Search Documents

By J. B. Gayle

The removal of coal particles from a slurry by flotation is made possible by the formation of stable aggregates with air bubbles of suitable sizes. The formation of such aggregates is theoretically possible only for certain favorable combinations of the solid-liquid-gas interfacial tensions. Because interfacial tensions involving solid phases are not conveniently measurable, a related variable, the contact angle, frequently is used as a measure of the floatability of various materials. Zero angles indicate nonfloatable substances, and large angles indicate substances having a high degree of floatability. During a study of contact angles for coal and substances related to coal in their similarity of response to various physical and chemical treatments, particularly flotation, carbonization, and oxidation, the reproducibility of replicate determinations taken within a 4-hour period was found to be much better than that for comparable results taken over a longer period of time. Consideration of possible causes for these differences led to an investigation of the effects of temperature variations on contact angles. References to literature revealed only a small amount of information, some of it apparently conflicting. Specifically, Sutherland and Wark4/ found that temperature variations "within limits" did not appreciably influence the angles measured for galena conditioned with potassium ethyl xanthate. On the other hand, McGlashan and McLeod5/ presented preliminary data showing that for sphalerite conditioned with potassium ethyl xanthate the angle is maximum at 25° to 35° C., depending on the pH of the system.

Jan 1, 1960

Develop a simple and economical technique for determining the absolute stresses and the change of stress on the surface of roofs, floors, or walls in miners. Approach Use a commercially-available, permissible, Whittemore-type gage to determine the stress at the surface of a mine opening and to monitor any stress changes that might take place. How It Works The following equipment is used: ? One steel templet (for laying out a 60° rosette on the: rock surface). See first photograph. ? One 3/8-inch rock drill bit for drilling holes for the rosette pins. ? Six stainless-steel rosette pins. ? One Whittemore-type mechanical strain gage. ? One drill (not shown). ? Epoxy for cementing the rosette pins. ? Tape to hold the pins while the epoxy sets. The following procedure is used to determine the absolute stress on the rock surface. 1) Spot the location of the rosette pins with the templet. 2) Drill the pin holes and set the pins with epoxy cement. 3) Measure and record the distance between the pins across three diameters of the rosette with a 10-inch Whittemore-type gage. See diagram. 4) Drill a 1 1/2-inch diameter hole in the center of the

Jan 1, 1981

By Charles L. Kimbell

Comprehensive data on market prices for crude minerals and mineral products for the world as a whole do not exist, and even the data that are available are not necessarily compatible between countries, particularly between the market economy countries and the centrally planned economy countries. Further, it should be evident that the actual delivered price for a small quantity of any specific commodity at some point substantially removed from a production facility or a seacoast port will differ appreciably from that for a large volume of the same product at or near its production source or a major import center. Nevertheless, the regularly published prices of selected major mineral commodities in key market areas can be regarded as indicative of general world price trends.

Jan 1, 1992

By F. P. Miknis

Previous studies at the Bureau of Mines have shown that broad-line nuclear magnetic resonance (NMR) techniques have potential applications for rapid evaluation of oil-shale deposits. In a continuation of this study the techniques of pulsed NMR have been applied in a similar manner. The basis for the pulsed NMR oil-shale assay method lies in the assumption that the free induction decay (FID) amplitude following a 90° pulse is proportional to the potential oil yield. This assumption was tested on two groups of oil-shale samples, numbering 141 and 263 samples, from two different oil-shale cores. For both groups of samples a small number were selected as calibration samples. Free induction decay amplitude measurements were made on the 141 and 263 samples. The best least-squares regression line was obtained for the calibration samples, and the oil yields of the remaining samples were calculated using the slopes and intercepts obtained in the regression analyses. The agreement between measured and calculated oil yields was good, the indexes of determination being 0.93 and 0.89 for the groups of 141 and 263 samples, respectively.

Jan 1, 1974

By N. E. Hanna

Experience with the current version of gallery test 4, in use since 1913 to evaluate the incendivity of permissible explosives in the presence of coal dust, has shown the procedure to have inadequate discrimination. Consequently the Bureau of Mines used the up-and-down method of statistical design to investigate the incendivity of permissible explosives in the presence of coal dust and gas. A suitable device was developed to measure coal dust concentrations in the air-gas mixtures and to disperse the dust in the gallery atmosphere. A proposed testing method which uses suspended shots in a predispersed coal dust-gas-air mixture was evaluated. The new method can discriminate between different explosives with respect to their incendivity. Maximum ignitibility of the coal dust cloud by permissible explosives occurred in the vicinity of 0.3 oz/cu ft. About 10% sodium chloride in permissible explosive formulations had a very significant effect in reducing the probability of igniting coal dust. Bundled charges were more incendive than column charges.

Jan 1, 1966

By James A. Powell

A seismic system which utilizes in-mine geophones to detect trapped miners has been developed. Tests at the Bureau of Mines Safety Research Mine at Bruceton, Pa., and at two operating mines indicate such a system has a maximum detection range in excess of 1,000 feet. The system is fieldworthy and portable and requires less than 30 minutes to set up and check. Real-time detection is possible.

Jan 1, 1976

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By Jr. Kauffman

The data contained in this report were obtained incidental to the Bureau of Mine's investigation of the lime-soda sinter process as applied to the recovery of alumina from siliceous bauxite, kaolin, and other high aluminous materials. The Bureau of Mines was charged by Congress to investigate processes for the production of aluminum from domestic low-grade ores. The Eastern Experiment Station at College Park, Md., conducted laboratory and pilot-plant investigations of the recover-y of alumina by the lime-soda sinter process. Reports by the College Park staff covering the recovery of alumina from these sources have been published. The lime-soda sinter process involves the sintering of the finely ground siliceous bauxite or clay with limestone and soda ash in a rotary kiln. During the sintering the alumina supposedly reacts with the soda ash to form soluble sodium aluminate and the silica combines with the lime to form the insoluble orthosilicate. In the early stages of the investigation it was considered desirable to know the temperatures at which the phase changes occurred during the sintering operation. The total time involved in the passage of any given portion of the charge through the kiln was 28 minutes. The exposure time of the charge to temperatures above 600° C. (decomposition temperature of kaolinite) was, roughly, half the total. The exposure to the full temperature of the kiln, 1,100° C was only 3 minutes. (Subsequently, the maximum kiln temperature and retention time were increased.)

Jan 1, 1949

By D. C. Dahlin

The Bureau of Mines conducted laboratory batch beneficiation tests on samples from four potential platinum resources in southeastern Alaska to concentrate platinum and other precious metals. Thin Investigation was done as part of the mission of the Bureau to insure an adequate supply of minerals to meet the Nation's needs. Petrographic studies and beneficiation methods including gravity concentration, froth flotation, and magnetic separation were used to determine mineral association and to attempt to concentrate the platinum values with a primary mineral value such as chromite, copper sulfide, or magnetite. A high-graded sample from the Salt Chuck copper sulfide deposit yielded the platinum-group metal concentrate; the maximum grade attained was 0.04 oz Pt and 1.5 oz Pd per ton of high-grade copper sulfide concentrate. The other samples yielded low-grade primary mineral concentrates with low platinum-group values, and/or the platinum-group metals did not concentrate with the primary mineral value.

Jan 1, 1981

By E. L. Rawlins

A previous report4 has explained that pipe lines for the transmission of natural gas should be buried to minimize temperature fluctuations because when excessive the latter decrease accuracy in measuring gas volume and increase leakage of gas due to expansion and contraction in the pipe joints. These effects are governed by the rapidity of the temperature fluctuations and by the total variation over a period of time. The temperature of gas flowing through a pipe line depends to a large extent, upon the temperature of the ground adjacent to the pipe; hence, fluctuation of the ground temperatures at various depths determines the economic depth at which pipe lines should be buried. Scope and Purpose of Report This report covers a record of the daily atmospheric temperature fluctuations at Bartlesville, Okla., for 12 months and a-similar concurrent record of the temperature variation 1, 2, 3, and 4 feet below the surface of the ground.

Jan 1, 1928

By L. A. Johnson

The Bureau of Mines analyzed three cores from the south Seep Ridge area of the P. R. Spring tar sand deposit of northeastern Utah. Four tar sand zones are indicated in the area. The zones range in average thickness from 13 to 24 ft. The total net thickness of the tar sand in the three coreholes ranges from 71 to 112 ft. The tar sand occurs between the depths of 27 and 254 ft. It has good porosity, 25.6 pct of bulk volume; high permeability before and after oil extraction, 819 and 2,218 md, respectively; but a relatively low oil saturation, 36.5 pct of pore volume. Gravity of the oil ranges from 8.20 to 16.5° API.

Jan 1, 1975

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By Jay D. Dixon

The Bureau of Mines has developed structural design data for unreinforced concrete tunnel linings for drifts used in block caving stopes. Design data are given that consist of moment, thrust, and deformation coefficients from which bending, axial, boundary stresses, and structural deformations can be determined at any point on the lining. Data is given for circular, horseshoe, and rectangular linings, each with two different thicknesses and subjected to eight different loading conditions for drifts excavated in hard and soft rocks. The structural analyses performed are based on procedures that account for both the structural behavior of the lining and that of the drift and take into consideration deformational interaction that occurs between them.

Jan 1, 1973

By Albert L. Brautigam, Michael C. Leigh, August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 1992

By Stuart Lipoff, John E. Trombly, Paul Brien, O&apos

System objectives and design criteria for an in-mine ULF radio paging system are discussed. Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

By William Hustrulid

The National Institute for Occupational Safety and Health (NIOSH), as part of a comprehensive program to improve mine safety through the widespread acceptance of careful excavation principles in drifting, have revisited standard drift round design concepts. Although the initial emphasis was on contour row design and providing improved design tools for blasting with de-coupled charges, the focus has broadened into the development of a general gas pressure-based drift round design approach. The concept of a damage radius (Rd) for a given explosive-hole-rock mass combination is introduced. With the damage radius as the basic building block, the blast holes are positioned on the face, beginning with the buffer row, to achieve the desired excavation size, shape and smoothness. The design of the contour row of holes is also performed using a pressure-based approach. The paper presents in some detail the overall approach and the required gas pressure-based design equations.

Jan 1, 2007

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Japan has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State . It is based on the law and regulations of 1905 as revised in December , 1915 , and translated by J. de Becker , LL.B. Occasional words and phrases quoted herein are accordingly taken from this translation and have not been checked against the original . The references are to the law ( as distinguished from the regulations ) unless otherwise stated .

Jul 1, 1930

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976

By T. A. Gray, L. M. Crayne, P. Glogowski, Trevits. M. A.

Of the 19 major mine fire events (including thermal events) that have occurred in the last 6 years (2000-2005), it is estimated that remotely constructed mine seals could have been used at 65% of the events to control or suppress the fire. Underground observations of seals that have been remotely installed during mine fire events show that they often do not fully achieve mine roof-to-floor and rib-to-rib closure. Unfortunately, the inability to reliably close the mine void has limited or precluded the regular use of this technology. The National Institute for Occupational Safety and Health is conducting full-scale underground experiments at the Lake Lynn Experimental Mine to identify and remedy existing remote sealing technology shortcomings, to develop novel technologies, and to transfer the new or improved technologies to the mining industry. This paper will discuss the remote mine seal testing program and will provide the results of the in-mine experiments. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.