Search Documents

By Anthony T. Iannacchione

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By E. L. Burwell

Application of the in situ recovery process to oil shale was tested during two field experiments near Rock Springs, Wyo. The results of these tests demonstrate that a self-sustaining combustion zone can be created in an oil shale body, that this zone can be moved through the oil shale, and that the process will produce shale oil. Evaluation of the combustion process by monitoring produced fluids for physical and chemical properties and volumes is described. The material and energy balance obtained is compared with a second evaluation based on extensive coring of the test area after the test was terminated. Several side results of the research are noted such as ground surface heating by underground burning and production of low-to medium-Btu gas during retorting.

Jan 1, 1973

By F. P. Haver

The Federal Bureau of Mines investigated aqueous electrolysis as a means for reducing lead chloride prepared by ferric chloride leaching of galena concentrate: NaC1 PbS + 2FeC13 ? PbC12 + 2FeC12 + S°. During electrolysis, metal was produced from solid lead chloride in contact with the cathode rather than from lead in solution. Relatively high current densities--up to 300 amp/ft2--were possible when operating in this way. A very simple cell, having a horizontal lead cathode at the bottom and a vertical graphite anode at the top, was employed. Lead chloride crystals, covering the cathode, were converted to metal powder during electrolysis, and chlorine gas or FeCls was produced at the anode, depending on the electrolyte composition. Electrolytes tried included aqueous solutions of HCI, NaCl, NH4Cl, and FeC12-NaC1. Optimum results (96-pct current efficiency, 0.23 kwhr/lb Pb) were obtained with 20 pct HC1 at 25° C, using a current density of 15 amp/ft2 and an electrode spacing of 1 inch. When the current density was increased, the energy requirement increased also but only to 0.41 kwhr/lb at 150 amp/fr3 and 0.58 kwhr/lb at 300 amp/ft2.

Jan 1, 1978

By R. S. Dean

The principle of explosive crushing depends upon the fact that an expandable substance contained within the pores of a solid body will disrupt such a body upon expansion. Such expansion may be obtained by the detonation of an explosive or by the sudden release of pressure of a superheated liquid. That this principle of disruption may be applied to minerals rests on the fact that cracks, cleavage planes, and pores exist in all mineral to an extent hardly conceived possible heretofore. Crushing by this method takes advantage of force applied from within the mineral rather than from forces applied from without. The application of a force from within would appear to be more effective. A consideration of the possibilities of such a method for crushing led to some experimental work of a preliminary nature, the results of which are embodied in this paper. No systematic program was followed in the work and the results are, therefore, not final and far from complete. The success attained so far, with the mediocre apparatus available seems to warrant a preliminary report, with the expressed hope that the work may be carried on as well-outline program covering such phases as have been impossible to investigate at this time.

Jan 1, 1931

By Frank W. Sansom

This paper is one of a series of articles dealing with milling methods and costs at metal mines in the United States, written in accordance with an outline prepared by engineers of the United States Bureau of Mines and published by the bureau. The Netta mine and concentrator is the largest of the plants of the Eagle-Picher Lead Co, It is located in Ottawa County, in the extreme northeast corner of Oklahoma, and in what is known as the Tri-State zinc and lead mining district, embracing the northeast corner of Oklahoma, the southwest corner of Missouri, and the southeast corner of Kansas. A majority of the production comes from the Oklahoma section, with Kansas second, and Missouri third.

Jan 1, 1930

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite having length to diameter ratios of 3:1, 2:1, 1:1, and 0.5:1 were broken in axial compression to determine whether lateral end constraint affected the breaking strength. Steel rings bonded to the ends of the model pillars with epoxy provided, during the loading cycle, a lateral end constraint of about 17 to 30 percent of the average axial stress. The effect of this constraint was to increase the breaking strength of the rock as compared to cylindrical pillars without constraint. The percentage increase in breaking strength varied with rock type and increased as the length to diameter ratio decreased. The maximum increase in breaking strength was 35 percent for marble pillars having a length to diameter ratio of 0.5:1. A theory was developed which relates the expected constraint to the physical properties of the ring and rock.

Jan 1, 1968

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By Charles W. Huggins

DEVELOPMENT of the electron microscope has permitted man to examine many small objects that could not be resolved by the light micro-scope. Diffraction, spherical aberration, and chromatic aberration are the main factors that limit resolution to about two-tenths micron with the light microscope. No matter how perfectly a light microscope is constructed and operated, it cannot possibly resolve points separated by less than two-tenths micron. Rapid development following World War II has produced many electron microscopes capable of 20 A resolution. Fibrous inorganic minerals are well suited for electron microscopic study. Many micrographs of chrysotile have been published, but electron microscopic study of the amphiboles has been somewhat neglected. New techniques in sample preparation have simplified the study of fibrous material. Ultrasonic energy has been very helpful in sample dispersion. This publication contains a representative group of electron micrographs of natural inorganic fibers that have industrial value. These fibers commonly are referred to as the asbestiform minerals. The Bureau hopes that the knowledge gained through electron microscopy and other scientific study of the natural inorganic crystalline fibers eventually will lead to the production of synthetic fibers that will satisfy the requirements of industry.

Jan 1, 1959

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

Provide a full-scale test facility where the effectiveness of all types of subsidence abatement techniques can be evaluated under controlled conditions. Background Subsidence is ground movement resulting from the collapse of overlying strata into a mine void because of failure of the mine roof, mine floor, or support pillars. The failure may propagate to the surface and be expressed as a depression, cracks, or a sinkhole. The surface expression of such features may be delayed until long after mining has been completed. Subsidence has the potential to affect more land area than any other type of abandoned mine land problem. Subsidence also causes direct damage to real property, with significant financial loss and more importantly, presents a danger to public health, safety, and general welfare. Subsidence-related problems are considered to be one of the most important abandoned mine land issues. Backfilling of mine voids is the most common stabilization method used to abate subsidence and protect surface structures. Backfilling or placement of material is performed by hydraulic flushing or pneumatic stowing, using either in-mine or remote methods. The majority of the past subsidence abatement projects has been performed using remote methods from single or multiple boreholes. Other subsidence abatement techniques arc available. For example, various point support methods are used to protect small areas of the land surface and surface structures, without completely filling the mine void. These may be more appropriate under different conditions. Little documented information is available concerning the capability of the various backfilling methods for completely filling a mine void or providing long-term structural strength. Therefore, the Bureau of Mines developed a laboratory for controlled evaluation of backfilling technologies.

Jan 1, 1991

By G. E. McClelland

The Bureau of Mines investigated chemical methods for producing high- purity gold from precious-metal-bearing zinc precipitates and steel wool cathodes. Precious-metal-bearing zinc precipitates and steel wool cathodes are unrefined products from conventional cyanidation and heap leaching-cyanidation operations. The zinc precipitates contained 14,40 pct Au and 0.35 pct Ag. The precious-metal-bearing steel wool cathodes contained 20.65 pct Au and 4.84 pct Ag. The precipitates and cathodes were treated with dilute acid to solubilize the silver and/or base metals. The gold-bearing residue was leached in dilute aqua reqia to solubilize the gold. High-purity gold was precipitated from the aqua regia solution with oxalic acid, sulfurous acid, sodium bisulfite, and gaseous sulfur dioxide. The leaching-precipitation experiments recovered 99.9 pct of the gold. The gold precipitates ranged in fineness from 997 to 999 fine. The chemical refining method provides a viable technique for the smaller operator to produce high-purity gold without using pyrometallurgical refining methods.

Jan 1, 1985

By GEORGE S. POPE

The purchase of coal by the Government under specifications depending on the heating value of the coal, its content of ash and of moisture, and other considerations, rather than upon the reputation or trade name of the coal, was based on the fuel investigations begun by the Technologic Branch of the United States Geological Survey in 1904. The plan was first adopted by the Treasury Department in 1906. Since then the plan, variously modified in form but the same in principle, has been gradually adopted by other departments until at present of the coal used by the Government, the total value of which approximates $8,000,000 annually, more than half is purchased under specifications. The Government publications dealing with the adoption by the Government of the specification plan, the number of contracts awarded on that basis, and the quality of the coal delivered under such contracts in the several fiscal years covered by the reports are given in publications listed at the end of this bulletin. Under the authority of acts of Congress making appropriations for analyzing and testing fuels belonging to or for the use of the United States Government, a laboratory is maintained at the headquarters of the Bureau of Mines, Washington, D. C., where samples represent- ing deliveries of coal purchased under specifications for Government use are analyzed and tested. At this laboratory more than 1,200 samples have been analyzed and tested in one month. With the complete equipment and the efficient force employed, the analytical work has been so perfected that the analyses and heating-value tests of the samples received are as accurate as may be reasonably expected in laboratory work of this nature. One of the serious drawbacks to the general adoption of the speci- fication method for the purchase of coal is the difficulty of obtaining at reasonable cost samples of coal that can be considered fairly repre- sentative of the commercial product delivered in wagons, railroad

Jan 1, 1913

By John S. Dunning

This paper is one of a series describing methods and costs of recovering sand and gravel from deposits in the United States and deals directly with the operations of the Atlas Sand, Gravel and Stone Co. at Farmington, Conn. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs might in some instances cause embarasement to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue.

Jan 1, 1933

By G. R. Hopkins

[ ]

Jan 1, 1927

By Roy L. Wilfong, LeRoy R. Furlong, Louis P. Domingues

The bulk and apparent densities , particle size , and surface area of ceria powders derived from the ammonium sulfate , carbonate , nitrate , oxalate , and sulfate salts and heated at 950 ° to 1,500 ° C for 1 to 24 hours were studied . The bulk and apparent densities and particle size generally increased , and surface area decreased with increase in temperature and time of heating ; surface area was more sensitive to changes in temperature and time than the other properties studied . These properties of the ceria powders had a marked dependence on temperature and a lesser dependence on duration of heating at a given temperature ; and the source of oxide and thermal treatment cannot be considered optional in the preparation of refractory powders by thermal decomposition . The ammonium sulfate and sulfate salts heated at 950 ° and 1,200 ° C produced oxide powders with the lowest bulk density , the smallest particle size , and the highest surface area . The highest apparent densities were achieved for oxides resulting from the carbonate and the sulfate but the carbonate - derived material was considerably coarser . The surface areas of ceria powders derived from cerium salts decrease in the order of sulfate , ammonium sulfate , nitrate , oxalate , and carbonate . The observation of these physical properties are useful in predicting the sintering behavior of various oxide powders .

Jan 1, 1964

One of the major unknowns in the use of iron and copper is the quantity of various low level impurities, particularly hydrogen, that may be introduced during the deoxidizing process prior to casting. Introduction of hydrogen results in the embrittlement of components made from these metals. In addition, hydrogen bubbles in castings of copper result in the formation of blisters and swelling of the casting. During the last year, a significant effort has been made at the University of Missouri-Rolla to understand the permeation of hydrogen in galvanized automotive steel components and the hydrogen absorption during the electrodeposition of copper. The galvanized steel components consisted of automotive upholstery clips, seat belt holders and brake clips. Although the process of galvanization protects the steel from corrosion the process invariably causes the steel to pick up enough hydrogen to make it susceptible to brittle fracture.

Jan 1, 1992

By R. E. Head

"The microscopic work described below was engaged in primarily into ascertain the approximate proportions in which the copper sulphides existed in the ore examined, and by a comparison of the results obtained from a study of both head are tailing samples to supply data which might be of value in treating the ore by flotation. Incidentally, the physical characteristics and association of the sulphides were noted in order to determine the possible relation or bearing of these features on the present conditions of treatment. Since the copper in the ore occurred as three distinct sulphide minerals - chalcopyrite, chalcocite, and bornite each containing copper in different proportions, there appeared to be little or no possibility of obtaining the desired information by chemical methods of determination.Type of material examinedThe material examined was in the crushed condition and was said to be representative of the flotation feed or heads and the resulting tailing. No hand samples of the ore were examined nor any account taken of the physical condition and association of the minerals in place, because the possible value of the analytical results depended on conditions as they existed in the crushed ore. As the problems under consideration dealt only with the sulphide minerals, especially those of copper, the products from screen sizing were concentrated by hand panning and the gangue discarded. The concentrate obtained consisted almost entirely of the sulphide minerals, since the panning had been very carefully done. The object of this procedure was to obtain a sufficient quantity of high-grade sulphide material, from the sample of each screen size selected for examination, to permit its being so prepared for examination as to be representative of the physical characteristics exhibited by a large number of sulphide grains from each respective size, In the tests and investigations carried on by the company' treating the ore the following sizes had been used in tabulating data and basing conclusions:+48, +65, +100, +150, +200, and -200. These same sizes were used in the microscopic investigation, since the results obtained thereby could be most readily utilized for comparison with the results obtained in previous experimental work, together with deductions based on actual concentration of the ore on a commercial scale."

Jun 1, 1921

By R. E. Tremoureux

This paper describing the methods and costs of quarrying limestone at Sloan, Nev., is one of a series of similar papers being prepared for and published by the Bureau of Mines on this industry in the United States. These papers are designed to disseminate information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods Employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The quarrying operations at Sloan are interesting not only from a technical viewpoint and because of the magnitude of the deposit, but also because the quarry is located in a desert region far removed from the centers of population where lime is used. The quarry and plant are in Clark County, Nev., 20 miles west of Las Vegas, which is the nearest town to the site of the Boulder Canyon Dam. Sloan is on the main line of the Union Pacific Railroad connecting Salt Lke City and Los Angeles. The latter city is 280 miles from Sloan and it is the shipping, point for all supplies.

Jan 1, 1932