Search Documents

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

By R. D. Leitch

The pollution of streams by acid mine drainage has become of great importance in the past few years in certain regions of the United States. Large quantities of acids are used in a discharged from other industries than mining, notably in tube, sheet, tin-plate and era hell inn works. These are usually less important then coal mines as a source of acid drainage, because of their more limited distribution throughout the States most affected by acid waters and their relatively smaller numbers. Streams are naturally alkaline and are, therefore, able to take care of rather large quantities of acid wastes, but when such enormous quantities as are often found in mining districts enter the streams, the natural alkalinity is quickly overcome. When a neutral or almost neutral condition has been reached, the further addition of a relatively slight quantity of acids will cause a great difference in the quality of the water.

Jan 1, 1926

By J. G. Croeni

The titanium-iridium alloy system was investigated to determine whether alloys of this system would merit further development as control-rod material for nuclear reactors. A study was made to determine the titanium-iridium phase diagram by using melting-point, thermal analyses, X-ray diffraction, dilatometric, electrical resistivity, and metallographic techniques. The titanium-iridium alloy system was investigated between 500° and 2,400° C. Results indicate the formation of two intermetallic compounds, Ti3Ir rind TiIr3, and one intermediate solid solution centered about the 50 atomic percent iridium composition. A eutectic reaction occurs at 1,475° C, and 19 atomic percent iridium. The Ti3Ir decomposes peritectically at 1,520° C. The intermediate solid solution exhibits a maxima of 2,140° C. at 50 atomic percent iridium. This phase is also believed to undergo an order-disorder transformation at 1,750° C. Another eutectic reaction takes place at 2,000" C. and 60 atomic percent iridium. The compound TiIr3 formed at 75 atomic percent iridium decomposes peritectically at 2,115° C. Further increases in iridium content result in the formation of an iridium-rich terminal solid solution. Information obtained below 900° C. in titanium-rich alloys indicates that iridium acts as a beta stabilizer in titanium, and the authors believe that a eutectoid decomposition of beta-titanium occurs near 500° C. and 10 atomic percent iridium.

Jan 1, 1962

By E. D. Gardner

A custom gold and silver plant is one that treats ores for a fee. Usually such plants are located in mining districts and treat local ores. Ores of milling grade generally can stand only moderate transportation charges. These plants are scattered throughout the West. Most plants now doing a custom business originally were built by mining companies to handle ores from their own mires. As excess mill capacity became available ores from neighboring properties were treated, vainly as an accommodation. Later, as their own ore bodies became depleted, the mills were operated entirely on a custom basis. A few plants pull ore from their own mines only when the supply of custom ore is insufficient to keep the mill operating. Some of the present custom plants were built for custom work alone. Although built originally to treat the ores of the Golden Cycle mine, the Golden Cycle plant at Colorado Springs, Colo., soon became a custom mill and has been operating successfully for many years. It is the largest gold mill in the Western States and. treats Cripple Creek ores, from which most of its tonnage still comes. The plant is equipped to treat a great variety of ores and receives shipments from a wide area. It competes with smelters in Colorado, as it has a roasting plant to prepare sulphide concentrates for treatment in its cyanide plant. Most custom mills, however, are not adapted for more than one or two kinds of ore. Gold occurs in its ores both in the metallic state (free) and locked up in sulphides. It also occurs in a few places, notably at Cripple Creek and a few other Colorado districts, as tellurides. Mien the gold occurs in the native state, the ores is said to be free-milling and can be recovered by amalgamation. Usually, however, some subsidiary treatment is required to make a satisfactory extraction. Amalgamation generally was followed by tabling in the earlier mills; at present, flotation has replaced tables at many places. As depth is reached in raining and the workings extend below the oxidized zone the character of the ore usually changes, or, as the miners say, "it gets base". Since the advent of flotation, the average recovery of gold in base ores has been improved-greatly. Cyanidation is applied to some types of both gold and silver ores. The recovery by cyanidation is in general considerably higher than by other methods in vogue and in addition has the advantage of making a finished product which can be sold directly to the mist, thus obviating smelting charges on concentrate and discounts

Jan 1, 1935

By G. T. Brow

An experimental method is described for testing diffusion of gases in crude oils at pressures and temperatures up to 3,000 psia and 200° F. A sampling technique was developed to withdraw by constant-pressure mercury displacement about 60 µl of oil from the diffusion cell through any of several 1/2-in vertically spaced capillary tubes and to trap about 4 µl of the oil in a specially designed microsampler. Oil trapped in the microsampler can be completely inserted in the sample inlet of a chromatograph. From analysis in a three-stage chromatograph (GLC), gas concentration in a sample is determined from the ratio of gas peak heights to area of peaks of reference components (hexanes or heptanes) in the oil. A diffusion coefficient is calculated from measured concentration profiles with known equations for diffusion in finite or semi-infinite systems, depending on whether the gas has or has not reached the end of the oil column. Results are given for a test of methane diffusing at 2,560 psia and 160° F in crude oil from the Weber Sandstone reservoir in the Rangely field, Colorado. A constant diffusion coefficient of 3.34 X 10-5 cm2 per sec was obtained which gives a good fit between calculated and experimental profiles determined at six times after start of diffusion. The maximum standard error of gas concentration determinations experienced with this method was ±0.88 ml per ml of gas-free oil.

Jan 1, 1970

Decrease the dust concentrations at the shearer and reduce downtime associated with spray system maintenance. Approach Increase the quantity and quality of the water supply on longwall faces by decreasing pressure losses, Increasing pump capacity, and installing a "non-clogging" filtration system. How It Works Water sprays and ventilation are two of the primary methods of dust control on longwall operations. Increasing the quantity and quality of the water supply to spray systems is one of the more effective and least costly dust control methods that operators have at their disposal, yet this method is largely ignored. Poorly positioned spray nozzles operating at low pressures (and flows) which plug frequently cannot be effective. Water supply system Improvements should be a fundamental part of all longwall dust control plans. Upgrading a water supply system may require one or more of the following improvements depending upon where a particular system may be deficient: Increasing pump capacity for additional flow and pressure; increasing line sizes to decrease pressure losses: and, decreasing maintenance downtime and Improving water quality by installing a "non-clogging" filtration system.

Jan 1, 1981

By C. W. Smith

Research was conducted by the Bureau of Mines to determine the effectiveness of various types of crushers for use with the Bureau-developed pneumatic concentration technique for mica. Three types of crushers were investigated in this study, a roll crusher, a jaw crusher, and a hammer mill. All the mica concentrates produced contained over 82 percent mica, but recoveries varied considerably. The roll crusher gave the lowest recovery of 46 percent of the mica followed by the jaw crusher with a recovery of 50 percent of the mica. The hammer mill proved the most effective, producing four concentrates with recoveries of at least 70 percent.

Jan 1, 1981

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982

By E. G. King

The work described in this Bureau of Mines report was undertaken to fill a need of industry for high-temperature heat-content data for uranium tetrafluoride. Without such data, heat balance evaluations of processes involving this substance are seriously hampered. Measurements of the heat content of uranium tetrafluoride were conducted at temperatures from 298° to 1,350° K. The melting point and heat of fusion were determined. The results are presented in suitable tabular form, and representative heat-content equations are included.

Jan 1, 1961

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By E. J. Ostrowski

The Bureau of Mines experimental blast furnace, Bruceton, Pa., was operated to determine the feasibility of replacing part of the burden coke requirements with solid fuels injected directly into the smelting zone. This report describes preliminary experiments and information resulting from such an interchange. These experiments were made on an all-sinter burden, using two parts sinter to one part fuel. Anthracite fines were injected intermittently into the smelting zone of the furnace by compressed air through auxiliary tuyeres. The interval between injection periods ranged from 5 to 15 minutes. A maximum of 28 percent of the stock column coke bur-den was replaced. This percentage replacement caused furnace malfunction, but the overall percentage of these experiments indicated that 20 to 24 percent of the coke requirements could be replaced in this way. The metallurgical coke consumption was decreased by as much as 377 pounds (25.3 percent) per ton of pig metal produced. Buckwheat anthracite No.4 was used in this experiment; however, such solids as bituminous coal or coke fines also could be used. The frequency as well as the quantity of solid fuel injected has a direct bearing on furnace performance.

Jan 1, 1960

By Stephen Gerard Sawyer

The Bureau of Mines developed a method for analyzing elastically certain types of protective cabs and canopies used on underground electric face equipment. The method is based on plane frame theory, and to be amenable to analysis by this method, cabs and canopies must contain symmetry about one plane. Additionally, protective structures with one or more top members in the long direction that do not frame into the columns should be approximately twice as long as they are wide and have two or more internal top members in the short direction. The assumptions and limitations of the plane frame method as regards analysis of three-dimensional cabs and canopies are discussed. A step-by-step procedure for application of the plane frame method is given, and three example canopies are analyzed following this procedure. Elastic strengths calculated for the three example canopies compare within 10 percent of those computed by the more complicated space frame analysis. Formulas employed in plane frame analysis of cabs and canopies are given in the appendixes.

Jan 1, 1973

Develop a method for mapping planar geologic features in deep underground mines where the presence of metal interferes with compass readings. Background A fundamental problem of mapping planar geologic features in deep underground mines is the presence of metal (water and air pipes, track, equipment, etc.), which affects the accuracy and consistency of compasses. Present geologic mapping methods include use of transits or theodolites, both of which are cumbersome and time consuming to use. To complicate the mapping, process each planar feature must be surveyed, and if that feature is not apparent on the opposite wall, it cannot be mapped. Another method of mapping is to stretch a tape measure between two survey spads and place a string along a planar feature on one wall and out into the opening until it intersects the tape measure. This method, in addition to being time consuming, is also inaccurate. Because detailed mapping of planar geologic features deep underground involves many repetitive measurements, a quick, accurate, and reliable method for making such measurements was necessary. The geolaser was developed to make such measurements in deep underground mines where metal interferes with conventionally used compasses.

Jan 1, 1990

Validate the premise that there is measurable seismic activity associated with abandoned mint lands and that this activity can be used to determine stability of the abandoned mine openings, failure cycle of these openings, and susceptibility of the area to surface subsidence. Approach The U.S. Bureau of Mines conducted field investigations at two geologically contrasting sites, Colorado Springs, CO, and the Allegheny Portage Railroad Historical Site near Cresson, PA, to demonstrate that developing monitoring technology can be applied to any site. An array of seven geophones (velocity-measuring sensors) were strategically located to encompass an area at each site where failure in the underground mine openings could be expected, based on historical, geological, and engineering information. How It Works Bureau research has effectively demonstrated that stress changes within a rock mass can stimulate the development of cracks and fractures, resulting in the release of strain energy that generates seismic waves. These seismic waves, traveling outward from their source, can be detected, and the point of origin can be located in three-dimensional space. Furthermore, these seismic signals contain information that defines the source mechanism and the conditions between the source and the receiving sensor.

Jan 1, 1992

By R. K. Koch

In seeking substitutes for such critical metals as chromium, cobalt, and nickel, the Bureau of Mines investigated techniques for shape-casting titanium in rammed sand molds. Castings were made in olivine, garnet, chromite, and, for comparison, zircon. It was found that commercial-grade castings up to 31 lb (maximum capacity of furnace) could be made in zircon or olivine molds if a zirconia mold wash was used. Castings up to 4 lb could be made in chromite molds, but heavier castings suffered from some mold-metal reaction. Garnet molds were found to be unsatisfactory for castings of all sizes because of gas blows and rough surfaces. In other tests shell castings of acceptable quality were produced in water-glass-bonded zircon and olivine molds up to weights of 8 lb, but chromite molds were unsatisfactory because rough casting surfaces were caused by mold-metal reaction. Unlike the currently used commercial processes, neither the rammed-sand nor the shell-molding processes developed by the Bureau of Mines generate noxious fumes at any step.

Jan 1, 1980

Research workers from the Bureau of Mines and industry met with other government and industry representatives at the Mont Chateau Lodge, Morgantown, W. Va., on May 30-31, 1973, to discuss the current status of methane control in eastern U.S. coal mines. The opening remarks, the eight technical presentations, and the discussions of the members of a government-industry panel are published here for the benefit of those concerned with the control of methane in coal mines. In addition, an introduction has been added to present the background of work in this field.

Jan 1, 1973

Minimize airborne respirable quartz dust produced by continous mining machines. Approach Install a shovel-mounted underboom water spray system on the off-curtain side of the mining machine. Dusty air containing quartz is momentarily trapped under the boom, where it is captured by fine spray mist. The remaining dust cloud is directed immediately behind the curtain before it can migrate back to the machine operator's location. How It Works Previous studies have shown that most of the dust generated by continous mining machines occurs under the boon as the cutter head shears down. The primary source of respirable quartz dust on many continous mining operations is cutting or trimming roof rock immediately prior to shearing. This results in very high concentration , of

Jan 1, 1989

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed ?mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

Continuous remote sensing of air speed In underground mine airways. Approach An ultrasonic technique measures a form of air turbulence which is proportional to air velocity. How It Works The stainless-steel enclosed transducer consists of a sensing head with circuitry, and a telemetry card. The sensor uses a patented ultrasonic technique to measure a form of turbulence created In the air. This turbulence, known as vortex shedding, is related to the air speed through the sensor. Air flowing past a cylindrical post creates vortices which flow down the air stream on both sides of the post. Pulses from an ultrasonic transmitter pass through the vortices to a receiver; the effect of the vortices on the pulses is a measure of air velocity. The transducer contains a telemetry card, known as an accessor, which transmits reports on air velocity through a pair of wires to a monitoring system. The accessor contains an analog-to-digital converter and digital telemetry circuitry required for computer system operation. The transducer does not contain any read-outs or alarms and air velocities are displayed by means of a centrally located

Jan 1, 1982