Search Documents

By John E. Kelley

Laboratory equipment, which simulates abrasive impacts between steel and minerals that might be present during pneumatic transport of coal, was used by the Bureau of Mines to characterize the potential explosion hazard of such collisions in an atmosphere of fine coal dust, air, and methane. A variety of coal mine rock materials, including sandstone, limestone, and pyrite-bearing limestone, were impacted with specimens of pipeline steel. Tests were con-ducted in atmospheres containing zero to 6.4 vol-pct methane mixed with zero to 300 mg/l coal dust. Coal dust in air alone was not ignited by abrasive impacts, but additions of as little as 1 vol-pct methane to the coal dust and air mixture resulted in ignitions. Steel impacting against sandstone caused ignitions in mixtures of coal dust, air, and methane, and the probability for ignitions increased with an increase in methane. No ignitions occurred with impacts of steel on lime-stone or pyrite-bearing limestone, even when large showers of sparks were produced. Studies of the effect of tangential collision velocity showed that no ignitions of coal dust, air, and methane occurred below 900 fpm (4.57 m/sec). Ignitions in coal-air-methane mixtures were found to be caused by a hot friction-induced smear on the impacted rock at the impact site rather than by sparks. High-speed photography was used to verify this observation.

Jan 1, 1976

By John Ward Smith

An analytical method developed by the Bureau of Mines to determine dawsonite, nahcolite, and nondawsonite alumina (called excess alumina) extractable from Green River Formation oil shales is presented. The method requires water extraction of nahcolite followed by HCI-extraction of dawsonite and an unidentified mineral yielding excess alumina from the water-leached residue. Instrumental determination of sodium in the water extract and sodium and aluminum in the HCI extract measures the sample's content of the minerals. Detailed evaluation shows the method to be adequately specific, precise, and reproducible and free from uncorrectable interferences. The method's results define precisely the production of sodium carbonates and alumina possible from a sample of oil shale and the interval it represents. Shale-oil yields, nahcolite contents, and yields of extractable alumina determined on 83 samples representing an 821-foot section of dawsonite-nahcolite-bearing shale from .Colorado Corehole No.3, drilled in the north part of Colorado's Piceance Creek Basin, are presented. These samples resulted in nahcolite contents to 53.3 percent, oil yields to 48.3 gallons per ton, and alumina yields to 5.80 percent. Use of these data to evaluate the production potential of a section of the formation are suggested.

Jan 1, 1969

By V. A. Marple, K. L. Rubow

"4.1 IntroductionIn previous chapters impactors have been described as useful instruments for classifying particles by their aerodynamic diameters and for measuring particle size distributions. These impactors can be used most reliably if the user has some understanding as to how the impactor classifies particles and what parameters are important in this classification process. This understanding can best be obtained by a theoretical inspection of inertial principles.This chapter reviews the most recent theoretical impactor work and the latest theoretical efficiency curves. Procedures are then given for using these efficiency curves in the design and evaluation of cascade impactors. Finally, several examples are given comparing theoretical and experimental efficiency curves, pointing out when the theory can be used with great confidence and when the theory should be used only as a guideline.Due to the rather simple principle of operation of an inertial impactor (i.e., the impingement of a jet of particle-laden air on a flat plate) the impactor readily lends itself to theoretical analysis. Three notable works in the early 1950,s were those of Davies and Aylward (1951), Davies et al. (1951), and Ranz and Wong (1952).Davies and Aylward (1951) used a method of conformal mapping to obtain an analytical solution to Euler's equation for the flow of a frictionless fluid through a rectangular impactor. Numerical calculations were then carried out whereby the equations of motion of the particles were solved in a stepwise manner, leading to a determination of the efficiency curves. Since this theory assumed potential flow, the effect of Reynolds numbers on the characteristics of the impactor could not be determined.Ranz and Wong (1952) used an approximate flow field to calculate the efficiency of both round and rectangular nozzle impactors. In the vicinity of the stagnation point, the flow field was assumed to be that of frictionless stagnation flow. Here, the resulting equation of motion for the particles was found to be in a form similar to equations for free vibration with viscous damping. Therefore, the known solutions of the vibration equations were applied directly to the problem and the efficiency curves calculated. This solution technique, however, could not take into account the various geometric variations such as the jet-to-plate distance in the determination of the efficiency curves.The work of Ranz and Wong (1952) was later modified by Mercer and Chow (1968) and Mercer and Stafford (1969) so that the rather simple flow fields of Ranz and Wong (1952) could be used to account for various jet-to-plate distances. The same techniques, however, were used to determine the impactor collection efficiency curves."

Jan 1, 1986

By Margaret M. Ragin

In a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research, with input from the phosphate industry, the conversion of phosphogypsum to sulfur has been investigated. The first step in the conversion scheme involves reduction of phosphogypsum to calcium sulfide. Effects of temperature, catalyst, reaction time, and type of reductant (carbon monoxide and coal) are discussed. It was determined that phosphogypsum could be reduced to calcium sulfide at 850° to 1,000° C using either coal or carbon monoxide as the reductant. The required temperature was lowered to 750° C using ferric oxide or magnetite as a catalyst for the reduction reaction. Results indicate that as the volatiles content of the coal is increased, reaction temperature may be decreased to obtain a given conversion, or if the reaction temperature is maintained constant, the conversion can be increased. Best results were 95- to 100-pct conversion using a high-volatile coal at 800° to 850° C. Addition of a catalyst increased calcium sulfide yield when low- or medium-volatile coals were used as reductants, but had little effect when high-volatile coals were used.

Jan 1, 1990

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961

This part of the final report treats some problems related to coal mine carrier frequency communication systems using the trolley wire/track transmission line. This work was undertaken for a brief period of time during the summer of 1972 to help understand, quantify, and improve some of the trolley wire carrier system behavior observed and/or predicted. Calculations and estimates of transmission line characteristic impedance, inductance and capacitance per unit length, mine motor loading effects, parallel line effects, and connection impedances are presented in Chapter I. Chapter II treats the design of r-f isolators for reducing the undesired and troublesome r-f loading that mine motors present to the trolley transmission line. Chapter III treats a diversity method for combatting standing wave nulls. I. CALCULATIONS RELATED TO TROLLEY WIRE COMMUNICATIONS A. ESTIMATION OF INDUCTANCE AND CAPACITANCE PER UNIT LENGTH OF TROLLEY LINES To estimate the L and C per unit length of trolley lines, we use the eccentric line model of Section G of this Chapter, "Characteristic Imped¬ance Estimates for Mine Trolley Lines." The capacitance per unit length for an eccentric line is given by (1)

Jan 1, 1974

By T. G. Carnahan

The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100° to 110° C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HN03 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96 pct was achieved by this procedure.

Jan 1, 1979

By Linneas W. Laage

Coal production from underground coal mines has been important to the development of the industrial economy of the United States. Environmental problems have developed from some abandoned operations. These problems include: mine and refuse pile drainage, subsidence, unsafe mine openings and to a lesser extent mine gases, slope stabilities, mine and refuse pile fires and abandoned equipment and structures. Field investigations in three eastern coal mining districts, two in Ohio and one in Illinois, were performed to document the mine closure procedures used and subsequent problems that developed. The purpose was to identify, evaluate, and rank the seriousness of these problems. Based upon this evaluation, the undesirable present day situations could have been avoided or at least minimized by varying certain mining practices or mine closure procedures. It was found that federal regulations address all of these problems during the pre mining, active mining and post mining phases except for abandoned equipment which is the least threatening problem category. Ideally current practice would prevent future problems. However, the extensive and complicated nature of the legislation, environment and mining practices will necessitate adjustments to the law. The investigator recommends the following: 1) Goal oriented legislation encouraging complete resource extraction, standardization and compilation of mining generated hydrological data, periodic review of the coal mining regulations, and improved communication and cooperation between coal interests, regulators and the public. 2) Permitting effluent limitations to accurately reflect natural conditions. 3) Solidly back filling shafts and individual assessment of sealing or capping requirements. 4) Installing shaft vent pipes into the fill material to intercept and vent methane.

Jan 1, 1982

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 1992

By Paul Biggs

This Bureau of Mines report provides information on 138 waterflood projects in Wyoming. Injection was in 25 producing zones and 65 fields. Specific data presented include field location, discovery and development, water supply and injection, oil and water production, estimates of oil in place, and oil recoveries by primary and secondary methods. The 138 projects studied will, if successful, recover about 800 million barrels of secondary oil. Almost all of the injection water is from deep water wells.

Jan 1, 1970

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

By L. C. IlsLey

"Nearly every piece of electrical equipment used in mines ""breathes."" In other words, motors, controllers, rheostats, switches, and other similar equipment, even though encased in seemingly tight compartments, breathe in the atmosphere that surrounds them.As the apparatus is used, the temperature of metallic parts is changed generally in positive direction through the heat by friction and the heat due to the electric current. When the apparatus is idle it gradually cools down to the temperature of the surrounding atmosphere.This increase of temperature during operation and return to normal temperature when operation stops alternately raises and lowers the temperature of the atmosphere within the compartments which, in strict accordance with Charles' law -will expand or contract in proportion to any given temperature change.As compartments are not gas-tight, such expansion and contraction will force the atmosphere out of the compartment =on expansion and suck the surround¬ing atmosphere into the compartment during contraction, hence the term ""breathing.""Investigators2 of explosion-proof equipment have recognized that such an interchange would take place and have designed their equipment to safeguard possible explosions within the compartments."

Jun 1, 1927

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By H. E. Powell

A series of alkyl-dithiocarbamic acid amine salts was prepared and tested as collector for slimed lead minerals contained in the waste material from a commercial lead ore concentrator. The reagents, members of a homologous series differing only in the number of alkyl radicals in their structure, were prepared by reacting stoichiometric amounts of primary amines and carbon disulfide in a cold alcohol solution. Subsequent purification was by recrystallization from absolute ethyl alcohol solution. Evaluation was through froth flotation of a mill tailing containing 0.2 percent lead. Results show that maximum recovery (38 percent) was obtained with the reagent containing 8 alkyl radicals, but that maximum rougher concentrate grade (4.8 percent) was obtained with the reagents of intermediate number of radicals.

Jan 1, 1962

By J. G. Croeni

The high thermal-neutron cross section of gadolinium and the good mechanical and corrosion properties of titanium suggest that alloys of these two metals might be useful as control rod material. To aid in establishing the feasibility of this combination, the Federal Bureau of Mines investigated the titanium-gadolinium system. The results indicate that the system is composed of a single eutectic reaction and a peritectoid reaction involving the alpha-beta transformation of titanium. The eutectic isotherm extends from 1 to 99 pct, gadolinium at 1,240° C. The established eutectic composition is about 95 pct, gadolinium. The peritectoid reaction occurs at 885° C. and extends almost over the entire composition range. Hardness increases slightly with additions of gadolinium, and little change is obtained by heat treatment. Alloys containing less than 10 pct. gadolinium are amenable to extensive cold-working, but alloys having higher percentage of gadolinium content are only moderately cold-workable. All alloys can be hot-worked in iron sheathing at 750° C. Observation indicates that all compositions possess good machinability. Corrosion resistance to water at room temperature is apparently poor, especially in the gadolinium-rich alloys. INTRODUCTION A combination of the good mechanical and corrosion properties of titanium and the variety of thermal-neutron cross sections characteristic of the rare-earth metals suggests that alloys of these metals may be used for control rod materials. For this reason the Bureau of Mines proposed a study of the titanium-gadolinium alloy system, and the Atomic Energy Commission sponsored the investigation.

Jan 1, 1961

By Wilbur Duvall

For the past few years the Applied Physics Branch has been investigating, experimentally, the generation and propagation of strain waves in rock. The strain waves are produced by the detonation of a high-velocity explosive placed in a small cavity in the rock. Strain gages mounted in the solid rock surrounding the cavity record the strain pulses propagated away from the source. Numerous strain-wave pulses have been recorded in different rock types for charges of various sizes and at various distances from the charge. Analysis of these records has shown, among other things, that there is associated with the strain wave a characteristic pulse width. This pulse width is dependent on the rock type and the distance from the shot point to the gage, but is apparently independent of the charge size or cavity size. Recent published literature on the generation and propagation of seismic waves indicates that the characteristic frequency of an elastic wave generated by an explosion should be a function of the rock type and the size of the cavity created by the explosion. Also, internal friction in the rock would produce absorption of high-frequency components, which would cause continual change in the shape of the pulse propagated. As the experimental data did not verify the expected change in pulse shape with cavity size, a theoretical investigation of the vibrations associated with a spherical cavity in an elastic medium was undertaken.

Jan 1, 1950

By D. S. Kingery, F. F. Kopsch

The practice of using two or more main ventilating fans is common at large coal mines throughout the coal-mining industry. To assure adequate and efficient ventilation at may mines, such multiple-fan systems are necessary. The hazards associated with interrelated ventilating currents if a fan fails are controversial, and to date little effort has been made to study this specific problem and to determine corrective measures. The obvious questions are: 1. Is there a hazard? 2. Under what circumtances does it exist? 3. How serious is it? 4. What are corrective measures? Most members of the mining fraternity agree that reduced quantities of air and changed airflow patterns introduce potential hazards, especially where gaseous conditions exist when mechanized methods are used in concentrated mining 0 The seriousness of the hazard depends on the ease with which methane accumlates in face areas or haulage roads, the quantity of methane in workedout areas, and the extent to which reversed air currents interfere with escape and recovery operations after mine fires or explosions. These studies cover three mines and give the distribution of air for the specific conditions show. Each mine probably has somewhat different airflowpressure relationships between fans. This depends on the number of fans, the

Jun 1, 1959

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

By A. P. Grossman

'This report was prepared by Shell Oil Company, Mining Ventures Department in accordance with Cooperative Agreement No. 14-09-0070-b53 dated September 10, 1976, between the United States of America, Department of the Interior, Bureau of Mines and C(b) Shale Oil I Project, Ashland Oil Inc., Shell Oil Company, Operator. After completion of this report the Shell Oil Company withdrew from participation In the C(b) Shale Oil Project and advised the Bureau of Minus that plans for publication of this report had also been withdrawn. The Bureau of Mines acting under terms of the Cooperative Agreement hereby releases this report for general information.

Jan 1, 1976