the effects of specific energy, muck weight, groove depth, cutting coefficient, and size distribution of the muck for both independent and interacting grooves were studied. For field operations, forward thrust, torque, advance rate, and muck size distribution were the parameters studied. Satisfactory correlation is obtained between laboratory cutting results and field performance data.

Jan 1, 1974

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

Control dust generated during mining in salt mines. Approach A machine-mounted exhaust ventilation system which moves with the cutting machine from place to place was developed. The system captures the dust at the face of the heading and exhausts it downstream of the heading in the crosscut. This helps cause fresh air from the crosscut to flow over the machine operator's position, and aids in keeping the dust cloud close to the face. How It Works The system consists of (1) a circular intake hood with a 10-inch slot extending 250 degrees around the base, bolted to the gearhead; (2) 20-inch-diameter wire-wound flexible ducting to connect the intake hood to the fan (25 ft. is allowed sufficient slack for bar movement); (3) an industrial exhaust fan capable of generating 10,000 cfm with 13 inches water gage pressure at 1435 rpm; and (4) 150 ft. of collapsible 24-inch tubing for the exhaust duct which is de-played and returned In each heading by the cutter operator and/or his helper.

Jan 1, 1983

By Larry P. Jackson

As part of the current research effort in shale-oil chemistry conducted by the Federal Bureau of Mines, reduced chlorophyllins were prepared and pyrolyzed in an effort to identify the role of plant pigments and their decomposition products in the nitrogenous compounds found in the product of oil-shale pyrolysis. The properties of the chlorophyllin pyrolysates were related to the composition of the reduced chlorophyllins with particular emphasis on the amount and types of nitrogen compounds formed. A comparison based on the types of nitrogen compounds present was made betvJeen shale oil and the chlorophyll in pyrolsates. In order to make this comparison, a sample of shale-oil light distillate was separated into polar and nonpolar fractions, and a careful examination of the polar fraction was conducted to obtain an accurate picture of the types of nitrogen compounds present. The information gathered from these studies was used to evaluate reduced chlorophyllin as a model of oil-shale kerogen insofar as the production of nitrogen compounds was concerned. The results indicate that the reduced chlorophyllin does yield nitrogen products which are directly related to the nitrogenous compounds in shale oil, and it therefore represents a good model of shale-oil kerogen.

Jan 1, 1975

Enable prospective in situ leach mine operators to evaluate the economic potential of an ore body by using a user-friendly, computerized in situ copper oxide leach mining cost model. Background As part of its research on in situ leach mining technology, the Bureau of Mines produced a 5-volume contract report that mining companies can use to design an in situ mining operation for copper oxide deposits. Written for the Bureau by the Science Applications International Corporation (SAIC) in 1988, the generic design manual also contains a computerized cost model for evaluating the economic feasibility of in situ leach mining for any specific copper oxide deposit. The cost model is to be used with Volume II of the contract report. But because of certain complexities associated with running it, the Bureau found that the model could be improved by making it more user friendly. Approach The approach taken by Bureau researchers to make the original model more user friendly was to incorporate a HELP function to define input parameters, and to enable the display of output on the monitor. An accompanying handbook, U.S. Bureau of Mines Information Circular (IC) 9284, contains further details on running, the 1990 model.

Jan 1, 1991

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

By Andrew B. Cecala, Edward D. Thimons

"The Bureau of Mines has recorded a number of different background dust sources that significantly contaminated the air breathed by bag machine operators. These background sources, observed at five different plants over the past 2 years, can expose bag machine operators to more significant dust concentrations than the filling process itself. To keep bag operator exposure within acceptable dust levels established by the Mine Safety and Health Administration, U.S. Department of Labor, the significance of these background sources must be realized, and the sources must be identified and controlled. The purpose of this work is to identify common background dust sources and show the significant effects that they have on the bag operator's overall dust exposure. INTRODUCTIONThe purpose of this report is to identify some common background dust sources in and around the bag-filling area. Although these background dust sources are of ten unrecognized, they can be more significant sources of contamination than the dust generated from the bagging process.The bagging of mineral products into 50- and 100-lb paper bags is common throughout the entire mineral processing industry. Bagging is performed by a bag operator who sits in front of a two- or four-station fill machine. The bagger's function is to attach empty bags to the fill nozzles as filled bags are ejected from the machine. If the product being bagged is extremely fine (smaller than 200 mesh), the bag operator's dust exposure is usually one of the highest in the plant.The bag operator is exposed to two primary dust sources. The first is product blowback during the bag-filling cycle. This occurs as excess pressure is released from around the fill nozzle during filling. As the excess air forces its way out of the bag, product is forced out with it. This blowback of product leaving the bag creates a considerable amount of dust. The second major source is the ""rooster tail"" of product thrown from the bag valve and fill nozzle as the bag is ejected from the fill machine. Since the bag is pressurized as it leaves the machine, product spews out of the valve for a few seconds."

Jan 1, 1986

Aid mine workers in detecting hazardous roof conditions in underground mines by developing a method of roof sounding which supplements or replaces the traditional roof sounding technique where the miner relies on experience to determine whether or not the rock is sound. Approach The Bureau of Mines developed an electronic roof sounding de-vice that acoustically determines the integrity of mine roof rock by "listening" to the variation in frequency vibrations within the rock. How It Works n previous research, the Bureau of Mines found that loose rock in a mine, when impacted, vibrates at a much lower frequency and for a lower time period than does a solid slab. By quantifying the enhancement of low frequency vibrations in loose rock over solid rock, a repeatable, objective measure of the rock's soundness can be obtained. This approach was used in developing the rock stability tester.

Jan 1, 1986

By P. W. Jeran

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

SUMMARY The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactc rely demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No. 1 Mine in Grant Town, West Virginia. The remote sealing consists of: (1) A sonar initial probing system which can operate satisfactorily even in the presence of dense smoke. The system is capable of determining both the local passageway geometry, identifying the presence of cribs and other obstructions, and the position of the borehole in the mine passage. (2) A mine sealing material system which utilizes fly ash for making the complete seal or as a bulk filler in conjunction with a urethane, froth foam, seal topping system. The choice of using fly ash alone or fly ash with foam topping depends on a number of factors, such as quality of seal desired, time available per seal, depth of borehole, passageway geometry, and water holding require¬ment. The fly ash-foam seal is a better seal, capable of sealing against a higher water head than fly ash alone. The fly ash sealing

Jan 1, 1973

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974

Reliably measure stress chan¬ges in order to assess stability of mine openings. Approach: A durable, permissible, sensor and readout system have been developed and tested. How It Works: The stress sensing element is a taut steel wire which is, vibrated at its natural frequency, If the tension on the wire is changed because of deformation of the sensor housing, the natural frequency of the wire changes. This effect is similar to decreasing or increasing the pitch of a violin string by loosening or tightening it. Because the stress sensor electrical output is a frequency signal, rather than an amplitude signal, its accuracy is unaffected by the resistance of the signal wire, or other attenuation. Signal wires can be a mile or longer without affecting accuracy. When a button is pushed on the readout box, the sensor wire is electromagnetically excited and vibrates at its natural frequency. That signal causes a readout in illuminated digits. (By referring to calibration chart and the previous reading, the user knows the change in stress.) This system is permissible. To install the sensor, a slightly oversize hole is drilled into the mine pillar. Next, a special tool is used to both position the sensor and wedge it in place. Figure 1, shows the sensor and its integral wedge and hole-fitting piece.

Jan 1, 1976

To cool hot working environments in deep mines more efficiently, while substantially reducing the maintenance required by presently used cooling coil heat exchangers. Approach A mine's chilled water supply cools fresh air enroute to hot working areas, in an improved, direct-mixing heat exchanger. How It Works Warm, fresh ventilation air traveling through the mine's ventilation tubing enters the lower portion of the cooler heat exchanger through a large round opening designed to accept the ventilation duct. This air flow is turned upward and evenly distributed by egg-crate lattice and pair guide vans at the bottom of the cooler. On the diagram, warm air enters at the bottom left. As the air moves upward through the cooler, it passes through a plastic or wire mesh pad which is arranged so that it offers the most resistance to upward airflow immediately above the cooler inlet: this more or less equalizes the upward air flow along the length of the cooler. The air next moves through the cold water sprays, and then through a wire-mesh demister pad before exiting from the cooler at the top right. Cooling of the air is accomplished in several stages. As the incoming air passes through the lower plastic or wire mesh pad, it is exposed to water flowing downward through the pad to the water sump. This is water that has fallen from the sprays or dripped from the upper wire-mesh mist eliminator. This water is slightly warmer than the spray water since it has already done some cooling,

Jan 1, 1981

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981