Search Documents

By B. Olson, V. A. Marple, D. J. Radet

"Gravitational forces have been found to be an important factor in defining the particle collection efficiency curve of inertial impactors for large particles. In general it was found that if the parameter G = gW /V 0 2 (g is the gravitational acceleration. w is the nozzle diameter and V 0 is the average fluid velocity at the nozzle throat) in greater than 10-3 the efficiency curve would shift to lower panicle sizes. No effect could be seen for lower values of G.IN'IRODUCTIONInertial impactors have long been used as classifiers for airborne particles. By proper design of the nozzles and flow rate it is possible to classify particles with a fairly sharp cut in the particle size range from approximately .02 µm to 50 µm. Because of inertial impactors wide usage they have been extensively studied calibrated and evaluated. Most of these studies have been experimental calibrations of single stages using monodisperse aerosol particles. However, due to impactor simplicity. i.e. a jet of particle laden air impinging upon a flat plate with large inertia particles crossing the streamlines and impacting upon the plate the impactor also lends itself to theoretical evaluation.The most comprehensive method for analyzing impactors theoretically is to use finite difference solutions to the Navier-Stokcs equations and solve for the velocity components and pressure at node points of a grid placed over the area of interest. Using iteration and relaxation techniques the value of the velocity vectors can be determined at these node points with good accuracy. Once the velocities arc known, theoretical particles of known size can be placed into the now field and their trajectories determined by analyzing their equation of motion using numerical methods.Rader and Marple (1985) have performed theoretical analysis on impactors and have included such factors as Ultra-Stoksian .drag and the physical diameter of the particle in their analysis. However, even with these· factors included, there appears to be discrepancy · between the experimental and theoretical results when the particle size is larger than approximately 4 or 5 µm. One possible reason for this discrepancy could be the effect of gravity on the particle as it passes through the impactor. Therefore, a program was initiated to study the effects of gravitational forces on the collection· efficiency of particles in impactors. The results of that study arc presented here."

Jan 1, 1990

By James E. Bell

Quartz crystals occur on a farm in the vicinity of Laurel Fork, Carroll County, Va., in abundance over a large area, This has been known for several years, but no work had been clone, up to the Bureau of Mines examination in 1943, to determine the amount of crystalline quartz of usable quality. Field exploration was undertaken throughout the month of June 1943.

Jan 1, 1950

By John Gross

The Alaska Station of the Bureau of Mines has recently conducted tests on two tailings from black sand which had been treated previously at the Station. The results of this previous treatment have be on given in a paper entitled "Recovery of Gold from Black Sand by Classifier Concentration." The gold in these tailings was intimately united with quartz, and was so finely divided that it could not be detected with the naked eye, nor even by P&nn ing unless the material was ground. Its fineness is further shown by the assºy result, which reported only lz per cent of the gold content as "metallics", Wºorea's the assay of the original sand reported 36 per cent of the gold as "metallics." The fact that the gold was in such fine particles, closely united with quartz, precluded further recovery by amalgamation without grinding. On the other hand, the small content present, as well as the lack of grinding appliances at the placer mines of Alasia, made it necessary that the material be cheaply handled if at all. With these facts in mind the experiments described below were undertake.n.

Oct 1, 1920

It is now widely accepted that horizontal stress is present nearly everywhere underground. Often it is more severe than the vertical stress. It is a major cause of roof control problems in underground mines. The AHSEM computer program contains two modules to improve mine layouts for control of horizontal stress. For development, the user specifies the orientations of the maximum horizontal stress, the entries, and the crosscuts. Angled crosscuts may be used, and the angles may be different for the right- and left-hand crosscuts. AHSEM then shows the user how the stress condition would vary as the entry and crosscut orientations are changed. The second module is for longwall mining. Severe stress concentrations can make headgate conditions hazardous when the entries are improperly oriented. AHSEM shows whether a particular longwall orientation and extraction sequence places the headgate corner in a stress concentration or in stress relief. It also estimates the magnitude of the stress concentration.

Apr 1, 2003

By Zsuzsanna Zborovszky

Experimental study directed toward gaining improved understanding of the exact mechanisms causing ignition in the PTB breakflash. Investigation and comparison of tungsten and copper wires as to their ability to cause hot wire ignition. Evaluation of the importance of discharge duration in the ignition process. Study of the parameters influencing the duration of a discharge (minimum discharge voltage, purity of electrode materials, purity and properties of the gaseous atmosphere contaminations, deposits on the electrode surface).

Jan 1, 1976

Montana's coal reserves are estimated to be more than 120 billion tons, 24.6 percent of U.S. reserves. Montana's reserves are the largest in the nation. Coal fields are located throughout the state, primarily east of the Continental Divide. Three of the state's 17 coal fields have producing mines. Coal resources range from lignite to high volatile bituminous; however, most of the coal currently mined is subbituminous. Although Lewis and Clark mentioned the presence of coal along the banks of the Missouri River in Montana in 1805, the first major mine was not opened until 1867, at Chestnut, Montana, near Bozeman. The mine at Chestnut served Fort Ellis until the mine was bought by the Northern Pacific Railroad in 1883. By 1900, underground coal mining had developed throughout the state, primarily to supply fuel to the railroads. In the 1920s, large-scale surface mining began in Colstrip to fuel railroad steam engines. Currently, all coal mined in the state is produced from surface mines. The Office of Surface Mining granted the Montana regulatory program conditional approval April 1, 1980, followed by final approval February 1 1,1982. Montana's Abandoned Mine Lands Program was approved November24,1980, and its emergency program was approved August 18, 1983. A Federal Lands Cooperative Agreement was approved May 8, 1981.

Jan 1, 1992

By Ronald A. Vary

This paper is one of a series prepared by the United States Bureau of Mines dealing with milling methods and costs. In view of the current revival of interest in gold mining, information dealing with practices and costs in the development of gold properties is apropos. Milling practice at a small gold property in the prospect stage is described where, with a small outlay for plant and equipment, development has been carried on for about 20 months on the proceeds of the mill operation with little additional expenditure. The paper shows about what may be expected as to costs at a small property operated under northern climatic conditions and with rigid economy throughout the plant.

Jan 1, 1931

By Henry Kreisinger, John Blizard

This preliminary statement presents some of the results of tests carried out at the Lakeside Station of the Milwaukee Electric Railway and Light Co. , by the fuel section of the U. S. Bureau of Mines , in cooperation with the research department of the Combustion Engineering Corporation of New York . The object of these tests was to determine the thermal efficiency , ease of operation , and other particulars of a boiler equipped with specially designed furnace and burners for burning powdered coal . The boiler tested haş 13380 square feet of heating surface , and is one of eight boilers equipped with the Lopulco powdered coal system supplying steam to two 20,000 -Kw . steam turbines in the largest power house burning powdered coal . Twenty- six tests were run at rates of heat transference varying from 4000 to 8000 B.t.u. per square foot of boiler heating surface , and the mean thermal efficiency attained was about 84 per cent , based on the gross calorific value of the fuel as fired . The efficiency varied little with the rate of steaming , and its high value is accounted for by the small loss from incomplete combustion and the small amount of excess air which varied from 5 to 36 per cent . The coal burned had a gross calorific value of about 11500 to 12800 B.t.u. per pound , contained 2 to 5 per cent moisture , 33 to 36 per cent volatile matter and 9 to 13 per cent ash, and was so ground thaf 89 to 95 per cent would pass through a 100- mesh sieve . The ash had a softening point of 2150 to 2450 degrees F. , but did not fuse together at the bottom of the furnace because it was partly protected from the flame radiation by means of a series of water tubes connected to the boiler which were placed between the fumace bottom and the flame, ..

Jan 1, 1923

By Lung Cheng

The Bureau of Mines has installed passive water explosion barriers in two operating mines to determine their usefulness in U.S. coal mines. The primary objective of this field trial was to determine the effect of the explosion barriers on mining operations. Data were also obtained on the ability of the barriers to withstand the mine environment and on the effect of the barriers on belt operation, ventilation, worker travel, and rock dusting. Fifty barriers were installed at three separate beltway locations, and periodic inspections were made. A year after installation, no defects of the barriers or support hardware were detected, nor was any complaint as to the presence of the barriers made by the mine personnel. To date, 2-1/2 years after installation, the barriers have had no detrimental ef-fect on rock dusting, belt operation, or ventilation. Costs of material, fabrication, and installation are reported herein.

Jan 1, 1984

By Charlie Wyche

Principal mineral products in the Dominion of Fiji were gold, silver, pit and quarry construction materials, and cement. In 1981, the combined value of these commodities accounted for about $11.6 million,2 over 85% of the total value of mineral output. Production of cement, sand and gravel, and quarry products increased substantially above the 1980 level. Mining bated on gold production was decreasing, and employment in the industry was declining. The better grade deposits in the one active mine were worked out, and only another 10 years' production at current rates was estimated to remain. While the high world gold price of 1979-80 led to intensive exploration, there has been little sum.

Jan 1, 1983

By Robert C. Hickman

"INTRODUCTION Two holes were drilled on the G. S. Stiner zinc prospect, in the Lead Mine Bend area of Union County, Tenn. The holes were drilled in the vicinity of an area of gossan float and were bottomed in the Maynardville formation of the Nolichucky shale. Drilling was started January 24 and completed February 16, 1947. The total footage drilled was 421.2 feet.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative Work, and prepares the final report. The Metallurgical Branch, Cliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the general supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Raleigh, N. C.LOCATION AND ACCESSIBILITYThe prospect is located approximately 20.5 miles southwest of Tazewell, Tenn. It is reached from Tazewell by driving 13.8 miles southwest on State route 33, thence 6.8 miles over graveled roads in a northwesterly direction to Stiner's general store. The drill holes are located in the bottom land northeast of the store (fig. 1 and 2)."

Feb 1, 1948

By Richard F. Hewlett

Use of digital computers makes possible a more efficient and complete analysis of data from a mineral deposit . This computer program was written and used during an investigation into the efficiency of methods of computing grade and tonnage of ore , wherein it was necessary to make repeated computations involving different combinations of data . This investigation was part of a continuing program of sampling methods research at the Bureau's Denver Mining Research Center.2-4 This program is designed to compute tonnage and average grade for 40 cutoff grades using either the statistical or polygonal methods . tational rate is from 200 ( input bound ) to 1,400 assays per minute , depending on the use of either individual ( one assay per card ) assay- interval length or

Jan 1, 1963

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By John M. Gomes

Two methods for electrowinning tungsten from wolframite [(Fe,Mn)W04] were investigated. The first method, direct electrowinning from wolframite concentrate dissolved in molten salt mixtures composed essentially of various combinations of sodium phosphates, sodium borates, and sodium halides, yielded impure products. The second method was electrowinning from a halide-tungstate melt that was obtained from a high-temperature, two-phase extraction of tungstic oxide (W03) from wolframite. Electrolysis in electrolytes prepared from addition of sodium metaphosphate (NaPO3) and boric oxide (B2O3) to the halide-tungstate melt produced tungsten metal of 99.9 percent purity. Tungsten carbide (WC) was electrodeposited from the halide-tungstate melt when the melt was adjusted to contain 82 mole-percent NaCI and 6.0 mole-percent each of W03, sodium metaborate (Na2B204), and caustic soda (NaOH).

Jan 1, 1970

By W. W. Simpson

The Bureau of Mines conducted research to determine the effects of potassium trithiocarbonate (KTTC), a degradation product of potassium ethylxanthate (KEX), on flotation of chalcopyrite and molybdenite. Small amounts of KTTC were identified in fresh and aged solutions of KEX using thin-layer chromotography. Hallimond tube flotation tests on pure minerals showed that KTTC acts as a weak collector for chalcopyrite. Both KEX and KTTC tend to depress molybdenite, but the depression effect is easily overcome by addition of a small quantity of fuel oil. The results of the Hallimond tube tests were confirmed in batch flotation tests using a porphyry copper ore.

Jan 1, 1983

By F. E. Griffith, C. H. SEELING

Cardox blasting is used widely in coal mines in the United States . A model of a Cardox blasting device was approved by the Bureau of Mines subject to certain conditions and limitations , and the approval was extended to other models from time to time . Certain special hazards are entailed in the use of Cardox as with explosives . One of these is flying shells . In some blasts , the Cardox shell is violently ejected from the borehole and flies like a projectile , frequently ricocheting off solid objects and striking points considerably off the line of its initial flight . Flying shells have been known to pierce the webs of structural - steel beams , to pass through both sides of allsteel mine cars , to be driven through stout hardwood timbers , to knock out timber sets , to damage loading equipment , and to break or short - circuit power lines . A considerable number of shot - firers and other workers have been struck by flying shells and killed or injured . Accidents from this cause , although not as frequent as other types of mine accidents , are usually serious , closely approximating accidents caused by blasting with ordinary explosives . The increasing number of such accidents prompted a Bureau of Mines field investigation of possible methods of preventing dangerously violent ejections of Cardox devices . This report contains pertinent data collected during the investigation and describes methods tested and discarded as well as the development and proof of an apparently satisfactory method .

Jun 1, 1943

Develop a more efficient method of testing the integrity of in-situ leach mining operations. The Problems For economic and environ-mental reasons, in-situ leaching operations must be sure that wells do not leak. Loss of solution in large quantities can be expensive in itself, and if such losses result in pollution the costs can be even higher. Wells are usually tested for leaks by sealing them with packers, pressurizing them and monitoring the pressure drop. However, many commercially-available packers are designed to be used in steel-cased wells rather than the fiberglass-or plastic-cased wells used for in-situ mining. These packers are heavy, cumbersome, expensive, and often leak. In addition, commonly used well-integrity-test systems require lengthy test periods and drill rigs or hoist trucks with rigid pipes must be used to run the packers in and out of the well. The Bureau of Mines has developed a mobile, self-contained leak-testing system that is faster, uses trailer-mounted equipment that can be operated by one person, and features a new inflatable packer.

Jan 1, 1985

By H. H. Fukubayashi

This Bureau of Mines report describes the development of a pyrometallurgical process for the recovery of the zinc and lead contained in brass smelter flue dusts, which constitute a recycling or disposal problem. Tests on brass flue dust from several sources were made in a quartz tube, heated by an electric furnace to temperatures as high as 1,050° C. The dusts were mixed with carbon and heated in an oxygen-free atmosphere. It was demonstrated that 98 pct of the zinc and 12 to 25 pct of the lead, both in the metallic state, could readily be removed from the dusts. It was also found that 75 pct of the zinc could be recovered, with less than 0.1 pct of the lead, in the absence of chlorides. Pelletization techniques were investigated and 0.6 inch pellets were found to be optimal. Pelletizing results in a tenfold reduction in volume.

Jan 1, 1974

By T. G. Carnahan

The Bureau of Mines conducted laboratory-scale weathering research on a leach residue containing elemental sulfur and mixed metal sulfides. Experiments were performed to determine pH and impurity element concentrations in the effluents as functions of time and to determine the effects on effluent concentrations of mixing the residue with dolomite tailing material. Four 800-day tests were conducted simultaneously. Soluble metal concentrations, especially zinc and copper, were excessive in the effluents from washed and unwashed samples of the residue. Concentrations of up to 20 g/l of Zn and 12 g/l of Cu were obtained. The pH values of the unwashed and washed residue effluents at the completion of the experiments were 2.8 and 1.9, respectively. Sulfuric acid from oxidation of pyrite caused the pH decrease. Mixing unwashed residue with dolomite tailing to maintain a near-neutral pH minimized the heavy metals content in the effluents. The pH in the dolomite tests increased slowly after the first 360 days and attained values of 7.8 and 8.2, respectively, for tailing containing 1 pct leach residue and for tailing devoid of leach residue. Dissolved zinc and copper did not exceed 0.10 g/l of Zn and 0.001 g/l of Cu.

Jan 1, 1982

By A. L. Engel

Simple treatment methods, employing the least possible equipment, can sometimes be established for marginal ores and economical results achieved. In continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno Station of the Bureau of Mines, typical ores from newly discovered or recently explored mining districts have been investigated. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores, as well as the conservation and recovery of values in products from former operations that were discarded because of past inability to treat them economically. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas some involved samples of old dumps or tailings piles. The test, work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials; and because, inasmuch as the samples were representative of the districts from which they were obtained, this in-formation should be helpful in the future development of these districts. The present report is a compilation of results of brief preliminary tests on oxide ores only, which contained gold and silver and in some cases base metals. The methods of treatment used include gravity concentration, amalgamation, flotation, and cyanidation. For the most part, only standard laboratory procedures were employed. No attempts were made to develop new methods for the low-grade refractory ores in this group of samples if simple treatment was not successful, as the stage of development of the properties did not warrant extensive experimentation on the samples submitted.

Jan 1, 1951