Search Documents

By Elton L. Litchfield

The techniques for direct initiation of detonation, developed by the Bureau of Mines, have been applied to gaseous mixtures of oxygen with methane, 'thane, propane, butane, or hexane. An exploding wire was used as the initiation source to determine minimum stored electrical energies required to effect detonation of mixtures between one-half and two times the stoichiometric fuel ratios. Detonations were obtained in the most easily initiated mixtures of ethane, propane, butane, and hexane for initiation energies between 24 and 33 joules at 1 atm and 28-43 joules at 0.5 atm initial pressure. Methane mixtures, at 1 atm, were not observed to detonate when initiated with up to 484 joules.

Jan 1, 1966

By George R. McCormick

Because several new and unusual synthetic minerals were found in the system MgO-MgF₂ - SiO2 with Li * , or Nat a similar system with Geo₂ replacing Sio , plus Lit was investigated . In addition to the expected compounds of germanium , Ge - fluor - hectorite and a Ge - fluor- chrysotile were synthesized . Protoamphibole was not observed . Data are given for 69 compositions prepared in the system MgO- MgF₂ - Ge02 at 6.94 percent LiF .

Jan 1, 1964

By Changwoo Lee, Jan M. Mutmansky

"This paper results from the research at The Pennsylvania State University into establishment of standard procedures for characterization of respirable coal dust performed by the Generic Mineral Technology Center for Respirable Dust and supported by the U.S. Bureau of Mines and the Mining and Mineral Resources Research Institute at The Pennsylvania State University. The research performed within this particular project is oriented primarily toward standard methods of sampling and characterizing respirable coal mine dust underground so that the chemical, physical, and morphological characteristics are known and can be related to the incidence of coal workers' pneumoconiosis (CWP) in Pennsylvania.The research was initiated by con¬ducting a search of the literature to determine what coal and geologic variables may be related to CWP. The effects of coal rank, free silica content, the mass of respirable dust, and the level of trace elements were the major variables studied. It seems to be evident that the free silica content, the rank of coal, and the mass of respirable dust are the major concerns in defining the causes of CWP. However, based on the literature survey, the authors have concluded that verification of the causes of CWP is a multivariate problem and must be analyzed in an appropriate statistical manner.The results of a multivariate analysis of ten trace elements recorded on Pennsylvania coals are presented. Five of these trace elements were found to be of use in differentiating one coalfield from the others. Of these five elements, chromium and zirconium showed a strong positive correlation with the rank of coal while strontium showed a negative correlation.The design of the field sampling work and its application in future research is the final topic discussed. The sampling plan is oriented toward continuous miner sections with eight-stage impactors as the collection equipment. All of the field work will be conducted in the coal measures of the Allegheny Formation and above with both dust and channel samples being collected in the same mines.Coal workers' pneumoconiosis has been an important topic of concern to miners, mining engineers, and epidemiologists for decades. The general cause of the dis¬ease, the inhalation of coal mine dust, is well known, but the specific coal and geologic variables that affect the incidence and severity of the disease are still subject to debate and study. The primary objective of this study is to identify those variables of Pennsylvania coals that contribute to the CWP problem. To accomplish this task, a field sampling program is to be conducted to relate the characteristics of the coal dust, the coal seam properties, and the geologic variables to the occurrence of CWP.The first year of this study has been involved with both a literature review and experimental work oriented toward identification of causal variables related to CWP. The results of this work are presented here along with plans for implementation of the findings in future research.The previous studies of CWP causal variables have been conducted by scientists, engineers, and medical personnel. Many different types of studies have been performed with emphasis on interpreting the effects of dust mass concentration, mineralogy of the coal, the rank of the coal, and trace element concentrations upon the incidence of CWP in various coalfields. Most of the research has been conducted during the last two decades, with the British Isles, West Germany, and the United States being the primary countries involved.The review of the literature was conducted to determine which variables are likely to warrant further study in Pennsylvania. Previous research studies have related CWP to free silica and other mineral content, the rank of coal, the mass of dust in the working place, and the trace elements in the coal and lung dust. In the following sections, each of these topics will be discussed and analyzed."

Jan 1, 1988

By R. V. Ramani

This volume is the third of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume II: Dragline Model, and Volume IV: User's Manual for OPMHS/2. The Mine Coordinate Generator System serves as an interface between the Geology and Reserves System (Volume I, final report) and OPMHS/2 (Volume IV, final report) to provide local mine grid information which is used as input to the decision making process and dynamic simulation routines of OPMHS/2. After the Geology and Reserves System has been successfully run for a property, a data base containing values for each grid cell covering the property is created at the end of execution, if chosen as an option by the user. The Mine Coordinate Generator reads this information and creates a special direct access data set from the sequential data input. When information defining the mine grid is read, the values present in the property grid are for the interpolation of values for each mine block.

Jan 1, 1985

By R. V. Ramani, P. M. T. White, D. Sutton

6.1 Summary This report deals with the investigation carried out to select, test, and implement a method of evaluating coal deposits and reserves. Cognizance is taken of the inherent characteristics of coal and the legislation covering aspects of health, safety, environment, and ecology applicable to the coal mining industry. Further, the method is computerized and provides information that is meaningful and readily available to other programs and sub¬systems within the concept of the Master Design Simulator. The Geology and Reserves Sub-system interface with the total system is provided by a geological data library which is structured to hold and make accessible all the data required by the system. The output from the program is accurate and useful to users with a wide variety of computer experience, knowledge, hardware and storage capacity. The sub-system is designed to function as a separate unit or an integral part of the total system and, there¬fore, an interface to or with the system has been established. The work carried out by the sub-system includes: (a) The analysis of raw geological data. This involves:

Jan 1, 1974

By G. S. Scott, G. W. Jones

Trichloroethylene (CHC1CC12) is an important solvent for fats , resins , bitumens, rubber , sulfur , and phosphorus . It is used extensively in drycleaning because of its low order of combustibility and has recently been proposed as an inhalation anaesthetic . Its physical properties have been described by Carlisle and Levine . It is usually considered a noninflammable material ; however , substances that are noninflammable when mixed with air are not necessarily noninflammable when mixed with oxygen . Thus , Hewer's statement that " Trichloroethylene*** is not inflammable under any circumstances , nor will its vapor explode when mixed in any proportion with air , oxygen, or nitrous oxide , " requires qualification , especially in anesthesia, where pure oxygen may at times be substituted for air , This report gives the results of tests made to determine the inflammability of trichloroethylene in various mixtures of oxygen and nitrogen . The trichloroethylene used was Eastman's No. 1300. The boiling point was given as 86 ° to 87 °C . The specific gravity and refractive index of the sample measured in this laboratory were , respectively, 1.45 and 1.4759 at 25 °C .

Nov 1, 1942

By R. T. Johansen

The adverse effects on waterflooding and well-completion methods of clay minerals indigenous to petroleum-production formations recently have received considerable attention. Knowledge of the types and amounts of clay minerals present would allow estimates of the response of such formations to injected or infiltrated water; however, the random distribution of clays in sedimentary formations makes direct evaluation of ?water sensitivity? desirable. A method for the direct evaluation of water sensitivity has been developed, based on measurement of water-vapor adsorption. Correlation of such data with the results of nitrogen-adsorption measurements provides valuable information on the content and properties of clay minerals in sedimentary rocks. The method is relatively simple and has the advantage that it may be used with small, irregularly shaped chips or shale-streaked samples, as well as with typical core samples. Methods previously employed required separating the clay from the rest of the reservoir-sample material and then performing a clay analysis either by X-ray diffraction, differential thermal analysis, liquid permeability, or a combination of these methods (2,3) .3/ This water-vapor-adsorption method requires measuring only a few points on the isotherm to tell whether or not the sample is water sensitive. The goal of these measurements is not to determine the type or amount of clay present, but what will be its sensitivity to flood water. This method gives a direct means of solving this problem.

Jan 1, 1958

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990

By J. E. Murphy

Purification of samarium metal by sublimation and by vaporization from a low-melting metal flux, at the same temperature, were compared. Vaporization proved more effective for removing impurities such as magnesium, calcium, and manganese. Recovery of samarium, however, is more rapid by sublimation because of its constant rate of distillation.

Jan 1, 1970

By M. J. Kovalik

The effects of the process variables on the production of chemical coke on a chain grate stoker, a type of traveling grate, were studied. Six bituminous coals, ranging in volatile matter from 16.7 to 43.8 percent, were successfully carbonized, yielding chemical coke with acceptable physical properties. The coke yields were dependent on the volatile-matter content of the coal. The air fuel ratio had the most marked effect on the yield and characteristics of the resultant coke, and the general furnace performance. Results can only be predicted; the actual yield and quality of coke obtained from any given coal can only be determined by actual tests using the optimum processing variables to obtain a coke with minimum volatile-matter content and to retain as much of the fixed carbon in the original coal as possible.

Jan 1, 1967

By Everett A. Sondreal

Data are presented on the characteristics of lignites with emphasis on the composition and fusion properties of the ash. Differences in the analyses of commercial-grade lignites are related primarily to variations in moisture and ash contents. Lignite ash is generally characterized by high concentra¬tions of alkaline earth oxides and a greater tendency for retention of sulfur in the ash than higher-rank coals. Composition of ash varies significantly within and between mines. The differences within mines are significant for short distances and may be eliminated under certain circumstances by normal mixing occurring during mining. The sulfur in lignite averages 0.6 percent and is found primarily in the organic or pyritic forms with only a trace of the sulfate. During the stan¬dard laboratory asking procedures, from 60 to 100 percent of the original sul¬fur is retained in the lignite ash. Trace elements, such as uranium and germanium, in the ash from commercial¬-grade lignites are present in low concentrations, but others, primarily copper and silver, are present in specific samples in concentrations approaching those found in some commercial ores.

Jan 1, 1968

By J. E. Tress

The Bureau of Mines has developed a process to utilize waste heat from electric arc steelmaking furnace gases to preheat the ferrous material charged to the furnace. Four heat exchangers were designed, tested, and operated successfully on 1-ton electric arc furnaces. Briquets and pellets were charged continuously, both countercurrent to the hot furnace offgasses and at ambient temperatures. A comparison of the electrical energy consumed in each situation showed that preheating can lower energy requirements as much as 15.6 percent.

Jan 1, 1975

Pillar design is the first line of defense against rock falls—the greatest single safety hazard faced by underground coal miners in the United States and abroad. To help advance the state of the art in this fundamental mining science, the National Institute for Occupational Safety and Health organized the Second International Workshop on Coal Pillar Mechanics and Design. The workshop was held in Vail, CO, on June 6,1999, in association with the 37th U.S. Rock Mechanics Symposium. The proceedings include 15 papers from leading ground control specialists in the United States, Canada, Australia, the United Kingdom, and the Republic of South Africa. The papers address the entire range of issues associated with coal pillars and have a decidedly practical flavor. Topics include numerical modeling, empirical design formulas based on case histories, field measurements, and post failure mechanics.

Jan 5, 1999

By Murray Jacobson

The respirable dust standard in the Federal Coal Mine Health and Safety Act of 1969 is designed to prevent disability and death from coal workers' pneumoconiosis. Beginning June 30, 1970, the operators of coal mines were required to maintain the average concentration of respirable dust in the active workings at or below 3.0 milligrams of dust per cubic meter of air. The standard is reduced to 2.0 milligrams per cubic meter after Dec. 30, 1972. This paper presents the equipment and procedures used by the coal mine operators in implementing the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare and shows the effect of the law, during the first year, on the reduction of dust levels in selected mines. The system employed by the Bureau of Mines for analyzing and processing the dust samples is also presented.

Jan 1, 1971

By Charles Findlay, Stephen Krickovic, J. E. Carpetta

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

By C. J. Johnson, C. J. Bise

"IntroductionCoal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation· s deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only af1er ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental composition of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines.There are several potential contributions of this type of study to the coal mining industry. First after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies.Further, assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location a mining company could predict anew mine's respirable dust elemental composition In the immediate ventilation return by using exploratory drill core samples of the roof ,coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design, much time and money could be saved.Scope of workTo investigate the variability of the chemical characteristics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and mid western United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee ( 1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs."

Jan 1, 1989

By C. Lorimar Colburn

"The use of helmets during the war has accentuated interest in the advisability of using stiff hats in mines to protect the miners against falling rocks. About forty per cent of the accidents in mines are due to falling rocks or roof. A large number of these accidents could be prevented if the miners wore stiff hats or helmets.The use of head protective devices in minas is not new, for they have been in use for many years in Europe and in the Lake Superior District in the United States. In practically all of the mining districts in Europe stiff hats of some kind are required by the mine management. George S. Rice, chief mining engineer of the Bureau of Mines, reported that in Germany, Belgium, and France stiff hats made of papier mache or felt rosin are in use. Similar hats are generally employed in the Lake Superior District. In building the subways of New York and Philadelphia it was the practice of engineers and workers to let the hair grow very long and to wear a close fitting cap or felt hat. In Germany the hats are high like the military helmets, whereas in France and Belgium they fit more closely to the crown. In England the practice is mixed. As a rule the miners use soft padded caps, but in Yorkshire many of the miners use sole leather, tight-fitting caps of jockey pattern with the seam forting a little ridge down the middle of the cap. These hats are very useful allow thin beds of coal, as in crawling one is very likely to strike his head a sharp piece of rock or on a timber. Of course, such mishaps are more likely to occur to a man not familiar with the mine. It must be admitted such hats do not stick on well, though this is usually due to their not being especially fitted. The German hat is particularly unsuited to an American-shaped head.It is interesting to note that on the continent tight cotton caps are generally worn over the hair and under the hard hat. This is a measure for cleanliness which is excellent. In low beds of coal share much crawling on hands and knees is necessary the dirt and coal dust sift down, making the miner black and dirty. In metal mines stiff hats are of especial use in shaft work; also in raises or high stapes. A small fragment of rock falling some distance either down a shaft or raise would kill a man if it struck him squarely on the head. A stiff hat or helmet may protect him and save his life. At a station in a shaft where men are loading the cage or skip, some kind of adequate head protector should be compulsory. A head-protecting hat or cup which is also a good insulator should be worn where there is danger of striking one's head against a wire carving an electric current."

Jun 1, 1920

By H. C. Ko

As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the standard enthalpies of formation for ZnO?2ZnSO4 and COS04-6H20 were determined by HC1 acid solution calorimetry. The values are -550.31 ±0.28 and -641.33 ±0.15 kcal/mot, respectively.

Jan 1, 1982

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By Eugene V. Cilento, R. Clark Lantz, K. A. DiGregorio

"This laboratory bas developed a sensitive electro-optical method to quantify the initial rate (R) and total amount (MAX) of superoxide (02) produced by single pulmonary alveolar macrophages (PAM). The method uses a microscope-based TV system to visualize PAM in culture, and to video record the images during the time the cells produce 02. MAX and R are calculated from measurement of temporal changes in optical density in the images due to precipitated diformazan formed by the reaction of O2-, produced by each PAM, with nitroblue tetrazolium present in the culture medium. To date, values of Rand MAX, measured due to adherence of PAM to the dish, have been compared to values obtained when quartz, coal mine dust (CMD), and kaolin . were added to the medium (in vitro). Rand MAX have also been calculated for PAM lavaged from animals exposed to quartz and CMD in the WVU Inhalation Facility. Presently, experiments are being done using which will permit PAM to be restirnulated by different dusts to help establish a dose response relation~ p and a means to study the role of lung surfactant on modifying the acute toxicity of inbaled dusts. Ultimately, this methodology should provide useful insight into establishing the role of 02 in PAM dysfunction due to inhalation of dusts, and in lung diseases such as pneumoconioses. INTRODOCTIONPAM are free cells found in the lungs which protect the lungs by removing foreign debris and bacteria. This is accomplished, in part, by the process of phagocytosis, whereby foreign matter is internalized into vesicles known as primary phagosomes. Phagocytosis also involves the chemical breakdown of inhaled dusts and the killing of microbes. Detoxification is aided by the respiratory burst, which is a metabolic response of the cell to foreign substances, that results in the production of highly reactive oxidizing agents from the partial reduction of extracellular oxygen to superoxide (02) at the surface of the plasma membrane. Superoxide undergoes either spontaneous or enzyme catalyzed dismutation reactions to form hydrogen peroxide (H202) and subsequently hydroxyl radical (OH•) and singlet oxygen (02 t ). However, while these oxygen metabolites aid in the killing of microbes they also may destroy endogenous tissue. For example, 02 has been linked to the aging process and to many diseases including emphysema, diabetes, and cancer.'' Therefore, a better understanding of the production of 02 is extremely important since an abnonnally low production could result in damage by inhaled dusts and bacteria while an abnormally high production could result in direct damage to the lung tissue by the phagocytes. Inhalation of respirable sized mineral dusts, such as quartz (silica), coal mine dusts (CMD), and asbestos, results in various pulmonary disorders. PAM are thought to play an important role since evidence suggests that the first step in fibrogenesis is an interaction of dust particles with PAM. Generally, in vivo exposure of animals to mineral dusts results in increased respiratory burst activity, migratory patterns, phagocytic behavior, and secretory potential of PAM, and for this reason these have been implicated to be pivotal events in the pathogenesis of pulmonary diseases.1 In addition to stimulation of resident PAM, an influx of monocytes into the lung and/or production of new macrophages generally occurs in response to fibrogenic dust inhalation. Further, PAM may attract and stimulate fibroblasts, which normally synthesize proteins and collagen during rep~ of tissue, by secreting chemoattractants and enzymes. Thus, PAM may be involved in pulmonary disorders through failure or partial loss of their defensive capability, or indirectly, through release of other mediators."

Jan 1, 1990